Search Documents

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By J. S. C. Joubert

The Koidu Kimberlite Project is situated in the Kono District of Sierra Leone, approximately 330 km east of the capital city, Freetown. The mining lease area is 4 km2 and comprises 2 kimberlite pipes, 4 dyke zones and a number of blows off the dykes. Koidu Holdings established on the property and began dewatering and the removal of silt from the existing 30 m excavation of the No.1 Pipe in 2003. While the original planning for the pipes included conventional open pit operations, mitigating factors such as the proximity of the town, the presence of houses close to the perimeter of the pipe, the size of the pipe and the planned open pit depth with relevant stripping ratios, as well as uncertainties on the grades in respect of an underground operation, lent itself to the vertical pit concept. The vertical pit was established using an A-frame headgear for the hoisting arrangement, with sidewall support comprising a combination of 20 m and 40 m long cable anchors, rock bolts, wire mesh and pneumatically applied concrete. The pit reached steady state production in January 2007 and produced some 26,000 tonnes of head feed per month until August 2007 when mining reached a depth of 74 m below the pit collar (approximately 126 m below surface). Mining was suspended following a sidewall failure that disrupted operations. Now that the grades in No.1 Pipe have been validated, focus has been switched to an underground operation taking account of both No. 1 Pipe and No. 2 Pipe. While the mining costs for the vertical pit have been higher than for a conventional open pit, the concept did circumvent the social implications, the issue of grade consistency and diamond value at depth, as well as providing the time frame to carry out a full underground mining study.

Jan 1, 2008

By J. Sepulveda

"Despite the recognized influence of product fineness on line capacity and downstream process performance, few mineral concentrators today use particle size measurement of the final product in automatic control applications for particle size. ‘Near-line’ particle size instrumentation has existed for decades and is utilized in modern concentrators, but low availability and measurement frequency, due to problems with slurry sampling and transport systems, make these technologies unreliable for use in automatic control. An innovative technology for real-time particle size measurement on individual hydrocyclones, named CYCLONEtrac™ PST (particle size tracking), has been developed by CiDRA Minerals Processing, and proven in commercial installations, demonstrating near 100% availability with minimal maintenance requirements, thus overcoming the limitations of previous technologies. Potential stakeholders require convincing, reliable information regarding the economic value delivered by automatic grind control projects. In this paper we present a methodology for estimating such value with the CYCLONEtrac™ PST technology, and demonstrate unique opportunities to improve process stability and performance. Based on actual plant data accumulated over time, the evaluation approach assesses and highlights the significant potential process improvement that can be expected with the particle size tracking technology. As an extension of previous work, in this paper we present the key operating criteria for optimizing the production of valuable metals and increase mill throughput by identifying the optimal grind size. As this requires operating closer to the process boundaries, accurate real-time particle size measurements, such as those provided by the CYCLONEtrac™ PST system, become essential for achieving the maximum potential value from every operation. For further illustration, data from three different copper plants is compared.Introduction Owners and operators of mineral concentrators constantly search for the most economically attractive way to increase the output of valuable metal. A logical approach is to identify a key parameter that has the greatest impact on the performance of multiple stages of the process and then use a holistic analysis methodology to determine how this key parameter can be controlled to optimize the final output.Particle size is widely recognized as such a key parameter; however, very few concentrators today use real-time particle size measurements for automatic control of the final product size due, to a large extent, to the inherent limitations of existing technologies. ‘Near-line’ particle size measurement instrumentation, which has been used for decades, typically suffers from low availability because the fundamental measurement technologies were developed for other, less demanding industries and then adapted to the harsh environment of the typical mineral concentration process. An outline of the key differences among the available technologies used for particle size measurement in comminution circuits has been completed in previous work, and plant data has proven the benefits of measurements on individual cyclones – something that, until now, has not been possible (Cirulis, 2017)."

Nov 1, 2018

Professor R.F. Sandenbergh matriculated at Germiston Afrikaans High School, and then he obtained the degrees of B.Eng. (Chem.) in 1972, M.Eng. (Chem.) in 1975, and D.Eng. (Met.) in 1983-all from the University of Pretoria. Mr J.A.D. Britz matriculated in 1958 at the Roodepoort Hoerskool, and joined the mining industry in 1959 as a student mine official at the Rand Mines Training Centre. Mr J.A. Cruise matriculated at Durban High School and joined Union Corporation as a Learner Official in 1962. He was awarded a scholarship to read for B.Sc. and M.Sc. degrees in mining engineering at the University of the Witwatersrand

Jan 1, 1990

By A. S. Ratnayake, H. C. S. Subasinghe

In this study, we review the role of mechanical activation in the pyrometallurgical, hydrometallurgical, and electrometallurgical processing of titanium feedstock. Mechanical activation has been shown to decrease the activation energy of chemical reactions, thus enhancing process efficiency and product quality by reducing processing time and energy consumption. Pyrometallurgical processing is energy-intensive and time-consuming. Hydrometallurgy is costly, requires high-grade feed material, and generates toxic waste. Waste generation and process complexity are the major drawbacks of electrometallurgy and solvent extraction. Bioleaching via a mechanically activated pyrometallurgical process can be identified as an alternative method, but the lengthy processing time is the major disadvantage. Mechanically activated titanium concentrate can be used in a finely tuned combined metallurgical process to overcome the challenges and drawbacks in these technologies.

Aug 3, 2023

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By E. Saari, B. Musuku, K. Jansson

The quality of the concentrator plant process water is crucial for high performing mineral flotation circuits. Significant metal recovery and concentrate grade losses have been noticed particularly in more closed water loops. The recovery and quality losses have started to emerge mainly with decreased freshwater usage and because of changes in tailings management towards tailings thickening, paste, or dry stacking. These changes result in shorter, closed water loops with a rapid build-up of harmful components with negative impact on the beneficiation process. Consequently, water quality has a direct link to decreased product value and sales returns. Complete cleaning or water blending might not be the right way to achieve high recovery and high-quality products. Instead, the key is to understand what kind of water qualities are needed for the flotation of specific minerals. In this study harmful substances in various plant water streams were removed and/or modified by pilot-scale dissolved air flotation. Batch-scale mineral flotation tests with the untreated and treated water were then performed by using fresh ore samples and the plant’s own laboratory flotation procedure. The results indicate that because of dissolved air flotation, the mineral flotation recoveries were enhanced by 1‒3.3%. Keywords: Mineral recovery, metal recovery, mineral quality, process water, concentrator, beneficiation, mineral processing, flotation, process water treatment

Jan 1, 2020

By E. J. Y., G. J. McLachlan, E. Amini, Koha

Inferring individual component flotation rates from recovery-time data of ore complexes is important in optimising and designing minerals processing plants. However, existing two-component first-order flotation models are computationally intensive to solve using conventional non-linear least squares regression. In this paper, a Convolutional Neural Network (CNN) is used to approximate the inverse function which predicts the two-component first-order model parameters using recovery-time data. This paper compares the accuracy and computation speed of the proposed CNN against traditional non-linear least squares regression on 1 million generated data based on a known two-component firstorder kinetic model. It is shown that using a CNN is possible to approximate the inverse function for the non-invertible two-component model with recovery-time as an input matrix for convolution operations. The CNN method is 450 times faster to compute than the Trust-Region (TR) non-linear least squares regression algorithm. However, the CNN model is less accurate compared to the TR algorithm overall. Keywords: Flotation kinetics, convolutional neural network, inverse problem, modelling and simulations

Jan 1, 2020

By J. Uys, P. J. Mokganya, J. Olwagen, R. C. W. Webber-Youngman

This article discusses the critical role of leadership in the technology adoption process within organizations, particularly in industries like mining, where innovation is essential for maintaining competitiveness and operational efficiency. It highlights the limitations of traditional technology adoption models, such as the Technology Acceptance Model (TAM), Diffusion of Innovations (DOI), and Unified Theory of Acceptance and Use of Technology (UTAUT), which focus on individual factors and overlook the strategic and organizational roles of leadership. The study proposes the Ambidextrous Leadership-Technology Adoption (ALTA) model, which integrates leadership styles such as transformational, transactional, adaptive, and ambidextrous leadership into the technology adoption process. The model emphasizes the balance between exploration (fostering innovation) and exploitation (ensuring operational efficiency). The findings suggest that transformational leadership fosters innovation by encouraging risk-taking and creativity, while transactional leadership ensures efficient technology integration. The article also identifies key barriers to technology adoption, such as organizational resistance to change, which can be mitigated through adaptive leadership that addresses employee concerns. The research emphasizes the importance of a supportive organizational culture and cross-functional collaboration, which are essential for successful technology adoption. The study concludes by offering practical recommendations for leaders to foster a culture of innovation, manage resistance, and balance short-term efficiency with long-term technological advancement.

Nov 27, 2024

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By A. Golder, S. P. Dandapat, I. Roy

One of the consequences of large-scale opencast mining for coal is the disposal of an enormous volume of overburden material that needs to be removed. With the enlargement of opencast mines and associated high stripping ratios, the volume of overburden extraction is rising. Overburden from the initial mine cut has to be necessarily dumped outside the mining area until enough void is created inside the mine for back-filling operations. The quantity of overburden placed outside the mining area normally varies from 10% to 30% of the total overburden removal. The stability of these dumps placed outside the mining area is of prime importance from the point of view of smooth operations of the mines and safety of persons in and around the dumping area. Owing to increasing pressure on land use, mine operators do not have any other option other than to place the waste dumps very near to the surface edge of the pit, which may lead to failure of the topsoil benches of the working pit. This study identified major controlling parameters that influence a stable but economic combination of height and slope angle of external dumps located close to the edge of an open coal pit.

Nov 27, 2024

"Chairman: Professor J. de V. Lambrechts Rapporteur: Mr R. HempPapers:Computer-aided design of a flash smelting installation by M. A. T. Cocquerel, R. T. Gates and L. A. GreenPlanning of mine ventilation by E. U. Reuther and A. DohrnenCoal mine ventilation systems in the U.S.A. by R. Stefanko and R. V. Ramani Heat flow models in ventilation planning by A. J. Dickson and A. M. StarfieldThe first of the papers in the session dealt with a flash smelter installation, while the remaining three papers dealt with mine ventilation. In view of this the Chairman proposed that the paper on flash smelting be introduced and discussed first, after which the remaining three papers would be introduced followed by discussion on all three.Dr Cocquerel, who presented the first paper, used some typical flow diagrams to illustrate the process and stated that the program considered only steady-state operations and did not take into account the dynamical changes. Subjective judgment was necessary for the preparation of input data and some degree of user appreciation was required.Dr Cocquerel said that no work bad yet been done on an optimization program, but that this was being considered. Such a program would require a large amount of physical and chemical data which were not yet available. The variables to be optimized were the energy and material consumptions and the loss of metal in the slag.The Chairman opened the discussion by asking Dr Cocquerel if he could give a brief description of the flash smelting process for the benefit of those not familiar with the subject. Dr Coquerel replied that in the Outokumpu process con¬centrates were injected directly into the furnace, and that the process was somewhat analogous to flash distillation or evaporation processes, but was perhaps closer to the burning of pulverized fuel.The process had two distinct advantages. First, the heat evolved in the smelting reaction was used to heat the furnace, which resulted in less fuel consumption, and, second, the effluent gases were cheaper to treat than the effluent gases from other pyrometallurgical processes. This was important particularly in view of the current interest in pollution problems.Mr P. Marais thought that the authors had done themselves an injustice by not including details of the very complex processes taking place in the furnace."

Jan 1, 2014

By T. Nesane, S. S. Mnyakeni-Moleele, L. C. Murulana

The effectiveness of two synthesized ionic liquids, 1-(benzyloxy)-1-oxopropan-2-aminium 4-methylbenzenesulfonate (1-BOPAMS) and 4-(benzyloxy)-4-oxobutan-1-aminium 4-methylbenzenesulfonate (4-BOBAMS), were evaluated for mild steel corrosion inhibition in 1.0 M hydro-chloric acid solution, using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and gravimetric techniques. Organic moieties responsible for the adsorption process on mild steel surface were investigated using Fourier transform infrared spectroscopy (FTIR). Gravimetric analysis revealed that the inhibition efficiency of 1-BOPAMS and 4-BOBAMS increased with concentration, with maximum inhibition values of 90.32% and 97.91%, respectively, at the highest concentration of the inhibitors. Gibbs free energy (ΔG°ads) values indicated a strong interaction between the mild steel surface and the molecules of the ionic liquids, and that the adsorption process was spontaneous. These values also show that the inhibitive nature of ionic liquids against mild steel corrosion is caused by a mixedtype of adsorption film formed on the steel surface. The Langmuir adsorption isotherm was used to describe the adsorption of ionic liquid molecules onto the mild steel surface. Polarization curves showed that 1-BOPAMS and 4-BOBAMS have a similar effect on both the anodic and cathodic half-reactions, indicating that they prevent the dissolution of mild steel through both physical and chemical process. Nyquist plots were defined by incomplete semicircle capacitive loops, showing that the charge transfer mechanism controls the corrosion of mild steel in acidic solution.

Apr 1, 2021

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By D. M. Poulter, J. N. Brooke, P. H. Williams

"The complexity of the mining and metallurgical operations of Nchanga Consolidated Copper Mines, Limited, has made it necessary to use computer-assisted planning techniques in order to maximize copper production and marginal contribution to profit. The most successful of the Group Production Scheduling systems utilized linear programming to optimize the concentrate routing only. This third-generation system was commissioned in March, 1968.It bad become necessary by March, 1970, to expand the long-term planning activities and to take into account new mines and new concentrate treatment schemes. Technical difficulties and manpower limitations made it impossible to expand the third-generation system, and it was decided to construct a new Group Production Scheduling system using only linear programming.The plant models in the new fourth-generation system are based on data available from the monthly reports of the metallurgical plants. The models consist of mass balances and empirical relationships. Matrix coefficient assignment and management reports are produced using a Report Generator Language designed for linear programming data files. The development of this system is an example of a user application of a system package."

Jan 1, 2014

By L. M. Tavares, H. A. Petit, P. P. Cavalcanti

Iron ore pellets experience degradation during handling due low energy impacts and stresses. These impacts lead to volume or surface breakage of the pellets, creating fine particles that accumulate along the process. Some of the particles are in contact with the air and are dragged as dust into the workplace or into the atmosphere. The aerodynamic size of the particles allows them to be potentially inhaled by the workers or to be carried to nearby communities. Dust emission becomes critical at specific locations, such as transfer chutes and stockpiles. This work models the dust generation that occurs in an iron ore pellet stockyard using a methodology that combines experiments to quantify the degradation of the pellets to mathematical modelling of the dust emission mechanisms in the stockyard. First, laboratory tests were used to characterise the amount of mass and the particle size distribution of the dust generated by degradation under controlled conditions. Second, the flow over a stockpile of an iron ore pellet company was simulated with the aid of computational fluid dynamics (CFD) simulations. Third, semiempirical equations linked the data generated by simulations and laboratory tests to estimate the dust emission in the stockyard. Finally, results were validated with measured field data, obtained with a novel online measurement tool. Results suggest that the approach is able to predict dust emission with sufficient accuracy and can be used for further implementation in the management of operations and decision making in order to reduce the environmental impact of the process. Keywords: Iron ore pellets, abrasion, dust emission, mathematical modelling

Jan 1, 2020

By L. Hermansson

Trackless mining at LKAB, Sweden by L HERMANSSON (Visitor) Because the usual means of transporting men and material to the working sites was time-wasting and uneconomical, inclined subways were installed in the Kiirunavaara Mine that permitted the access of rubber-wheeled vehicles to all underground working sites. Men and material could now be transported direct to the working site with no reloading. An increase of 8 to 12 per cent in underground productivity has been obtained by the use of this new transportation system. Rubber-wheeled vehicles are also used in development, production drilling, and loading. In December 1958, the management of the Luossavaara Mine decided to cut the costs of waste-rock haulage. The system of waste transport was the conventional one of shuttle car, rail haulage, and skip hoisting. After consideration of other methods, it was decided to re-equip the mine completely for a system of trackless transport. Results show that mining costs per ton of ore were reduced by 27 per cent, and mining costs per ton of waste were reduced by a spectacular 80 per cent. The new system has proved to be more flexible, and ore grading has been simplified since there is no longer any mixing in ore passes and chutes.

By Q. Zhang, X. C. Wang, X. Q. Ao

The flotation separation of apatite and calcium-bearing gangue minerals (dolomite and calcite) has always been a problem in phosphate ore mineral processing research. The crystal structure and surface properties of minerals have an important influence on their floatability. In this paper, the theoretical and comparative analysis of the crystal structure and surface electronic properties of apatite, dolomite and calcite were carried out using the first principle calculation based on density functional theory. As a supplement and validation, the surface wettability of three minerals under different flotation conditions were compared and analysed by contact angle test. The results theoretically revealed that the three calcium-bearing mineral surfaces have similar surface electronic properties and thus exhibit similar floatability. In the flotation process, the anion difference between apatite and carbonate gangue should be fully utilised, and the minerals can be separated only after surface modification by flotation reagent. The contact angle test shows that phosphate and carbonate can be separated by using anion flotation collector after surface modification with acid. It is expected that this research is of interest for understanding the surface structure and electronic properties of apatite and carbonate gangue minerals and providing the theoretical basis for surface interaction. Keywords: Apatite, dolomite, calcite, surface structure, electronic property, density functional theory

Jan 1, 2020

By S. Chatterjee, F. Suparno, A. Paithankar

Estimating reserves and quantifying resources stand as pivotal and intricate endeavours within the realm of coal mining operations. Intricate geological formations compound the challenges in resource estimation, thereby complicating reserve calculations. The uncertainties tied to geological attributes of coal, encompassing parameters like tonnage and coal quality, wield significant sway over resource and reserve computations within coal mines. This research delves into the domain of geological uncertainties, with a specific focus on calorific value, aiming to numerically characterise resources and reserves within an open-pit coal mine situated in Indonesia. To quantify resources, the coal seam geometry underwent simulation via a multipoint geostatistical technique known as single normal equation simulation. A geologically established coal seam served as the training image for generating 20 equiprobable coal models. To simulate CV, 50 realisations were generated for each simulated coal seam, utilising sequential Gaussian simulation. Deviations of the simulated coal seams ranged from -0.07% to 5.48% in comparison to the training image. The CV simulation yielded an average value of 5,920.29 kcal/kg, accompanied by a standard deviation of 586.54 kcal/kg. However, the average CV spanned from 5,305.26 kcal/kg to 6,526.55 kcal/kg across diverse simulations. For reserve calculation within the context of geological uncertainties, an algorithm rooted in maximum flow graph theory was employed to construct the ultimate pit for the coal mine. Within this final pit, the average stripping ratio was 1.62, coupled with a CV value of 6,019.66 kcal/kg. When juxtaposed with the deterministic model, the findings underscore that the stochastic ultimate pit delineates a more expansive excavation, accompanied by a heightened undiscounted cash flow.

Oct 2, 2025

1. Book review Technology of metal powders- recent developments, edited by L. H. Yaverbaum. New Jersey, Noyes Data Corporation, 1980. 400 pp. (Reviewer: B. K. Loveday) 2. New books The use of microprocessors, by M. Aumiaux. New York, Wiley, 1980. 176 pp. $25,50. Aluminium smelter technology, a pure and applied approach, by K. Grojtheim and B. J. Welch. Diisseldorf, Aluminium-Verlag GmbH (P.O. Box 1207, D-4000, Federal Republic of Germany). 146 pp. DM48. Coal-bridge to the future. New York, Harper & Row, 1980. $35. System modeling and response.. theoretical and experimental approaches, by O. Doebelin. New York, Wiley, 1980. 576 pp. $26. Environmental and climatic impact of coal utilization, edited by J. J. Singh and A. Deepak. New York, Academic Press, 1980. 646 pp. $39,50. Proceedings of the Third European Conference on Mixing, York, England, April 1979, edited by H. S. Stephens and C. A. Stapleton. BHRA Fluid Engineering (Cranfield, Bedford Mk43 OAJ, U.K.), 1980. 2 volumes. 500 pp. $50. Lignite technology, edited by P. Nowacki. New Jersey, Noyes Data Corporation, 1980. 228 pp. $42. The application of rock mechanics to cut-and jill mining. London, Institution of Mining and Metallurgy, 1980. Papers presented at the Fifth International Symposium on Jet Cutting Technology, Hanover, Federal Republic of Germany, June 1980, edited by H. S. Stephens and B. Jawis. BHRA Fluid Engineering (Cranfield, Bedford Mk 43 OAJ, U.K.), 1980. 438 pp. £38. World coal resources.. methods of assessment and results, by G. Fettweis. Amsterdam, Elsevier, 1979. 425 pp. $80,50. Geophysical and geochemical techniques for exploration of hydrocarbons and minerals, edited by M. Sittig. New Jersey, Noyes Data Corporation, 1980. 300 pp. $40. Financial Times mining international year book 1980. Longman Group Ltd (Periodicals and Directories Division, Longman House, Burnt Mill, Harlow, Essex CM20 2JE, England). £24 surface, £34 airmail. National Symposium on the Availability of Strategic Minerals, edited by M. J. Jones. London, Institution of Mining and Metallurgy, 1980. 109 pp. 3. NIM reports Report No. 1941 The recovery of chromite and platinum from the UG-2 Upper Chromitite Layer .of the Bushveld Complex at the Pandora Mine (first published 10th Mar., 1978). Report No. .2012 A mineralogical investigation of borehole cores from the Trompsburg Complex (first published 6th Apr., 1979). Report No. 2038 The leaching of sphalerite in acidic ferric sulphate media in the absence of elemental oxygen. Report No. 2052 An investigation of the impurities in native gold by neutron-activation analysis. Report No. 2056 The mineralogy and geochemistry of the copper, lead, and zinc sulphides of the Otavi Mountainland. Report No. 2058 A n elementary introduction to image analysis - a new field of interest at the National Institute for Metallurgy. Report No. 2059 Distributed computer control of industrial processes. Report No. 2060 The analysis, by atomic-absorption spectrophotometry, of activated charcoal.

Jan 1, 1980