Search Documents

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009

By J. D. Morgan

Introduction In 1986, the US economy passed the $4 trillion mark. However, the value of domestically processed materials of mineral origin fell slightly to $240 billion. The value of metals produced from US ores was unchanged at $5.6 billion, as was recycled scrap at $4 billion, while the value of industrial minerals rose slightly to $17.9 billion. Consumer demand strongly affects mining and the US economy is relatively saturated with longlived products. Moreover, in recent years there has been a steady increase in consumer, mortgage, and federal debt, inhibiting new purchases of goods. Motor vehicles and housing are major traditional markets for mineral materials. However, the 242 million US citizens already possess 170 million licensed motor vehicles and 92 million dwelling units. In 1986, domestic motor vehicle production fell 3%, to 11.3 million units, while new housing starts rose slightly to 1.8 million units. Nearly all mineral commodities move relatively freely in world trade. As detailed in Figs. 1 and 2, in the last three decades world production of major mineral materials has greatly increased. At present, substantial excess productive capacity exists not only in the US but also in many other countries. Consequently, the US mineral industry is encountering increasing competition from other sources, along with increasing competition from newer, engineered materials. For example, US production of plas¬tics has risen from 900 kt (1 million st) in 1950 to 22.7 Mt (25 million st) in 1986 - on a volume basis significantly greater than steel. Plastics, too, are mineral-based materials, some 7% of petrochemicals going to their manufacture. 1986 saw increased calls for protection. But President Reagan, in his 1987 State of the Union Message and Economic Report to the Congress, reaffirmed adherence to a policy of free and fair trade. However, he stressed the need for increased efforts to open foreign markets to US exports and to increase competitiveness of US industry US imports of mineral-based minerals in 1986 were valued at $40 billion and exports at $24 billion. Strategic minerals As detailed in Fig. 3, imports supplied a significant proportion of total US consumption of several important materials, including many classified as "strategic and critical." There were no changes in stockpile policy during the year. Congress debated the President's 1985 proposals to reduce stocks of World War II-type materials and to focus more on high technology materials needed for the cutting edge of future military material. But no final action resulted. However, Congressional concern about apartheid in South Africa did result in increasing pressure to limit imports of South African minerals. Meanwhile, the National Critical Materials Council in the Executive Office of the President intensified its efforts to be better able to advise the President. The Defense Production Act provides authority for priorities and allocations, supply expansions, voluntary agreements, and

Jan 5, 1987

By S. H. Jason Choi

The Systems Conveyance and Operations Program (SCOP) is being implemented to convey tertiary-treated effluent to Lake Mead near Las Vegas, Nevada. The Reach 3 Tunnel Project is part of SCOP. The tunnel?s planned location along and across the Las Vegas Wash creates challenging tunneling conditions. A number of feasible excavation and initial support methods are being considered during the final design stage. This paper describes how the tunnel construction options were refined based on anticipated tunneling conditions and compatibility between tunnel excavation and initial support methods. A brief description of the most significant characteristics of the anticipated ground conditions is included for the purpose of discussion.

By M. Nambiar

Due to the remote locations of mining projects and the need for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short-circuit capacity. To cope with this situation, more and more mining operators are considering the installation of appropriately designed synchronous condensers together with power factor correction and harmonic filter systems (PFC & HFS). The installation of such power quality equipment is viewed as a technological advancement in the mining application. An adequate level of short-circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter-driven gearless mill drive systems (GMDs) used for grinding. This paper explores the impact, technical advantage and reasoning for the selection of this advanced hybrid technology to cope with the power system challenges of future mining projects. It also delves into the potential problems and how to address them.

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By John M. Arnold

Several years ago it became apparent to some of our people that; there was developing a very definite need for largee coal reserves in the West to satisfy- the need for fuel for the furnaces of electric generating plants with the rapid development of, the West, of both population and industry, it was impossible for hydro-electrics plants to keep up with the ever increasing demand for electricity. In 1960, Mr. E. R. Phelps, then associated with the engineering department of Peabody Coal Company, began a search for and development of coal deposits in the very remote northeast section of Arizona near the village of Kayenta. Travel to this section of the country was not easy even at this late date, and it was an eight hour drive from Farmington, New Mexico to Kayenta, Arizona, a distance of some 130 miles. The trip was over roads that even' a-horse and wagon had trouble negotiating and a four wheel drive vehicle was about the only type of transportation that could satisfactorily traverse these roads, as testify many badly beaten sedans and coupes that tried it. Since that time a very excellent road has been constructed from Shiprock; New Mexico to Cameron, Arizona where it junctions with another excellent road that runs north to Page, Arizona and the Lake. Powell area and south to Flagstaff, Arizona on highway 66. Kayenta is a small village nestled at the foot of the Black Mesa near its northeast extremities. The coal deposits of interest were on the surface of the mesa. This location presented another problem, as the only trail to the top of the mesa was intended for walking, horseback, or a brave soul In a horse and wagon. Once again the four wheel drive vehicle was about the only answer. To reach the coal deposits you must climb the mesa, which is vertical ascent of some 1,500 feet, and then proceed southward into the bowl of the mesa with an ensuing descent of some 1,000 feet, finally coming to an elevation of 6,500 feet, at which elevation the coal outcrops become apparent.

Jan 1, 1969

By Zephaniah Varley, Dominic Parmantier, Paul Schmall, Richard Martin, Red Robinson

Sequential excavation of the Beacon Hill Station has been accomplished in highly complex and inter-layered sand, silt, and clay soils with multiple perched groundwater tables. Successful excavation has required the installation of a deep dewatering well system used to depressurize sand layers above and within the excavated tunnel faces. In addition, the presence of sand layers in the crown of the Platform Tunnels required jet grouting at depths of up to 49m (160-ft). This paper discusses the design intent, construction, and effectiveness of the dewatering system and the selective jet grouting of sand horizons and shaft break outs for the successful construction of the deepest SEM station excavation ever completed in the United States.

Jan 1, 2007

By Peter Schmäh

Pipe-jacked tunnels are considered for a large variety of applications from water and sewage, cable ducts to challenging pipeline crossings or landfall construction. In most cases, Slurry MTBMs are used to carry out these projects. Continuous further development of technological features for pipe jacking plays a key role to overcome feasibility limits and to meet increased project requirements. As tightened safety regulations in terms of accessibility and escape routes increasingly limit the options of small segment lining tunnels in the diameter range below 4 m, 13 feet, pipe jacking has partially taken over. During the last decades, a growing number of large-diameter and long-distance pipe jacking projects have been completed. Experienced contractors successfully use the technological capacity of the MTBM equipment. The machine and cutting wheel have to be designed according to the ground conditions. Bentonite lubrication and interjacking stations are key factors to keep push forces moderate. For long pipe jacking drives, a so-called push module can be installed in the machine can, to be able to switch from pipe jacking to segment lining in case the machine gets stuck. The overall aim is to provide clients and the tunnel construction industry with safe and economical solu- tions for successful project execution. This presentation will present international milestone projects and will also discuss the latest developments in automation, related opportunities and limitations, and the future of digitization and artificial intelligence in pipe jacking.

Jun 23, 2024

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By U. Paschedag, H. Bussmann

"Bucyrus manufactures the most comprehensive product portfolio of mining equipment worldwide. Its mission is to have a positive, lasting effect on our world. Bucyrus makes sustainable development a fundamental way of doing business through economic, environmental and social initiatives that support, educate and benefit our employees, customers, shareholders and other stakeholders. Our participation in GRI (Global Reporting Initiative), a network-based organization that has pioneered the most popular sustainability reporting framework will be discussed as well as examples will be given on each major field of engagement. Two examples from surface machinery are most fuel efficient haul trucks as well as the Highwall mining system which allows access to coal reserves which are lost not making use of this kind of system. Two examples from underground machinery are Bucyrus’ automated plow systems for the mining of medium and thin coal seams with minimum rock and Bucyrus’ intelligent CST drive system for high-powered armored face conveyors (AFCs) for efficient use of energy."

Jan 1, 2011

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

By Harvey Parker

The International Tunnelling and Under-ground Space Association (ITA) is a nonprofit organization that represents all aspects of the tunneling and underground space industry worldwide. The United States has had a prominent role in ITA since its 1974 inception. ITA was formed as a result of a worldwide survey conducted in the early 1970s by the Organization for Economic Cooperation and Development (OECD). Bill Lucke was in charge of tunnels for the U.S. Federal Railroad Administration and was a member of the organizing committee that created ITA. He became a vice president of ITA. Jack Lemley served as President of ITA from 1983 to 1986. Dick Robbins was very active in ITA and served for many years both as a member of the Executive Council and as First Vice President. Harvey Parker has served as President of ITA for the last three years and will serve as Past President for the next three years. Moreover, there are many individuals and companies from the United States that have contributed significantly to the activities and the success of ITA. There have been several active Working Group Animateurs from the U.S. and there have been significant contributions from many individuals as well as companies from the U.S. Several engineers from the U.S. are currently serving ITA in a leadership role. The Underground Construction Association of SME (UCA of SME) is the official organization representing the U.S.. SME Executive. [ ] Director Dave Kanagy and UCA President Tom Peyton were instrumental in the U.S.?s role at ITA during the last few years. Peyton has been the official delegate to ITA. Henry Russell and Christian Ingerslev are both Animateurs of ITA working groups. This article will introduce ITA and its activities. A subsequent article will describe the ITA in more detail and will discuss the significant role the U.S. has played in the development and success of ITA.

Jan 1, 2007

By Adam Shang Robert Fu

The Yung-Chung-Tunnel in Taiwan, constructed for the Taiwan-East Railway Bureau, collapsed during construction when a water bearing, fractured marble zone was intersected. The inflow was approximately 4,000 liters/second. In spite of 30 relief holes the total inflow into the tunnel remained constant. The pre-excavation grouting through the re-aligned tunnel had to be conducted under extreme flow-conditions. A hot bitumen grouting program was selected for technical and economical reasons out of 13 international proposals. The technical challenges were: grouting under severe flow conditions high formation water pressures to be injected with hot bitumen at high temperatures and pressures The hot bitumen grouting program resulted in a dramatic reduction in the hydraulic conductivity and stabilization of the formation and facilitated a problem-free excavation.

Jan 1, 2007

By P. R. Clifford

Phosphogypsum is a byproduct of the manufacture phosphoric acid. There are approximately one billion tons of phosphogypsum stored in stacks in northern and central Florida. The Florida Institute of Phosphate Research (FIPR) is investigating potential uses of phosphogypsum. These include using phosphogypsum as a road base material, as a soil amendment in agriculture, as a daily cover in landfills, and as a construction material. The results of this research will be presented and will be discussed in light of regulatory barriers to the use of phosphogypsum.

Jan 1, 2002

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, NIOSH conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the research, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This document highlights NIOSH's research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers, and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan, and if appropriate training is provided. DISCLAIMER: ?The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.?

Jan 1, 2009

By Xin Wang, He Shao, Wenpu Li, Yiyi Zheng, Xi Chen, Yurong Gao

This study utilized experimental and numerical simulation methods to investigate and analyze the atomization characteristics of three internal air–water mixed atomizers under different operating conditions. By comparing the research results, the effective dust control working parameters for the application of the selected atomizer in the engineering field were determined. Firstly, the atomization characteristics of the three atomizers were studied using a customized experimental system. The results indicated that nozzle 2 had a wide atomization range, a small atomization distance, and small droplet size; nozzle 3 had a narrow atomization range, large droplet size, and fast atomization speed; and nozzle 1 not only had a large atomization range but also could produce droplets of dry mist size with fast atomization speed, meeting the dust reduction requirements of the Majiliang Coal Preparation Plant. Secondly, Fluent software was used to simulate the atomization process and particle size distribution of the three internal mixed atomizers, determining the working conditions of the atomizers, the required number of atomizers, and the application angle of the atomizers in the internal mixed dust removal system. Finally, the atomized dust control system was applied on-site, achieving a total dust removal efficiency of 90.72% and a respirable dust removal efficiency of 89.75%.

Mar 9, 2024

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By M. Hamarat

Freeport-McMoRan Copper & Gold (FCX) is committed to preserving and enhancing biodiversity in the areas in which we operate. As a member of the ICMM, FCX is committed to implement the 10 Sustainable Development (SD) Principles throughout our business. FCX is also a member of the Wildlife Habitat Council (WHC), a nonprofit coalition dedicated to protecting and enhancing wildl ife habitat. In alignment with ICMM SD Principle 7 and our Environmental Policy, FCX has set a performance goal to prepare a biodiversity inventory in 2010 and land management plan by end of 2011 for all active mining sites. In 2010 FCX established a Biodiversity Task Force to assist sites in biodiversity management; optimize use of resources around the globe; implement FCX goals and targets; and align biodiversity programs with ICMM principles and guidance. The task force consists of Environment and SD Department management, scientists and engineers from FCX sites, and WHC staff. The Task Force recently issued a biodiversity inventory guidance document to set expectations and provide consistency across the sites when developing a biodiversity inventory and land management plan.

Jan 1, 2011

By D. R. Wilburn

This summary of international mineral exploration activities for 2006 draws upon avail-able information from literature, industry and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review. They include budgetary statistics provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and information on regional and site-specific exploration activities that took place in 2006 compiled by the USGS.

Jan 1, 2007