Search Documents

By V. Svalbonas, S. M. Jones, A. Boughey

In June 1998, the world's largest grinding mill, the 40 ft (12.2 m) diameter 20 MW Cadia gearless SAG mill, was commissioned. This was a leap of over40% above the largest operating SAG mill. A significant saving in capital cost gave the incentive necessary for a single mill line at Cadia, resulting in the selection of the 40 ft (12.2 m) diameter mill. Now, after 18 months of operation, this paper will review the significant items involved in the development, design, manufacture, installation, and operation of this mill.

Jan 1, 2000

By C. O. Brawner, J. Kalejta II

The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than about 45°. As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result with less rock fall capacity. The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented.

Jan 1, 2002

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By A. K. Majumder

Particle motion in fluids is a subject of considerable practical importance to engineers working in fields such as hydraulics, river mechanics, chemical engineering and mineral processing. Many mathematical models have been proposed to predict the terminal settling velocities of particles in a fluid medium. The selection of an appropriate mathematical model has, therefore, become a challenging task for practicing engineers. This paper reports on an attempt to identify some of the useful models found in the literature for predicting particle-settling velocities in a fluid under free- and hindered-settling conditions. From this study, it was concluded that there is no well-accepted model validated by experimental data available for predicting particle hindered-settling velocities in a suspension of polydisperse and polydens particles. Collective efforts should, therefore, be made towards developing a hindered-settling model, as this is an absolute prerequisite for many model structures in mineral processing and other engineering disciplines.

Jan 1, 2007

By Peter Zhang, Todd Minoski, Gabriel Esterhuizen, Jack Trackemas, Berk Tulu, Morgan Sears

Longwall mining is a highly productive and efficient coal mining method used in the USA. During longwall retreating, the belt entry must be maintained stable, and any roof fall in the belt entry would jeopardize mine safety and substantially interrupt the continuous production of coal in the longwall face. Past experience of longwall mining has shown that belt entry stability was the greatest challenge in longwall ground control, and the occurrence of roof falls in belt entries was largely associated with high horizontal stress. To properly support the roof in the belt entry, it is important to understand how longwall-induced horizontal stress changes affect roof stability in belt entries and to strategically install supplementary support to prevent any potential roof falls. Researchers from the National Institute for Occupational Safety and Health (NIOSH) performed horizontal stress measurements in the immediate roof of the belt entries for two Pittsburgh seam longwall panels oriented unfavorably to high horizontal stress. Hollow inclusion cells (HICells) were installed in the immediate roof at the intersection in each of the belt entries, and stress changes were monitored as the longwall face was approaching and passing the intersection. Numerical models were set up to calculate the longwall-induced horizontal stress changes in the roof at the monitoring sites. With the verified model, investigations were made of how horizontal stress is concentrated and relieved in the belt entry roof near the face under different panel orientations. Both measurements and modeling results showed that high horizontal stress is concentrated in the roof in the belt entry within about 15 m outby the face when a longwall panel is unfavorably oriented to the major horizontal stress. The study demonstrated that longwall-induced differential horizontal stress can be used as an indication of the degree of horizontal stress concentration. Roof support strategies are discussed on how to maintain the stability of belt entry under high horizontal stress concentration.

Jun 14, 2022

By Susumu Uchiyama

This machine was manufactured for excavation of the Roppongi station of the Tokyo Metro Line 12. This machine can excavate both the platform and the rail track at the same time in locations where the traffic is congested and has following features: A multi-centered TBM of the size of 7.06(H) x 13.18(W) m The world first H&V TBM, with right and left machine parts articulated vertically and separately for position control A large erector for simultaneous erection of column and central segments of special shape to construct a highly reliable tunnel This paper reports the design concept, construction, and work record.

Jan 1, 1999

By Michael R. King

The application and use of steel fibre reinforced concrete in precast tunnel lining design is a growing trend due to its advantages in performance over plain concrete, and ease of manufacture compared to traditionally reinforced concrete. However, the design process and performance characteristics of the material are poorly served by current codes and standards. This paper provides some basic design guidance for segmental linings, and compares the material properties for the different material options. A typical example is considered to compare the possible results of lining arrangement and thicknesses for a plain, reinforced, and fibre reinforced design solution.

Jan 1, 2005

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10µm. The current study examined the effects of operating conditions on centrifuge performance. The test conditions included centrifuge bowl and scroll speeds, volumetric feed rates, solids concentration, and pond depth. Centrifuge performance was evaluated using partition curves, along with product yields and solids concentrations.

Jan 1, 2000

By W. D. Monaghan

Flame cutting and welding is one of the major causes of fires and explosions in underground U.S. coal mines. On May 20, 2006, a flame cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On January 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame cutting and welding operation at the Loveridge Mine caused a fire that resulted in sealing of the mine for an extended period. Finally, on March 19, 1992, an explosion at the Blacksville No. 1 Mine that was caused by welding resulted in four fatalities. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame cutting and welding operations to determine the root causes of these types of fires and explosions. The methodology included interviewing mining personnel who perform flame cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations, and MSHA reports of investigations and accidents statistics were analyzed. The results were used to identify and compare differences between flame cutting and welding practices and techniques in small and large mines, Eastern and Western mines, low seam and high seam mines, room and pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices and interventions were developed to reduce the number of fires and explosions caused by flame cutting and welding. This paper provides a summary of this work. Disclaimer: The finding and conclusion in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupation Safety and Health.

Jan 1, 2009

By Gary Brendel

India produces about 70 Mt/a (77million stpy) of coal ash (fly ash and bottom ash) from burning about 200 Mt/a (220 million stpy) of coal for electric power generation. The average ash content is 35%. In contrast, the United States produces about 70 Mt/a (77 million stpy) of coal ash from burning 800 Mt/a (880million stpy) of coal for power generation. Its average ash content is less than 10%. In 1998, GAI Consultants Inc.(GAI) embarked on a federally funded, multiyear project to assist the government of India in solving its growing coal-ash management problem.

Jan 1, 1999

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The fundamental importance of comminution by high-pressure grinding roll (HPGR) technology to efficiently increase the particle surface area lies in lower energy and water consumptions for iron ore pellet feed production. This study compared the ball wet milling process with the innovative HPGR processing technology for hematite-goethite ores. Green-pellet balling and induration processes were simulated on the bench and pilot scales.

By B. A. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformation. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, timelapse point clouds of mine workings. In order to determine sloughage volumes and locations, two sets of laser scans were performed 42 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds. Volumetric changes of 2.3-2.6 m3 were detected on rib faces during the time-lapse study. In addition, displacement in the mine roof was, as expected, not detected, suggesting well surveyed scans and an appropriate scan resolution.

Nov 1, 2013

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By B. C. Lewis

Have technological advancements in underground coal mining driven people's skills to new highs or have the expanded skills of mining people driven the industry's technological advancements. Who knows? What we do know is that both our technology and our people have made meaningful and significant advancements. Overall, longwall systems continue to increase productivity and retreat faster. Globally, gate road development is the primary bottleneck in a longwall mine. The primary bottleneck in gate road development is roofbolting. Generally, roofbolting is the bottleneck in room and pillar operations as well. This paper will present an integrated manufacturer's (Joy Mining Machinery) vision of the future in comparison to current equipment performance. Particular emphasis will be placed on roofbolter technologies.

Jan 1, 1999

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By Arthur D. Silber

The economic success and growth of any metropolitan region depends on mobility. Today, mobility between New Jersey and New York is threatened by a transportation system that cannot meet 21st century travel demands. The transportation bottleneck created by the Hudson River threatens the viability of one of the world?s great centers of commerce and culture. Fortunately, there is a solution: The Access to the Region?s Core Mass Transit Tunnel. The US$8.7-billion Mass Tran-sit Tunnel?s (MTT) new two-track line will double commuter rail capacity under the Hudson and create a new, state-of-the-art cavern station in Midtown Manhattan, with wide platforms, high-speed escalators and other features to improve riders? travel experience. The capacity and other benefits of the MTT project will launch a new era of prosperity for the region, just as the Pennsylvania Railroad did almost 100 years ago when it built the existing two, single-track rail tunnels that now form the sole commuter rail link between New Jersey and New York. The existing tunnels run from North Bergen, NJ, under the Hudson River to Pennsylvania Station at 33rd Street in Manhattan. Construction on the MTT, the largest public works project in the United States, is scheduled to start this year and continue through 2017. The MTT is ready to go to construction thanks to a major commitment of financial, engineering, project management and other resources from NJ TRAN-SIT, New Jersey?s statewide mass transit agency, and the Port Authority of New York and New Jersey, a bistate agency that operates the Holland and Lincoln tunnels, the George Washington Bridge and other major transportation facilities in New York and New Jersey. The project is also strongly supported by the state governments of New York and New Jersey, as well as that of New York City. The MTT is New Jersey Governor Jon Corzine?s number one transportation priority.

Jan 1, 2009

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By G. H. Sedahmed, S. A. Nosier, M. H. Abdel-Aziz, A. A. Mubarak, M. A. El-Naggar, E. G. Abdel-Aziz

The performance of a rotating fixed bed reactor in recovering copper from industrial waste solutions by cementation is studied under various conditions. The rotating fixed bed is made of stacked woven steel screens to take advantage of two features of screens: the ability to present large area per unit volume and their ability to promote high turbulence. Variables studied are initial CuSO4 concentration, bed rotation speed, mesh number of the screens and bed thickness. The presence of baffles was found to increase the rate of cementation. The data were correlated by a dimensionless mass transfer correlation suitable for the design and operation of large scale cementation reactors.