Search Documents

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By A. Sissing

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering) degree Thermophilic bioleaching, conducted at temperatures in excess of 65°C, provides considerable benefit over mesophilic bioleaching, particularly through extending the extent of leaching of base metal minerals such as chalcopyrite. Thermophilic bioleaching is facilitated through a group of micro-organisms known as the Archae, well adapted to extreme environment. In order to maximize the space time utilization of the stirred tank reactor in the thermophilic bioleaching process, it is desirable to maximize the loading of the finely divided mineral phase present while not adversely affecting the microbial performance. In this paper, the effect of the loading of the solid particulate phase on the bioleaching performance of Sulfolobus metallicus was studied in a stirred tank reactor. Emphasis was placed on the effect of the concentration of the finely divided solid phase (35 ? 75 µm). A model system comprised of 3% (w/v) pyrite in the presence of varying quantities of quartzite in the range 0 to 24% (w/v) was used to obtain the different solids concentrations. The bioleaching experiments revealed similar bioleaching performance in the presence of 3 to 18% (w/v) total solids. Above 18% (w/v) total solids (15% quartzite loading), bioleaching was impaired progressively with increasing solids concentration. At the highest solids loading studied of 27% (w/v), bioleaching was still observed. In terms of mass transfer, oxygen transfer potential was not significantly influenced in the bioleaching process over the range of solids investigated.

Jan 1, 2003

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

By D. A. Spencer, L. J. Gardner

In light of the apparent productivity benefits provided by mechanised stoping, Impala Platinum Limited commissioned a study to investigate its possible implementation for mining reserves located 1200 – 1700 m below surface. This paper records the methodology employed for designing a support system for such mechanised mining, as well as initial conclusions of the work done. Preliminary results show the concept to be technically feasible; work was however stopped due to financial non-viability. En considération des bénéfices de production apparents que donne l’exploitation par gradins mécanisée, Impala Platinum Limited a commissionné une étude visant à examiner sa mise en œuvre possible pour des réserves minières situées à 1200 – 1700 m sous la surface. L’étude présente rapporte la méthodologie employée pour créer un système de support pour ce genre d’exploitation mécanisée, ainsi que les conclusions initiales de ce projet. Les résultats préliminaires montrent que le concept est techniquement faisable ; cependant le travail fut arrêté à cause de difficultés de rentabilité. Im Licht des offensichtlichen Produktivitätsnutzens auf Grund mechanisierten Stossbaus, kommissionierte Impala Platinum Limited eine Studie, die dessen mögliche Implementierung für den Abbau von Reserven 1200 - 1700 m unterhalb der Oberfläche untersuchen soll. Dieses Elaborat dokumentiert sowohl die Methode die für das Design eines Unterstützungssystems für eine derartige mechanisierte Abbauweise angewendet wird als auch die anfänglichen Konklusionen der geleisteten Arbeit. Anfängliche Resultate zeigen daß das Konzept technisch durchführbar ist; die Arbeit wurde jedoch wegen der finanziellen Nichtrealisierarkeit gestoppt.

Jan 1, 2003

COALTECH 2020 initiated a research project to provide the coal mining industry with a modelling tool to determine the expected types of subsidence, risks and the investment required in post-closure funds to cater for subsidence associated with bord and pillar mines. A detailed literature review was conducted to determine the most important parameters in calculating the cost associated with surface subsidence. A subsidence prediction model was developed to determine the likelihood of different types of subsidence. The study made use of current knowledge of failure mechanisms and its aim is to assist the industry and government in arriving at the most suitable arrangements when authorities require financial instruments to assure compliance with environmental regulations.

Jan 1, 2003

By J. D. Stone

This paper briefly reviews the adequacy of existing management theories and practices and the managerial proficiency or competency in the South African mining industry. The investigation revealed that existing management practices are totally inadequate to enable all employees on all the levels of the mining industry to achieve the results required from them, in all aspects, at all times. As a result, the South African mining industry is gradually losing its long standing reputation as a relative cheap, competitive, and reliable supplier of minerals to the local and global markets. According to some prominent management authors and theorists, an all-inclusive unified management theory does not exist at present. In this paper the authors summarize the main aspects of a newly developed comprehensive, practical, and integrated management method. It is believed that the application of this method would significantly improve the future performance and competitiveness of the South African mining industry

Jan 1, 2010

By J. L. Deutsch

Block model estimates are commonly calculated by the well-established technique of kriging. The mathematics are well established, but implementation details require site-specific considerations. Checking and measuring the performance of the estimates is important to ensure the block model is suitable for its intended purpose. There are different criteria for long-term planning and short-term planning. The implementation of kriging should be checked with cross-validation and assessed for conditional bias and departure from theoretical optimality with the calculation of kriging efficiency. A new expression of kriging efficiency, which compares the kriging variance with the theoretically optimal kriging variance, is developed to aid in this assessment. The assessment tools presented here can be applied in a number of situations; however, ordinary kriging with a reasonably large search performs well in most cases.

Jan 1, 2014

By C. Marais

The use of machine vision in the monitoring and control of metallurgical plants has become a very attractive option in the last decade, especially since computing power has increased drastically in the last few years. The use of cameras as a non-intrusive measurement mechanism not only holds the promise of uncomplicated sampling but could provide more consistent monitoring, as well as assistance in decision making and operator and metallurgist training. Although the very first applications of machine vision were in the platinum industry, no automated process control has been developed for platinum group metals (PGMs) as yet. One of the reasons is that to date froth features could not be related to key performance indicators, such as froth grade and recovery. A series of laboratory experiments was conducted on a laboratory-scale platinum froth flotation cell in an effort to determine the relationship between the platinum grade and a combined set of image features and process conditions. A fractional factorial design of experiments was conducted, investigating 6 process conditions, namely air flow rate (x1), pulp level (x2), collector dosage (x3), activator dosage (x4), frother dosage (x5) and depressant dosage(x6), each at levels. Videos were recorded and analysed to extract 20 texture features from each image. By using artificial neural networks (ANN), the nonlinear relationship between the image variables and process conditions and the froth flotation grades could be established. Positive results indicate that the addition of image features to process conditions could be used as sufficient input into advanced model based control systems for flotation plants. Keywords Flotation, machine vision, image analysis, neural networks.

Jan 1, 2011

By J. P. Gous, J. J. Sutherland

"Transalloys is a silicomanganese (SiMn) producer located in South Africa, and uses only local manganese ores to produce SiMn alloy. The plant operates five open submerged arc furnaces (SAFs) with an annual capacity of 180 000 t of saleable SiMn.Maintaining tap-holes is critical for effective furnace operation, allowing proper drainage of the furnace with minimal operator interference. Using a claygun and drill arrangement installed at each furnace, tapping occurs every four hours. Tap-holes are maintained through mickey replacement and brick repairs. Three furnaces have SiC tap-holes and two have graphite tap-holes.This paper gives a review of SAF operation, furnace and tap-hole design, daily tapping operation, and maintenance practices for repairing tap-holes.IntroductionDefining tap-hole life cycle, Steenkamp et al., (2016) highlighted four main steps: installation during furnace relines, day-to-day operations, tap-hole maintenance, and tap-hole repair. The authors argued that the design of the tap-hole area should allow for all four stages in the tap-hole life-cycle. Design principles for each stage were presented using silicomanganese (SiMn) production as a case study. Here we present a further analysis of the case study by providing practical examples of how the tap-hole life-cycle is managed at Transalloys during the design, operation, and maintenance of submerged arc furnaces (SAFs) applied in the production of SiMn.BackgroundTransalloys is the largest producer of SiMn in Africa. Its smelter complex is based outside the town of eMalahleni, in the Mpumalanga Province of South Africa. Transalloys was commissioned in the mid- 1960s as a high- and low-carbon ferrochromium plant based on the Perrin process. In 1967 the plant was converted to SiMn production because of constraints in the ferrochrome market (Basson, Curr, and Gericke, 2007; Bezemer, 1995). Today, the installed production capacity is 180 000 t of SiMn annually. Plant operations consists of five SAFs (see ratings in Table I), operating 24 hours a day, 365 days a year (including maintenance), involving 280 permanent employees, with up to 120 contract employees on site at any given time."

Jun 1, 2019

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By S. Uludag

Spontaneous combustion of coal has been studied by laboratory techniques using an apparatus in a small-scale laboratory testing. Coal?s inherent characteristics can be measured using Differential Thermal Analysis (DTA) and Crossing Point Temperature (CPT) methods. The DTA curve obtained after testing is compared with actual inherent moisture and its effect on spontaneous combustion has been investigated. It has been found that the Wits-Ehac Index increases as the inherent moisture of the sample increases. Therefore it can be deduced that liability to spontaneous combustion increases with increased inherent moisture. In addition, volatiles have a catalytic affect on self heating immediately after the inherent moisture is reduced. This is identified as stage two in the thermogram. The inherent moisture has a cooling effect during the initial stages of testing and is visible in the DTA thermogram. In addition, while an increase in carbon content means an increase in Wits-Ehac Index value, an ash content decreases the likelihood of on spontaneous combustion. Keywords: Spontaneous Combustion, Differential Thermal Analysis, Crossing Point Temperature, Moisture, Coal, Laboratory Testing.

Jan 1, 2007

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By A. K. Anyimadu

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004,and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November 2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Keywords: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, platinum, palladium, PGMs, tailings.

Jan 1, 2007

By G. L. Smith

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2007

By M. Nete

Qualitative analysis of three mineral samples from northern Mozambique was accomplished by X-ray diffraction (XRD), microscopy, scintillation, and magnetic determination. Chemical characterization was accomplished using ICP-OES and pressed powder XRF after dissolution using microwave-assisted digestion and flux fusion. The samples consisted of a mixture of minerals with tantalite as the major component, with minor amounts of microlite, quartz, mica, accessory garnet, and tourmaline. Incomplete dissolution was obtained using microwave digestion, with maximum recoveries of 90.25 ± 0.06% and 88.90 ± 0.04% for Nb2O5 and Ta2O5 respectively. Complete dissolution using Li2B4O7 resulted in recoveries of 98.5 ±0.2% Nb2O5 and 100.4 ± 0.3% Ta2O5.

Jan 1, 2012

By C. C. Pretorius

3D seismic surveys have become a well-accepted method of imaging sub-surface geology in the Bushveld Basin. Because both the seismic sources and receivers are placed at surface, most surveys are limited to imaging faults with >=7 m throw. However, some areas such as shaft infrastructure can benefit from the ability to detect smaller structures prior to shaft sinking. Borehole radar and logs such as the acoustic televiewer can identify these structures in the shaft barrel, but not within -200 m from the shaft. Therefore, Anglo Platinum has developed the method of high-resolution 3D vertical seismic profiles (VSPs) for structural sterilization of shaft sites prior to shaft sinking. VSPs utilize a surface source and sub-surface receivers deployed down a borehole. This means that seismic energy goes through the near surface only once, and therefore suffers less frequency loss than when both source and receivers are on surface. Furthermore, VSPs can record 3 component (3C) data which comprises P wave, Sh (horizontal) and Sv (vertical) wavemodes. Because S waves travel at about 0.6 of the velocity of a P wave, shorter wavelengths and therefore higher resolutions are possible using S wave data. VSPs were first used in their one dimensional, zero offset, mode to correlate borehole geology with seismic stratigraphy within seismic surveys. This showed that VSPs record -30% higher frequencies than surface seismic surveys. The program then applied two dimensional VSPs to the problem of imaging geological structure close to a borehole. 2D VSPs confirmed that high frequency results could be achieved, and that this enabled a more accurate image of the Merensky Reef than could be achieved by surface seismic data. Finally, the program has achieved the successful recording and processing of 3D VSP data, with both compressional and shear wavemodes giving a high resolution structural result. Although P wave data gives -30% frequency improvement over surface seismic surveys, S wave data can give as much as 80% improvement, further improving the structural image achieved. The high fixed costs of VSP surveys mean that they should ideally be run in multi-client batches, which can reduce the per borehole cost by up to 50%. Their application is anticipated to be on high value capital infrastructure with a geological risk from faults which are not imaged by surface seismics-generally in the sub-7 m range. Keywords VSP, 3D seismic, bushveld, platinum, resolution, imaging, shear waves, shaft sinking.

Jan 1, 2011

By A. K. Anyimadu

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November 2006 at the Potgietersrus Platinum (PPL)?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Keywords: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, platinum, palladium, PGMs, tailings.

Jan 1, 2007

By N. Reddy

The influence of local geology and rock mass characteristics on deformations during a rockburst caused by a controlled blast was studied. This was done by means of visual examination, mapping and photography both before and after the blast. We found that the ejected material was bounded mostly by fractures associated with the bow-wave fracturing and bedding surfaces and that existed prior to the blast. Most of the damage was caused by shake-out. This information is important input for the design of rockburst resistant support systems under conditions of moderate stress.

Jan 1, 2001

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005