Search Documents

By A. Hinde, M. H. Moys

Tailings from metallurgical plants, when deslimed with hydrocyclones, provide a valuable source of material for the backfilling of mines. The effectiveness of this material as a support medium is a sensitive function of its particle- size distribution and water content. It is therefore important that the hydrocyclone-classification plants used to prepare the backfill are operated efficiently, and that the effects of feed disturbances on the composition of the backfil are minimized. This paper addresses the problem of the design, control, and optimization of classification plants to satisfy this need. The development of a computer program to simulate the dynamic behaviour of a hydrocyclone circuit of any given configuration is described. The use of the simulator to investigate the relative performance of conventional and innovative control strategies for single-stage and two-stage circuits is discussed in depth. The results of simulation studies are presented that indicate there is considerable scope for improving the performance and cost-effectiveness of backfill-classification plants.

Jan 1, 1991

In the investigation described here, it was found that the main effect of temperature is on the rate of flotation, and that adsorption of the reagent is not rate controlling. Above 10°C, the flotation rate of pyrite and gangue increases almost exponentially with a rise in temperature. Below that temperature, the flotation rate of pyrite shows a sudden marked decrease, that of gangue increases, and the sulphur grades are significantly poorer. In the flotation of pyrite, the mass transfer of the pyrite from the pulp to the troth is thought to be the ratecontrolling step, whereas the flotation of gangue is controlled by the combined effect of the stability and velocity of the froth and the viscosity of the elutriating medium. The latter is probably the controlling effect at temperatures below 10°C. Little difference was noted in the recoveries (provided no time limit was set) with changes in temperature; hence adequate recoveries can be obtained at Iow temperatures by the introduction of longer residence times for the pulp. The adverse effects of Iow temperatures on grades can be overcome only by additional cleaning or by heating of the pulp.

Jan 1, 1984

By N. Graham, C. Walker

The SORD Miner is a patented mining principle being developed to exploit mineral and energy resources that current technology can not access. SORD Miner is designed to operate in underground wet, granular, continuously collapsing geological environments such as alluvial and marine deposits. It is somewhat like a cutter suction dredge and should be capable of mining its way through any fine granular material like sand or gravel, pumping the slurry back to the surface. In areas where the target layer is covered, the SORD Miner is inserted below the water table and will tunnel its way to the mineral deposits at depth. This paper describes the development, concept testing and prototype construction of the SORD Miner.

Jan 1, 2007

By L. E. Kun, R. O. Oelofsen, E. J. J. van Vuuren

High-rate floc-blanket clarification of gold pregnant rotary filtrate was introduced at the Vaal Reefs South gold plant of the Anglo American Corporation during February 1978. A. daily 12 000 to 15 000 t of filtrate, with an average suspended-solids concentration of 350 mg/I, is continuously clarified to a concentration of less than 2S mg/I of suspended solids in a modified plant pachuca (10 m in diameter) at throughput rates of 7,7 to 8,5 ma/m2.h by the addition of 5 g/t of ferric chloride inorganic coagulant and 0,2 g/t of Superfloc NI00 flocculant. The pachuca overflow is then clarified further in seven Stellar candle pressure filters of 54,S m2 surface area to under 5 mg/I of suspended solids. The combined clarification cost when the hopper clarifier is used in conjunction with the Stellar filters is R0,0032 per ton of liquid treated, which is approximately 60 per cent lower than the cost of Stellar filtration on its own. The savings are mainly due to the reduced use of filter pre-coat, the consumption of which has dropped by 70 per cent since the introduction of hopper clarification.

Jan 1, 1979

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By J. F. Morrison, C. H. Wyndham, N. B. Strydom

INTRODUCTION The shovelling of rock in stopes is still a basic and important operation in many gold mines in the removal of gold-bearing rock from the stopes. There is, however, little factual knowledge of the factors which influence the the rates of energy expenditure and work output, and of the way in which variations in these factors, individually or in combination, affect the mechanical efficiency of the mine workers. What for example is the influence of different rates of shovelling, shovel loads and distances of throw? How does stope width and dip of the stope affect the mechanical efficiency of men shovelling rock? Recently a simple physiological test was introduced into the gold mining industry for classifying Bantu recruits into those capable of hard, moderate and light work. If this test is used to select only those Bantu mine workers who are capable of hard work for the task of shovelling rock in stopes then the rate of energy expenditure which could be expected from these men is 1.5 litres/min for the entire period of the shift. With an adequate knowledge of the influence of the various factors which affect the rate of energy expenditure of men shovelling rock in stopes it would be possible to set work standards for Bantu mine workers in stopes. This should be done in terms of the rate of shovelling, the shovel load and the distance of throw for any combination of width of stope, dip of stope, condition of foot wall and grade of rock in such a way that the resultant energy expenditure would be the 'optimum' that could be expected from the men but would be within their capacities for physical work of an endurance nature (that is, 1. 5 litres/min from the 'average' Bantu mine worker). Work standards could thereby be determined for the different stopes of a mine on a sound and systematic basis. In order to supply the information required a study was carried out by the Human Sciences Laboratory in which the work output and energy expenditures (in terms of oxygen consumption in litres/min) were measured on six highly trained Bantu mine workers under the following conditions: (a) rates of shovelling of 3, 4, 5, 6, and 10 shovels per minute. (b) loads of from 9 to 18 lb on the shovel. (c) distances of throw from 8 to 20 ft. (d) stope width of 28 in., 42 in. and 72 in. (e) dip of stopes of 0°, 15° and 30°. (f) rough and smooth footwalls and various grades of rock size. This paper gives the main results of practical importance of this study. Method The experiments were designed and conducted in conjunction with the Work Study Department of one certain underground conditions such as variable stope widths, stope angle, etc., were made available in a mine Surface Training School and suitable subjects were selected from the large number of labourers being put through the training school. Subjects Bantu recruits who had returned to the mine for a new contract and who had previous underground experience on shovelling were considered to be suitable as subjects for the experiments. The particulars of the subjects are given in Table I. TABLE I PHYSICAL CHARACTERISTICS OF SUBJECTS Weight Height Surface area Max O2 capacity Subject (Kg) (cm) (sq meters) (Litre/minute) A 71.5 167.3 1.80 3.5 B 61.5 162.3 1.65 2.8 C 63.0 164.1 1.69 2.4 D 66.5 167.4 1.75 2.8 E 70.2 164.6 1.77 3.0 F 77.8 173.1 1.92 3.8 Training The method of shovelling, accepted by the Work Study Department, was demonstrated to the subjects who then practised the movements with empty shovels, under the supervision of an instructor. After the technique was mastered, the men started shovelling rock and were trained for at least four hours per day to work at the higher shovelling rates. Training was continued for three weeks to enable the subjects to achieve a reasonable degree of physical training and conditioning. Shovelling method In both the kneeling and standing positions the subjects faced the pile of rock, grasped the shovel in the accepted manner and pushed the blade of the shovel into the base of the pile of rock, sliding the blade between the rock and the concrete floor. In the standing position (72 in. wide stope) the back leg assisted in the movement by pushing the knee against the back of the hand holding the shovel handle. In the kneeling position the elbow was tucked into the side of the body so that the muscles of

By D. A. Vetter

A novel mathematical model is presented which describes the behaviour of beds of particles, of uniform size and shape but different densities, during autogenous separations. The approach used in the formulation of the dispersion model is a phenomenological one based on a statistical view, which leads to a diffusion-like representation of the autogenous-separation process. Although the model currently considers only density-related phenomena, it accounts quantitatively not only for the density-segregation aspects of the process but for the interactions between the particles. Quantitative predictions of the dispersion model are compared with the results obtained in tests using a specially constructed experimental batch jig, and it is shown that the model provides an adequate quantitative description of the process for particles of uniform size and shape. It is pointed out that, for the description of more complicated autogenous separations, a more rigorous formulation of the particle drag and density-segregation terms will have to be incorporated into the dispersion model. Nonetheless it is concluded that the model as presented in this paper provides not only a novel insight into the mechanisms of autogenous separations but a means by which to analyse similar systems.

Jan 1, 1987

Ausmelt is supplying commercial quantities of an alkyl hydroxamate flotation collector AM28 for flotation of oxide and supergene base metal ores and tailings. AM28 is a non-hazardous product used as a ten per cent to 50 per cent solution in dilute potassium hydroxide. It is a selective flotation collector for oxide or oxidised base metal minerals and replaces conventional sulfidisation for oxide mineral flotation. At Radio Hill, the AM28 is used in conjunction with traditional sulfide collectors, which allows simultaneous flotation of oxide and sulfide copper minerals. The Fox Resources Radio Hill copper concentrator near Karratha, Western Australia, is currently configured to treat supergene copper ore sourced from the West Whundo open pit. This Archean VMS type copper deposit has been deformed and remobilised with uplift, erosion and weathering to form a significant supergene zone. The sulfide copper minerals present in the upper zone are digenite and chalcocite with lesser chalcopyrite and covellite. Oxide copper minerals present include cuprite, with lesser malachite and azurite. Gangue minerals include quartz, talc and chlorite. Plant trials at Radio Hill are reported for supergene West Whundo ore, where the AM28 was stage added into the circuit at nominally 80 g/t. Plant data over three months shows the copper recovery increased consistently from around 50 - 60 per cent to above 70 per cent when AM28 was added. This has been proven statistically. The grade of the concentrate was consistent with and without AM28, at nominally 22 - 24 per cent copper.

Jan 1, 2007

By L. G. Snyman

"South Africa is well endowed with a plethora of valuable minerals, as well as being of world renown for its significant ecological and cultural resources. The unfortunate reality is that these two important attributes often come into collision when developmental decisions are made. Robust environmental planning tools are required to guide such development in areas of heightened sensitivity. Environmental management frameworks are one of the tools that can attempt to achieve the desired developmental and ecological balance by utilizing early identification and mapping of sensitive ecosystems and resources to assist in pre-empting potential future land use conflicts. This paper unpacks the characteristics of environmental management frameworks and further investigates their potential, as well as its current design and implementation challenges. The findings show that environmental management frameworks have the potential to provide meaningful resource information to decision-makers on the opportunities and risks of developments in sensitive areas. They further provide a platform and process through which local stakeholders can voice their opinions and collectively drive the developmental priorities of the identified area.IntroductionAt the core of a harmonious and prosperous society is the balancing of a broad spectrum of needs, rights, and imperatives. As South Africa’s resource and energy needs expand, it becomes increasingly important to safeguard environmental rights and ensure sustainable development through creative measures. The State’s drive for accelerated development to meet the targets in the National Development Plan 2030 is contributing to the growth of invasive developments in previously undeveloped areas. The unfortunate reality is that the heightened tensions between rapid economic growth and environmental sustainability are threatening sensitive areas."

Jan 1, 2017

By M. Rudman, L. Pullum, L. J. W. Graham

Centrifugal pumps are the workhorse of hydraulic conveying systems but their performance is derated when viscous non-Newtonian fluids, such as pastes and/or coarse solids are present. The reduced performance for purely viscous Newtonian fluids may be calculated using techniques such as the Hydraulic Institute method, but similar deration for non-Newtonian fluids is not so easy to apply. As part of the AMIRA P599 project investigating high concentration suspension pumping, centrifugal pump tests were systematically conducted on a wide range of non-Newtonian coarse particle suspensions. Suspension sup to 38% v/v of coarse particles with mean diameters in the range of 1.1 < d50< 3.4 mm suspended in carrier fluids with dynamic yield stresses of 0 < t?< 17.2 Pa and shear thinning indices in the range 0.35 < n< 0.79 were examined. Techniques such as the Hydraulic Institute de-ration method require a characteristic shear rate to be assigned before application with a non-Newtonian fluid, and a method based on pump geometry, fluid rheology and flow rate is proposed. This method predicts the dramatic characteristic reduction in head at low flow rates that is often observed and explains why larger pumps are relatively insensitive to this form of head deration. Head deration due to the presence of coarse particles in non-Newtonian carrier fluids is seen to follow similar trends to that of Newtonian suspensions and often dominates the total deration procedure.

Jan 1, 2007

A set of six design principles for rock engineering was developed by Bieniawski: design objectives; minimum uncertainty; simplicity of design components; state-of-the-art practice; optimization; and constructability. These principles translate into a ten-step design process. Although this methodology was developed for rock engineering, it is applicable to any design process, feasibility study, etc. Diligent use of such a process will ensure that a defensible design or evaluation has been carried out. Recently a ?strategic conversation? process has been identified by Ilbury and Sunter that includes the following ten steps: scope; players; rules of the game; key uncertainties; scenarios; SWOT analysis; options; decisions; measurable outcomes; and meaning of winning. A comparison of these steps with those of the design process shows a remarkable correlation. This is perhaps not surprising since engineering design is a strategic up-front issue, and front end loading in a project is critical to achieve the expected project performance. Based on the close correlation between the strategic conversation and engineering design processes, a circular design process, rather than a linear process, is proposed. The ?circle of design? better reflects the importance of review and monitoring in the two phases of successful design and implementation?defining the design, and executing the design.

Jan 1, 2009

By C. E. Dohm

The paper serves to show the importance of both a geological model and geostatistical model that support one another in mineral resource evaluation. It highlights the advantage of reference models for the geometry, the geological, statistical and geostatistical models of various orebody types and introduces a method for quantifying the combined uncertainty in these models. The example presented reveals how the above levels of information can be applied to add value to a resource evaluation process. It is a generic example in that it is the technique of combining uncertainty in the geological model (boundaries) as well as the grade model to assess the overall risk in the estimation of the resource. Data from the coal industry is used to illustrate the techniques. The geological uncertainty is considered via categorical simulations and these are combined with simulations of the variables (grades, thickness,) being estimated in the resource. The simulation techniques used are based on the application of GSLIB software1and a general discussion of the two simulation processes is included. In conclusion the paper demonstrates how the results of two types of conditional sequential simulation can be combined to produce confidence limits that take both uncertainties into consideration. This technique does not replace the resource estimation; it serves as an additional tool to quantify confidence in the resource evaluation model. The topics considered in this contribution are in terms of continuous improvement of mineral resource evaluation.

Jan 1, 2003

By P. J. Lloyd

Society is fully justified in its concern about the environment, but that concern may, at present, be too uncritical It is, for instance, essential to establish that there is a valid environmental impact, and that there is truly a causal link between a human activity and an observed shift in environmental conditions. In establishing these, it inessential to recognize that scientific proof offers consistency, but that it can never provide completeness. Thus, no amount of scientific endeavour can ever prove that mitigation of the effects of human activity will be perfect. Society normally expresses its concern through legislation. The existing legislation in South Africa is reviewed, and it is found that [>legislation regarding water is probably too stringent to be effective, >legislation regarding air and land use is probably too lax, >all the environmental legislation is too fragmented to be efficient, and the Department of Environmental Affairs is hamstrung by inter-departmental rivalry. ] It is accordingly concluded that, if means are to be found for ensuring adequate mitigation of environmental impact in the face of ongoing economic development, it is necessary to establish a Judicial Commission on Environmental Affairs advised by, but given greater powers than, the departments currently active in environmental maters. This Commission should be charged with creating, perhaps over a decade, a body of legislation that would guide development while protecting the environment in its widest sense.

Jan 1, 1994

By H. M. Krieg, M. J. Ungerer, C. G. C. E. van Sittert, D. J. van der Westhuizen

"The transition metals tantalum (Ta) and niobium (Nb) are of significant importance, for example in the nuclear energy sector where they are used as cladding materials, as well as in capacitors and specialized materials. For these applications a high-purity metal is needed. The separation of Ta and Nb is always a challenge since they are found together in nature and have similar chemical and physical properties, resulting in costly and laborious separation processes. A technology that has been used successfully for the separation of these metals entails solvent extraction (SX)1. While separation was achieved in a previous SX study using a sulphuric acid (H2SO4) medium with the extractants diiso-octyl phosphinic acid (PA) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), due to the absence of speciation data for Ta and Nb it is not clear how the separation occurred.One method that might be suitable for determining the speciation of a reaction is molecular modelling. Calculations based on the densityfunctional theory (DFT) are now used not only for light elements and small molecules, but also metal complexes, heavy metals, and especially metal separation in SX2. In this study the aqueous phase used during SX was investigated by studying periodic systems of Ta, as a metal and in salt form, when it is in contact with H2O and H2SO4. The results were used to predict the reaction mechanism occurring during SX. Results showed that (i) in a 1:1 acid-water ratio, the deprotonation of H2SO4 was endothermic, (ii) in a 1:5 ratio deprotonation was exothermic forming HSO4 -, and (iii) in a 1:10 ratio double deprotonation occurred to form SO42- exothermically."

Jan 1, 2017

By D. Krebs, Tero Korhonen, X. Yang, A. Kirpala, N. Heino

At present, over 85% of the world’s rare earth oxides are produced from the bastnäsite ores, found mainly in China. Meanwhile, the ion adsorption ores are the most important sources for heavy rare earth production. As the demand for rare earth materials in the world increases, other forms of rare earth deposits will become new potential resources of rare earth production in the future. In this paper, flotation performance of a steenstrupine ore from the Kvanefjeld deposit for rare earth recovery was studied through laboratory bench testwork. The effects of various factors including grinding size and collector dosage on recovery and selectivity of the selected rare earth elements, La, Ce and Y, were investigated. A rare earth concentrate with the grades of La 2.8 wt%, Ce 5.1 wt% and Y 1.0 wt% at recoveries of 80.5% La, 79.8% Ce and 55.3% Y was obtained in optimum conditions. Further potential to improve the efficiency of REE flotation was discussed. Keywords: Rare earth elements, flotation, steenstrupine, Kvanefjeld deposit

Jan 1, 2020

For the past 12 years, the Universities of Stellenbosch and Cape Town have hosted an annual symposium to discuss research topics in Minerals Processing. Since 1987, this meeting has been held under the auspices of the Western Cape Branch of the South African Institute of Mining and Metallurgy, and has enjoyed much national and international support. In 1993, in place of the usual Symposium, the Branch and Universities collaborated with CSM Associates Ltd and Minerals Engineering Journal is organizing the international Minerals Engineering &apos;93 Conference in Cape Town.

Jan 1, 1993

By B. Rezai, Z. Pourkarimi, M. Noaparast, S. Chehreh Chelgani

Nanobubbles (NBs) flotation separation can be an indicator for improving the efficiency of fine particles through the conventional process. Since flotation reagents such as frothers can reduce bubble size, they can potentially be used for the generation of NBs and develop a selective NB flotation separation. This study explored the flotation separation of fine phosphate particles from their associated minerals in the presence of NBs, which were generated by using a phosphate flotation reagent (Flo-YS: collector-frother). The results of flotation tests showed that in the presence of NBs, the flotation efficiency was significantly improved. However, in the presence of NBs, surface chemistry analyses (Fourier Transform Infrared Spectroscopy and High-Performance Liquid Chromatography) illustrated that the collector adsorption on the surface of phosphate particles decreased. A comparison between outcomes of various phosphate flotation conditions indicated that increasing the flotation efficiency in the presence of NBs may be due to the aggregation of fine particles by the generated NBs, and also selective adsorption of NBs (hydrophobisation) on the surface of particles. In other words, generating NBs by selective collectors may increase efficiency and decrease the collector consumption of a flotation process. Keywords: Phosphate, selective separation, fine particles, collector-frother, efficiency, mechanical flotation cell

Jan 1, 2020

By M. Helm

Over the last 40 years, numerous investigations have focussed on the preg-robbing capacity of carbonaceous material during gold ore processing. Various techniques have been applied to characterize the physical and chemical properties of the carbonaceous material in efforts to predict its preg-robbing capacity. The present study, which forms part of an ongoing investigation, is specifically designed to increase the understanding of preg-robbing in ores containing carbonaceous material. In excess of 100 samples from 13 gold mines located in major gold provinces of the world have been incorporated into the present study. These samples were characterized using industry standard metallurgical techniques and were shown to have gold adsorption capacities ranging from a few grams to many hundreds of grams of gold per ton of ore. Further analysis showed that the crystalline nature of the carbonaceous material, which is related to its geological history, is important in determining the preg-robbing capacity of an ore. This finding builds on the common understanding that the preg-robbing behaviour of an ore is related to the amount (or abundance) of carbonaceous material present in that ore. In this study, Raman spectroscopy was used to evaluate the physical nature of carbonaceous material. This is a tool which has been successfully applied by researchers for the characterisation of carbon materials, with respect to crystallite size and lattice defects. Raman analysis of the samples included in this study showed varying degrees of disorder in the carbonaceous materials from the different deposits. Comparison of the Raman spectra with the gold loading capacities of the samples indicated a direct relationship between the structure of the carbonaceous material and its capacity to preg-rob gold. From this, a simple and robust method has been developed based on the Raman spectra of the sample and carbonaceous material content to predict the preg-robbing capacity of an ore. The potential exists to develop a predictive tool using Raman spectroscopy for characterising the preg-robbing capacity of an ore. Such a tool would have potential application in projects ranging from the early stage of exploration through to more detailed feasibility studies and mining operations. The result of applying the predictive method outlined in this paper would be the effective and proactive management of the deleterious influence of carbonaceous material on gold recovery in mining operations.

Jan 1, 2009

By J Taguta, B. McFadzean, P. E. Ngoepe, M. G. Mulaudzi

Computational modelling methods and isothermal titration calorimetry (ITC) were employed to investigate the interaction of a pyrite surface with thiol collectors. Modelling work was conducted in the presence and absence of water. Microcalorimetry was employed to investigate the resultant energy of interaction pyrite as a result of mineral-collector interactions. Sodium ethyl xanthate (SEX), diethyldithiocarbamate (DTC) and diethyl dithiophosphate (DTP) were investigated in this study. The results showed that the calculated surface energies and morphologies for FeS2 showed that (100) and (111) are the most stable surfaces. The morphology also indicated the appearance of the (100) and (111) surface facets and no presence of others. The calculated adsorption energies between thiol collectors and the pyrite surface were always more exothermic than the experimentally determined ones. When comparing different ligand types with the same alkyl chain length, the heat of adsorption of diethyl-DTC was greater than that of ethyl xanthate and diethyl-DTP for pyrite. Experimentally, the diethyl DTP barely adsorbed onto the pyrite surface and this may be due to a different mechanism of action. In computational calculations, water adsorption was found to reduce the reactivity of the Fe atom for the interaction with thiol collectors, and bring the adsorption energies closer to the magnitude of the experimental values. Keywords: Computational modelling, microcalorimetry, experimental and thiol collectors, adsorption energies

Jan 1, 2020