Search Documents

By E. R. Bauer

The trend in underground room-and-pillar coal mining is to employ remote-control continuous mining machines and extended cuts, 12 m (40 ft) deep or more. This system of coal extraction, adopted by over 435 mines, can create additional worker-safety hazards. To address the ground control and worker-positioning hazards, a combination of statistical analyses and numerical modeling was conducted. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the Coal Mine Roof Rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling to predict roof displacements during extended-cut mining was completed. The paper describes the results of these studies and their impact on the safety of extended-cut mining.

Jan 1, 1999

By Paul Nicholas, Raju Gottumukkala

"India’s economy is expanding with rapid urbanization. Improvement in infrastructure is a keystone to the Indian government’s economic plans, including expansion of transit systems. Most of these systems are designed with elevated and underground sections. New Delhi, a city of 23 million people, suffers from heavy traffic congestion and pollution. The transit (metro) system is seen to be of critical importance. Phase 3 of the Delhi transit system project is 140 kilometers (km), with 40 km of twin-bore tunnels requiring 35 tunnel boring machines (TBMs) for construction. Transit systems are also under design or construction in Chennai, Bangalore, Kolkata, Hyderabad, Jaipur and Mumbai. Most have twin-bore tunnels. At present, 55 TBMs are operating on underground metro construction, and future projects will increase this number. This paper highlights the unique challenges of construction of underground metro systems in highly congested urban environments, using Kolkata and Delhi systems as examples. INTRODUCTION The first transit system in India was constructed in Kolkata (India’s third-largest city by population.) This line is 28 kilometers (km) in length, has underground and at-grade sections, was built in phases, runs north/south, and has 24 stations. This project was sanctioned in 1972, started construction in 1984, and was completed in 1995. The tunnels were constructed primarily by cut and cover methods with some open-face, compressed air shield tunneling. In 2006, the urban transport policy recommended construction of transit rail systems in all urban cities with a population exceeding 2 million. Further, in 2014 the central government stated that it would assist in financing transit systems in all cities with a population of over 1 million. In 2015, the central government approved the development of transit systems in 50 additional cities across India with a budget of $75 billion (see Figure 1). Transit development is just part of a huge expansion in planned rapid transport systems, which include metro, bus, high-speed rail, and monorail systems. Metro systems will include elevated and underground sections with twin-bore tunnels and underground stations. In the Delhi/National Capital Region (NCR), now the largest city in India by population, Delhi Metro Rail Corp (DMRC) was formed in 1995 as a joint venture company between the central government and Delhi state. DMRC operates the Delhi metro system. (see the case studies described later in this paper). DMRC has developed an external function to carry out studies and to offer consultancy to other cities planning transits. Since its inception, DMRC has produced Detailed Project Reports (DPRs) for every metro and monorail project in India. In 2012, DMRC became a partner in the management consultancy for Jakarta Mass Rapid Transit System, its first project overseas. DMRC became a model organization for other cities to follow. These cities have included Chennai, Hyderabad, Kolkata, Bangalore, Jaipur, Mumbai, Ahmedabad, and Nagpur. Other cities (e.g., Lucknow and Patna) are in the metro planning phase. Metro systems are under construction or partially operating in Hyderabad, Bangalore, and Jaipur."

Jan 1, 2016

By Jun Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1997

By T. Acton

The Zarafshan/Newmont Joint Venture is currently operating in the Republic of Uzbekistan producing in excess of 400,000 oz. of gold per year from low grade oxide ore stockpiles adjacent to the Muruntau open pit gold mine located in the Kyzylkum desert of central Uzbekistan. Four stage crushing and screening produces a final product for heap leaching, Merrill-Crowe processing, and local refining for International market export. The Zarafshan/Newmont Joint Venture is the first major commercial project of its kind in the former Soviet Union to be successfully negotiated, engineered & constructed, and placed into continuous operation,

Jan 1, 1997

By V. Rajaram

The Parachute Creek Member of the Green River Formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch Joint Venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1977

By Drummond Earley III

The U.S. Bureau of Mines is currently conducting laboratory experiments to study the reactions occurring during in situ leaching of oxide copper ores hosted by biotite-poor granite and biotite-rich granite porphyry. Detailed pre-leach and post-leach petrographic examinations of the rock samples are combined with the leach solution chemistry resulting from core leaching experiments to enable an evaluation of the various reactions which are responsible for the observed fluid chemistry. The information resulting from these laboratory studies is being utilized to support the design of the Bureau's ongoing field research project at the Santa Cruz deposit near Casa Grande, AZ. Atacamite and chrysocolla are the primary copper minerals present in this deposit, and both are readily soluble in the dilute 5% sulfuric acid solutions used in these experiments. In addition to the dissolution of copper minerals, biotite dissolution also occurs during the experiments, contributing K, Mg, Fe, and Al to the leach solution. The biotite dissolution appears to be non-stoichiometric, as it is progressively altered to vermiculite and finally, amorphous silica. While K, Mg, and Fe concentrations in solution steadily increase with time, Al quickly reaches a maximum, and then remains relatively constant for the remainder of the experiment. This suggests that Al saturation is achieved, and this Is supported by the presence of precipitated Al sulfate and aluminosillcate clay mineralization in the post-leach rock samples.

Jan 1, 1990

By R. J. Sawyer

The Greens Creek underground polymetallic mine restarted production in 1996 from a newly discovered high grade ore zone. Efforts to improve payable gold recovery have focused on gravity separation. The paper compares testwork and plant results for a newly installed gravity circuit.

Jan 1, 1997

By A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in tern of its complexities as well as its value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer based predictions and practical results. Research conducted to compare computer result with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only after more reliable input data are developed.

Jan 1, 1985

By Gary L. Simmons

Noranda's Grey Eagle Mine and Mill, located in the Siskiyou Mountains of Northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mining, milling and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1984

By M. J. Richards

Spontaneous combustion caused by the movement of air through the waste is a major problem. Combat methods attempt to exclude oxygen rich air, but little is known about airflow through the waste. The use of a tracer gas technique to monitor the flow of nitrogen from an injection hole during inertisation is described. Correlations are drawn between barometric pressure changes and the nitrogen entering the waste. As no information was obtained about airflow and oxidation zones, a second experiment was conducted to sample from the waste, but the results were inconclusive. A finite element method developed to model the pressure and airflow distribution, under steady state and nitrogen injection conditions is outlined

Jan 1, 1987

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By James H. Barks

Commercial development of the mineral resources of southwestern Missouri began about 1850 and spread into southeastern Kansas and northeastern Oklahoma, forming the Tri-State Mining District with Joplin as the urban center (fig. 1). The value of the Tri-State mineral production from 1850 to 1950 exceeded one billion dollars, and until 1945 the region was the world's leading producer of lead and zinc concentrates, accounting for one-half of the zinc and one-tenth of the lead produced in the United States (Gibson, 1972 1). By 1950 most of the rich ores had been extracted, and mining and milling operations declined during the 1950's and ceased in the 1960's. The sulfide minerals, mainly galena and sphalorite, were mined from cherty limestones at depths of 25 to 75 m (meters). Crude ores were brought from the mines to the surface where they were milled into lead and zinc concentrates. , Barren rock was discarded in piles while the ore-bearing rock was crushed and ground into fine gravel. The minerals were separated from the rock by a jigging process and the tailings were skimmed off and discarded in large piles. Ground-water flooding of the mines was controlled by constant pumping. When pumpage declined in the 1950's and 1960's tile abandoned mine drifts and shafts filled with water. At present (1977) numerous tailings piles and flooded mines remain as visible evidence of the mining era and as a threat to the quality of ground and surface waters of the area. In 1976 the U.S. Geological Survey in cooperation with the Ozark Gateway Council of Governments made a study of the effects of the mines and tailings piles on water quality in the Missouri part of the Tri-State District. The study area covers approximately the southwestern quarter of Jasper County, an area of about 725 km2 (square kilometers), and is bounded by long 94 o 15' w.' and the Missouri-Kansas state line, and lat 37 o 15 N., and the Jasper-Newton County line.

Jan 1, 1977

By G. A. Calboreanu

The deterioration rate of any metal or alloy is increased in a erosion-corrosion application because the passivated surface layer is removed by the solid particles contained in the pumping fluid and the material surface becomes corrosion active again. Numerous attempts were made to engineer a stainless steel with higher hardness and unaffected corrosion performance. Alloys of special interest in such an area are the duplex stainless steels particularly the CD4MCu material which has the capability of being hardened due to its ferrite-austenite microstructure. Unfortunately, the CD4MCu with higher hardness comprises different intermetallic compounds which will increase the corrosion rate. The paper is analyzing the erosion-corrosion performance of a new type CD4MCu with 32% higher hardness and superior wear performance. The corrosion performance of this new alloy is better than the corrosion performance of the common CD4MCu material which the industry could supply. The corrosion effectiveness was evaluated with the Huey test, the potentio-dynamic anodic polarization test and the weight loss test whereas the erosion resistance was established with a low stress ball-on-disk type apparatus. The Wilfley hard CD4MCu material had 39% lower weight loss and 32% smaller volume loss than the common CD4MCu alloy The hardness range of the centrifugal pump parts poured and processed with the Wilfley hard CD4MCu is 320-350 HBN versus 250-255 HBN hardness of the common CD4MCu. After approximately 18 months of experimentation and field testing it was clearly established that the life time of the Wilfley hard CD4MCu is higher than the common CD4MCu and consequently centrifugal pumps were supplied to different customers in North and South America. India and more recently Australia. Sincere thanks to all the A.R. Wlifley & Sons Inc. and Western Foundries Inc. employees who supported and help to implement this work. special thanks to George Wilfley. Dave Cobb. Bill Becker Sr. and Wayne Taylor

Jan 1, 1997

By D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming mineral. A polymeric depressant is then added to attach to this re-surfaced mineral. Nearly 200 flotation tests with a 11 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother-collector system, grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1994

By Francois E. Heuze

This paper summarizes the geomechanics programs conducted in two hard rock underground mining operations in the Western United States, between 1966 and 1981. The two projects were directed towards understanding the behavior of the rock masses, at the scale of the caverns. To this end, the emphasis was put on large scale field measurements, complemented by limited laboratory testing. The results of these observations were used to build realistic finite element models of the underground chambers. In the marble mine, at Crestmore, California, the models were applied to the structural optimization of the room-and-pillar pattern. In the granite mining, at Climax, Nevada Test Site, the models explained some unusual stress changes observed during excavation. Based on the large number of geomechanical techniques employed, specific conclusions and recommendations are offered regarding the quality, applicability, and usefulness of the various methods. The two case histories clearly indicate chat numerical models are extremely useful for a detailed understanding of the structural behavior of mine openings. To be realistic, these models must be based first and foremost on large scale field observations. The lessons Learned on these two projects also are directly applicable to the design and analysis of nuclear waste repositories in hard rocks such as basalt, granite, and welded tuff.

Jan 1, 1982

By Arash Nikvar-Hassani, Lianyang Zhang

To address the drawbacks of the conventional portland cement/fly ash (PC/FA)–based cementitious material currently used in practice to construct pumpable roof supports (PRSs), a novel cementitious material has been developed based on geopolymerization technology. The novel cementitious material is comprised of two pumpable grout streams: Stream 1 is a slurry composed of pozzolanic material and high-calcium additive and stream 2 is an alkaline solution comprised of a gelling agent. Biopolymer has been added to the second stream to provide ductility to the geopolymer cementitious material. In the laboratory scale, systematic experiments have been carried out to investigate the viscosity, setting time, and uniaxial compressive strength (UCS) of the new cementitious material and develop the right recipe for field applications. By collaborating with industry and the National Institute for Occupational Safety and Health (NIOSH), full-scale PRSs have been constructed and tested. The results show that (1) the novel cementitious material based PRSs has much higher peak UCS and similar or higher residual strength than the conventional PC/FA-based PRSs; and (2) unlike the PC/FAbased cementitious material, the novel cementitious material shows good long-term durability with nocracking/disintegration when exposed to air.

Jul 1, 2023

By Robert R. Dorfler

AMPS[. has completed a rationed grinding ball test in a 2.93 m x 2.93 m ball mill at Climax Molybdenum Company. The test consisted of purging the ball distribution formed by charging 100%, 76 mm carbon steel balls with a distribution formed by charging 50% 76 mm and 20% 51 mm alloy steel balls. The resulting change in ball surface area yielded improvements in both tons ground and fineness of grind with a significant reduction in total ball consumption. This paper summarizes preliminary studies leading to the plant test, grinding efficiency results, and future plans to optimize the ball charge.

Jan 1, 1981

By W. H. Jang

Recent research has demonstrated the utility of the FTIRIIRS adsorption density equation for in-situ study of surfactant adsorption phenomena at the surfaces of reactive internal reflection elements (IREs). The FTIR/IRS adsorption density equation is given by (formula) where r is the adsorption density, A/N is the absorbance per reflection, e is the integrated molar absorptivity, 4 is the bulk concentration of the surfactant, d. is the effective thickness, and dP is the depth of penetration. Previously, the validity of the adsorption density equation had been confirmed only from solution depletion measurements with high surface area powders. Now, FTIR/IRS studies of Langmuir-Blodgett (LB) monolayer films of fatty acid transferred to the surface of a calcium fluorite IRE .clearly validate the reliability of the FTIR/IRS adsorption density equation for quantitative analysis of surfactant adsorption. In addition, it was confirmed from the observed absorption band at 1550 cm-1 that the first monolayer of the transferred fatty acid chemisorbs at the surface of fluorite.

Jan 1, 1994

By Abdelaziz Baçaoui, Imane Aarab, Mohammed Derqaoui, Abdelrani Yaacoubi, Khalid El Amari, Abdelmoughit Abidi, Abderahman Etahiri

Numerous researchers have addressed the complexity of the direct flotation separation of apatite from low-grade phosphate ore. The majority of these studies were limited to the micro-flotation scale. In fact, there is no warranty that a reagent scheme that showed a direct flotation of apatite at a micro-flotation scale on pure minerals would automatically replicate the same expected results on the natural ore in the mechanical flotation cell and so was the case for the phosphate ore studied. The overall trend was concentrating apatite in the non-float product. This study aspired to thoroughly assess the flotation performance of this never-exploited low-grade sedimentary phosphate using design of experiments (DOE). Unveiling new insights on such a strategy twist, various parameters and operating conditions, namely, desliming, type of collector and depressant, reagents dosages, conditioning times, flotation time, and pH, were addressed by multiple-factor screening using asymmetrical fractional factorial design followed by statistical interpretations. The collectors tested were the sodium oleate and a fatty acid mixture (FAM). The depressants tested were sodium alginate (NaAL), corn starch, carboxymethylcellulose (CMC), and sodium silicate. The results of the multivariable analysis revealed that desliming, pH, collector dosage, and flotation time significantly influenced the flotation process. Desliming was beneficial for the yield, P2O5 recovery, and SiO2 removal; however, there was still a compromise between grade and recovery. A strongly alkaline pH value of 12 stood out from the whole range. P2O5, CO2, and SiO2 grades of the products and flotation recoveries were improved, except for P2O5 recovery, which was negatively affected. A collector dosage between 2000 and 3000 g/t increased the P2O5 grade and reduced CO2 grade and recovery, enhancing the apatite/carbonates separation. A flotation time of 15 min was significant for P2O5 grade and CO2 recovery, nevertheless, at the expense of yield and P2O5 recovery. The products having initial concentrates of 28.08% P2O5 with a recovery of 88.96% and 29.41% P2O5 with a recovery of 62.71% were obtained using 25 g/t of NaAL and 2000 g/t of the collector FAM and sodium oleate, respectively, at pH 12.

Jun 5, 2022