Search Documents

By T. A. Muhlare

The use of electrolyte additives to smoothen cathode deposits during copper deposition is practised worldwide. These additives absorb on the cathode surface and take part in the electrochemical crystallization process. However, these additives also affect the quality of the cathodes when they are inadequately controlled. Electrolyte additives used by Palabora are glue, thiourea, Avitone and chloride. Their effects were determined on cathode quality, the size of the current density region that gives the desired compact morphology, and current efficiency. This was done in a small-scale cell. Small cells have different hydrodynamics from industrial-scale cells, which makes it difficult to simulate the operation of industrial cells in a laboratory. The approach used here was to use a rotating cylinder cathode to attain controlled hydrodynamics. The rotation speed was chosen to give a diffusion layer thickness that is similar to that of an industrial-scale cell. It was shown that even fairly small changes in the additive levels can significantly affect the cathode morphology, and the current density range over which this morphology can be obtained. Keywords Copper, electrorefining, glue, thiourea, avitone and chloride.

Jan 1, 2011

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004

[ ]

Jan 1, 2009

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

By P. C. Schutte

The objective of ergonomics is to enhance the effectiveness and efficiency with which human tasks are carried out. Furthermore, the objective is to improve desirable human values. This can be achieved by enhancing safety, reducing fatigue and stress, increasing comfort, increasing job satisfaction, having greater user acceptance and thereby improving the quality of life. Mechanization has influenced the prevalence of injury, mainly due to the application of human physical effort as the power source. With mechanization, the operator?s function is now essentially one of control rather than being an energy source, however, the risk of injury has not diminished. Mechanization in itself has introduced inefficiencies, health risks and physiological stress. The major objectives of ergonomics are discussed through examples of acceptable and less successful implementation of ergonomics within mechanized mining. The influence of the machine system on the human is addressed and practical solutions to improve and optimize the interaction of the human and the machine are outlined. Furthermore, practical examples of control and display integration, anthropometric and biomechanic influences on design, orientation, posture and stereotypes are used to accentuate the advantages of the application of sound ergonomics principles to the specialized area of mechanized mining.

Jan 1, 2002

An effective electrowinning process in hydrometallurgical industry requires fluoride levels in the base metal solution to be less than 10 mg/l. Selective removal of the fluoride ions from base solution is thus desired, if fluoride was added to control calcium and magnesium in the circuit. Consequently, adsorption of fluoride onto activated alumina was studied in a batch and a column set-up. The effects of base metal solution pH, temperature, initial concentration and flow rate on activated alumina performance were investigated in either a batch or column configuration. A two-level factorial experimental design was implemented in studying column dynamics. Results demonstrate that activated alumina is an effective adsorbent for selective removal of fluoride from base solution. In the batch operation, fluoride was removed to values below the maximum allowable concentration (10 mg/[l]) when pH was = 8. In the column adsorption step at 55°C and 600mg/[l] initial concentration, up to 16 bed volumes were processed before breakthrough level was reached. Desorption step using 1% sodium hydroxide solution achieved an elution of 8 bed volumes. The activated alumina (AA) had a capacity of 8.65 gF/[l]AA at the 10mgF/[l] fluoride breakthrough level during the column adsorption test. Keywords: Fluoride; activated alumina; adsorption; recovery; regeneration.

Jan 1, 2009

By R. Webster

"Daniel Krige’s influence on soil science, and on soil survey in particular, has been profound. From the 1920s onwards soil surveyors made their maps by classifying the soils and drawing boundaries between the classes they recognized. By the 1960s many influential pedologists were convinced that if one knew to which class of soil a site belonged then one would be able to predict the soil’s properties there. At the same time, engineers began to realize that prediction from such maps was essentially a statistical matter and to apply classical sampling theory. Such methods, though sound, proved inefficient because they failed to take account of the spatial dependence within the classes.Matters changed dramatically in the 1970s when soil scientists learned of the work of Daniel Krige and Georges Matheron’s theory of regionalized variables. Statistical pedologists (pedometricians) first linked R.A. Fisher’s analysis of variance to regionalized variables via spatial hierarchical designs to estimate spatial components of variance. They then applied the mainstream geostatistical methods of spatial analysis and kriging to map plant nutrients, trace elements, pollutants, salt, and agricultural pests in soil, which has led to advances in modern precision agriculture. They were among the first Earth scientists to use nonlinear statistical estimation for modelling variograms and to make the programmed algorithms publicly available. More recently, pedometricians have turned to likelihood methods, specifically residual maximum likelihood (REML), to combine fixed effects, such as trend and external variables, with spatially correlated variables in linear mixed models for spatial prediction. They have also explored non stationary variances with wavelets and by spectral tempering, although it is not clear how the results should be used for prediction. This paper illustrates the most significant advances, with results from research projects."

Jan 1, 2015

By H. Hurkchand

Background: A cross-sectional study was conducted in November2001 to establish the prevalence rates of Human Immunodeficiency Virus (HIV) and sexually transmitted infections (STIs) (Chlamydia trachomatis and Neisseria gonorrhoea) in a coalmining town in Mpumalanga. Methods: 155 adults were recruited (79 males and 76 females), by holding community meetings, and by door-to-door recruitment. Saliva and urine specimens were collected for the analysis of HIV and STI prevalence, respectively. Results: The mean age for males was 31.35 years (min = 19 yrs and max = 50 yrs) and the mean age of the female participants was31.90 years (min = 17 yrs, max = 49 yrs). The prevalence of HIV was found to be 22.78% [95% CI (14.09?33.59)] in the males vs. 47.37%[95% CI (35.79?55.16)] in the females, [p = 0.001, OR = 3.05, 95%CI(1.49?6.26)]. The prevalence of C. trachomatis was 7.90% [95% CI(2.95?16.39)] in the males vs. 12.86% [95% CI (6.05?23.00)] in the females, p = 0.324. The prevalence of N. gonorrhoea was 3.79%[95% CI (0.79?1.08)] in the males vs. 9.86% [95% CI (4.06?19.26)]in the females, p = 0.137. HIV was significantly associated with C. trachomatis, [p = 0.032, OR = 3.18, 95% CI (1.04?9.72)], but was not significant when stratified by gender. HIV was not significantly associated with N. gonorrhoea (p = 0.072) but it was significantly associated when stratified by gender, p = 0.001 for females. There were no significant associations between HIV and age (p = 0.408), even upon stratification by gender. Conclusions: HIV prevalence in this community is high, and corresponds to national figures. However, the prevalence of STIs is surprisingly low as it would be expected to be high in a migrant population. Although communities are exposed to expanding peer-education activities that encourage behaviour change, the prevalence of HIV in this group. There is an urgent need for interventions designed to treat or prevent HIV infection in women generally and in women at high risk. Keywords: HIV prevalence, STI prevalence, antenatal, mining

Jan 1, 2005

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By D. Schreuder

Conditions in the South African market relating to atmospheric emission control has changed dramatically over the last 10 years. Companies have become more responsible, environmentally aware, and have to comply to more stringent environmental limits set by legislation. This paper describes briefly the current best available atmospheric pollution abatement technologies relating to particulates, acid gases, NOx, acid mists, aerosols, mercury, dioxins and furans. Mention is also made as to the best practices for product work-up and waste product disposal.

Jan 1, 2006

By A. S. Macfarlane

The introduction of new technology into mining operations is seen as a strategic necessity by many mining companies, in order to improve safety and to improve operational effectiveness. Many attempts have been made in recent years to introduce new technologies into mining operations in southern Africa. Amongst these are noteworthy successes, as well as some disappointing failures. Often, the reason for failure does not lie with the technology itself, but with the work system into which the technology is introduced. Such failures may come with a significant opportunity cost, and have a detrimental effect on future development, simply because the system has not been adequately engineered, and the risks have not been adequately assessed and managed. This paper examines the reasons for such failures, and proposes a methodology to be followed to ensure successful and sustainable implementation of new technologies, such as to reduce technical and financial risk to the company, and to energize the workforce into ensuring the initial objectives of the project are met. The paper also focuses on the application of appropriate technology, and the development of technological applications which are commensurate with the level of development of the work environment into which it is introduced. The paper therefore focuses on the application of risk management, change management, systems engineering and feasibility analysis as being key elements of a successful and holistic technology implementation programme.

Jan 1, 2001

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By K. Woodward

"SynopsisSeismically active mines generally experience an increase in seismic hazard due to rock mass instability following blasting. Re-entry protocols commonly include measures to limit the spatial and temporal exposure of personnel to increased seismic hazard induced by blasting. The management of periods of increased seismic hazard requires the development of re-entry protocols for a unique mining environment. Identifying mining conditions that may result in significant seismicity following blasting relies on retrospective analysis, which is often focused on seismicity occurring within a certain period after blasting and within a certain radius of the blast in the broader context of site-specific experience.The analysis of seismicity without considering blasting times and locations allows for the relationship between seismicity and blasting to be investigated without prior assumptions concerning dependency. To achieve independent analysis, seismicity that is clustered in space and time (referred to as a seismic sequence) must be identified by assessment utilizing only seismic parameters. An automated algorithm is implemented that assesses the timing, location, and quantity of seismicity to identify seismic sequences, represented by the time of the first event and mean location of all events in the sequence.The relationship between sequences and blasts is assessed by calculating the distance and time from each sequence to the closest blast in space and time. Establishing an independent classification between sequences and blasting provides insight into the unique cases where seismic sequences are remote and/or delayed with respect to blasts and identifies cases when sequences exhibit a weak relation to blasting. The nature of seismic responses to blasting has direct implications for the management of the increased seismic hazard associated with seismic sequences.The approach presented in this study contributes to the management of seismic hazard by providing empirical support for the relationship between seismic sequences and blasting. These relationships indicate the portions of sequences that can and cannot be practically managed using tactical approaches. Furthermore, the analysis of sequences reveals the nature and evolution of rock mass responses to blasting. These results have implications for the extent of spatial or temporal re-entry restrictions required for the optimal management of time-dependent rock mass response to mining."

Jan 1, 2015

By M. Z. Naghadehi, E. Emami, J. Sattarvand, R. Battulwar

In this paper, a methodology for a computerised recognition of joint sets on 3D point cloud models of rock masses is presented. The process starts with classifying joints on a 3D rock mass surface through training a deep network architecture and validated using manually labeled datasets. Then, individual joint surfaces are identified using the Density-Based Scan with Noise (DBSCAN) clustering algorithm. Subsequently, the orientations of the identified joint surfaces are computed by fitting least-square planes using the Random Sample Consensus (RANSAC). Finally, the joint planes are classified into different joint sets, and the dip direction and dip angle for each set are calculated. The performance of the proposed methodology has been evaluated using a case study. The results show that the presented procedure is fast, accurate, and robust.

Sep 1, 2021

By J. -C. Trickett

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2 Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological models even further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip. Keywords: 3-D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; seismic micro technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2005

By J. Janssens, B. Coletti, S. Smets, J. Plessers

The oxygen activity of the ladle slag determines the reactivity towards the steel during ladle treatment. Therefore, the in situ measurement of the oxygen activity of slags can be an important tool. The applicability of an electrochemical sensor is examined in this work. The sensor measures the electromotive force (EMF) that is established between a sample of the slag phase that is immersed in the liquid steel bath and a reference system (Cr/Cr2O3). Industrial and laboratory experiments demonstrated the capability of the sensor to detect the influence of the slag components on the measured oxygen potential. Comparison of the measured values with thermodynamically calculated values shows that the measured oxygen activity is systematically too low. This was attributed to a reaction of the steel with the slag sample. To investigate this, further lab tests were performed where the slag oxygen activity was measured after the slag had been equilibrated with the steel. The measured values were dependent on the oxygen activity (aO) of the steel. For industrial applications, it is concluded that the aO of the steel should be known and that this value is necessary for the interpretation of the measured values. Keywords: low carbon steels slags, slag oxygen activity, on-line sensing, thermodynamic evaluation.

Jan 1, 2004

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

By M. B. C. Brandt

Focal depths of 15 tectonic earthquakes and 9 mine-related events were determined for South Africa using data recorded by the South African National Seismograph Network. These earthquakes and events were relocated by means of the Hypocenter program using direct P-waves (Pg) , critically refracted P-waves (Pn) , and first-arrival S-waves for the magnitude range 3.6 ?? ML ?? 4.4. Focal depths were first determined by means of the minimum root mean square (RMS) of the differences between the measured travel times and those predicted using the velocity model. The depths for tectonic earthquakes had a 2 km ?? D ?? 10 km range and an average depth and standard deviation of 6.9 ± 2.3 km. Depths for minerelated events ranged over 0 km ?? D ?? 7 km, averaging 3 ± 2.3 km. Next, arrival times for the additional regional depth phases sPn , PmP, sPmP, and SmP were measured. Focal depths were re-determined for the relocated epicentres, with the minimum variance (i.e. spread) of the differences between the measured travel times and travel times predicted by means of the Wentzel, Kramer, Brillouin, and Jeffreys (WKBJ) method for synthetic waveform modelling. Depth ranges were 4 km ?? D ?? 7 km (average 5.9 ± 1.2 km) and 1 km ?? D ?? 4 km (average 2.4 ± 1.2 km) for tectonic and mine-related events, respectively. The derived depths were verified for one tectonic earthquake with synthetic-to-recorded-waveform fits using the WKBJ synthetic seismogram software for the abovementioned regional phases. The focal mechanism parameters for this earthquake source were obtained from the National Earthquake Information Centre. Focal depths were estimated for nine stations by visually comparing synthetic waveform phases with recorded waveforms, ranging from 5 km to 8 km.

Jan 1, 2014