Search Documents

By P. Fu, Y. Ma

Residual collectors and their byproducts (e.g., CS2) in flotation effluents can cause water contamination and even result in serious health hazards to humans and animals, Therefore, residual flotation reagents should be removed properly before discharge or recirculation into flotation circuits. In this work, four thiol collectors (potassium ethyl xanthate (EX), sodium diethyl dithiocarbamate (SN- 9), O-isopropyl-N-ethyl thionocarbamate (Z-200), dianilino dithiophoshoric acid (DDA)) were chosen as model pollutants. The collector removal, mineralisation and byproduct formation were compared by sole O3 and O3/UV185+254nm. The degradation rate constants of thiol collectors by O3/UV185+254nm were 2~6 times higher than those by sole O3. The mineralisation of collectors was also remarkably enhanced by O3/UV185+254nm. The degradation efficiency by O3/UV185+254nm had the order: EX>SN-9>>Z- 200>DDA. The Z-200 and DDA were refractory flotation reagents. The degradation of thiol collectors caused the reduction of solution pH and the increase of ORP and conductivity. However, the O3/UV185+254nm achieved more evident changes of these parameters than sole O3. During the degradation of thiol collectors, less than 4% of total sulfur in collectors was emitted into air as CS2 and H2S. Compared to sole O3, the O3/UV185+254nm had additionally included UV185+254nm photolysis and O3/UV254nm, resulting in higher efficiency in removing collectors. The O3/UV185+254nm was an effective process in treating mineral flotation wastewaters containing organic reagents. Keywords: Thiol collectors; flotation effluents; ozone; vacuum-UV; degradation, mineralisation

Jan 1, 2020

By J. Arzuúa, U. Castro-Filgueira, L. R. Alejano, F. Malan

"Pillar design for underground mining is typically done using empirical formulae or numerical modelling. Practical experience and recent literature, nevertheless, illustrate the shortcomings of these design approaches. Ongoing monitoring of pillars is therefore recommended to minimize the risk associated with these designs.In a mine where a large number of pillars are cut, different pillar strengths can be expected owing to variations in rock mass strength from area to area. This problem is compounded by the fact that in mining environments the pillars are not always cut according to the prescribed dimensions. Although the original design using either empirical methods or modelling may predict stable pillars, unstable pillars will be encountered in reality. Very conservative designs with large factors of safety may circumvent this problem, but this approach is uneconomical.A possible solution to localized stability problems may be to enhance the strength of a few unstable pillars. It may even be hypothesized that reinforcing a few critical pillars may prevent ‘pillar runs’ on a much larger scale. Rockbolting, strapping of pillars, and pillar shotcreting have occasionally been used in the past as possible solutions. It appears that these have not been successful in all cases and large collapses have occurred in spite of the pillar remedial work.The authors investigated the strapping of pillars by conducting laboratory tests on cabled rock specimens. The results were qualitatively compared to actual attempts of pillar reinforcement available in the literature, as well as additional observations in an old haematite roomand- pillar mine in Spain. Based on these results, the value of steel cabling and mesh wrapped around pillars to improve stability is demonstrated. Some cases where this approach will not be successful are also discussed."

Jan 1, 2017

By M. A. Roberts

Oebswana's Jwaneng Mine (south-central Botswana) is the richest diamond mine? in the world and has been contributing substantial revenue to Botswana since the mine started operating in 1982. The resource consists of 3 separate volcanic pipes/vents namely North, South and Centre pipes (2 additional small kimberlite bodies have also been intersected within the mining pit) which erupted through Transvaal strata and the overlying Karoo sediments -245 million years ago. Although earlier drilling and geophysical surveys suggest that the 3 pipes extend to depths greater than 1 km below the surface, the resource is only at an indicated level of confidence to a depth of 400m, and mining activities will start exploiting the inferred resource material below 400m in 2014.

Jan 1, 2010

By D. K. Chibwe, P. Taskinen

"Typical operation of industrial Peirce-Smith converters (PSCs) used in copper smelting results in several common phenomena such as excessive splashing, slopping, tuyere blockage, and low converter campaign life due to high tuyere line refractory erosion. These phenomena give rise to an inefficient operation from both a process and an energy perspective.This investigation presents numerical and physical models of flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a slice model of an industrial PSC. For physical simulations, a 0.2-scale cold model was developed. Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The two- and three-dimensional numerical simulations of the three-phase system were carried out using volume of fluid (VOF) and realizable k- e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Both numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions employed in the investigation. Measurement of mass transfer characteristics conclusively indicated that fluid flow in the PSC is stratified. Both blowing configuration and volume of slag in the converters were found to have significant effects on mixing propagation, wave formation, and splashing.The splashing and wave motion in these converters are known to cause losses of metal/matte and potential production time due to the requirement for intermittent cleaning of the converter mouth, resulting in reduced process throughput. To prevent these losses and hence to increase process efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined, as well as lateral, blowing conditions. In comparison, the recent results of the combined blowing concept were found to be encouraging."

Jan 1, 2014

By J. Mulenshi, J. Rosenkranz, P. Khavari, S. C. Chelgani

The geometallurgical concept has mainly been applied to primary ore deposits, starting from ore characterisation to the economic optimisation of the mining operation. However, as primary ore resources are becoming depleted and lower in grade, alternative sources need to be explored and a question of adaptability of the geometallurgical approach to the secondary resource repositories arises. The particle size distribution, chemical and mineralogical compositions of the Smaltjärnen historical tungsten tailings from physical separation in Yxsjöberg, Sweden were studied using drill core samples collected from different locations within the tailings repository in order to assess the amenability of the tailings to reprocessing. The tailings are dominated by the –600 to +149 μm particle size fraction. This fraction contains most of the elements of interest (W, Cu, S, Sn, Zn, Be, Bi and F) hosted by scheelite, chalcopyrite, pyrrhotite, cassiterite, danalite (both Zn and Be), bismuthinite and fluorite, respectively. The particle size distribution and mineralogical composition vary across the repository, suggesting a possible existence of geometallurgical domains, which require further assessment to evaluate metallurgical performance. Keywords: Historical tailings, tungsten, scheelite, geometallurgy, characterisation, mineralogy, reprocessing

Jan 1, 2020

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By I. O. Ondicho, E. K. Mutinda, B. O. Alunda, E. Agyekum

Driven by the necessity to improve blast performance regarding fragment size distribution in limestone mines, this paper introduces the prediction and measurement of blast fragmentation distribution through the modified Kuz-Ram (MKR) and Kuznetsov-Cunningham-Ouchterlony (KCO) models. Precise prediction and measurement of rock fragmentation resulting from blasting play a critical role in hard rock ore extraction. This is due to the substantial influence of post-blast ore size distribution on the efficiency of all subsequent downstream rock handling and processing operations. Additionally, employing secondary breakage of boulders, when necessary, leads to an unjustified rise in production costs. In this paper, the MKR and KCO models were utilised to identify the most appropriate model for application in Bisil and Simba quarries situated in Kajiado County, Kenya. Split-Desktop was used for blast fragment measurement by processing digital images obtained after blasting and computing the fragment size distribution of the blasted rock. As per the investigation, the recorded percentages of boulders generated at the sites ranged from 7% to 12.3% for the Simba quarry and from 11.2% to 23.9% for the Bisil quarry, respectively. Regression, correlation, and root mean square error (RMSE) were employed as the primary performance indicators. The study concluded that KCO outperformed MKR in accurately predicting blast fragment sizes in the examined quarries.

Mar 5, 2025

By E. K. Mutinda, D. K. Maina, R. M. Kasomo, B. O. Alunda

Assessment of blast fragment size distribution is critical in mining operations because it is the initial step towards mineral extraction. Different empirical models and techniques are available for predicting and investigating the consequences of blasting, one of which is the Kuznetsov Cunningham-Ouchterlony (KCO) model. In this paper we summarize the advances in the empirical models from inception until now, and explore the improvements that have been made so far with particular emphasis is on the most recent KCO model. Utilization of the model and the errors that arise between expected and the actual outcomes are analysed. The results indicate that the KCO model remains useful for predicting the blast fragmentation at limestone mine sites, despite the availability of other advanced prediction models. It is also a valuable instrument for pre-surveying the impact of varying certain parameters of a blast plan.

Mar 1, 2021

By T. J. Otto, C. H. Cloete, T. Mkhatshwa, T. J. van Heerden

The value realised by an open pit mine depends on the quality and integrity of the mine planning process as well as the level of execution against these mine plans. When managing the execution against the mine plan, how well the mine plan is executed spatially, is of critical importance. The short-term mine plan is the plan that is physically executed on most open pit mines. At the same time, the spatial mine-to-plan compliance is typically reconciled against the annual business plan. Short-term mine planning, therefore, plays an important role in the effectiveness of the spatial mine-to-plan compliance reconciliation process by providing operational teams with detailed designs and schedules, while ensuring that mining execution is spatially aligned with the business plan. The Sishen open pit iron ore mine (Sishen) strives to continuously improve spatial compliance to the business plan. Sishen enhanced the role that short-term mine planning plays in enabling the forward-looking component of the spatial mine-to-plan compliance reconciliation process. The enhanced short-term mine planning process focuses on detailed tactical sequence designs per mining pushback, the health of value chain buffers, spatial plan-to-plan reconciliation, and the associated management routines. This led to improved spatial mine-to-plan compliance to the business plan from 71% to 94% over the four-year period from 2020 to 2023 inclusive. These results indicate that the application of short-term mine planning as part of an integrated spatial mine-to-plan compliance process at open pit mines can contribute positively to improving the level of spatial execution against the business plan. This paper presents the enhancements made to the short-term mine planning process, which other open pit mining operations can consider to improve spatial mine-to-plan compliance.

May 27, 2025

By B. Maybee, J. Venter, J. Wesseloo

The selection of open-pit slope angles involves high-value decisions with small changes in slope angle, often representing significant changes in net present value. The existing methods used to define design acceptance criteria have evolved from factor of safety to probability of failure (P[F]) to risk consequence to risk frontiers, which represents current state of the art. Current design acceptance measures are based on references to published tables representing the experience and judgement of their authors, who did not specify the purpose of the measures contained therein. As the purpose of the published design acceptance criteria is not specified (i.e., definite stability, marginal stability, optimization, etc.), such tables cannot be used to achieve optimum slope angles that maximize profitability. This paper develops a design acceptance criterion that maximizes profitability by defining a formulation for optimum risk that balances expected risk and reward. The model developed is titled the Mining Risk Model (MRM), and is applied to open-pit slope angle selection through an equation for optimum probability of downside (P[D]O) that balances the upside or opportunity, the P[F], and the downside impact. This formulation for optimum risk is unique, as many authors have presented objective functions for their risk models that can be optimized, but none of the sources reviewed contained a formulation for optimum risk. The MRM is sufficiently flexible to allow the design performance measure that drives P[F], and hence P[D]O, to be selected based on the intended goal. Furthermore, the essential information that must be known to quantify optimum risk is defined. This allows users to determine what information to collect for optimum risk decisions. A further benefit of the MRM is that slope angle decisions and pit shells can be ranked to select the best option, and a threshold is provided that separates acceptable from unacceptable decisions. Finally, the workflow and information required to determine optimum risk are presented.

Sep 9, 2024

By X. Zhang, Z. T. Yuan, C. Zhang, H. M. Zheng, X. M. Wang, L. X. Li, N. Li

In metal mines, comminution is commonly used to liberate minerals for subsequent mineral concentration processes, such as flotation, magnetic separation and gravity separation. However, ores are aggregates of valuable minerals and their disseminated gangue minerals, and these minerals exhibit diverse comminution behaviours. In carbonate-bearing iron ores, hematite, siderite, and quartz are the predominant minerals, of which hematite is the objective recoverable mineral. In this regard, the present study aimed to identify the imperfections in siderite minerals by X-ray computed tomography (XCT), and thus quantitatively characterise their size and shape in terms of Feret diameter and aspect ratio, as well as other parameters. XCT images indicated the protogenetic ubiquity of pores <5 μm in diameter and cracks of 7-8 μm inside siderite particles. In the ground product of artificially mixed siderite and hematite, siderite particles were smaller than hematite particles. Siderite particles had a larger surface area and greater surface roughness than hematite particles of the same volume, which was attributable to the intrinsic holes and cracks in siderite particles. This study provides an insight into the relationship between the inherent imperfections of minerals and their comminution properties. Keywords: Siderite; X-ray computed tomography; particle imperfections; grinding behaviour; sliming

Jan 1, 2020

By J. P. Kirsch

This paper sets out to clearly identify all elements that make up an effective furnace feed system. These are outlined and the more common types of technology are listed. These technologies all play an important role in the final delivery of all feed materials to the furnace.

Jan 1, 2008

By M. N. Mathabathe, A. S. Bolokang, C. W. Siyasiya, R. J. Mostert, G. Govender

The b-solidifying g-TiAl intermetallic alloys of nominal composition Ti-48Al (binary alloy), Ti-48Al-2Nb (ternary alloy), Ti-48Al-2Nb-0.7Cr (quaternary alloy), and Ti-48Al-2Nb-0.7Cr-0.3Si (quinary alloy) (in at.%) were developed. The materials produced were tensile tested at room temperature. The as-cast microstructures and fracture surfaces of the tensile tested specimens were examined using conventional metallographic methods. Microstructural examination indicated that the alloys were comprised of lamellar structures (a2+g) embedded in columnar dendritic cores in the as-cast condition. However, the quinary alloy contained a Ti5Si3 second phase. The alloys exhibited no detectable ductility during tensile deformation, indicating the brittleness of all the materials. The fracture surfaces revealed that the alloys failed by translamellar fracture with correspondingly few cleavage facets.

Apr 1, 2021

By K. Karaman

This study investigated the effect of surface roughness on Schmidt rebound hardness (RL). Four different test surfaces of rock samples were studied: natural, ground, cut surfaces, and core samples. There was significant variability of standard deviation based on the RL on the natural surface, which indicated high roughness of the rock surface, whereas surface polishing caused a significant decrease in standard deviation. ISRM and ASTM methods were compared to estimate unconfined compressive strength (UCS) for different testing surfaces. RL obtained from the cut surface was found to be more reliable than those obtained from other testing surfaces for the prediction of UCS; however, regression and ANOVA analyses revealed that the ISRM method gave a more accurate UCS estimation of rocks with highly rough surfaces. It was also shown that RL values obtained from a cut surface were significantly higher than those obtained from core samples. Therefore, a comparison between RL values obtained from core samples and cut surfaces was made based on previous studies. This study statistically showed that estimated UCS values are not statistically significant if Schmidt rebound tests are not performed on similar surfaces. In addition, the mineral grain sizes of the studied rocks, different testing surfaces compared with those in literature, and standard deviation from RL are evaluated and discussed. The Schmidt hammer technique is a rapid, inexpensive, and straightforward method for estimating UCS for preliminary assessment; however, roughness of the surface should be eliminated if variations are shown in the surface rebound hardness.

Apr 14, 2024

By H. Zhong, S. Wang, Q. Sun

The flotation performance of 2-(benzylthio)-acetohydroxamic acid (BTHA) to diaspore was first evaluated by micro-flotation tests. The adsorption mechanism was further investigated through adsorption experiments, molecular dynamics simulation, zeta potential and X-ray photoelectron spectroscopy (XPS). The results demonstrated that BTHA had a stronger ability to collect diaspore in comparison with another diaspore collector, benzohydroxamic acid (BHA), especially under the condition of weak alkalinity, the flotation recovery can reach 90%. The more negative interaction energy (ΔE) between BTHA and diaspore from molecular dynamics simulation results revealed that BTHA had an easier adsorption ablity onto diaspore than BHA, which matched with adsorption results. The zeta potential and XPS revealed that Al atoms might bond with -C(=O)NHOH by formation of Al-O bonds. Keywords: Diaspore, flotation; adsorption; 2-(benzylthio)-acetohydroxamic acid

Jan 1, 2020

By J. C. Steinhobel

Answers to questions raised at the Symposium on Trackless Mining in Metal Mines Questions by J. O. Steinhobel (1) When rubber-tyred equipment is used for the delivery of stores and items of equipment, how is heavy material-pipes, rails, timber support, ventilation columns, etc.-dealt with? Termination of Membership In accordance with By-Law 7.6.1. of the Constitution of the Institute, the names of the undermentioned members have been removed from the membership register.

Jan 9, 1973

By C. J. Badenhorst

The primary focus of management today is safety, or preventing negative, generally irreversible, events of acute duration. The outcomes of safety-related events are usually visible and can evoke strong emotions if the results are severe. Experts now see that occupational illness and disease also result in significant emotional and financial toll to workers, their families and communities, and to their employers. Effective health and safety management must include acknowledging the importance of occupational health hazards and the proportionate application of resources to address those issues. Improvement in workplace conditions and decrease or elimination of illness and disability are due to actions within the workplace and result from the implementation of risk prevention and control measures. However, success may only be visible months or years later and may require interventions that have to be maintained over prolonged periods. This demands continuous, co-ordinated effort to ensure sustainability of diverse occupational health programmes and the relevant management systems. Too often occupational health is not seen as being part of the general management of business, but rather the function of a medical practitioner somewhere off site in a clinic. Integration of occupational health management systems with other management systems within an organization is essential for its success.

Jan 1, 2004

By G. T. G. Emere

The Johannesburg Branch of The South African Institute of Mining and Metallurgy was officially inaugurated at a General Meeting held in Kelvin House on Monday, 18th January, 1988. In addition to nominating committee members, Mr G. T.G. Emere delivered a presentation on the Barbrook gold-mining project, which is currently in the development phase some 40 km east of Barberton.

Jan 1, 1988

By D. F. Malan, J. C. Esterhuyse

In this study we explore the use of a novel numerical modelling approach to study the effect of pillar reinforcement on pillar stability. Case studies in the literature indicate that tendons, strapping of the pillars, and shotcrete or thin spray-on liners are commonly used to reinforce pillars. No clear methodology exists to select the type of support or to design the capacity of the support required, however. This has led to ongoing collapses in some mines in spite of heavy support being used to reinforce unstable pillars. A limit equilibrium model with confinement on the edge of the pillar was used to simulate the interaction of the support with the failing pillar. The model correctly predicts that an increase in confinement will lead to a decrease in the extent of pillar failure. As the displacement discontinuity boundary element method allows for the efficient solution of largescale bord-and-pillar layouts, the effect of pillar confinement can now be studied on a mine-wide scale. Accurate calibration of the limit equilibrium model is, however, required before this method can be used for the design of effective pillar support.

May 3, 2023

By S. Jeon, J. Kim, H. Lee

Though the importance of the engineering rock mass properties such as deformation modulus, cohesion and friction angle is emphasized, the researches on the reliability of these values are rarely performed. By using modified Takagi-Sugeno (TS) fuzzy inference system, a fuzzy model was developed based on the data obtained from domestic tunnel construction sites, and the ability of prediction was compared with the empirical equations conveniently used for estimating these values, which finds that fuzzy model is better than empirical equation. Sufficiently large database, however, is required for training the fuzzy model for more accurate prediction. Obwohl die Wichtigkeit der technischen Eigentümer der Felsenmassen wie zum Beispiel Verformungsmodulus, Bindekraft und Reibungswinkel betont werden, wird die Forschung auf der Zuverläßigkeit dieser Werte selten durchgeführt. Mit modifiziertem Takagi Sugenos (TS) Flaumigenschlußsystem wird die Flaumigenmodelle von den Daten, die von inländischen Tunnelbaustellen erhalten werden, entwickelt. Zum Schätzen dieser Werte ist es viel günstig, Flaumigenmodell zu benutzen, als zu adoptieren die empirische Gleichung für die Fähigkeit der Voraussage. Genügende große Datenbank wird aber zum Ausbilden flaumigen Modells für genauere Voraussage erfordert. Quoique l&apos;importance sur la caractéristique d&apos;ingénierie de la masse de roche comme le module de déformation, la cohésion et l&apos;angle de friction, soit soulignée, la recherche sur la confiance de ces valeurs est rarement effectuée. Avec le système modifié de Takagi-Sugeno(TS) fuzzy inférence, le nouveau modèle fuzzy s&apos;est développé. Après avoir estimé sa valeur, nous pouvons savoir que ce modèle fuzzy, basé sur les données venant du chantier de construction de tunnel national, est mieux que l&apos;équaton empirique. Pourtant plus de données de base sont indispensables pour produire le modèle fuzzy plus précis.

Jan 1, 2003