Search Documents

By J. C. D. Gush

Paper written on project work carried out in partial fulfilment of Laboratory-scale testwork was undertaken to recover oxidic copper-cobalt minerals by froth flotation, which requires maintaining a certain sulphide level in the pulp. To improve control of the sulphide concentration, an electronic closed-loop system was designed that responds to the potential output of an ion-selective electrode. The PID control was improved by adding a pre-emptive control and a self-calibration feature; a data logging facility is also included. An inexpensive valve design was incorporated using locally available parts. The operating results of this control design are presented.

Jan 1, 2005

By J. H. van Laar, L. J. van der Walt, P. L. Crouse, H. Bissett, G. J. Puts

"SynopsisSilicon carbide nanopowders were produced using a microwave-induced plasma process operating at 15 kPa absolute and at atmospheric pressure. Methyltrichlorosilane (MTS) served as precursor, due to its advantageous stoichiometric silicon-to-carbon ratio of unity, allowing it to act as both carbon and silicon source. Argon served as carrier gas, and an additional hydrogen feed helped ensure a fully reducing reaction environment. The parameters under investigation were the H2:MTS molar ratio and the total enthalpy. The particle size distribution ranged from 20 nm upwards, as determined by SEM and TEM micrographs. It was found that an increase in enthalpy and a higher H2:MTS ratio resulted in smaller SiC particle sizes. The adhesion of particles was a common occurrence during the process, resulting in larger agglomerate sizes. SiC layers were deposited at 15 kPa with thicknesses ranging from 5.8 to 15 µm.IntroductionIt is well known that methyltrichlorosilane (CH3SiCl3 or MTS) decomposes to form silicon carbide (SiC) and hydrogen chloride (HCl) as shown in Equation [1]. The reaction kinetics and mechanisms for this reaction are thoroughly reported in the literature (Sone et al., 2000; Papasouliotis and Sotirchos, 1999; Kaneko et al., 2002; Wang et al., 2011)."

Jan 1, 2015

THE THIRD INTERNATIONAL GEOCHEMICAL EXPLORATION SYMPOSIUM (Summary Account) This Symposium, co-sponsored by the Canadian Institute of Mining and Metallurgy and the Society of Economic Geologists, was held in Toronto, Canada in April, 1970. Over 700 delegates attended from 26 countries. Ninety papers were presented at the symposium and another 18 papers were read by title. The programme included: An Opening Session, Five General Sessions, a session on Remote Sensing Methods, a session on Geochemical Prospecting for Petroleum and Natural Gas, a session on Primary Halos and Lithogeochemical Methods, and a session on Statistics and Evaluation of Geochemical Data. The delegates were welcomed by Dr J. M. Harrison, President of the Canadian Institute of Mining and Metallurgy and Dr C. H. Smith, Regional Vice-President, North America of the Society of Economic Geologists. Dr D. R. Derry of Toronto delivered the opening address to the Symposium entitled 'Geochemistry-the link between ore genesis and exploration'. Dr Derry considered the various hypotheses on the origin of economic mineral deposits and expressed his belief that the next ten years will show evidence of an increased proportion of ore bodies that owe their origin, at some stage in time, to supergene agencies. He stressed that 'there are no sharp divisions between processes that form and destroy ore bodies at or near surface and those that form or destroy them at a depth of 20 kilometres in the earth's crust. The more we understand about the migration and concentration of metals the more accurately we can apply this knowledge to searching for unknown concentrations, whether at rock surface or at depth. To learn more about these processes of ore genesis we must rely on geochemical studies co-ordinated with field observations'. The five general sessions included accounts of progress in geochemical prospecting in different countries of the world, case histories describing the application of soil, stream sediment, geobotanical and biogeochemical techniques, papers on the behaviour of different elements under varied environmental conditions, discussions on analytical methods and the use of stable isotopes in mineral exploration. It is anticipated that the proceedings of the Symposium will be published late in 1970 or early in 1971 as a Special Volume of The Canadian Institute of Mining and Metallurgy. All registrants at the Symposium will receive a copy of this publication and copies will be available for purchase. At a special meeting called during the Symposium, charter members of the Association of Exploration Geochemists approved a constitution and elected an interim Council which will organize procedure and formulate policy during the coming year. The interim president of the Association is J. Alan Coope, Newmont Mining Corporation of Canada Limited, Toronto, Canada. More information on the constitution and membership in the Association will be distributed to learned societies and technical magazines in the near future. Membership will be open to exploration geochemists in all countries of the world. SOUTH AFRICAN COUNCIL FOR PROFESSIONAL ENGINEERS Report on Registration The Professional Engineers Act (Act 81 of 1968) came into force on the 14th February, 1969. At the time it was recognised that the success of the Act would depend in large measure on the extent to which engineers in South Africa would become registered professional engineers in terms of the provisions of the Act. The promulgation of the Act and its provisions relevant to registration were the subject of considerable publicity during 1969. This has resulted in a rate of application for registration far beyond the capacity of the very active committees set up for this purpose by the South African Council for Professional Engineers (SACPE). To give some idea of the task before these committees and before SACPE itself, which must ratify each case,

By J. D. Swanepoel, S. Horn, C. J. Badenhorst

Diesel particulate matter (DPM) is the particulate component of diesel exhaust, which includes diesel soot and aerosols. When released into the atmosphere, DPM can take the form of individual particles or chain aggregates, with most in the invisible sub-micrometer range of 100 nanometres. The main particulate fraction of diesel exhaust consists of fine particles and because of their small size, inhaled particles may easily penetrate deep into the lungs. The rough surfaces of these particles make it easy for them to bind with other toxins in the environment, thus increasing the hazards of particle inhalation. DPM is a significant health hazard in underground mining operations, where the use of dieselpowered equipment in confined spaces can lead to high levels of exposure among people working in these environments. Classified as a carcinogen by the International Agency for Research on Cancer (IARC), DPM has been linked to severe health effects, including respiratory and cardiovascular diseases, as well as an increased risk of lung cancer. Effective management of DPM is essential not only for protecting people’s health but also for ensuring regulatory compliance, maintaining operational efficiency, and safeguarding the long-term viability of mining companies.

Mar 5, 2025

By E. Moosavi, K. Tolouei

In mine production scheduling problems are well-known, where most are categorised into deterministic and non-deterministic NP-hard problems because of their complexity. Many researchers have attempted to solve the problem by applying various optimisation techniques. While using traditional methods they observed extreme difficulty in solving highly complex problems. In the 1990s, many researchers addressed long-term production scheduling (LTPS) by using simulated annealing, the genetic algorithm, the tabu search algorithm, and the ant colony algorithm. These algorithms are known as the meta-heuristic algorithms, and have proved to be the most efficient algorithms for solving LTPS thus far. The firefly algorithm is one of the best methods for visualising problems related to LTPS, and provides the best possible optimisation. It is one of the simplest methods, and easy to apply to any NP-hard problem. The experimental, and comparison with other recently published algorithms shows that the proposed algorithm is feasible, and is an effective approach for long-term production scheduling problems. The results indicated that a better solution is obtained by the proposed method, compared to other methods in terms of cumulative net present value, and average ore grade. Additionally, the CPU time via the proposed model is roughly 2.52% higher than the other method.

Sep 1, 2021

By K. Premlall, R. M. Dire, H. Bissett, D. Delport

Tungsten carbide is a fine grey powder. It can be formed into shapes by compacting with the addition of a binder. Spherical particles are generally preferred in additive manufacturing as they pack together more efficiently than non-spherical particles, promoting a uniform powder bed density, better flowability, and elimination of internal cavities and fractures, resulting in a better quality of final product. The particle shape of powders can be transformed into spherical through the process of spheroidization. However, due to its high melting point, tungsten carbide could be difficult to spheroidize. Tungsten carbide was spheroidized using an inductively coupled radio frequency plasma at various plate powers between 9 and 15 kW. The influence of additional H2 in the sheath gas on the chemical composition of the tungsten carbide product was also investigated by means of XRD, which indicated that WC is converted to W2C at higher H2 concentrations. Optical analysis of SEM micrographs indicated that the spheroidization ratio increased with increased plasma energy.

Apr 1, 2021

By T. Mahlangu Mahlangu, T. Fungene, K. C. Sole

"Although oxygen is widely employed as the oxidant of choice in gold leaching by cyanide, its low aqueous solubility presents some drawbacks in practical application; hydrogen peroxide has therefore been considered as a possible alternative. The aim of this investigation was to study the catalytic decomposition of hydrogen peroxide, which generates an oxidizing intermediate species, and to understand its effect on cyanide destruction. Operating conditions that facilitated the effective decomposition of hydrogen peroxide were established by varying the pH and catalyst type and concentration. The oxidizing intermediate, detected using an indirect technique, was found to be the hydroxyl radical (OH?). OH? is commonly generated in acidic solutions, but this work demonstrated that it is also produced at the alkaline pH values necessary for cyanide gold leaching. The effects of free and complexed iron and copper catalysts on the oxidation and consumption of hydrogen peroxide and cyanide were also investigated. It was shown that the cyano complexes of Fe(II) and Cu(I) are also effective as decomposition catalysts. Hydrogen peroxide concentrations above 0.01 M decreased the free cyanide concentration, which was attributed to the probable formation of the cyanate anion (CNO-). Although cyanide consumption increased due to its oxidation in the presence of OH?, excessive cyanide consumption in the presence of copper was attributed primarily to its complexation by the unstable copper(I) cyanide species. Rate constants for the decompositions of H2O2 and cyanide by ferrocyanide and copper cyanide were calculated; the latter was identified as being a better catalyst. IntroductionLeaching of gold from its ores using cyanide has been employed for well over a century (Habashi, 2016). Addition of cyanide converts the gold into a cyanide complex (Au(CN)2 -) that is soluble in water (Wang and Forssberg, 1990). The leaching reaction can be represented as Equation [1]:"

Dec 1, 2018

By C. A. Garzonio, A. M. G. Affuso

The paper describes the analyses and the tests carried out on representative slabs of white Carrara marble which have highlighted the correlation between the micro fabrics and physical and mechanical parameters. The aim is to determine the conditions which indicate the triggering and evolution of the deformation phenomena. La note écrit l’analyse et les epreuves effectuée sur un echantillon représentatif de nombreuses dalles en marbrede Carrara. Les études montrent la correlation entre la minéralogie et les paramètres physiques et mecaniques. Le but est déterminer les conditions qui indiquent l’amorçage et l’evolutions des phénomènes de déformation. Diese Arbeit gibt eine Beschreibung der experimentalen Untersuchungen und der Analysen über die Marmorplatten von Carrara. Daraus resultiert, dass die Charakterisierung der Mineralogie und die Porosität der Gesteinsmaterialien die physikalische mechanische Degradation beurteilen und die Krümmungen bestimmen.

Jan 1, 2003

By M. L. Mahlatji

Mechanical alloying of an equiatomic mixture of crystalline Ti and Pt elemental powders in a high-energy ball mill formed an amorphous alloy by solid-state reactions. Mechanical alloying was carried out in an argon atmosphere at a rotation speed of 1200 r/min and a 20:1 ball-to-powder weight ratio, for time intervals of 4 to 40 hours. At an intermediate stage of mechanical alloying, scanning electron microscopy showed the formation of characteristic layered structures of inhomogeneous composition within the powder particles. X-ray diffraction analysis showed the gradual disappearance of crystalline Bragg peaks and the emergence of broad amorphous maxima as milling progressed. The amorphization process was completed after 8?12 hours. The amorphous state of the product indicated that temperatures during processing did not exceed the crystallization temperature of the alloy.

Jan 1, 2014

By S. Mohanty, K. Sarangi, S. Dash, P. P. Patra

Industrial effluent from various industries contains heavy metals that are a serious threat to humans, flora and fauna in water bodies, and the environment. The heavy metals are dumped after precipitation, which has serious environmental consequences. In this paper, a 2D axi-symmetry CFD model has been developed to study the extraction of chromium ion from industrial effluent, in a hollow fibre membrane, using Alamine 336 as the carrier and kerosene as the diluent. The Navier Stokes equation was used to predict the velocity profile of the aqueous and organic phases, and species transport equation, which considers both convective and diffusive mass transfer, was used to predict the concentration profile of the chromium ion in the computational domain. The distribution coefficient was experimentally determined at a pH 4, which was found to be the optimum pH. Numerical simulations were performed considering 11.11 mol/m3 of initial feed concentration for chromium ions and extractant concentration of 0.2 M. Simulations were carried out with various aqueous and organic flow rates, and validated with experimental data. Keywords: CFD, metal extraction, hollow fibre membrane, heavy metals

Jan 1, 2020

By C. van der Merwe, R. Lumbule, J. Kgomo

"The mining industry in the Democratic Republic of Congo has seen a significant expansion in copper and cobalt production in recent years. The greater proportion of this expansion has arisen through processing of oxide ores. The design of metallurgical processes for these oxide ores is based on the conventional equipment and layout for processing of sulphide ores, and comprises milling followed by leaching, solvent extraction, and electrowinning. The physical characteristics of the oxide ores, however, provide the process design engineer with an opportunity to examine critically the principles on which equipment selection is based and to design processes better suited to these ores. In 2015, ERG Africa began a project to expand the leaching capacity of the Luita hydrometallurgical facility. A number of innovative changes to the conventional process design were included in the modified flow sheet, which were validated when the project reached design throughput in November 2017. Of these changes, the most novel presented an alternative approach to mitigate the impact of colloidal silica on the operation of the solvent extraction plant. Introduction ERG Africa operates the Luita hydrometallurgical facility located at Kakanda in the Democratic Republic of Congo (DRC), treating malachite and heterogenite minerals to recover copper as electrowon cathode and cobalt as a hydroxide precipitate. The process was originally conceived as a heap leach operation followed by direct electrowinning of copper, with solvent extraction (SX) and electrowinning (EW) of cobalt. In preparing the sized ore for the heap leach operations, the undersized ore fraction at a P80 of 625 µm was discharged to a fines storage facility for later processing. This fraction carried with it approximately 30% of the copper contained in the run-of-mine (ROM) ore feed, and an equivalent proportion of cobalt.In a subsequent development, the cobalt SX section was converted to a copper SX facility, the leached cobalt being recovered from a bleed stream from the copper heap leach circuit. The operating cost for the process as then installed placed this facility well in the fourth quartile of the industry cost curve. The initial Luita operation was established in 2010 at a time when metal prices were above long-term averages (copper above US$3.00 per pound; cobalt above US$20.00 per pound), and the drop in prices in 2015/2016 presented a major challenge. The London Metal Exchange (LME) copper price dropped below US$2.00 per pound, with cobalt dropping below US$10.00 per pound in Q1 2016. This set in motion a range of improvement initiatives for the Luita operation. Central to this was the installation of a tank leach circuit to process the discarded fines and a modified SX circuit to manage colloidal silica. The revised Luita circuit reached design capacity in November 2017 and has proven to be well suited to processing of the oxide ore feed. This process design challenges the boundaries of conventional thinking in the areas of leaching, solid/liquid separation, solution management, impurity management, and metal recovery, and is the subject of this paper."

Nov 1, 2018

By B. H. Kim, S. K. Chung

RMR, Rock Mass Rating, is one of the famous rock classifications. However, RMR was proposed empirically and absolutely depends on the experience of engineer. Therefore, engineering verification is needed for RMR system itself. In this study, the factor analysis and the multiple regressions were performed in order to evaluate the validity of rating factor of RMR. Also numerical analysis was carried out using the FLAC based on Taguchi method, a kind of robust designs, in order to examine the support of tunnel corresponding to the revaluated RMR. As the result of the analysis new RMR was proposed with five minimized factors of intact rock strength, RQD, spacing, persistence and roughness of discontinuities. RMR est un des procédés de la classification du roc qui sont généralement utilisés. Mais RMR s'appuie sur l'expérience et se absolument soumet à l'expérience d'ingénieur. Il est donc nécessaire de vér- ifier techniquement sur le système de RMR. Dans cet étude, on met à exécution l'analyse du facteur et la régression multiple pour évaluer la convenance de la cause de classification de RMR. De même, pour évaluer le support du tunnel selon RMR réestimé, on a exécuté l'analyse de la valeur numérique par FLAC qui se base sur la lois de Taguchi, laquelle est une sorte de système du plan robuste. Selon le résultat de la régression multiple, il est proposé de nouvel RMR à partir de l’intensité de roc intact, RQD, l'espacement, la persistance et la rugosité RMR ist eine der weit benutzten klassifikationen fuer die felsenstuecke. Da aber RMR erfahrungs- maessig ist und ueberwiegend von der persoenlichen Erfahrung eines Ingenieurs entschieden ist, ist es mit Sicherheit notwendig, das RMR-system selbst technisch zu ueberpruefen. In diesem studium waren die faktorenanalyse und mehrfachregressionanalyse durchgefuehrt, um die gerechtigkeit der klassifikationenfaktoren von RMR zu bewerten. Ferner war noch eine numerische analyse mit ben- utzung von FLAC aufgrund der Taguchi-methode, eine art technik der robust design, eingefuehrt, um die tunnelstuetze infolge der neubewertung von RMR unterzusuchen. Gemaess der mehrfach regression analyse wurde eine neue RMR, die sich aus 5-eingeschraenkten faktoren wie intact rock strength, RQD, spacing, persistence und roughness von discontinuities zusammensetzen, in vorsch- lag gebracht

Jan 1, 2003

By F. P. Agterberg, A. G. Fabbri

"A statistical analysis was done on the locations of 718 copper and 1 257 gold deposits in Abitibi. This area of about 20 000 square miles is one of the better-explored metal-producing areas of Canada.Patterns of clusters were studied by harmonic analysis. Several two-dimensional power spectra showed a number of distinct peaks. Sets of crest lines for patterns of interfering waves were constructed on the basis of these peaks. They pass through elongated clusters of deposits which are spaced more or less equally. For copper these periodic regularities in location may coincide with geological structures largely of Archean age (major fractures and sedimentary belts indicating synclinal structures). A directional relationship with swarms of diabase dykes of known ages and distinct attitudes indicates that the gold mineralization is, in part, younger than the copper mineralization."

Jan 1, 2014

By NIM REPORTS

Notices CONFRRENCE ON COMPUTRRS IN ENGINEERING The above Conference, which is being organized by the Electrical and Electronics Board of the Institution of Engineer!!, Australia, ill to be held in Sydney on 16th and 17th May, 1974. It is being planned in conjunction with the Sixth Australian Computer Conference and will be held during the week immediately preceding the latter. NIM REPORTS Report No. 1495 A method for the determination of ekmental sulphur on the surface of sulphide minerals. Report No. 1500 The chromatographic separation and determination of nobk metals in matte-leach residues. Report No. 1505 The production of the refractory aluminium saicates, with special refererence to South Africa. Report No. 1517 Computer-controlled flotation plants in Canada and Finland. Report No. 1526 Heat of solution as a control of aqueous-ammonia concentration. Report No. 1529 South African costs of equipment for the metallurgical industry (197).

Jan 9, 1973

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By M. Pierce, E. Karampinos

"One of the main challenges in the numerical modelling of ground support in underground excavations is to reproduce the performance of the sequential installation of the reinforcement while capturing the rock mass behaviour of an advancing face in 3D. The 3D modelling approaches used to simulate the progressive advance of excavations are mostly continuum and often cannot reproduce the rock mass failure mechanisms. The 3D discrete element method (DEM) can better reproduce structurally controlled rock mass failure mechanisms and can explicitly represent the reinforcement elements. This paper builds on previous work that reproduced the structurally controlled squeezing conditions in an underground hard-rock mine using 3D DEM and the in situ behaviour of reinforcement under pull conditions. It addresses important issues on the way reinforcement is explicitly introduced in discrete element models. A pseudo-3D model is employed to overcome the computational restrictions and time limitations of a 3D modelling approach. The work focuses on the scaling of the material properties of the ground support elements when the thickness of the model is not equal to the out-of-plane spacing of reinforcement. It demonstrates the scaling methodology based on the type of the modelled reinforcement elements used and investigates the significance of this approach. The advantages and disadvantages of this approach with respect to 2D and 3D methods are discussed. The results are compared with field data and previous modelling work done at the mine. IntroductionNumerical models can provide significant insight into the anticipated behaviour of underground excavations. The modelling of ground support, however, is not a trivial exercise. An effective representation of ground support in underground excavations should capture the behaviour of both the rock mass and the support elements. When numerical models are used for design purposes, the complexity of the problem requires significant time and expertise (Sweby, Dight, and Potvin, 2016).At a laboratory scale, numerical models have successfully reproduced the results of laboratory tests on rockbolts by explicit modelling of the bolt, the borehole, and the grout. Chen and Li (2015) used a continuum FLAC3D (Itasca Consulting Group Inc., 2012) model to simulate the mechanical behaviour of D-bolts as observed experimentally. Grasselli (2005) used a 3D finite element code to model the behaviour of fully grouted rods and expandable bolts under shear."

Dec 1, 2018

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

By G. Dellas, R. Mangera, A. Voigt

"X-ray transmission (XRT) sorting has become the preferred recovery technology option in several parts of the diamond-winning flow sheet. In the De Beers Group, applications of XRT are found across kimberlite, alluvial, and marine operations. This is the result of intensive R&D conducted over the years to arrive at a suite of machine embodiments capable of sorting and auditing diamonds across all size ranges.The first applications in the marine environment used the technology in an auditing mode, and served as a useful early predictor of diamond content weeks ahead of sorthouse returns. The same machines are now available with ejection capability to produce high final product grades. The next application was tests on coarse alluvial gravels as an alternative to dense medium separation. The results were very encouraging, and tests are planned for both green- and brownfield kimberlite environments, as well as to explore an alternative to conventional techniques in final diamond recovery. At the Jwaneng mine Large Diamond Pilot Plant (LDPP), the objective is to recover diamonds in the size fraction –45 +25 mm.The technical challenge remains in the finer sizes, for high-capacitymachines as direct alternatives to conventional diamond recovery technologies. This is an area of ongoing R&D and it is only a matter of time before the breakthrough emerges. X-ray transmission fundementalsXRT makes use of X-ray imaging techniques to analyse objects and materials, and has a wide range of applications from baggage scanning for security purposes (Martz et al., 2016), to recycling of waste material (Owada, 2014). During the last decade XRT has been applied to an increasing extent in the minerals processing industry (von Ketelhodt and Bergmann, 2010; Sasman, Deetlefs, and van der Westhuyzen, 2018). Dual-energy XRT (DE-XRT), in which images of the target material are obtained at both high and low Xray energies, allows for elemental analysis and therefore can be used to discriminate between various minerals.A DE-XRT system makes use of a dualenergy X-ray line scan sensor to generate images of transmitted X-rays (Figure 1). Dualenergy refers to the camera, which contains two sensors, one responding to low-energy Xrays and one to high-energy X-rays. Feed material can be imaged either while on the belt, or while in flight."

Feb 1, 2019

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"The primary function of a tundish in the steelmaking industry is to serve as a buffer tank, accepting molten steel from the batch ladle process and allowing it to be cast continuously. However, modern steelmaking has more stringent demands for the quality of the steel product, requiring increased control over the properties of the molten steel before casting. For this reason tundishes have been developed as metallurgical reactors to serve as the final step in refining of the molten steel by removing non-metallic inclusions, preventing the formation of new inclusions, and promoting chemical and thermal homogeneity. In this study the flow behaviour in a four-strand tundish was investigated by means of a half-scale water model as well as numerical modelling. Both the numerical study and physical model were used to characterize residence time distribution (RTD) in the vessel and calculate properties pertaining to the tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices was prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing short-circuiting and provided surface-directed flow, which aids inclusion removal in the slag. Despite the benefits of the use of turbulence inhibitors, it was observed that the upward-directed flow increased the maximum turbulence kinetic energy near to the surface by approximately 120% compared with the bare tundish. Therefore the potential for slag entrainment should be considered during the design and operation of tundishes utilizing turbulence inhibitors."

Jan 1, 2014