Search Documents

By K. Y. Haramy

Deep coal mines with strong roof and floor rock frequently encounter face and rib bursts. The burst problem is becoming more severe as mining depth increases, prompting efforts to relieve high stress areas ahead of mining. Successful stress relief reduces the occurrence of uncontrolled coal bursts. This report by the Bureau of Mines, U.S. Department of the Interior, presents a review of the most widely used methods to detect and destress high stress zones along coal faces. Stress-related burst problems and destressing efforts at a cooperating mine were investigated. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three- dimensional, multiple-seam computer modeling program, "MULSIM?, was used to evaluate the effectiveness of stress relief methods. Modeling results and guidelines for destressing are presented. Results indicate that dangerously high stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1987

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-cu-yd) transit mixer and a shotcrete spray boon carrier, is used by a two-man crew to transport and place up to 25 m3 (32 cu-yd) of steel fiber reinforced, dry, silica fume shotcrete per 11-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control are performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1992

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By R. D. Wunder

The Chino Mines Company, a Kennecott-Mitsubishi partnership, located in Hurley, New Mexico, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/ concentrator modernization commenced in 1980 and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34.0 kt/d (37,500 stpd). A new concentrator was constructed near the mine using semi-autogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of salable copper.

Jan 1, 1985

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010

By S. C. Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico, is a research and development project sponsored by U.S. Department of Energy, designed to demonstrate the safe containment for disposal of radioactive waste. A mine (repository) is currently being developed 2150 feet below the surface, in a thick salt bed which will serve as the disposal medium. Provision of a proper ventilation system at the WIPP Project is a major priority of those responsible for its design, management, and operations. As an ongoing effort towards this goal, it was decided to simulate the mine's ventilation system using Dravo's MINEVENT computer program. Specifically, the work included the development of the following simulation models: 1. Simulation of the current ventilation system 2. Simulation of the designed ventilation system for the following modes: o Mine Construction mode/shift o Waste storage mode/shift o Fire or exhaust filtration mode These computer models are useful in solving complex ventilation problems likely to be encountered in an R&D project, like WIPP. They are particularly helpful for the development of contingency plans to incorporate during emergency situations, such as fires, fan stop- pages, radiation leaks, etc. Also, they can be utilized when considering expanding certain underground areas to ensure the availability of adequate ventilation.

Jan 1, 1986

By David Atkin

This paper presents methods and results of environmental planning conducted for a proposed coal and iron ore transshipment terminal which would be located on reclaimed land west of Lisbon, Portugal. Oceanographic, navigational, marine, structural, material handling, and financial studies of the terminal were conducted along with the environmental analyses. However, because of the proximity of the terminal to heavily used recreational resources, residential areas, and biologically valuable habitat, anticipating and reducing the environmental effects of the terminal to minimum levels was a very important part of the overall project. The results of the study indicate that even the impacts associated with worst-case conditions would be acceptable because of appropriate pollution control measures and planning.

Jan 1, 1983

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

By Frederick J. Murrell

No other region of the world is enjoying the tremendous growth of power use that is currently being experienced in Asia. Fortunately for the coal industry — particularly in Asia — the power plants being planned or under construction are designed to use coal as fuel. This has produced a significant increase in the demand for steam coal that, in turn, has encouraged many in the industry to develop new coal mines. Indonesia is a country that has enjoyed substantial growth in coal production. This developing country has 195 million people who live on the nearly 13,000 islands. It has quickly emerged as the third-largest exporter of steam coal, following only Australia and South Africa. Almost all coal in Indonesia is mined by surface-mining methods.

Jan 1, 1996

By D. Yokom, T. Katsabanis, E. Tremblay

"The mining industry has always faced the problems of replacing retired mining professionals, retaining their knowledge, continuously developing the skills of local talent and employing under-represented groups. In expansionary scenarios the industry faces the additional challenge of increasing available talent. New talent has traditionally come from current mining programs; however, these programs have been declining in numbers, and those that remain face challenges such as fluctuating enrollments, and reduced budgets. Queen’s University and Northern College have partnered to develop an innovative new program that offers online mining education to engineering technologists seeking to upgrade their skills and obtain a Bachelor’s degree. The high quality, flexible curriculum, offered online, includes a wide range of learning activities that promote interaction (student-to-student, student-to-instructor, and student-to-content), and is enabled by modern learning technologies (an integrated learning platform, as well as a variety of types of purpose-built video, web conferencing, and simulation software). The program issues block transfer credit to college graduates, and consequently reduces the time to completion when compared to other Bachelor’s degrees in Mining. The curriculum has been carefully designed to enhance a balance of technical, managerial, and societal skills for students. The program also includes short summer field school sessions, where students gain practical application skills under the direct supervision of engineering experts. THE NEEDS OF INDUSTRY Canada is the world’s largest exporter of minerals, and the contribution of this sector to Canada’s gross national product is more than three times that of the automotive industry, representing approximately 4% of Canadian GDP (MiHR, 2015)1. According to a recent report by the Canadian Mining Industry Resources Council (MiHR, 2016)2, despite the recent downturn in commodity prices, the industry will continuously need to attract new engineers to replace talent retirements and prepare for the possibility of expansion when the industry recovers. As past experience indicates, the challenges during expansion times are severe and the effects on education counter-productive. For example, during the prolonged expansion cycle of 2006-2012, several new programs were started worldwide, and mining became the profession of choice for many young students. During the subsequent downturn in the industry, many of these programs face dwindling enrollments, placing their sustainability in question. However, there is a continual need by industry to retain employees, as well as attract and train local talent, while providing educational opportunities to its employees. High potential college graduates can find themselves reaching a ceiling in their advancement due to their lack of a University degree. Furthermore, there exists an under representation of women, immigrants, and Aboriginal peoples in the labour force, and engineering fields in general1,2. Traditional mining engineering programs have tried to respond to the needs of industry, as well as meet the needs of students seeking diverse and successful employment careers. These programs tend to cater to the educational needs and aspirations of a general population, and their ability to grow and respond to changing industry needs is constrained by the number of students they can attract, as well as the resources available to them in a steady-state scenario."

Jan 1, 2017

By O. K. Brown

U.S. Borax has two tailings disposal requirements which are uniquely different in many respects, but with the common goal to minimize the impact on the environment, utilize dependable technology and minimize the economic impact. The existing borax mine in the grid Mojave desert of Southern California has gone through a series of changes in tailings disposal practices in the 56 years of operations, The other tailings disposal requirement is a new molybdenum mine, presently in the feasibility phase, in the high precipitation setting of Southeast Alaska. II. Introduction U.S. Borax is faced with two tailings disposals situations, at diverse locations:

Jan 1, 1984

By Paul R. Smith

The theoretical requirements for the flotation d large particles are discussed. A flotation machine is described which has components which meet many of the theoretical requirements for the flotation of large particles. The machine's salient features include multiple fine-bubble attachment, froth level feeding, quiescence, shallow depth, and short flotation time. Test conditions and results are presented for the laboratory flotation of 10 mesh phosphate, 4 mesh potash, and 1/2 inch coal. In addition, test conditions and results of pilot plant flotation of minus 14 plus 35 mesh phosphate and minus 14 plus 150 mesh phosphate are also presented.

Jan 1, 1969

By D. Pearson

About 15,000 tonnes of zinc per year is present in the dusts and fumes produced in electric arc and BOS steelmaking, secondary copper refining and brass ingot making. Apart from the use of some copper-smelter fumes for zinc chemicals manufacture, zinc is not recovered and their disposal by landfill entails some risk of pollution by leach-out. The paper describes processes for recovering the zinc based on leaching and electrowinning. It was shown that the procedures normally employed for purifying zinc-electrolytes derived from primary sources are sometimes ineffective for secondary materials. Alternative process routes are proposed. Source materials were leached with acidic or alkaline reagents and solvent extraction was employed for electrolyte purification in addition to the usual techniques involving precipitation. Examples of integrated flow sheets for specific source materials are presented.

Jan 1, 1980

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels ? from mining and processing to the manufacturing of Anished products. In 2009, the estimated real GDP of the United States decreased by 2.4 percent compared with, and the estimated nominal GDP was about $14.2 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. In 2009, the continued decline of the housing market was reflected in reductions in the production and consumption of cement, clays, construction sand and gravel, and crushed stone (those mineral commodities that are used almost exclusively in construction). Production of mineral commodities associated with the manufacture of goods for the housing market, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard also decreased. Declines in auto-mobile manufacturing resulted in reduced production

May 1, 2010

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden, Yumi Kamiya, Edward B. Ilgren

In many developing countries, asbestos is still used for friction products, insulation, and asbestoscement products. However, there is very limited modern data evaluating the airborne concentrations of asbestos fibers in operating asbestos plants. We have conducted an Industrial Hygiene survey, using state of the art PCM and TEM analysis, of a Bolivian asbestos cement plant that uses crocidolite during the production of roofing shingles and water tanks. The study is the first to use modern analytical measurements in an uncontrolled asbestos environment. Thus, this study offers insight into the historical airborne exposures at asbestos plants operating before modern dust control measures were introduced or airborne fiber levels regulated. The results suggest that fiber concentrations are far in excess of those for which current models would predict the onset of asbestos disease and mesothelioma. Significantly, the plant and community do not have an elevated incidence of asbestos disease or mesothelioma. Airborne fiber levels during comminution and fiber sizing ranged from 100 to as much as 1,000 f/cc. Fiber levels in the mixing, forming and finishing areas ranged from 0.5 to 9 f/cc. Based on the number of overloaded samples and estimates of their concentration, historical estimates of exposure may be underestimated by an order of magnitude. Also, an excellent correlation (1:1) between the PCM and TEM fiber concentrations (for fibers _0.25 um diameter) were obtained, raising questions about the conventional wisdom that the PCM systematically undercounts fibers. The results of this study further indicate that current models may overestimate the risk of asbestos disease and mesothelioma.

Jan 1, 2012

By Piyush Rai, Suresh Kumar Sharma, Punit Paurush

The present study has been conducted in surface limestone mine to select the controllable blasting design parameters affecting the peak particle velocity (PPV) for assessment of ground vibration. The study aims at using two prominent statistical tools, namely, principal component analysis (PCA) and stepwise selection and elimination (SSE) techniques for identifying the key controllable parameters affecting the PPV. For determining the correlation coefficient between blasting design parameters and PPV from 44 field scale trial blasts, multi-variate linear regression (MLR) technique was done. It was found that the PCA and SSE eliminated a huge number of controllable parameters to identify the most important parameters, affecting the PPV. The PCA eliminated 6 number of parameters while SSE eliminated 5 number of parameters, and the coefficients of determination (R2) obtained were 0.616 and 0.584 for PCA and SSE respectively. The predictor equations were evolved, and these equations were used to validate the PPV results for another set of 21 field scale trial blasts. The predictor equations have been found to be fairly accurate in predicting the PPV values. Further, the PCA technique provides very near prediction of PPV with high degree of correlation in comparison to SSE technique. The paper highlights the role of state-of-art statistical tools in selecting the blasting design parameters affecting the PPV in field-scale blasting.

Mar 1, 2021

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977

By Giorgio Höfer-Öllinger, Peter Pointner, Manfred Stadlober

"SUMMARY Investigations from tunnel face are part of risk mitigation measures during the excavation works. With the tunnel equipment, percussion drillings of up to 30-40m can be achieved. Core drillings are state of art method for investigation exceeding 50m. At Koralm base tunnel, up to 270m deep percussion drillings were performed with drilling rigs and accompanied by an intensive investigation program. These investigations consisted of monitoring during the drilling, field tests (with packer, using the preventer, borehole imaging) and in laboratory. Percussion drillings are cheaper and save time of interruption of the excavation progress. INTRODUCTION As part of a proper risk management, horizontal advance drillings during excavation of underground works can be seen as state of art and meet wide acceptance. Core drillings, deep and shallow percussion drillings can be differed. The selection of the type of drilling, meanwhile, causes intensive discussions. On the one hand, only a core drilling allows a direct investigation of the rock mass expected during later excavation works. On the other hand core drillings are expensive in both cost and time – if there is no excavation progress during the investigation measures – in construction time. Percussion drillings can be performed as rapid investigation measure with the excavation equipment (“Jumbo”) allowing two dimensional image of the ground around the cross section. There is some limitation concerning a reasonable depth of approximately 30m and a borehole diameter of 76mm. The applications of preventer, packer or borehole imaging are hardly applicable. By use of a drilling rig depths of percussion drillings of several hundred meters can be achieved relative easily and there is less limitation of the borehole diameter. Installation of a preventer is possible, as well as packer tests and borehole measurements (imaging, gyroscope, borehole geophysics). The gap of information between core and percussion drilling cannot be closed completely, but it can be reduced substantially and sufficiently by combination of an intensive program of measurements and analysis accompanying the investigation works."

Jan 1, 2016