Search Documents

By S. Nana, M. B. Cortie

Duplex stainless steels containing high levels of manganese and copper and lower-than-normal levels of nickel were produced and evaluated. The experimental alloys containing 3 per cent copper by mass could not be successfully hot-rolled. Alloys containing less than 2 per cent copper could be hot- and cold-rolled without difficulty. The wrought experimental alloys that contained copper were found to offer some advantages over the 2205- type duplex stainless steel in sulphuric acid at 52°C. Resistance to pitting attack was governed primarily by the chromium, molybdenum, and nitrogen contents, and one of the experimental alloys was superior to the 2205-type alloy in the ferric chloride test. It is concluded that manganese is a useful substitute for nickel in duplex alloys, but that further work is required before the present alloys, or variations of them, could be commercially viable.

Jan 1, 1993

By P. Harris, N. Heywood

An existing 1 800 m long pipeline, which carried waste mica slurry from kaolin processing, is to be recommissioned. The mica solids throughput is to be substantially increased from 5.2 t/h up to a maximum of9.53 t/h, but with a typical throughput of around 7.5 t/h. Because of this throughput increase, it was unclear whether the existing 80 mm diameter pipe would be adequate. In addition, the pipe route is to be extended by 250 m to 2 050m, and its elevation at discharge to settling lagoons increased from 66.2 m to 80 m. The pipeline hydraulics of waste mica slurry were investigated for the 80 mm diameter pipe using the Saskatchewan Research Council?s (SRC) Two-Layer Flow Model, for the maximum mica solids throughput of 9.53t/h. The pipe operating velocity was compared with the predicted deposit velocity for several mica concentrations, ranging from 20% to 50% by weight. Estimates were made of the total differential pressure across the proposed2 050 m long pipeline, as well as the power imparted to the slurry by the pump, and the specific energy consumption (SEC). Two pipe diameters were assumed: 80 mm when no mica wall deposit is present, and 70 mm when there is a 5mm mica wall deposit. This parameter has a significant effect on the determination of the appropriate pipe operating conditions. For the pipe operating velocity to remain adequately above the deposit velocity (and therefore for the heterogeneous flow pattern to prevail in either horizontal or inclined pipe), it was concluded that if the newly commissioned pipeline contains no mica wall deposit, the pipe should initially be operated at a mica concentration of between 20% and 25% by weight, probably with a target mica concentration of about 23%. A 23% mica

Jan 1, 2007

When a mine decides to construct surface structures close to, or on undermined ground, it is required in terms of the regulations of the Mine Health and Safety Act to obtain permission from the Department of Minerals and Energy (DME). Apart from the legal requirements, the stability of the structures is crucial as damage to the structures due to surface movements could result in loss in life, equipment and/or production. This paper deals with the rock engineering aspects of a study that was conducted on one of the chrome mines in the Bushveld Complex (BC) involving the construction of plant structures on shallow undermined ground. The paper addresses the legal requirements and guidelines regarding ground stability of surface structures placed on undermined ground and the assessment of the undermined area with regard to the following: ?sources of potentially damaging surface movements ?safe mining spans ?stability of the pillars ?effect of the loading of plant structures on underground stability. Due to the irregular layout and geometry of the pillars in conjunction with a changing surface topography, numerical analysis and not the conventional tributary area theory was used to determine the imposed loads on the pillars. In order to subject the plant structures to minimum movement, the plant should be located in areas where the pillars would remain stable, the elastic deformation of the hanging wall is minimized and hanging wall failure extending to surface is unlikely to occur. The study indicates that although the depth of undermining is shallow (between 27 m and 60 m), potential damaging surface movements are not anticipated due to the stability of the pillars, competent nature of the overlying strata and negligible effect of the plant structure loading on the underground stability.

Jan 1, 2004

By J. H. French, O. E. Lissner

S. J. Venning (Member): The authors should be congratulated on producing such concise data from the plethora of experimental report results. Their observations on the cost of liners calls for some comment however, as the really unique feature about liners in South Africa is that they can be obtained so cheaply. Attention has been focussed on the 1961 cost of white iron at R50 per ton for chill cast block liners while manganese steel liners are reported as costing as much as R250 per ton. The former are however, a relatively heavy, simple casting with a low labour content and reasonably high percentage productivity, made from metal melted in a cupola. The capital investment to produce this type of casting is low compared with that required to produce manganese or other alloy steels. The chill cast liner block is always a production item and is cast in a permanent mould. Almost all manganese mill liners, except perhaps small aperture screens, are sold for considerably less than the R250 per ton quoted by the authors. Where a price of this nature is asked it would be because the design of the casting demanded is complicated or leaves little metal to carry the labour and other costs of production. As reference has also been made in the paper to liner costs in America, prices for similar types of liners obtained during a visit to Canada and the U.S.A. in 1961, could be of interest: Material Price per Location short ton Ni-hard R250 Elliot Lake Body liners block type Ni-Hard R300-310 FAS New York Mn Steel R280-290 FAS New York Screens (grids) slotted Cr.Mo. Steel R600 FAS New York hole Ni-Hard R320 Elliot Lake At this time the price of comparable manganese steel block type liners on the Witwatersrand was between R145/R155 per short ton. White iron in Canada was then quoted at about R150 per ton, but as Ni-Hard gave a life of at least two to twoand-a-half times that of white iron, it was a much more attractive proposition particularly when relining and down time costs were taken into consideration. There is little doubt that most foundries would welcome clear and complete specifications of the customers requirements and systematic checks to ensure that these specifications are being met. B.S.S. or other accepted standards should form the basis of these, and periodic inspections should be undertaken to ensure that only those foundries capable of complying should be included as suppliers. The authors have referred to new designs, but can the industry really call the grid and plate new when the patents were taken out during the second world war and the sawtooth block has been used for at least 35 years. Unfortunately, far too little thought and consideration are normally given to the ultimate mill liner design while the mills themselves are on the drawing boards. The position and size of the door opening, which is the key to the ultimate shell liner configuration, the drilling of the

Jan 9, 1968

Duties: The successful applicant will be responsible to the Planning Superintendent for long and short term Mine Planning. The current expansion programme requires production to be derived from new mines, using the most modern equipment. Considerable forward planning is required. Qualifications: Applicants should possess a degree or diploma in Mining Engineering. Experience: Five to eight years' experience in hard rock mining is required of which some part has been spent on mine planning. Conditions: Salary to $7,000. Ample opportunity for further promotion exists in this expanding organisation. The person appointed will be eligible for benefits including discretionary annual staff bonus. An executive home will be provided in the new township with services at nominal rates. Primary schooling is available at Kambalda and the bus service operates for post primary students attending schools at Kalgoorlie. Reasonable relocation expenses within Australia will be met by the Corporation. Employment is conditional upon passing the necessary medical examination for admission to the Western Australian Mining Industry. Written applications, which will be treated in strict confidence, stating nationality, age, marital status and setting out qualifications and experience should be addressed to: The General Manager Operations-W.A., Western Mining Corporation Limited, Post Office Box 80, BELMONT, W.A., 6104. The envelope and application to be marked- "Attention: Senior Mining Engineer".

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different methods of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approaches. This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different method. of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approachs This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

By M. Splaine, C. E. Dohm, S. J. Browner

As the grade of the gold (head grade) in the ore supplied to a reduction plants falls, the efficiency of recovery of the metal drops. This is not simply due to a fixed grade lost in the residue, since the residue grade is itself a function of the head grade. A multi-disciplinary approach was used in the construction of a model to represent the relationship between head grade and recovery efficiency. The model is a physicochemical one based on (i) the reaction characteristics of cyanidation, (ii) the milled-ore selection characteristics of gravity concentration, and (iii) the nearly log normal distribution of gold grades and particle sizes in ore reserves. The model was used to set sound target levels for recovery efficiency for a given head grade at a given plant, against which the performances of the plant equipment can be judged for control purposes.

Jan 1, 1982

By J. D. Flint

A description is given of the extraction of pillars in a seam of coal which normally varies in thickness from 10 feet to 14 feet using conventional trackless mechanised units. By using the pocket and fender method of pillar extraction, the high capital cost of hydraulic supports is eliminated, and a volumetric extraction of 85% to 90% of the seam of coal is possible. This method of mining opens up the possibility of extracting vast tonnages of coal which hitherto would have been left in situ as pillars. The major benefits likely to accrue from this technique are seen as follows: 1. Greater volumetric extraction of the seam; 2. Longer panel life with less frequent transferring of sections; 3. Preservation of our natural resources. The authors deal with the history of this development at Springfield Colliery, discuss the present results and outline the future trends in the light of current experience.

By R. H. Steel

Ingot casting and wire drawing In Iron Age Southern Africa by R. H. STEEL (Visitor) This paper describes the experiments that were conducted in 1974/1975 on two related aspects of Iron Age copper technology in Southern Africa: ingot casting and wire drawing. Three types of ingot were successfully cast: the St Andrew's Cross ingot, the marale ingot, and the musuku. It is suggested that the 'studs' on the musuku are not the remains of broken-off rods as previously proposed by other investigators, but that the ridged pattern is an ornamental feature. Copper wire was successfully drawn with similar tools and according to the procedures described in the literature on African Iron Age wire drawing. It is concluded that these accounts are generally accurate and that the pre-European metal workers are worthy of respect for the results they achieved with primitive methods.

Jan 11, 1975

By D. F. Malan

This study Investigates transient closure piles of tabular excavations. Measured closure profiles in stopes indicate that time-dependent acts f the rockmass can be very prominent but such effects have been largely neglected in past analyses and modelling. This was due to a poor understanding of the time-dependent mechanisms controlling closure rates This paper investigates the feas-ibility of representing the rockmass as a visco-elastic medium. Currently, no analytical solution for the viscoelastic convergence of a tabular stope is available in the literature. Therefore, the author derived a solution using the correspondence principle and a known elastic solution. It is assumed that the rockmass behaves elastically in hydrostatic compression and as a Kelvin substance in distortion A parametric study is Included to aid in the calibration of the model parameters, together with a discussion on the correct calibration of these parameters from experimental data.

Jan 1, 1995

By J. C. Coetzee

In this article, a case is made for the importance of the transfer and management of tacit knowledge to ensure continued sustainable competitive advantage within the pyrometallurgical industry in South Africa. The state of knowledge management (KM) is assessed through a theoretical and empirical study. The empirical part of the study was conducted by means of a survey questionnaire. An important prerequisite within the research entailed determining the current state of KM within the pyrometallurgical industry, and the findings are presented throughout this article. The research argues for initiatives to address the high turnover of pyrometallurgical knowledge workers. This industry needs to entrench tacit knowledge and therefore address the problems associated with the continuous loss of inherent specialized knowledge. Appropriately, emphasis is placed on identifying initiatives required to embed and retain not only human capital lost through mobility, but rather retaining tacit knowledge through a practical KM framework.

Jan 1, 2012

By J. C. Coetzee

In this article, a case is made for the importance of the transfer and management of tacit knowledge to ensure continued sustainable competitive advantage within the pyrometallurgical industry in South Africa. The state of knowledge management (KM) is assessed through a theoretical and empirical study. The empirical part of the study was conducted by means of a survey questionnaire. An important prerequisite within the research entailed determining the current state of KM within the pyrometallurgical industry, and the findings are presented throughout this article. The research argues for initiatives to address the high turnover of pyrometallurgical knowledge workers. This industry needs to entrench tacit knowledge and therefore address the problems associated with the continuous loss of inherent specialized knowledge. Appropriately, emphasis is placed on identifying initiatives required to embed and retain not only human capital lost through mobility, but rather retaining tacit knowledge through a practical KM framework.

Jan 1, 2012

It is perhaps somewhat unusual for a contributor to comment on the authors' reply to his critique. However, I should like to return to a specific comment made by the authors. Award to Bob Laburn The Federation of Societies of Professional Engineers (FSPE) is pleased to announce that the 1984 FSPE Award for Services to the Engineering Profession was presented to Dr R. J. (Bob) Laburn at a function held on 14th February, 1984.

Jan 1, 1984

A theory is presented providing a concise mathematical description of the performance of a percussive rockdrill in terms of its principal mechanical dimensions. The theory defines the relationships between the values of thrust required to produce optimum rates of penetration at different throttle air pressures in terms of the piston areas and derives an equation for the prediction of these rates. An analysis of drillsteel life and bit wear is also made.

By F. van Heerden

The paper sketches the. management of the various phases in a cost-reimbursable, plus-fee contract. which is claimed to be the most flexible of all contracts. In this type of contract, the contractor is reimbursed for all the direct costs Incurred, plus a percentage fee to cover his profit (or overheads and profit). The client usually reserves the right to approve all drawings, equipment purchases. contract awards, technical specifications. project cheques and change orders.

Jan 1, 1982

By E. Rex, T. J. Goff, W. S. B. van Beek, P. E. Nel

"The PGM smelting industry is known for operating at significant high superheats. Both the slag and matte phases that separate via gravity need to be tapped out of the furnace in a safe and efficient manner, which can be achieved only through sound tap-hole management practices. This paper gives an overview of the tap-hole management approach followed in the operations at Lonmin’s Western Platinum Smelter.Five circular AC furnaces are operated, with each furnace comprising essentially a crucible and auxiliary equipment. Within the crucible, slag and matte tap-holes are situated at different elevations. The slag phase is tapped at a higher elevation than the matte phase. At the three older furnaces, tapping is done by the conventional method of lancing open the tap-hole and closing it with a dolly. However, at the two newer furnaces, tap-holes are opened and closed with the aid of a drill and mudgun.Tap-hole management can be divided in a number of aspects. In order to achieve a safe opening and closure every time, Lonmin distinguishes between three important aspects - the design of the tap-hole system, the operating practices followed, as well as care and maintenance. This paper briefly describes the tapping channel and cooling requirements for handling superheated matte, together with the difference in design of the matte and slag tap-holes. Mention is also made of the importance of auxiliary equipment, which includes the launders, fume extraction, granulation water, and mudgun and drill units. Improvements made to the matte tapblock design are discussed.The monitoring, alarm, and safety systems related to matte and slag tapping are described. Tap-hole life and different wear mechanisms are mentioned. Tapping can be done safely only if the tap-holes and equipment are maintained properly. Mention is made of the tap-hole refractory repair practices, and the improvements made in order to reduce repair time as well as to extend the time between deep repairs. The importance of the correct tap-hole clay selection in order to nurse the tapping channel after each tap is also discussed.The paper finally touches on some research and development work that was done in order to improve the monitoring of the condition of the tapblock by means of fibre optic temperature sensors"

Jan 1, 2014

By G. A. Wiebols, N. G. W. Cook, N. C. Joughin

Discussion R. E. Rarnes (Member): The original concepts and the pioneering work now brought to the practical test stage by the Mining Research Laboratory team deserve our highest praise. The authors of this comprehensive paper rightly stress the urgency of establishing the extent to which the apparent potential can profitably be realised in practice. It is to be hoped that adequate funds will be made available by individual mining companies, the Chamber of Mines and manufacturers to attract the necessary staff and maintain the high rate of achievement of the last two years. From the Seventy-Eighth Annual Report of the Chamber of Mines and its members we see that, in 1967, with a Working Revenue of R759.8 million from gold and R54.6 million pit mouth coal sales and with profits from gold and uranium and pyrite of R307.9 million, only R1.9 million was spent by the Chamber on all forms of Research. It is considered unlikely that the associated mining companies and manufacturers exceeded this investment expenditure. Assuming a total of R4 million spent by the industry on Research and Development, this is less than half of 1 per cent of sales of gold and coal. This percentage, so low in comparison to North America and Europe, is no worse than that of Exploration expenditure which, in 1967, with South Africa's total mineral production of R1,287 million, was estimated to have been R6 million (Pretorius 1968). In a primary industry with ever present depletion of ore deposits and with cost escalation, expenditure on Exploration and on Research and Development is not a risky luxury but a tactical obligation. The potential rate of return on research expenditure into rock breaking is high. Stores consumed by gold and coal mines, members of the Chamber of Mines, totalled R316.2 million in 1967. Except for purchased power costing R42.2 million the highest cost group was explosives, drills and drill steel totalling R33.8 million or 10.7 per cent of the total stores consumed. In the paper under discussion it is claimed that the low 'effective stoping width' should greatly reduce the likelihood of rock falls or rock bursts to the extent that permanent support can be dispensed with. Insofar as this narrow cut is only 12 in. in advance of the working area which, with a 10 in. channel, is unlikely to be much reduced in width from that achieved by current methods, this claim is not readily understandable. Were it to have been based upon the regional support gained from packed waste it would have been more acceptable. Pre-developed stope drives may give serious trouble at depth and for this reason it is questioned whether a stoping area can avoid periodic sub-development blasting-the spoil and fumes from which will interfere with the rock flow and continuous mining of the rock-cutter. If, in the mining method proposed by the authors, stope drives are cut as small as possible (6 ft by 6 ft) then 25 per cent of the total tons handled (excluding resued waste) and 5 per cent of the gold will be blasted conventionally in the stope. At this stage one cannot envisage tunnelling machines economically or practically capable of such work. The various methods described by the authors and subsequent contributors for breaking waste are most interesting. It was noted that the 'bull wedge' and 'explosives' in Fig. 1 of the paper were no further from the ideal point 'A' than was 'cutting'. The writer considers that the bold and imaginative steps taken by the Mining Research Laboratory Team, the mining companies and the manufacturers concerned will eventually lead to a successful rock cutting machine with universal application largely independent of rock type. This may take many years. In the meantime other methods of improving productivity of saleable metal by rock breaking teams should be investigated even if such methods have local applications only. In 1955 the writer conducted tests with a wire saw similar to those used in quarries in the Northern Transvaal and elsewhere. Jeppestown shale, the immediate footwall of much of the East Rand gold field, was cut at the rate of 6 in. per hour using sand, water and a special endless rope driven by a low h.p. motor. A hypothesis on its application was submitted to the Office of the Government Mining Engineer in 1955 and to other mining institutions in 1966 after the writer returned to South Africa. By inference, rope sawing was classed as less promising than other methods tested in the Orange Free State Goldfields (Parker 1969). With highly resilicified hanging and footwall quartzites this was not surprising and confirmed the writers findings when testing hanging wall quartzite from the East Rand in 1955. The relatively uniform conditions, the low strength, hardness, and silica content of the Merensky Reef platinum deposits (Gray and von Bardeleben 1969) and in particular, the existence of overlying Merensky pyroxenite (Cousins 1964) make this and the East Rand attractive areas for larger scale testing of wire saws. It is envisaged that in suitable rock types the 5/8 in. slot would be advanced down dip or down a minor dip. In undisturbed areas 'faces' of up to 200 ft in length could be cut several feet in advance of breaking which could then consist of light blasting to the second free face or some of the methods now being tested for breaking waste in rock-cutting operations. A wire saw is an inexpensive and simple machine which, in some areas, could make significant and early gains in rock breaking efficiency as well as in ground and stoping width control.

Jan 5, 1968

Contribution by J.S. Kuijpers* Kirsten's paper discusses the potential for seismic activity on faults in relation to depth, span, stope support, and discontinuity strength, and puts forward some explicit conclusions. Quoting from the author, the main conclusions are as follows, together with my comments. Author's reply The author gratefully acknowledges the contribution to his paper. It provides further elucidation to the very complex problem of quantifying the effects of mining-induced seismicity. The mechanical behaviour of rock under seismic excitation has been sadly neglected over the past twenty years, during which attention was almost exclusively focused on the study of the spatial location of seismic events. It is to be lamented that, on the eve of South Africa's movement to significantly greater depths of mining, so little quantities information is known about the mechanical effects of seismicity. It is a challenge at this stage to make up for this lapse in knowledge in the shortest possible time.

Jan 1, 1994

By N. B. Strydom

Die bedryfsfisioloog en lugbesoedeling N. B. STRYDOM, Ph.D. (Phys.) (Illinois) (Genoot) Although the industrial physiologist can still be regarded as a rarity in South African industry, it is obvious that he could make a positive contribution to the control of air pollution. For the past twenty-two years, the gold-mining industry has invoked the aid of industrial physiologists in solving various problems that continually crop up in the more effective and safer utilization of man-power. Air pollution is only one facet that has received attention. It can be stated emphatically that other industries could gain many advantages from the employment of this type of specialist. Because of inadequate opportunities for academic training, however, the industrial physiologists available might not be enough to fill all the possible posts in industry at present, but confidence is expressed that interested persons will soon be able to follow a full university course in this field of study.