Search Documents

By M. M. Foss

Geophysical methods are gaining acceptance in the evaluation of coal mine ground control condition. The use of in-seam seismic investigations has contributed significantly to the body of information concerning ground control feature identification and analysis. Seismic methods have been used successfully in locating voids, faults, fracture zones, roof and floor rock interfaces, and more recently in characterizing in-seam stress distribution. Seismic tomography is an effective tool in data interpretation for several of these applications, but as is the case with other engineering application of geophysical techniques, there are limits as to how much substantive information can be interpreted from a given data set. This paper discusses some of the applications of in-seam seismic geophysical tomography, and the limits to which the transformation from raw data to information should be taken.

Jan 1, 1995

By Joel K. Waterland

GENERAL DESCRIPTION Homestake Mining Co.'s operations are at Lead, SD. Production from the various methods used are: 1 155 753 t/a (1,274,000 stpy) by open cut-and-fill, 68 039 t/a (75,000 stpy) by square set cut-and-fill, 144242 t/a (159,000 stpy) by shrinkage stoping, 107 048 t/ a (118,000 stpy) by blasthole stoping, and 67 132 t/a (74,000 stpy) in development work for a total of 1 542 214 t/a (1,700,000 stpy). Mining takes place from the 616-m (2000-ft) level to the 2073-m (6800 ft) level (Fig. 1). The average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip of Ore Body Six major ledges varying from 914 m (3000 ft) long by 228.6 m (750 ft) wide to 305 m (1000 ft) long by 122 m (400 ft) wide are mined. Within these ledges are irregular-shaped areas of varying sizes. These ledges dip at approximately 1.2 rad (70°) to the east and plunge to the south from 0.26 to 1.57 rad (15° to 90°). Ground Conditions The ore is cummingtonite (chlorite schist) which is very competent except for major bedding planes and fracture patterns. The footwall is a slate but because of the dip presents very few problems. The hanging wall is also a slate which because of the dip and bedding is very weak and requires considerable rockbolting. No problem has been encountered with rock bursts to a depth of 2438 m (8000 ft). Ore Value The ore values vary somewhat from ledge to ledge, but the average ore delivered to the mill is approxi¬mately 6.2 g (0.2 oz) of gold per ton. A small amount of silver is the only byproduct of this operation. Annual production of gold is approximately 10 575 183 g (340,000 troy oz). Production Requirements The mine has a mill capacity of approximately 1 723 651 t (1,900,000 st) but because of several fac¬tors (manpower, depth, etc.) this mill capacity has not been attainable for the past several years.

Jan 1, 1982

By V. Badaker, R. J. Sweigard, C. D. Barton, J. W. Stringer, J. M. Ringe, A. D. True, D. H. Graves

Field studies have demonstrated the relationship between the growth of high-value trees on surface mined land and the physical conditions of the root growth medium. Specifically, the survival and height of hardwoods grown on less compacted material are far superior to those grown on compacted material. Furthermore, studies have demonstrated that the physical condition of the root growth medium can be characterized by dry bulk density and penetrometer resistance and that these parameters are also related to tree growth measurements. Site indices are useful for evaluating and predicting the productivity and timber yield for a specific location. A method has been proposed to estimate the site indices for various tree species on reclaimed surface mined land as a function of the physical properties of the root growth medium.

Jan 1, 2005

By C. Van Landingham, A. Bailey, R. A. Schoof

A residential metals abatement program has been underway in Butte for more than 20 years. More than 1,350 yard and attic cleanups were completed by the end of 2018; most triggered by lead. While the focus is on remediation of residential soil and house dust, the program also includes a blood lead monitoring program with identification and abatement of additional sources of exposure for children with elevated blood lead levels (BLLs). As specified in the remediation program, studies are being conducted every 5 years to assess BLL data collected from Butte children. The first two studies have evaluated over 6,000 BLLs from 2003 through 2017 and evaluated trends over this time period, by Butte neighborhood, and as compared to areas outside of Butte. These studies showed that rates of elevated BLLs (i.e., those above 5 µg/dL) in Butte children have declined dramatically since 2002 but have been declining much more slowly since 2011. Improved rates of confirmation testing are needed to verify the rates of elevated BLLs. While the RMAP likely has contributed to these declines in BLLs the magnitude of impact cannot be quantified.

Mar 2, 2022

By R. A. Deju

The Basalt Waste Isolation Project of the U.S. Department of Energy is a part of the National Was re Terminal Storage Program. Its mission is to assess the feasibility of siting a nuclear waste repository in the basalt formations which underlie the Hanford Site of the U.S. Department of Energy. The progress in all program areas is summarized in this paper. Activities conducted to date have led to the identification of possible repository candidate sites within the Hanford Site.

Jan 1, 1981

By D. E. Healy

In 1989, an autogenous grinding task force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding (SAG) at the National Steel Pellet Plant in Keewatin, MN. Pilot plant test work, performed by the Hanna Research Center (HRC), indicated that fully autogenous grinding with pebble extraction and crushing could be incorporated into the existing circuits. In 1990, one of the existing 10 grinding mills was converted for an in-plant test incorporating pebble crushing. Full-scale test work were conducted in 1990 and 1991. They verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit using pebble crushing being greater than throughput of the existing SAG mill circuits. The plant produces 5 Mt/a (4.9 million ltpy) of iron ore pellets from 17.6 Mt (17.3 million It) of crude taconite. Crude ore is single-stage crushed by gyratory crushers. Primary grinding is performed by 10 semi-autogenous wet grinding mills. Secondary grinding is performed by five ball mills. Induration is with an Allis Chalmers grate-kiln pelletizing system. The primary grinding circuit consists of 108.2-m-diam x 5.5-m long (27 ft-diam x 18-ft) SAG mills. The mills are charged with 127 mm-diam (5 in.diam) steel grinding balls at from 3% to 5% by volume. Ball consumption rate is about 0.55 kg/t (1.25 lbs/lt) of crude ore feed to the mill. Each SAG mill is powered by two 2.6 MW (3500 hp) motors drawing 5450 kW (7300 hp) at 76% of critical speed. The mills are grate discharge with 16 mm (0.6 in.) slotted grate openings when new. The mill discharge is sized on a trommel screen having 4.5 mm (0.2 in.) openings. The plus 4.5 mm (+0.2 in.) oversize material is returned to the discharge end of the mill by a reverse screw auger located in the center of the trommel. The -4.5 mm (-0.2 in.) trommel screen undersize is pumped to magnetic cobbers.

Jan 1, 1992

By J. G. Groppo

Lowering of filter cake moisture of ultra-fine coal to a 20 percent level using conventional vacuum filtration could be achieved using a combination of metal ion and surfactants. Pretreating coal slurry with about 0.2 Kg/ton of a surfactant and 50 ppm of copper or 10 ppm of aluminum ions provided filter cake containing 22.8 percent moisture. The lowering of moisture is explained due to formation of hydrophobic micro-agglomerates which facilitates dewatering.

Jan 1, 1994

By Joseph Moses Botbol

Two methods are developed whereby; (1) mineralogic data can be arranged in order of typicality, and (2) mineralogic data external to a model can be compared with the model and the degrees of association computed. Thirty arbitrarily selected base metal mining districts in the conterminous United States were classified as copper, lead, or zinc districts on the basis of tonnage of the major base metal produced. For each of the copper, lead, and zinc districts binary-occurrence distributions were compiled for primary (unoxidized) and secondary (oxidized) minerals. Primary and secondary minerals were then arranged in order of decreasing typicality. Model copper districts are most typified by primary chalcopyrite, pyrite, and secondary malachite. Model lead districts are most typified by primary galena, quartz, pyrite, sphalerite, and secondary anglesite and cerargyrite. Model zinc districts are most typified by primary sphalerite, galena, pyrite, quartz, and secondary smithsonite and cerus-site. The Park City district was removed from the model and its primary and secondary mineralogy was compared with the model copper, lead, and zinc districts. The primary mineralogy of the Park City district is about equally associated with the model copper and lead districts, but the secondary mineralogy is much more akin to the model copper districts. Thus, with respect to the model data, the geochemical target presented by the Park City district resembles a copper district more closely than a lead district.

Jan 1, 1969

By D. J. Beeby

California's Surface Mining and Reclamation Act (SMARA) was passed in 1975 to identify and protect mineral resources in areas of high land use conflict and ensure reclamation of mined lands. Under SMARA, aggregate resource availability is quantified and compared to forecasted demand in specific market regions. Fifteen regions studied thus far cover 51,800 km2 (20,000 sq miles) and contain 45 Gt (50 billion st) of high-quality aggregate resources that have been legally designated as "regionally significant," providing a measure of protection previously unavailable. SMARA reports and state testimony at local hearings have supplied objective information and helped reduce conflict in mine permitting decisions.

Jan 1, 1987

By Thos. B. Douglas

In 1907, the Oklahoma Portland. Cement Company built a small dry process plant at Ada, Oklahoma, then Indian Territory. This plant was later acquired by the Ideal Cement Company of Denver, Colorado, who in 1918 built a new wet process plant along side the old dry plant. The older plant was later shut down .and eventually razed. In 1955, the Ideal Cement Company decided to increase the production at its Ada, Oklahoma operations. After many studies it was decided to build a complete new plant along side the old, near the site of the original 1907 plant. .The new plant was to have a. production of three million barrels annually while the plant then in. operation had an annual production of two and one quarter million barrels

Jan 1, 1961

By James A. L. White

Although the quantity of native sulphur associated with volcanism is large, production from such deposits represents only a very small percentage of total world production, This paper describes the location of the known deposits, the typical geology of these deposits and the nature of the sulphur mineralization. Methods of treatment are discussed and some comments are offered on the economic position of these occurences in world sulphur markets.

Jan 1, 1967

By Tom Michaud, Rob Albinger, Ian Turner, Michael Rispin

Data transmission, communication, tracking, and the connection of equipment such as gas detectors, cameras, and collision avoidance systems in today's tunnel industry are critical pieces of the constructor's infrastructure. Reliability, flexibility, redundancy, and cost-effectiveness are key in selecting and implementing inte- grated systems. Both wired and wireless components are used to deliver custom solutions and can involve interconnectivity between backbones. Systems integration is important as industry adopts proven technologies from other industries. Case stud- ies are given showing how tailor-made approaches deliver needed functionality, with varying degrees of com- plexity, in various classifications of environment, in order to meet a project need.

Jun 23, 2024

By J. A. Cremeens, D. D. Overton, J. C. Varnier

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County, Colorado, USA were investigated using three-dimensional discrete element modeling methods. Large scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back analysis was conducted using pre-failure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and it afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. INTRODUCTION The Pikeview Quarry is an aggregate quarry located approximately five miles northwest of Colorado Springs in El Paso County, Colorado, USA. The quarry has been operated by several owners since the early 1900s. The Pikeview Quarry has been a major source of construction aggregate for the Colorado Springs area for many years (MSHA 1986). In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy. A large scale slope failure occurred on December 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on September 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure. The objective of this publication is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry. Both mechanisms are given equal credence in this publication. Quarry excavation was a key factor in the slope instability for both failure mechanisms. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability. GEOLOGY Regional and local geology are both important factors in slope instability at the Pikeview Quarry. Geologic structure at the quarry is related to regional mountain building and basin development associated with the Laramide Orogeny and the Rocky Mountains. Lithologies at the Pikeview Quarry are also related to regional trends. Localized geologic features, primarily related to weathering and erosion, have also been major contributing factors to slope instability at the Pikeview Quarry."

Jan 1, 2017

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By William P. Blacutt

This paper describes the strategy, the struggles, and the obstacles encountered during the last two years in the ongoing process to capitalize Vinto. The effort involves the offering of a vertically integrated business package composed of the tin and antimony smelters along with the two principal tin mines of the country. Capitalization: Bolivia's Innovative Approach for Privatization, the Vinto Case provides a summary of hard-earned lessons. These experiences can be success- fully implemented in other nations committed to transforming their state natural resource sector.

Jan 1, 1998

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

By E. Bloomstein

The Lone Tree gold mine is located about 4S kilometers east from Winnemucca on the west flank of Lone Tree Hill in Humboldt County, Nevada. The deposit occurs at the north end of the low, rolling Havallah Hills and is about 1 kilometer south of Interstate Highway 80, in sections 11 and 14, Township 34 North, Range 42 East, Mount Diablo Base and Meridian (Fig. 1). The Lone Tree deposit is outside of any previously established mining district and all lands are owned or controlled by Santa Fe Pacific Gold or affiliated companies.

Jan 1, 1993

By H. B. Miller

By its nature, underground metal mining is unlike any other business in the industrial sector. Operations are continuously exposed to economic risk as a normal consequence of mining due to uncertainties associated with the? deposit, excavation, and ever changing political, regulatory, and market conditions. Out pacing advances in productivity and technology, these conditions have contributed to the steady decline of underground hardrock mining in the United States. This paper investigates the trends and major factors believed to be responsible for this decline. Special consideration is given to changes in direct operating costs, labor productivity, and production capacity.

Jan 1, 1995

By William R. Wayment, Wayne S. Cusitar

INTRODUCTION The process of mining removes valuable and eco¬nomically recoverable minerals from the earth. In the case of hard-rock mining, this process involves breaking and removing ore, while leaving the waste rock or host rock as intact as possible. Prior to mining, ground stresses exist in the ore and the host rock as a result of weight and tectonic forces; for the purposes of this chapter, the ore is considered to support the host rock on both the hanging and footwall sides. Two basic phenomena accompany mining. First, the hanging walls and footwalls tend to move together as the ore is removed. Second, high stress gradients de¬velop in the rock periphery of the opening; the magni¬tudes of the stress gradients vary widely, depending upon the local geometry and conditions. At various times, mining methods have used square¬set timbers, waste-rock backfill, alluvial sand fill, and tailings backfill materials, with or without cement, to replace the loss of support caused by the removal of the ore. Cut-and-fill mining has evolved to use hydraulically placed tailings for the backfill. In the stope, this fill provides massive support to the walls, thereby reducing stresses in the back. It also provides a floor from which men and machines can work to drill and blast, to haul ore, and to scale and bolt the back. In many cases, the addition of cement provides a competent free-standing wall when the fill is exposed during mining of adjacent stopes or during pillar recovery operations. In most cases, the use of fill does not eliminate standard tem¬porary or local roof control measures such as roof bolts and wire mesh. Fill Characteristics It is important that backfill used for ground support be of maximum stiffness in relation to wall closure. The stiffness of the fill is related to its placement bulk density or void ratio. In the case of cemented tailings, this is enhanced by the cement bonds. During stope closure, individual fill particles experience rotation and crushing at point contacts, but they are subject to little relative translation. The stiffness approaches infinity as the void ratio approaches zero, until the ground forces reach equilibrium, and closure stops. The gradation of particle sizes and minimal segregation resulting from good hy¬draulic placement both contribute to a high degree of early stiffness in the closure history of classified tailings backfill. This also implies that the fill should be resistant to creeping under high static loads. All mines experience shock loading situations such as blasting, and many mines experience rock bursts that can apply sudden and very high loads to the fill. Certain conditions of void ratio, particle size, and moisture con¬tent can result in mass fluidization of unconsolidated fill during such shock loading. Two key factors in avoid¬ing fluid behavior are the provision of a well-drained fill through desliming or classification and the achievement of a small degree of consolidation through the addition of cement in ratios as lean as 40 to 1 (2.4% cement). The acceptance of classified mill tailings as backfill material has been enhanced by its relative economy, including its source, preparation, delivery, and stope distribution. Transportation from the backfill prepara¬tion plant on the surface into the stope usually can be accomplished with low power consumption, with low labor costs, with few capital costs, and at high tonnage rates. An additional benefit is a reduction of the storage volume required for surface disposal of the tailings stream, with a resultant improvement in the environ¬ment. The costs of placing cemented tailings backfill generally range from $1.65 to $6.61/t ($1.50 to $6.00 per st) of fill depending upon the cement ratio used. Scope This chapter examines a major backfill program at a mine and mill complex where the backfill facilities are included as a part of the original planning. The backfill preparation plant is intended to make maximum use of remote controls and automation. The logistics asso¬ciated with material storage, handling, and metering in the plant are outlined. Important considerations in specifying equipment for typical service conditions are discussed. The fill delivery system is described, includ¬ing the boreholes, level lines, and stope distribution lines. Stope preparations for fill confinement and drain¬age are described, as are the techniques of placement and distribution. Methods of controlling and directing the flow of drainage water and slimes are presented, along with the facilities and equipment for clarification, pumping, and sludge removal. As shown in Fig. 1, the fill program encompasses most aspects of the mining and refining facilities, so the discussion is brief in each area. The preparation of backfill of a uniform and con¬trollable quality is presented here as a material handling problem. The balance of the presentation concentrates on the logic of the system, the costs where meaningful (in 1977 US $ unless otherwise specified), and some operating "tricks" that have contributed to system per¬formance and reliability. SURFACE PREPARATION PLANT A backfill preparation plant is required on the surface. This plant generates suitable fill material from the stream of mill tailings. Among the functions of the plant are: 1) Slimes are removed to improve the percolation characteristics of the fill; typically, particles finer than 325 mesh are removed from the tailings. 2) Tailings and sand storages are provided so that the steady stream of tailings produced by the mill can be accepted. Provision is made to accommodate the cyclic high-volume demand from the mine. 3) The plant stores the cement and contains meter¬ing and mixing facilities to provide fill of a controllable and uniform quality. 4) The hydraulic backfill delivery system is a part

Jan 1, 1982