Search Documents

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By Roberto J. Guardia, Tim Shell, Robert A. Robinson, Steve Rodolf

Our aging infrastructure includes numerous tunnels that provide easy access through topographic and societal obstacles. These tunnels are renewable resources that require periodic maintenance and rehabilitation to extend their useful lifespan to hundreds or even thousands of years. However, as with any structural rehabilitation project, tunnel liner rehabilitation requires an inordinate amount of evaluation and care due often poorly documented original construction and subsequent repair construction methods and materials. This paper documents the investigation, planning, design, and construction efforts of the rehabilitation of a 74-year old, 216-meter (713 foot) long two-lane highway tunnel in moderately fractured to highly sheared basalt on the Oregon coast. The tunnel consists of four sections lined originally with timber and subsequently overlaid with concrete, and three unlined sections.

Jan 1, 2005

By B. E. MacNab

During the past several years, Raymond Kaiser Engineers has prepared numerous studies concerning the technical and economic feasibility of coal exporting facilities in the western United States. Perhaps the most striking conclusion to be drawn from these efforts is that many people underestimate the complexity of the highly competitive, dynamic coal marketing system which includes coal loading terminals as an essential but relatively low-cost link in the energy production and delivery chain. The title of this paper, "The Status of Western United States Coal Ports - An Economic Assessment," should not delude anyone into thinking that the future of western U.S. coal- exporting ports has now congealed into a well- defined economic plan. As this paper will demonstrate, the situation is complex and more dynamic than ever and promises to remain so into the late 1980's.

Jan 1, 1982

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By A. Dale Wunderlich

Since Sept. 11, 2001, the author has been asked by several mining companies and mining publications to share some of his insights on how the terrorist attacks on the World Trade Center (WTC) and Pentagon might affect the mining industry globally. Until now, the author has been reluctant to express his thoughts in a publication that could possibly fall into the hands of terrorists and give them some ideas that they may not have been previously considering. However, the author discussed the contents of this article with several friends and acquaintances in the international intelligence community. They said that nothing commented on here is new to the terrorists. Potential terrorist targets Sources within the worldwide intelligence gathering community have told the author that current intelligence data indicates that it is likely that the Islamic fundamentalist groups responsible for the attacks on Sept. 11, 2001will likely be directing their effort at foreign business entities. Any overseas or any domestic businesses of highly visible companies that are part of the anti-terrorism alliance should consider themselves a potential target.

Jan 1, 2002

By G. A. Calboreanu

One way of cost reduction is attained when using materials with improved erosion ? corrosion resistance. For many years hard irons successfully answered the Mining Operation needs however application ranges were limited due to the low chemical resistance of such alloys. Corrosion resistance of any hard iron increases when microscopically homogenizing chromium and generating passivation conditions throughout and between all metallographic phases. Chromium distribution of the new material called Max10 was analyzed with EDS ? energy dispersive spectroscopy. At critical depleted chromium carbide ? matrix interfaces chromium increased to 31.72% which is well within passivation levels. Generally the corrosion resistance of high chromium hard irons provided by Metal Casting Industry is limited to 0.5% sulfuric acid and 28 PPM ionic chlorides. Such restrains increased when using Max10 to 2.0% sulfuric acid and 100 PPM ionic chlorides. Max10 contains 35% carbide volume fraction, has excellent corrosion resistance within pH = 1.15 ? 13.6 while fracture toughness under plain - strain conditions and Mode I opening is KIC = 20 KSI.(inch)1/2. Wear rate was calculated with the pin-on-disk apparatus using a diamond indenter per ASTM G99 recommendation. After years of research, experimentation and implementation the Max10 castings were service installed in slurry pumps and mixing equipment. In some applications the life time of slurry pumps manufactured in Max10 tripled versus previously used materials.

Jan 1, 2012

By Keith Bowers, Frank Mimnagh, Eddie Woods

The CTRL London Tunnels The Channel Tunnel Rail Link (CTRL) London Tunnels comprise 36km of internal diameter bores that were driven by Earth Pressure Balance (EPB) Tunnel Boring Machines (TBMs). The tunnels were constructed between the autumn of 2002 and the spring of 2004. The permanent works also included the 1.1 km long station box at Stratford, five ventilation shafts of depths between 30 and 54 m, 29 cross passages and various large diameter sprayed concrete lined connecting tunnels. The tunnels were driven under densely populated areas of north and east London, as depicted in Figures 1 to 4. Under the parliamentary CTRL Act the project had obligations to make

Jan 1, 2005

By Sadegh Elyasi

TBMand roadheader are two dominating excavation machines in underground tunnelling projects. The performance of these two tunnelling machines has been reviewed and analysed individually by many researchers from multiple points of view. However, there are almost no studies that have made an extensive comparison between these two machines, mostly from financial points of view. The current study is intended to characterize both financial and technical status of these two mechanical tunnelling machines in one of the biggest coal mines in Iran. The main objective of this study is to define the best method and equipment that meets a predefined economic goal, which is mainly to maximize the net present value. To this end, a technical and financial model based on the geomechanical and financial parameters involved in the project has been prepared and the financial part of the project has been carried out by applying COMFAR III financial analysis software. Subsequently, a sensitivity analysis of the model was conducted in order to evaluate the effect of involved parameters on the project. According to the results, a roadheader has better economic justification than a TBM, while the TBM has a better advance rate than the roadheader.

Feb 12, 2021

By H. Dreissen

Upgrading of low-concentration ores is of growing importance today. The Heavy Medium Cyclone Process, thanks to strong centrifugal forces, effectively separates particles varying only slightly in specific gravity but widely in size. The paper discusses the separation efficiency, the method of assessing that efficiency, and the influence of such factors as medium solids. The operating results of nine heavy medium cyclone plants handling following minerals are reported: barite, wolfram, iron, magnesite, diamond, lead-zinc, fluorspar, rocksalt potash. Highlighted are an improved recovery system for heavy medium and some other developments, such as techniques for separation down to 0.1mm and the application in the field of recycling.

Jan 1, 1980

By B. J. Arnold, N. Terblanche

The features of the ‘Turbo’ froth flotation column will be discussed, including the double aeration system that improves flotation yield while not sacrificing grade, the internal launder system, and the unique feed/tailings sump that evens out flow to the flotation column preventing upset conditions. Results from various test programs and installations will be presented.

Jan 1, 2001

The National Institute for Occupational Safety and Health (NIOSH) has continued study of the Personal Dust Monitor (PDM) developed by Rupprecht & Patashnick Co. Inc. through a CDC contract and currently being commercialized by Thermo Fisher Scientific. This report examines the effect of oversize particles, cyclone inversion, and cleaning procedures. Clean and exposed filters were examined using light microscopy and particulates counted before and after various instrument manipulations. The data presented show that the dry cleaning procedures do not cause significant (greater than limit of detection) sample contamination by respirable or oversize particulates and that the cyclone is resistant to particulate carry over during inversion.

Jan 1, 2009

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumedmetabolic rate of 325W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ?Tgi and ?HR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ?Tgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

Nov 8, 2019

By Dongjie Zhang, Zeyu Liu, Shuxin Liu, Yang Liu

Lateral pressure provided by caving rocks plays an important role in keeping the stability of the sidewall rock mass and controlling the rock movement. Taking Xilinhot Fluorite Mine as an engineering background, we studied the control mechanism of the granular media lateral pressure on the rock movement by combining physical experiments, theoretical analysis, and field monitoring. The results indicated that with the increase of the granular media depth, the lateral pressure provided by the static granular media presented two stages of rapid growth and slow growth. The lateral pressure on the footwall was negatively correlated with the dip angle of the orebody, and the lateral pressure on the hanging wall was positively correlated with the dip angle of the orebody. Ore drawing only caused the granular media lateral pressure near the drawing point to decrease. As the granular media moved, the granular media lateral pressure outside the pressure reduction area further increased, and this part of the granular media would play a key role in limiting surface rock movement. On this basis, the improved calculation formula of GLMP was given, which could be better applied to calculate the GLMP and critical granular media column with different dip angles. The action mechanism of the GLMP in the control of the surface rock movement was clarified. The granular body in the collapse pit was mainly composed of three parts: the bottom loose granular media column, the middle compaction granular media column, and the upper critical granular media column. The critical granular media column was the most important area to control surface subsidence and rock movement. Finally, through field practice, after effective filling of the collapse pit, the surface vertical displacement of the hanging wall and footwall was decreased by 56.8% and 55.6%, respectively, and the control effect of surface rock movement was remarkable.

Sep 18, 2023

By D. G. Ball

Other than being used to convey fill material for the gob stowage or building of ribside packs on advancing longwell faces, pneumatic conveying has not been used for the transport of materials on a large scale in mining operations. The technique is extensively used in the wood products industry for conveying wood chips, limestone and other ingredients for the manufacture of paper, for the transfer from railcars, barges or ships to silos or stockpiles and further transfer into the pulp mills. This method of material transfer has the distinct advantage of transporting suitable material over horizontal and vertical distances within the same system. In considering material associated with mining, this includes, ore, coal and rock up to 4 inch cubed size, throughputs of 200 tons per hour over horizontal distances of 3000 feet or vertical lifts of 2000 feet. In recent years tests have been carried out to determine the physical and economic limitations of pneumatic hoisting, the results of which have led to the installation of two fully productive coal hoisting systems at mines of the National Coal Board in Great Britain. The equipment used for the pneumatic hoisting of coal or waste rock is described in this paper, together with a brief history of the tests which led up to the installation of the two hoisting systems in Great Britain.

Jan 1, 1977

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By James Paone

Subsidence movements have damaged houses, schools, streets, and public utility lines in some undermined sections of Belleville and Maryville, Ill. In cooperation with local officials and the State of Illinois, the Interior Department's Bureau of Mines is sharing experience in backfilling abandoned coal mines to demonstrate that bituminous coal mine workings in south-western Illinois can be successfully backfilled and subsidence-prone areas stabilized. Subsurface investigations revealed that mine workings are dry and underlain by underclay deposits susceptible to instability upon wetting. Backfilling will therefore be accomplished by pneumatic injection instead of the hydraulic methods used in previous subsidence-control projects.

Jan 1, 1977

Tunnel damage from explosion and earthquake excitation is correlated with strain and particle motions. Critical strains and motions are then correlated with focal distance, which is so small that permanent strains are highly likely. The shaking process is then numerically modeled to investigate the effects of excitation frequency and joint orientation. The models confirm that near cavern blocks slide intermittently only at relatively high particle velocities during periods of low joint normal stress. Larger displacements occur with relatively small shear wave lengths or relatively high frequencies. Variation in joint orientation and rock mass dilation result in changes in displacement.

Jan 1, 1985

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015