Search Documents

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V, Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

By S. Sekhar, S. Bhargava, A. K. Godugu, J. L. Porathur

Cemented backfilling has enabled underground hard rock mines to extract orebodies more safely with improved ore recovery. It is important to estimate the minimum required strength parameters for a backfill mix by optimizing the binder percentage to enable cost-effective and safe stoping operations. We conducted three-dimensional numerical modelling to study the effect of various stoping parameters on the stability of a free-standing backfill wall. A Mohr-Coulomb material model was used for the backfill material and the rock-fill interface. A strength reduction technique, excluding friction angle, was employed to arrive at a minimum stable strength value for the backfill. For a given combination of strength values, the stability state of the backfill wall could be demarcated using a displacement and yield zone tracking method. The numerical modelling results are compared to some earlier theoretical models. From the simulations, a predictive equation is developed to predict the required strength parameters for a backfill mix to ensure a stable free-standing wall. Examples are given of the successful use of the predictive equation at some underground hard rock mine sites in India.

May 2, 2022

By X. W. Pan

It has been found that the MnO content of a slag decreases sharply when direct current is applied to a 1T1£tal-Slagsystem consisting of liquid Mn-Si-Ccsat metals and MnO-SiO2-CaO-AI203 slag in graphite crucibles. This paper reports a preliminary investigation into the electrochemical effects of direct current on the metal-slag system, the silicon content of the metals, and the MnO content of the slag. The results show that, when a direct current of 7 A is maintained, the MnO content of a metal containing 10 to 11 per cent silicon by weight is reduced rapidly from 26,5 to 17,2 per cent by weight. This reduction seems to proceed further when the process is continued. When the direct current and the voltage are kept constant at TA and 4 V respectively, the MnO content of a metal containing 1 to 2 per cent silicon by weight is reduced to 1 from 25 per cent by weight, which results in a manganese yield of 96 per cent.

Jan 1, 1995

By F. Yang, T. Pan, T. Zhao, Z. Shao, D. Zuo

In this paper, the development and applications of robot technique is summarized, and the status and developing direction of China coal mine robotics. A description of the research meaning, frame and key technology of underground salvage robot is given. Keywords: coal mine, robot, special robot, salvage robot.

Jan 1, 2003

By T van Zyl

Some standards are being used by the corrosion industry on a daily basis. This talk will cover how a standard comes into existence, the different types of standards and the voluntary/ compulsory nature of different standards. The maintenance of standards is discussed This talk also looks at how standards should be referenced, what reference to the mark scheme can be made and which national and international standards might be of value in the corrosion industry.

Jan 1, 2006

By A. E. Voigt

Iron ore samples representing the input and output of several jigging experiments were analysed to determine the effect of particle size, shape, and density on jigging performance. Traditionally, the manual measurement of the size and shape of individual particles is very tedious and prone to inaccuracies and inconsistencies. Using a novel multi-view imaging technique the 3-dimensional representations of each particle in the sample was determined. From this representation several size and shape measurements were extracted, and these were correlated with the individual particle density measurements. A rigorous investigation into the confidence associated with density and the size and shape features as a function of sample size was conducted, thus allowing the significance of correlations in the data to be determined. The jig?s performance was seen to be clearly sensitive to density and markedly so to particle size, while the results for shape indicated the need for continued work in the definition of particle shape.

Jan 1, 2012

By A. Tello

Variography was introduced by Dr. Pierre Gy to monitor a process, in the sixties. Later on, Francis Pitard extended this concept, building a complete system of variographic controls for different applications. Nevertheless, the existence of information about its use as a way to effectively control plants has been limited. There are infinite areas where variography and chronostatistics can be used. In this paper, two different cases related to gold and silver recovery, through well known but complex metallurgical routes are studied. The use of effective management of process variability software (EMPV) has shown to be a suitable solution to clarify problems at the plant and, consequently, a solution to the encountered problems has been proposed. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in depth way. Once the ore has been extracted from the mine, sampling is necessary at each sequence of the metallurgical process involved. As a first example, leaching of the ore with cyanide in agitated tanks is another case of a complex metallurgy. The aim of the process is to know about residual values in the tailings in order to optimize process. As a second example, leaching of gold and silver in ore heaps, has to be optimized in terms of time, reagents consumption and, of course, in predicting a reasonable recovery. This last issue appears to be crucial. After cyanide leaching at the heaps, a carbon in columns process is involved, where there are a series of carbon loaded columns that are submitted to a dynamic process of load and unload, to finally deliver an enriched solution to the precious metal electrowinning plant. In both cases, variography has been a good approach to show metallurgists ways to improve the operation.

Jan 1, 2009

By M. Rossouw

The paper sets out the strategic importance of South Africa?s mining and minerals sector to the national economy. It relates how inexorable and accelerating urbanization and industrialization in emerging markets, especially in China and India, will translate into sustained demand for the minerals that South and southern Africa have in abundance. It warns that while countries buying raw materials from South Africa use these inputs as the basis on which to build value-added, employment-creating industries, South Africa is failing to exploit the economic benefits inherent in its mineral wealth, exacerbating its shortage of skills.

Jan 1, 2011

By C. Musingwini, G. Njowa, M. Burnett, C. C. Birch

From 2022 to 2040, the global demand for mineral commodities is projected to increase by fourfold to six-fold, largely due to traditional drivers such as population growth and urbanisation compounded by the adoption of decarbonisation technologies that are more mineral intensive than fossil fuel technologies. To meet this projected demand, companies operating in the minerals industry should accelerate the development of mineral projects. Since most of the companies generally operate in multiple geographical, regulatory or legislative jurisdictions, it is critical that the information on Mineral Resources and Mineral Reserves they report on in the public domain should be comparable and consistent across different jurisdictions. The Committee for Mineral Reserves International Reporting Standards fosters alignment of national and regional mineral reporting codes through an internationally accepted template that creates common technical understanding of definitions, classification, estimation processes and the Public Reporting of Exploration Results, Mineral Resources, and Mineral Reserves. The Committee for Mineral Reserves International Reporting Standards Template-based codes guide reporting at respective national and regional levels. Since mine planning is critical in the conversion of mineral resources to mineral reserves, a shared technical understanding should aid comparability of mine planning results. However, differences persist in the way mine planning results are reported. Unlike most previous studies, which have primarily focused on comparing mineral reporting codes, this paper updates and extends such comparisons by exploring how similarities or differences in reporting should influence the mine planning process. It also recommends some principle and process changes to assist mine planning professionals to improve consistency and comparability in reporting mine planning results.

Mar 30, 2026

By K. L. Riemer

The West Wits Line first began yielding gold in the mid-1930s and is among South Africa's leading gold-producing areas. Gold mining operations are carried out amidst the occurrence of seismic events which cause both damage to underground excavations and injury and loss of life to production personnel. The feasibility of establishing a system to minotor the seismicity on all the Gold Fields mines was investigated during the early 1980s. This led to the establishment of a centralized seismic network in 1981. The system was structured around three major objectives. It uses Perkin Elmer (now Concurrent Computer Corporation) 16 and 32 bit mini-computers. The hardware in use at both the central and remote sites is outlined, giving a good insight into the role of computers in the system. The system software reveals the fast flow of data through the network; it can be divided into three categories: (1) data logging and transmission - remote sites, (2) data capture and communications - central site, (3) applications and research - central site. Several examples are given which show how the system is measuring up to its objectives. These case studies also indicate how the computers are effective in representing the seismic data collected. It is concluded that the use of computers enables the pin-pointing of seismic events on the West Wits Line within about 3 -4 minutes of their occurrence. The choice of hardware is largely dependent on the objectives of system, and the Gold Fields Network has chosen mini-computers because of the speed of communication and the large amount of data and storage required for research applications.

Jan 1, 1987

By A. Çelik

Wheel loaders are widely used in many sectors due to their mobility, operational flexibility, and low costs. The literature is mainly focused on improving the hydraulic, mechanical, and electronic subsystems of these machines in terms of efficiency or developing strategies for controlling these systems. In this study, the effects of the loader operator and different working conditions on the loading performance were investigated. The study was carried out at the Can Lignite Enterprise (CLI), which is a major coal producer in Turkey. In the study, which lasted approximately four months, a total of 808 measurements were performed to investigate seven different scenarios. The effect of a single parameter on loading performance was investigated in the first six scenarios. The results showed that the biggest impact on loading performance was caused by the operator's experience with 63.4%. On the other hand, the worst and most ideal working conditions determined from the first six scenarios were tested in the seventh scenario. It was tested as a script. The test results showed that the loading performance was 285.5% more effective under the most ideal operating conditions compared to the worst operating conditions. In addition, in the study, the loading performances of five loaders with four different capacities were examined in terms of energy efficiency and it was determined that the Kawasaki 115 work machine, which has a higher model and lower engine operating hours, was more advantageous. In the study, various suggestions were developed in parallel with the research results. The most prominent and easiest to implement of these suggestions is related to the selection of the loader operator.

Nov 27, 2024

By A. M. Croll

The efforts to mechanize narrow reef tabular orebodies unique to this country, are not new. They began in the early 1900s and have over the last century seen varied rates of progress and success. Efforts to mechanize with the use of scraper winches can be regarded as a success. The scraper winch replaced the hand lashing of ore and development waste into hoppers. The initiatives by Anglo Gold and the then JCI to implement trackless mining equipment into these environments had limited success but in general were looked upon as a failure?at least this is the perception. The Chamber of Mines Research Organization (COMRO) in conjunction with various mining houses tried to make a success of the impact ripper. Diamond wire cutting of the stope face is another, which has been tried and tested. The use of high-pressure water to cut rock has also been trialed. These attempts, amongst others, are just a few of the efforts that have not been successful in the quest to make life at the face safer, more productive and easier for our employees. Against the backdrop of an emerging South Africa, the associated high expectations of historically disadvantaged people within the country, a strong rand, demands for better safety, lower cost of production and more efficient operations, mechanization has the chance to make a difference to Anglo Platinum?s business. Mechanization has certainly changed the way other commodities such as coal, base metals and diamonds are won from the earth. Mining?s image is still one of people crawling around in stopes?a dirty, ?low-tech? business. Anglo Platinum?s latest journey to mechanize its underground operations began in earnest in1998 and has enjoyed some successes and failures. The opportunity to change the way mining is done within the company is there. Technologies are evolving, and the implementation of mechanization can certainly assist with the achievement of the goals referred to above. When mechanization commenced, targets were set for the company to achieve but these have been revised in the light of recent events relating to the strengthening rand and a slow-down in expansion plans. However, the intent to mechanize appropriately in Anglo Platinum still exists.

Jan 1, 2004

By P. Saayman

The mining industry has much potential for automation. A great deal of work has been done on this subject and is still ongoing. With automation comes the possibility for optimization, because more information is available and actions can be repeated with more accuracy. This paper looks at possible solutions to the problem of optimizing the autonomous vehicle dispatch system in an underground mine. Possible optimization strategies are evaluated using a simulated environment. The majority of the results indicate that improvements on current methods are possible. Keywords: mining automation, simulation, vehicles, dispatching strategy, optimization.

Jan 1, 2006

By S-J. Park

When evaluating mining investment opportunities, one should consider the risks associated with mineral exploration and development. These are commonly classified as technical, economic, and political risks, and are accounted for in the investment decision by changing the discount rate. Thus, a company may use different discount rates associated with varying risks in order to compensate for the variability of success. The discount rate has a tremendous effect on the economic evaluation of mineral projects. Even when all other factors used as inputs for calculating the NPV (net present value) are equal, the project under consideration may be accepted or rejected depending upon the discount rate. Determining a realistic discount rate for a given project is therefore the most difficult and important aspect of cash flow analysis. It should be determined with the consideration of proper technical, economic, and political conditions surrounding the specific project undergoing economic evaluation. One key problem for determining the appropriate discount rate is that it typically depends more on subjective perception of the degree of risk or other experience factors than on a systematic approach. Thus, this study aims to identify, analyse, and document the type, role, and impact of risk factors influencing the determination of discount rates, and then to determine discount rate by using the aforementioned factors.

Jan 1, 2011

This Spotlight gives a brief summary of the proposed 1991 tax amendments of relevance to mines and mining houses. It should be read together with the author's article South African mining tax in the 1990's', which appeared in the August 1990 issue of this Journal. A number of tax amendments of relevance to the mining industry were proposed by the Minister of Finance in his March 1991 budget speech. In addition, certain other measures that may be implemented were set out in the budget review document released at the same time. A word of caution is necessary: these measures will become law only if and when they are enacted in the appropriate legislation. When this legislation is tabled in June, it may not contain all of the measures discussed below, some of the measures may appear in modified form, and other measures not discussed at the time of the budget may well appear. Unless otherwise stated, the 1991 tax amendments will affect companies with years of assessment ending in the twelve-month period to 31st March, 1992.

Jan 1, 1991

By L. Uotinen, M. Rinne, R. Mishra

Underground mining gives rise to geotechnical hazards. A formal geotechnical risk assessment can help to forecast and mitigate these hazards. Frequentist probability methods can be used when the hazard does not have many variables and a lot of data is available. However, often there is not enough data for probability distributions, such as in the case of new projects. The risk assessment is often subjective and qualitative, based on expert judgement. The purpose of this research is to present the use of Bayesian networks (BNs) as an alternative to existing risk assessment methods in underground mines by combining expert knowledge with data as it becomes available. Roof fall frequency forecasting using parameter learning is demonstrated with 1141 sets of roof fall data across 12 coal mines in the USA. The prediction is nearly identical for individual mines, but when multiple mines are evaluated it is difficult to find a single best fit distribution for annual roof fall frequency. The BN approach with TNormal distribution was twice as likely to fit the observed data compared to the Poisson distribution assumed in the past. A hybrid approach using BN combining multiple probability distribution curves from historical data to predict annual roof fall is proposed. The BN models can account for variability for multiple parameters without increasing the complexity of the calculation. BNs can work with varying amounts of data, which makes them a good tool for real-time risk assessment in mines.

Jun 1, 2021

By A. Brodt, I. Mezhibovsky

The traditional vertical transportation systems deliver both gangue and useful mineral. The extraction of the desired minerals requires the construction of mineral processing and waste management plants, driving production costs, and often creating a negative environmental impact. The proposed technology is an integration of mineral processing within the transportation system. The mined rock is crushed and then loaded into a vertical lifting system filled with heavy media, with an intermediate density between the mineral and the waste rock. Driven by gravity separation, the desired mineral floats to the earth's surface, while the waste sinks. Delivered minerals and sunk waste is extracted from the heavy media and is then regenerated to a dry state. The useful mineral should be suitable for further use, and the waste used for backfilling. Remained residues of the heavy media may be recycled and reused in the vertical transportation system. Trials of the proposed process in a pilot format have confirmed economic and environmental advantages over traditional methods of transportation and mineral processing technologies. Keywords: Gravitational processes of mineral processing, separation in heavy media, vertical transportation to earth's surface by floating up

Jan 1, 2020

By M. Ericsson

?Rare earths ?will not be bargaining instruments?? was stated in a headline in China Daily of 29 October 2010. The Chinese government is trying to fend off the persistent accusations from Japan, the USA, and Europe that it is manipulating the supply of these so called ?critical? metals to gain political and economic advantages. The critics maintain that China has taken the rest of the world hostage by controlling 97% of the resources of rare earths. These elements are crucial in a number of high-tech applications. They are not impossible to substitute, but difficult to do so effectively. The name ?rare earth? is a misnomer, as even the least abundant is 200 times more common in the Earth?s crust than gold. They are, however, difficult to find in economic concentrations. The Chinese near-monopoly over the rare earths, together with China?s scramble for other resources in Australia, Africa, and elsewhere around the world, is seen as an example of a Chinese strategy to take control of vital metal resources. The Chinese are also accused of using unfair and sometimes illegal business practices in this fight for resources. Practices which, critics claim, put the Chinese interests above the interests of the host countries, in particular in Africa.

Jan 1, 2011

By E. Kumar, L. A. Kumar

"A methodology is proposed to develop an optimization model to understand the impact of transporting minerals, from mines to the final destination, on air quality. Recently, there has been increasing concern about the combined effects of multiple activities over many years, and the regional environmental changes brought about by a single project. Environmental issues in the iron ore industry have highlighted the need to broaden the cumulative impact assessment. In this study, we simulated the optimal routes and quantity of materials needed to meet the destination plant demand based upon environment constraints (level of air pollution), as well as the cost of transportation and availability of materials. Multiple scenarios were developed to analyse the effects of changes in routes, alternative transport system (or multi-modal split), traffic congestion, and the cumulative impacts on air quality. The air quality impact zones of the study area were demarcated using a GIS technique. The expected outcome of the study is the selection of a suitable transport system for a particular site with the least impact on air quality, including the transportation route, relative to the minimum cost of transportation of the minerals from the mines to their final destination. The proposed methodology is evaluated with a case study. IntroductionIn India, the process of environmental impact assessment (EIA) has been focused primarily on the local impacts of projects, without considering regional environmental effects. Environmental clearances for proposed projects are based on reports of local impacts. However, any developmental project poses a potential risk to the environment as a whole, and not just in the immediate vicinity of the project. Recently, there has been increased concern about the combined effects of multiple activities over many years—the regional environmental changes due to development of a single project (Dutta, Mahatha, and De, 2004). Environmental issues throughout the country, particularly in the iron ore industry, have emphasized the need to broaden the analysis to include the combined impacts, or those forecast for a proposed region, on an existing environment. The most significant adverse environmental consequences of iron ore transportation are the deterioration of biodiversity and air quality (Kumar and Ajay, 2015)."

Jan 1, 2017

Where is Your Advertisement