Search Documents

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

By I. K. Craig, F. R. Camisani-Calzolari

Defects which occur at the surface of a continuously cast slab impede the throughput of final product, because an extra stage in the process is required to grind the defects away before further processing can take place. Defect prediction and the minimization of the occurrence of defects is required. The use of two models to define the defect propagation is explained. Both models are derived using system identification techniques such as auto-regression with exogenous input(ARX). One model is used to determine the effect of manipulated variables such as casting speed and measured disturbances such as mould level on temperatures within the mould. The other isused to determine or indicate the effect of the mould temperatures on the occurrence of defects such as transversal cracks. The latter model can be used to predict when the defects will occur and the former can be used to control the occurrence of the defects. Keywords: continuous casting, surface defect, control system, predictor, system identification, ARX

Jan 1, 2003

By H. Askari-Nasab, S. Upadhyay, A. Moradi-Afrapoli

Material handling in surface mines accounts for around 50% of the operational cost. Optimum truck dispatching plays a critical role in the reduction of this operational cost in truck and shovel surface mines. Researchers in this field have presented several mathematical models to solve the truck dispatching problem optimally. However, a critical survey of the literature has shown that three significant drawbacks exist in the available truck dispatching models. The published models underestimate the importance of the interaction between truck fleet, shovel fleet, and the processing plants. They also disregard goals set by strategic-level plans. Moreover, none of the available models account for the uncertainty associated with the input parameters. In this paper we present a new truck dispatching model that covers all of these drawbacks, using a fuzzy linear programming method. The performance of the developed model was evaluated through implementatin in an active surface mining operation. The results show a significant improvement in production and fleet utilization.

Sep 1, 2021

By W. Banda

Paper written on project work carried out in partial fulfilment of Phd. (Process Engineering) degree* The recovery of cobalt and copper from waste slag was studied in a plasma DC-arc furnace in reducing conditions. Three fluxes, CaO,CaF2, and TiO2, were investigated for their influence on selective recovery of cobalt into an iron-rich alloy. A further investigation on the influence of furnace power on the reduction of slag to recover cobalt to the alloy showed that a change in power setting had an unexpected effect on the recovery of metals to the alloy, in that selectivity of base metal recovery over iron recovery decreased at an increased power level. Keywords: DC-furnace, reduction, nonferrous, slags

Jan 1, 2004

By R. J. Fruehan

Slags have many useful functions in iron and steel making. In particular, slags are used to remove impurities such as sulphur, phosphorus and inclusions from the metal, and a large amount of research has been done in this area. Slags also insulate the metal thermally and form reactions with the atmosphere such as reoxidation and nitrogen pick-up. However, slags serve other more unique functions, several of which are reviewed in this paper. The role of slags in new iron smelting processes with regards to reduction of ore and gaseous desulphurization are discussed. In iron smelting processes, much of the reduction occurs by the reaction of carbon in the char and the metal suspended in the slag with iron oxide dissolved in slags. The slags also react with the gas resulting in sulphur removal from the process. The mechanisms of these reactions and pilot plant data for these processes are given in this paper. Slag formation within ferrous burden materials affects the cohesive zone and the performance of the blast furnace. Recent theoretical and experimental findings on this topic are presented. In the electric arc furnace, foamed slags are used to allow for higher power operation and productivity. Of particular interest, foaming in stainless steel production is more difficult than for normal steels. The foam index, or the ability of the slag to foam, for stainless steelmaking is similar to that for carbon steelmaking slags. The poor foaming is due to the lack of gas generation for the foam. Methods to increase foaming in stainless steelmaking are discussed.

Jan 1, 2004

By J. N. Van der Merwe

The data base of failed coal pillars in South Africa was analysed with regard to the time of failure in an effort to develop a method to predict how long after their formation coal pillars will fail. It was found that meaningful results could only be obtained by splitting the data base up into groups that displayed similar behaviour. It was postulated, based on observation and experience, that coal pillars fail by a process of progressive weakening progressing into the pillar from the edges. Minimum pillar dimensions to ensure failure were calculated?these were the dimensions that corresponded to a minimum ?real? factor of safety. From the scaling distance required to reach the minimum safety factor, rates of scaling for the failed pillars were calculated based on the observed real lives of the pillars. It was found that the rates of scaling were unique for different mining areas and that they correlated directly with mining height and inversely with time. Using the derived scaling rates, the predicted pillar lives were back calculated for the pillars in the data base of failed pillars. In two of the three groups, the predicted lives correlated well with the observed lives on a one-to-one comparison. In all cases, the predicted lives were in the same time range as the observed lives. Overall, the frequency of predicted lives closely replicated the observed frequency of observed lives of the pillars in the data base of failed pillars. The method was successful in distinguishing between the data base of failed and a representative sample of intact pillars. While the predictions matched the observed lives of failed pillars, the predictions of expected lives for intact (hitherto unfailed) pillars were orders of magnitude greater. It is now possible to estimate the frequencies of future pillar failures for the purposes of mine closure and undermining of surface structures within broad bands.

Jan 1, 2003

By H. T. Ozkahraman

It is important to know the breakage mechanism in materials since this knowledge influences the results of subsequent grinding operations. There are two distinct failure mechanisms in breakage: one is tensile micro crack generation at low stresses, which leads to macroscopic failure by disintegration, and the other is formation of shear zones under heavier dynamic impact forces, which generates more fines as seen in crush zones in blasting. Tensile fracturing simply breaks the material into fragments. It is seen as the disintegration of the specimen into two or more separate fragments. This happens under the absence of lateral stresses and the material is free to expand. On the other hand, compressive-shear breakage produces finer fragments due to shear stresses. The first mechanism is observed in laboratory tensile and bending strength tests and the second mechanism is observed both in laboratory brittleness tests and in situ blasting operations under dynamic impact forces. The friability of rocks and ores can be determined by a brittleness test. A test apparatus to determine the friability value has been designed to suit limestone strength characteristics used in cement production. The friability and stored strain energy values of barite, marble, limestone and bauxite have been determined and compared with the corresponding Bond work index (Wi) and grindability index (G) of these materials. The physico-mechanical properties of the tested materials have also been determined to investigate their effect on friability and grinding. The relationships obtained between the indices were in surprisingly good agreement, with high correlations (0.99 and 0.97). The Bond work index and grindability index can therefore be estimated from the friability value, which can be determined more rapidly than the Bond test. But for certain rock types such as andesites the relationships does not hold. Key words: comminution, tensile stress, shear forces, brittleness test, strain energy.

Jan 1, 2010

By P. R. Brenchley

Main ore pass systems should last the life of a mine, and too often expensive and hazardous remedial measures are required to repair a damaged ore pass in an attempt to extend its life. In order to maximize the life expectancy of all ore passes at Moab Khotsong, ?wearing blocks? and ?softer support? systems, combined with basic rock engineering principles, have been implemented. Failure of an ore pass can have severe financial implications, both indirectly because the ore pass cannot deliver the broken rock either from level to level or directly in the shaft ore pass system to the required level for tramming to take place, and directly due to the cost of the repair work that is required. Several factors need to betaken into consideration so that production interruptions are eliminated or minimized. Investigations of damaged ore passes at Moab Khotsong and surrounding mines revealed some interesting mechanisms of damage, and some innovative methods of reducing or eliminating the damage have been implemented at Moab Khotsong. The system design was based on 30 years, experience in main shaft rock passes. The design was to counteract scaling, hang-ups and dust problems associated with main rock passes, and the objective was to increase the life of rockpasses. These problems, including the initial design aspects to try and eliminate the repair measures, are discussed in detail.

Jan 1, 2006

By E. Matinde

Human beings have been dependent on metals and alloys for livelihoods since time immemorial. In fact, there is irrefutable evidence that successful ancient civilizations achieved supremacy over their environments through the mastery of metals and alloys (Miller, 1995; Mtetwa, 2022). Over time, metals and alloys have evolved to become ubiquitous engineering materials indispensable to mankind, with applications in industrial and residential infrastructure, agriculture, energy generation and storage, transportation and communication systems, and manufacturing, among others (Elshkaki et al., 2018; Watari et al., 2021). Population growth, technological developments, and increase in urbanization and industrialization are all intricately linked to the intensity of use of metals and alloys. With up to 5 billion people estimated to live in urban areas by 2030 (Armstrong, 2009), the demand for metals and alloys will inevitably increase in order to satisfy the increased demand for infrastructure, machinery, and other human needs (Elshkaki et al., 2018; Watari et al., 2021). According to LePan (2022), urbanization and growth of mega-cities will increase the demand for metals and alloys, such as nickel, steel, aluminium, and copper by 116%, 50%, 57%, and 26%, respectively, between 2019 and 2035. Naturally, the production of metals and alloys from natural ores, secondary resources, and/or a combination of both, to meet this increased demand will invariably lead to the increase in generation of deleterious emissions in the form of wastes. In fact, mining and metallurgical wastes currently constitute the world’s largest anthropogenic streams by mass, often containing a high concentration of elements and compounds that can cause potential damage to natural ecosystems and humans (Hudson-Edwards et al., 2011; Lottermoser, 2011; Matinde et al., 2018; Seetharaman et al., 2022). Obviously, society’s heavy reliance on new mineral resources to drive the emerging energy transition entails that the legacy of these waste streams will continue unabated for the near-foreseeable future. The scarcity of high-grade mineral reserves, coupled with deliberate efforts to solve the anthropogenic circularity conundrum, therefore introduces a high level of urgency in the metal extraction industry to develop nascent and more eco-friendly processes and technologies. Integrating circular economy principles based on intentional configurations of circular industrial ecosystems in order to maintain the value of materials and resources in the economy for as long as possible is widely accepted as a practical approach to mitigating the negative externalities imposed by

Sep 1, 2024

By J. N. Van der Merwe, M. Mathey

"The South African squat coal pillar strength formula, developed by researchers from the Chamber of Mines Research Organization in the 1980s, predicts an exponential increase in coal pillar strength once a critical width-to-height ratio of 5 is exceeded. The arguments that have been proposed in favour of this formula are discussed critically in this paper.Field experience with squat pillars in the USA and evidence from published physical, analytical, and numerical model pillar studies corroborate the fact that a squat effect is unlikely to occur in coal pillars at width-to-height ratios less than 10. Furthermore, an exponential increase in peak strength of coal pillars does not exist. An alternative design criterion for squat pillars in South Africa is therefore suggested. IntroductionFive decades of coal pillar research in South Africa have produced a wealth of information on the mechanisms contributing to the strength and failure of in-situ coal pillars and accompanying phenomena. The relevant knowledge was sourced from, and for, a South African coal mining environment that remained largely unchanged in the second half of the 20th century. The depth of mining seldom exceeded 250 m, with mined seam thicknesses averaging 3 m and typical pillar width-to-height ratios (w/h) of 3–4.It is therefore not surprising that comparatively little research has been directed at the prediction of coal pillar performance in deeper deposits, where squat pillars of larger width-to-height ratios will be required to support the overlying strata. However, a thorough understanding of squat pillar performance will be necessary should the remaining deep coal deposits of the country be extracted in future, for instance in the Waterberg or Ermelo coalfields.A squat coal pillar strength formula has already been proposed in South Africa. The origin of this formula will be discussed in some detail in the following sections and its appropriateness will be critically reviewed against a great amount of evidence from relevant squat coal pillar research conducted internationally."

Jan 1, 2016

The relationship between neural network (NN) performance and the parameters that form the architecture of the neural network is complicated. This paper studies an issue that is still controversial—the effect of the number of neurons and number of hidden layers on NN performance. This paper tests if the above parameters affect network performance when the NN is trained according to the quick stop strategy. It was determined that the number of neurons did not have any effect on the NN performance for a single layer or a double layer network. It was also found that the training error and calibration error could be poor indicators of the prediction correlation coefficient.

Jan 1, 2003

By M. Sanchez, I. Imris, G. Achurra

The Smelting and Converting El Teniente Process for copper concentrates as well as Slag Cleaning Furnace Technologies to treat slags coming out from the El Teniente Furnaces are widely applied today in Chile and around the world. Several industrial applications of this process have shown their capability to treat copper concentrates in a wide range of chemical and mineralogical compositions. Main operational parameters determining performance of the process are: oxygen enriched air flow rate, degree of oxygen enrichment, moisture content of the solid materials processed, molten material levels inside the vessel, frequency of molten materials tapping, bath temperature and copper losses in slags. In this work, the copper losses in the slags from El Teniente pyrometallurgical process are predicted by calculation from thermodynamic data and compared with those determined by microscopic examination and slag industrial data. Results obtained show that the main part of copper losses in the slag from El Teniente Furnace are mechanically entrapped or floated unsettled droplets of the coexisting matte phase. by the contrary the very low copper losses in the slag from slag cleaning furnace are limited by the physico-chemical form.

Jan 1, 2004

By G. van Aswegen

Seismic monitoring became commonplace in the deep South African gold mines in the early 1990’s. The discipline has, to a large extent, developed beyond the ‘research’ stage, and a ‘Guide to Seismic Monitoring in Mines’ has been accepted by the Department of Minerals and Energy1. Although ongoing research is a requirement for the achievement of all the objectives of seismic monitoring in mines, sufficient knowledge exists to apply seismic monitoring for routine seismic hazard assessment as an aid to risk management. The design and management of seismic monitoring systems can be tested against requirements spelled out in the ‘Guide’. Assuming the seismic monitoring system performs as per requirement, the best practice for routine seismic hazard assessment in mines includes • Long term seismic hazard assessment: through back analysis of seismic data and correlation with numerical modelling output, reasonable tests for planned mine designs are possible. • Medium term seismic hazard assessment: o Spatial analysis through contouring of seismic strain related parameters, with superimposed contours or event plots of stress related parameters allow the delineation of potential instabilities in space. o Quantitative and statistical analyses of seismicity in smaller spatial units (usually encompassing production sites) allow the comparative seismic hazard rating of different areas/sites so that rock engineering input and risk management can be optimised • Short term seismic hazard assessment relies mainly on time history analyses of particular seismicity parameters. The temporal patterns are controlled by a combination of temporal and parameter filters, the optimisation of which determines the success rate.

Jan 1, 2003

By M. Magnelöv, Du Sichen, U. Sjöström

An experimental study has been performed to investigate the behaviour and separation of inclusions at the interface between steel and slag. The study has been limited to liquid inclusions because they can be a potential problem in transient situations such as ladle changes in continuous casting of steel. Model experiments with water and silicon oils have been carried out to study the kinetics of separation of simulated inclusions at an interface. The properties of the inclusions and the slags have been varied by using different oils with different viscosities, densities and surface tensions. The effect of temperature of the liquids has also been examined. Measurements of the terminal velocity, rest time and the behaviour of the liquid inclusions at the interface have been recorded using a video camera. It has been found that the inclusions reach their terminal velocity early in the vessel and the experimental velocities differ somewhat from the values evaluated using ?intermediate law?. The results from the experiments have shown that the size of the inclusions has no appreciable influence on the rest time. Droplets of AK50 oil have been found to have considerably long rest time. A water film surrounding the droplet has been expected to be the main reason for the long rest time. The present study has also shown that the viscosity of the oil has certain effect on the rest time, but only to some extent, since viscosity has double functions. A higher viscosity provides higher resistance to the droplet entering the oil phase leading to longer rest time and at the same time damps the lateral movement of the droplet along the interface, leading to easier stabilization and shorter rest time. On the other hand, a high viscosity of the oil phase results in slow dissolution process. It has been concluded that a meaningful model of inclusion separation at the metal-slag interface must take the interfacial phenomena into consideration. Keywords: Inclusions, terminal velocity, rest time, dissolution.

Jan 1, 2004

By M. C. Bekker, T. Govindasamy

The potential benefits of implementing the Last Planner System (LPS) on mining infrastructure projects were explored through two case studies in the South African mining industry. The first part of the study involved measurement of the impact of LPS through earned value techniques on secondary project data. The second part sought to establish the lean construction success factors leading to improvements in construction performance. This was done by means of a research questionnaire distributed to the project owner’s teams, contracted parties, and the LPS facilitators. The results revealed a positive correlation between LPS application and planned percentage complete. However, the performance achieved during the LPS pilot was not sustained. The success factors and benefits considered most evident in the case study pilot differed among the three stakeholder groups. The findings are expected to guide construction stakeholders to better define performance measures and focus on factors required to make LPS implementation more effective in the South African mining sector.

Feb 12, 2024

By C. Nexhip, S. Sun

Critical to understanding and controlling phase mixing and separation in metallurgical processes, is the development of reliable experimental techniques to measure interfacial properties of melt systems. A series of experiments has been carried out to determine the effect of oxygen potential on the surface tension of liquid copper. Using an electromagnetic levitation method, a surface tension-oxygen chemical potential adsorption isotherm was produced for the Cu-O system at T 1400 K. The surface tension results show good agreement with the literature values e.g. within 3 per cent for pure copper. The Belton `ideal' adsorption isotherm was applied, and the following equation derived to best fit the experimental data ? =1251-77.5 1n41+ (2.79x105 . pO1/2)](mN.m Using this equation, the surface tension of copper was calculated/predicted as a function of oxygen potential at 1400 K, and showed excellent agreement with the experimental values. This confirmed that the adsorption behaviour of oxygen in liquid copper is ideal. The saturation coverage of oxygen on the surface of liquid copper was determined to be T0 = 6.65 µmoles.m,-2 corresponding to an area per adsorbed oxygen atom of ao ? 25 Å2. These values agree well with those cited in the literature, and our experimental data cover a very wide range of oxygen potential (10-5 to 10-17 atm). Keywords: levitation melting, surface tension, Cu-O alloys, oxygen potential, adsorption isotherm, surface coverage.

Jan 1, 2004

By M. Bhandari, D. Norval

The bulk of plain carbon steel is produced through conventional Basic Oxygen or Electric Arc Furnace routes where the development of the AC Ladle Furnace has made it possible to also produce alloy steels. Smaller Ladle Furnaces have limitations such as lower efficiency; high electrode consumption and diminutive yields rendering them uneconomical to operate and making the processing of low carbon steel grades difficult due to carbon pick up. The demand for special steels and alloys with strict specifications is increasing while commodity prices remain competitive. The production of special steels and alloys have specific process control requirements and the development of the induction melting furnace (IMF) has made it possible to produce smaller batches economically. Refining and alloying of the melt in the IMF further enhance the efficiency. The INDUREF furnace offers increased productivity and flexibility through increased thermal efficiency and can be utilised for holding molten metal for further processing such as granulating, atomising, nitriding, alloy additions and desulphurisation of Ferro-alloys and steels. The system utilises a specially engineered ladle which is placed in an induction-heating assembly comprised of a stationary water-cooled copper coil and lamination packs. The addition of equipment for vacuum degassing and decarburisation of steels and alloys is also feasible. Benefits are: ? No electrode consumption or carbon pick-up ? Lower installation, operation and maintenance cost. ? No line-flicker facilitates operation on a weak power grid. ? Good power factor and balanced load ? No skull formation and reduced refractory consumption ? Higher yield of Fe-alloys ? Automatic controlled stirring

Jan 1, 2004

By K. Goshtasbi

The mechanical behaviour of schistose sedimentary rocks such as slate show a great amount of anisotropy. Hence, the schistocity plane is essential when investigating the mechanical behaviour of such rocks. The presence of such rocks in civil projects causes non-symmetric deformation and their behaviour is unpredictable. In this research, the anisotropic strength behaviour of slates is studied. Uniaxial and triaxial tests were conducted on specimens having orientation angles (ß) of 0, 30, 45, 60, 75 and 90 degrees. The triaxial tests were done at confining pressures of 3, 5 and 10 MPa. The effect of anisotropy on uniaxial and triaxial strength, cohesion, angle of internal friction and Hoek and Brown's m and s constants were investigated. The results indicate that the strength of slates in uniaxial and triaxial compression exhibit a U-shaped anisotropic behaviour. In-order to evaluate the most suitable criterion for predicting the anisotropic strength of rocks in uniaxial and triaxial compression, an investigation was carried out on various criteria. In uniaxial compression, the Liao and Huong and Ramamurthy criteria had good agreements with the test results. In triaxial compression the Hoek and Brown and Mc Lamore criteria had better agreements with the test results. It should be noted that in-order to utilize these criteria, a large number of tests must be carried out. However, as the Ramamurthy criterion needs fewer test results, it can be the most suitable for investigating the behaviour of anisotropic rocks in triaxial compression. Keywords: Slate, anisotropy, schistose, failure criteria

Jan 1, 2006

By W. S. Steinberg

Keywords: Pyrometallurgy, furnace, open slag bath, Evraz, Highveld In 1963, the full-scale engineering study for the development of an Iron, Steel, and Vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steel works that produced steel and vanadium-bearing slag by using a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for pre-reduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to Open Slag Bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of a higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By R. Boom, K. C. Mills, S. Riaz

This paper details the recent trends in slag-related research from 1999 to 2003. The trends in thefollowing are outlined: • Annual publication rate • Geographical origin of the work • Nature of the research (e.g. thermodynamics, kinetics) • Nature of the slag studied. This study has revealed that slag research in the USA and Europe has decreased to about a half over the last 20 years and that there has been a significant decrease in Japanese research in this area in recent years. However, these decreases have been offset by significant increases in Chinese and Korean research activity. There has been a significant increase in the amount of work carried out on the recycling and environmental aspects of slags in recent years.

Jan 1, 2004