Search Documents

By Jason Saldanha, Andrew Evans, Jonathan Baber

"INTRODUCTION The need for a new road crossing at Silvertown is the result of three key drivers:- •,Severe congestion and delay at the Blackwall Tunnel and surrounding road network; •,A lack of network resilience and reliability resulting from a lack of alternative road crossings in east London and the impacts of unplanned closures; and •,The need to support substantial economic development in east and south-east London (jobs and homes) These drivers directly informed the main objectives for a road-based river-crossing solution. The traffic-related problems at Blackwall Tunnel are long-standing and before Transport for London (TfL) assumed control for the strategic road network in London in 2000 the Department for Transport (formerly Dept of Transport) had investigated various relief options including a third tunnel bore and new bridge. This resulted in a new crossing alignment being safeguarded (by direction of the Secretary of State for Transport) and this was refreshed in 2001 in favor of TfL. In recent years (since 2009) TfL as part of the East London River Crossings Programme has undertaken detailed optioneering and feasibility work to address the above ‘need’. This led to the conclusion that a new road tunnel would offer the best solution in preference to bridge, ferry or demand management options. In 2012, in response to a formal request by the Mayor of London, the Secretary of State for Transport confirmed a new road crossing at Silvertown as a Nationally Significant Infrastructure Project (NSIP) by Section 35 direction under the Planning Act 2008. This NSIP designation meant that TfL as scheme promoter must comply with the National Rail and Road Networks National Policy Statement (NNNPS) and must seek the necessary powers to build and operate the crossing by means of a Development Consent Order (DCO) under the Planning Act 2008."

Jan 1, 2016

By Carl E. Williams

During the past two years a computer program called "COPOR," Computerized Open Pit Optimization Routine, has been developed and used for mine planning of several base metal deposits. This routine utilizes a three dimensional computerized block model of an orebody, some economic parameters and operating constraints to locate the mineable or economic limits of the deposit schedule the yearly production from the mine and produce bench by bench ore reserve summaries and maps of the yearly and ultimate pit configurations. The moving cone method is used to perform these functions with a conventional block model. This model is conventional in the sense that each block is assumed to be homogenous; i.e., either ore or waste but not a mixture of the two. Due to the nature of a seam type deposit this approach is not realistic; therefore, revisions have been made to form a new version of the COPOR program. This version has been named "COALOR," Coal Optimization Routine. COALOR contains all of the power of the COPOR program but is equipped to handle the intricacies of coal seam type deposits. The deposit can be composed of a single seam or multiple seams which are horizontal or dipping at any angle. The numerous coal quality values can be incorporated to aid the optimization of the economic pit limits and yearly scheduling.

Jan 1, 1978

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By M. C. Mound

A recent development using XRD techniques, a unique fixed detector, specifically permitting full mineralogical information simultaneously for the first time, specially designed sample preparation and presentation system and Rietveld codes provide a continuous real- time analysis on the true contained mineral polymorphic composition of powder streams such as ore materials, cement, ground clinker or any other mineral stream conducive to XRD analysis. There are several COSMA systems currently operating in the US, Canada, Italy and Australia, proving service and reliability of this concept. The mineralogical information generated continuously in real time is used for automated efficiency, product quality and reduces costs. Quantitative Phase Analysis information is transmitted to the plant DCS via Modbus over RS422 or ethernet. Some limited information is stored in the on-board computers for optional future use at the operator?s option.

Jan 1, 2010

By R. Mishra

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solutions. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors will demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning.

Jan 1, 1977

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By V. O. Tenorio, K. P. Hague

Mines are constantly trying to improve production processes by optimizing work cycles, reducing operational delays, minimizing costs, controlling equipment utilization, and preventing occupational hazards. Currently, advances in digital mining technologies within the concepts of 5G and Industrial Touch Internet are allowing better control and monitoring of underground mining equipment, with centralized control systems that unify data analysis for proper decision making. A wireless 5G-based platform for controlling and monitoring systems for underground mine operations can be designed over a comprehensive layout in where bandwidth selection, sensor location, Wi-Fi repeaters and power distribution are put together to build a successful supervisory system. In order to confirm the validation of these concepts, a case study is proposed for a medium-sized underground mine with a multi-level network which includes tablets managed by production supervisors, along with other data collection devices installed in semi-autonomous mining equipment, collecting, and distributing data in near-real time, with interconnection to support and services areas on the surface.

Mar 2, 2022

By C. Opoku-Ware, M. Kukay, P. Conrad, F. Inkoom, R. Pal

Researchers at Montana Tech are investigating the potential for developing trees tolerable to degraded un-reclaimed mine site tailings and soils as a solution to re-establishing long-term tree growth on those sites. This project involves growing tree seedlings from seeds planted in the degraded mine tailings and soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in degraded tailings and soils in Butte, Montana with minimal post-planting human intervention. Work conducted on the project to date has shown successful growth of seedlings in degraded tailings and soils. INTRODUCTION In an effort to improve Butte Area One natural resources, this research project is working to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU) (Opoku-Ware, et al 2018). Research by Blicker, et al (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic values (Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown to seedlings in a greenhouse located on Montana Tech’s campus which will be planted in degraded soils located within the BPSOU. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. The trees will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow. The project combines research with tree seedling growth to provide a resource for Butte that could produce thousands of tree seedlings each year adapted to the harsh climate, soil, and tailings conditions that exist in the BPSOU where they will grow. It is anticipated that the trees developed by the project will have the capability for long-term survival and growth because they will be germinated and grown into seedlings in the degraded soils and tailings collected from the BPSOU where they will be planted. Soils and tailings collected for the project have been evaluated to determine if they lack nutrients or contain substances potentially toxic to the long-term growth and survival of the trees. Toxic levels of metals, high concentrations of soluble salts, extremes in pH, nutrient deficiencies and imbalances, surface crusting, high bulk density, low infiltration rates, high surface temperatures, low cation exchange capacity, restricted microbial activity, low water retention, harsh climatic conditions and surface particle movement are some of the traits of mine tailings sites that restrict revegetation efforts (Barth, 1986).

Jan 1, 2019

By John F. Slonaker

This report is a review of current research being conducted in the United States which is intended to increase the utilization of coal ash. In order that this report be as timely as possible, the majority of information was obtained by direct comunication with the people listed in the references. Due to the magnitude of the flyash research program, some projects may be inadvertently omitted. Field research on flyash for use as an agricultural fertilizer is being monitored at Virginia Polytechnic Institute and State University.1 This research is directed at determining the plant nutrients that are available in flyash as well as the quantities of flyash that can be applied to agricultural soil without adversely affecting plant growth, Coal mine spoil and refuse bank reclamation with power plant flyash is being demonstrated by United States Bureau of Mines, Morgantown, West Virginia.2 Numerous highly visible coal refuse piles and strip mine spoil banks contribute to air, water, and land environmental problems. Revegetation of several experimental sites with flyash from bituminous coal-fired power plants was undertaken in West Virginia and Pennsylvania. Conventional farm equipment was used at some of the sites while large earthmovers were required at others. The flyash served as a neutralizing agent, dilutent, and soil amendment to provide some nutrients which enhanced vegetation of the barren areas, Estimated cost of reclamation by this method is $300.00 per acre of previously leveled area. This figure can vary considerably depending upon the topography of the site, haul distance, quality of the soil and quality of flyash.

Jan 1, 1974

By Anna Sieminska-Lewandowska, Monika Mitew-Czajewska

"The construction of 6.3 km long central part of 2nd metro line in Warsaw was completed in September 2014 (7 stations - out of which three 25m deep stations - built using cut and cover method; two single-track tunnels constructed using four EPB TBMs as well as a short NATM section with soil freezing below the existing road tunnel). Central section of the 2nd metro line was opened to public after verification and testing in March 2015. Design and build tender for the extension of this line in East (three stations) and West direction (three stations) was announced with total length of running tunnels – approx. 5 km. Detailed description of a very complex geotechnical context, different construction methods, challenges encountered and solved during construction and finally lessons learnt on this interesting project are presented in the paper. DESCRITPTION OF THE PROJECT Introduction The very first concept plan of the metro system in Warsaw was designed several years after regaining independence by Poland in 1918. In 1929, following the geotechnical survey, design works begun, but the economic crisis of the 1930s stopped it. After a few years of break, in 1938 a coherent concept of the metro network was proposed to be implemented in phases over the next 35 years. In total, construction of 46 kilometers of metro, including 31 km of tunnels and 15 km on surface, was planned. Unfortunately, World War 2 made the implementation of those plans impossible. In the post-war period several metro designs were elaborated, but none except one was scheduled for implementation. Construction of the 1st, 23.1 km long, North-South line commenced in 1983 and finished in 2008 (Sieminska-Lewandowska et all. 2009). Nowadays, Warsaw covers the area of 517 km2 and, according to year 2014 statistical data, the city has much more than 1.7 million inhabitants. Only one operating metro line is not sufficient for such a populated city. Up-to-date metro plan, shown on Figure 1, includes also 30.5 km long 2nd metro line. It’s route is divided into four sections: Western Section with the length of approx. 9.2 km and 9 stations, Central Section with the length of 6.3 km and 7 stations, North-East Section with the length of 7.7 km and 6 stations, South-East Section with the length of 7.1 km and 6 stations. The construction of the central part of the 2nd metro line in Warsaw was completed in September 2014 and its operation started in March 2015. The paper focuses on challenges encountered and solved and lessons learnt during construction of the central part of the 2nd metro line in Warsaw."

Jan 1, 2016

By Craig M. Sams

Matching mill? drives to mill power draws is a relatively new practice with the introduction of variable speed drive arrangements. Semi-autogenous grinding (SAG) mills are the focus of this paper as ball and rod mill characteristics are easily charted as charge loading and speed change. In addition, a look at types of drives available in the market and mechanical ratings is outlined to match the specifics of each drive.

Jan 1, 1991

By Roshan B. Bhappu

Stimulated by current $0.80 to $1.20 per pound price tag of copper, considerable interest and activity have been generated in the copper mining camps throughout the world, and especially in the Southwestern United States and Northern Mexico copper belt. Under these economically favorable conditions, many of the marginal oxide-copper deposits, as well as newly discovered prospects, are under scrutiny for possible exploitation. For both the known deposits and new prospects, the big question facing the mine operator is the selection of the best method for processing these economically attractive oxide-copper deposits. Several variations of the hydrometallurgical processes are currently available for treating oxide-copper ores which can be mined by the open-pit method. Basically, these processes involve preparing the ore for application of an acid solution, applying the solution to the ore, and recovery of the metal from the pregnant solution. Dump leaching, heap leaching, vat leaching, agitation leaching and, in more recent times, in situ leaching or solution mining in combination with well established cementation process or the newly developed solvent extraction-electrowinning system have all been employed or have been investigated for the recovery of copper from oxide ores. Of these processes, dump, heap and vat leaching have been successfully practiced for treating oxide-copper ores. Agitation leaching is a relatively newcomer and has been adopted from the experiences of uranium and gold processing. Finally, the inplace leaching technique is the latest process to be suggested for possible treatment of oxide-copper ores.

Jan 1, 1974

By Kevork Chouzadjian, Gary Davis, Nicholas Katsikaros, Bruce Kelley, Mellie Mavatoi

A process has been developed to recover gold and copper from two waste materials at the Bougainville Copper Limited mine in Papua New Guinea. It involves the bioleaching, in reactors, of a pyrite concentrate to liberate refractory gold and generate sulphuric acid, ferric sulphate and biomass for bacterial leaching of a chalcopyritic waste rock dump. Gold is to be recovered by cyanide leaching and copper by solvent extraction/electrowinning. The reactor bioleaching was developed in continuously operated reactors of 1 m3 capacity by CRA Advanced Technical Development at Cockle Creek, while the dump leaching was developed in 750 kg columns on site at Bougainville Copper Limited. The process was to be piloted on site.

Jan 1, 1990

By H. M. Lima, P. Wathern

There are many different words to describe mine closure, including rehabilitation, reclamation, restoration and decommissioning. Closing mining operations, mainly open pit mines, has required resolution of numerous issues. Mine closure plans involve environmental-protection issues, regulatory issues and community issues. The obvious, and often most expensive of them, is the physical rehabilitation of the disturbances and the elimination of long-term commitments and maintenance. This paper outlines mine closure planning and its important component, mine-site rehabilitation. Community consultation and involvement are also referred to as an important component of the mine-closure plans, which are required to ensure satisfactory mine site rehabilitation. Considerations of socioeconomic impact of mine closure and long-term responsibilities are presented.

Jan 1, 2000

By J. A. Rose, A. S. Atkins

Environmental awareness has become a paramount consideration in the issue of planning and licensing arrangements for the disposal of wastes associated with mining operations. In this con- text the disposal of liquid tailings is a difficult and controversial problem with regard to environmental surface disposal. The paper outlines the use of Information Systems for decision support in the safe and environmental disposal of liquid tailings linked to conventional coarse refuse operations. This offers both an economic and an aesthetic approach to a historical perception of waste tipping in the underground coal extraction industry. The paper will demonstrate a prototype system that incorporates multimedia facilities which include data such as; voice comments, site photography, site plans and fluid flow circuits.

Jan 1, 1996

By M. B. Mooiman

Cyanidation of gold and silver ores by conventional mining and milling techniques has been practiced for over a century. During the past decade, heap leaching has emerged as a viable process for treating certain gold and silver ores. (1) The rapid development of heap leaching for gold and silver ores is largely a result of lower capital and operating costs and faster start-up time than that offered by conventional mining and milling. In general, these features make heap leaching an ideal approach for exploiting either small or large low-grade disseminated deposits of gold and silver considered to be uneconomic by conventional methods. The development of heap leaching technology has evolved from the operations initiated in the western United States. The basic components of a typical heap leaching operation are depicted in Figure 1. Run-of-mine or crushed ore (usually 1 to 5 ppm gold) is delivered to specifically prepared impervious pads. Alkaline cyanide solution is applied to the surface of the heap and allowed to percolate through the heap (typically 10-30 ft high). Pregnant leach solution which drains from the heap is collected and stored in tanks of sufficient size or in collection reservoirs. Gold and silver are recovered from the pregnant solution and the barren solution is recirculated back to the heaps after reagent make-up.

Jan 1, 1983

By Robert A. Bauer

Two basic types of subsidence occur in Illinois: pit and sag / trough. Pits develop over mines less than 165 feet deep and where relatively incompetent strata are found over the mines. Sag subsidence is found over mines as shallow as 75 feet and more generally over mines of greater depths. The percentage of subsidence and angles of draw associated with sag subsidence appear to be controlled by the rock properties at each specific site. The percentage of subsidence and angles of draw are smaller where the sites are not affected by geologic structures. An investigation to determine if a time factor based on the time interval from the date of mining to the subsidence events has shown that simple correlations with time, percent extraction, average pillar stresses, and pillar dimensions is not evident in Illinois.

Jan 1, 1982

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996

By X. X. Shao

Dewatering of ultra-fine clean coal slurry to a low moisture level of20 percent is difficult using the conventional techniques. A novel approach, which utilized mixing of fibrous waste material, such as paper, carpet and wood, with coal slurry prior to dewatering was developed. It was found that addition of about 10 Kg/t of carpet fibers or 5 Kg/t of raw paper pulp lowered the filter cake moisture from 22.5 to 18 percent. The compressive strength of the filter cake improved from 0 to 4.5 Kglcm2 and impact resistance from 0 to 4. The experimental data indicated that the handling character of the dewatered fine coal was improved significantly.

Jan 1, 1998

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014