Search Documents

By J. E. Murphy

Purification of samarium metal by sublimation and by vaporization from a low-melting metal flux, at the same temperature, were compared. Vaporization proved more effective for removing impurities such as magnesium, calcium, and manganese. Recovery of samarium, however, is more rapid by sublimation because of its constant rate of distillation.

Jan 1, 1970

By Oliver W. Keener

This paper describing the methods and costs of mining at the Hartley-Grantham mine of the Century Zinc Co. in the Tri-State Lead and Zinc district is one of a series being prepared by the United States Bureau of Mines can mining practices, methods, and costs in the various mining districts of the United States. LOCATION, HISTORY, AND GEOLOGY The Hartley-Grantham Mine is located just outside the city limits of Baxter Springs, Kans., as shown in Figure 1. A plan of the mine is given in Figure 2, and Figure is a cross section through A - A of Figure 2.

Jan 1, 1930

By E. D. Gardner

This paper is one of a series on mining methods and costs being published by the United States Bureau of Mines. In April 19.74 the St. Joseph Lead Co., at Atlanta, Elmore County, Idaho, was mining and milling about 225 tons of gold ore daily with a total force of 150 men. The mine, which comprises the old Boise-Rochester and Monarch properties, is at an elevation of about 6,000 feet. Snow lies on the ground about 5 months each year but does net interfere greatly with local operations. However, the road to Mountain Home, the shipping point 80 miles distant, passes over a high range and usually is closed by snow from about November 15 to June 15. Heavy supplies are brought in and concentrates trucked out during the summer. In winter the district is served by a biweekly mail plane and a passenger and express plane making 4 to 6 trips weekly. Mine timber is cut locally. A plentiful supply of water is obtained from a stream brought to the property through 7,500 feet of plume.

Jan 1, 1935

The principal activities of the Bureau of Mines Pittsburgh Mining and Safety Research Center during fiscal year 1971 (July 1, 1970, to June 30, 1971) are reviewed in part 1 of this paper. Part 2 summarizes publications during fiscal year 1971.

Jan 1, 1974

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

By E. G. Valdez

Laboratory research demonstrated that ceramic wall and floor tile can be produced from electric furnace phosphorus slags composed of calcium silicates. Grinding the slag in a pebble mill, followed by magnetic removal of deleterious magnetite, produced a raw material that could be compounded and formed into wall tile by dry pressing, sintering, and glazing. The effects of process variables such as forming pressure and sintering temperature were investigated. Wall tile bodies produced by this method were comparable to commercial tile. The tiles were readily glazed to a smooth shiny finish and met ASTM Specifications C34-62 for structural clay load-bearing tile. The estimated cost of producing wall tile by this method compared favorably with the retail market value for similar wall tile. Addition of borax or other additives to the ground slag followed by dry pressing and firing likewise produced a commercial grade of floor tile.

Jan 1, 1974

By N. S. Dalal, X. Shi

While it is known that vanadate and related compounds of pentavalent vanadium ( V (V)) exert potent toxic effects on a wide variety of biological systems, the underlying biochemical mechanism is still not fully understood ( 1- 3). One of the pathways is thought to involve the oxidation of NAD ( P) H. Thus, considerable effort has been devoted to finding the mechanism of NAD ( P) H oxidation by Vcvi (1-15). Erdmann et al. (5) first noted that vanadate stimulated the oxidation of NADH by plasma membranes and attributed this effect to a membrane containing NAD(P)H-dependent V(V) reductase. Later studies by Liochev and Fridovich indicated that endogenous superoxide ( 02 ) plays a central role in this reaction ( 4, 12, 13) . They proposed that NAD ( P) H dehydrogenases or oxidases produce 02, which causes VCV ) to stimulate NAD ( P) H oxidation via the following free radical chain mechanism ( 4, 12, 13) :

Mar 1, 1992

By E. P. Youngman

A new mining law for the Recublic of Polend was promulgated by presiden- tial decree dated November 29, 1930, published in the Journal of Lews (Dzienni stex) No. E, text 654, December E, 1530, and wes to become effective January 1, 1932, in all Polend except Silesie. Its adoption in Silesia wes dependent pon the action of the Silesian Diet. As the new law is considered an im- provement over the old Austrian Mining Lew, which is operative in the Silesian districts of Bielsk and Cieszyn, and the Prussian Kining Law, which is opera- tive in Upper Silesia, no delay in its adoption for Silesin was looked for. This new law codifies the various juridical regulations pertaining to ines existing in different parts of the Polish Republic but does not include legislation with respect to the extraction of minerel oil, especially crude oil. Petroleum legislation was postponed to a later date in order to facili- tate codification in other fields. Koreover, as the oil industry exists in Galicia elone, deley will not be detrimental.

May 1, 1932

By A. F. Colombo

Laboratory-scale tests were conducted by the Bureau of Mines on an argillaceous Michigan copper ore and mill tailing to determine the feasibility of leaching with acidified ferric sulfate solutions. The ore and tailings, containing 1.24 and 0.24 percent copper, respectively, were from the White Pine Copper Co., Ontonagon County, Mich. The investigation showed that ferric sulfate leaching of the ore and tailings followed a predictable pattern. Thus, with 4 hours of leaching, up to 58 percent of the copper in the ore was extracted, but prolonged leaching (2 to 3 weeks) was required to dissolve more than 90 percent of the copper. Similarly, about 50 percent of the copper in the mill tailings sample was dissolved in a few hours, but 8 days or more were required for extractions of over 90 percent.

Jan 1, 1962

By D. E. Fogelson

In a factorial experiment, blasting caps were detonated in three sizes of shotholes in mortar with three types of stemming--dry sand, wet sand, and hydrostone. Free-surface displacement pulses were recorded with a capacitive-displacement gage at a distance of 15 inches. The effects of decoupling and the type of stemming on the amplitude and the duration of the displacement pulse were determined. Both the amplitude and the duration of the displacement pulse were significantly decreased by increasing the decoupling, but they were little affected by the type of stemming.

Jan 1, 1965

By H. J. Heinen

This report summarizes preliminary research studies by the Bureau of Mines in electrowinning molybdenum directly from pure or impure molybdenum trioxide (MoO3) by fused-bath electrolysis in an open graphite cell without need of a protective inert atmosphere. A formulated electrolyte of the tertiary system containing 41.6 percent sodium pyrophosphate, 16.7 percent sodium tetraborat, 33.3 percent sodium chloride, and 8,4 percent molybdenum trioxide, by weight, electrolyzed at 1,000° C,, gave excellent results. Current density studies were made over a range from 20 to 260 amperes per square decimeter. Current efficiencies of 80 to 90 percent were obtained over the entire range. Yields up to 500 grams of molybdenum per kilowatt-hour were obtained. Higher current densities, however, reduced yields and produced a finer grained metal. The two most important facets in electrowinning molybdenum from MoO3, in an open cell, are temperature and electrode spacing to minimize or eliminate the formation of the suboxide MoO2, the major source of oxygen contamination. At temperatures of 1,000° C. and higher, together with the proper spacing of the electrodes, formation of oxides are practically eliminated. Molybdenum metal electrowon from pure MoO3 was 99.9 percent pure and contained 0,056 percent oxygen and 0,007 percent carbon. This metal, when arc-melted, had a Vickers hardness number of 175 and contained 50 parts per million oxygen and less than 10 parts per million carbon. Molybdenum metal electrowon directly from an impure MoO3 containing 90 percent MoO3 resulted in a metal of 99.8 percent purity.

Jan 1, 1961

By 1928-05-01

"The carnotite ores of Colorado and Utah were the chief source of radium for many years. In the fall of 1922; news of the very rich deposits of radium ore discovered in the Belgian Congo caused almost complete cessation of domestic production. The Congo ore contains pitchblend and a number of alteration products, including the new minerals bequerelite, curite, kasolite, stasite, and dewindite. Reports indicate that a considerable amount of ore containing over 50 per cent U308 has been produced. It seemed certain that radium could be extracted from the Congo ore at a much lower cost than from the relatively low-grade carnotite; and in order to preserve their elaborate marketing organizations, the larger American producers made agreements with the Belgium syndicate to market the foreign product in this country. The price of radium has been held at $70 per milligram. Extraction of radium from carnotite by the usual methods does not appear to be profitable at that price. With one exception, all American firms ceased production after their accumulated stocks of ore had been treated. The United States Radium Co., which continued to treat carnotite for several years, has recently shut down its plant.Although there is probably a large profit derivable from the treatment of Congo ore, it is not likely that the Belgium Syndicate will meet sufficient competition to cause any reduction in the present quotations. It is not known how long the high-grade ore will last, but when exhausted the price of radium may be expected to advance. According to K. L. Kithil3 it is the opinion of interested parties that, so far as can be forseen, radium will in future years never again be obtained at the present low price.Carnotite contains the valuable element, vanadium, which is not present in the Congo ore. The recovery of-vanadium is an important factor in the cost of extracting radium from carnotite, and under favorable conditions carnotite can be profitably treated for the vanadium alone. Vanadifecous sandstones are found ranging all the way from roscoelite (vanadium mica), containing little or no uranium; to a high-uranium and low-vanadium carnotite. Ores containing 2 per cent or more U308 are classed as radium ore and are sold on the basis of the uranium content, which is proportional to the radium content. Only in exceptional cases have ores been evaluated on the basis of both the radium and vanadium contents, although the presence of vanadium has undoubtedly influenced the price of radium ore."

May 1, 1928

By W. J. Fene

Ventilation is undoubtedly the greatest single safety factor in the operation of a coal mine. Any condition or occurrence that interrupts the ventilating current or changes its normal course through the mine workings is a distinct hazard and should be considered as such by every coal-mine owner, operator, and worker. The hazard, of course, is much greater in a mine that is emitting gas, as an explosive mixture can accumulate in a very short period if the ventilating current is interrupted. It is common to find one or more entries producing 600 cubic feet or more of methane per hour. If the ventilating current were short-circuited from these entries for 15 minutes, there would be an accumulation of 150 cubic feet of methane, which, when mixed with enough air to dilute it to the lowest explosive point, would make about 3,000 cubic feet of explosive mixture; this gas could be ignited in almost any normally operated mine by a cutting machine or other electrical equipment. The ignition of this quantity of an explosive gas-air mixture can readily cause an explosion of coal dust that would completely wreck the underground workings and possibly some of the surface structures. In fact, the ignition of one-tenth of the above quantity of an explosive mixture of gas and air might readily start an explosion that would, extend through every part of a large mine. The possibility of occurrence of interruptions to the ventilating current has received comparatively little consideration from mine owners, operators, and workers in many parts of the United States. Such a possibility should be considered in connection with every mine that gives off explosive gas, and steps should be taken to prevent it.

Jan 1, 1943

By D. J. Parker

Ability to signal the hoisting engineer in shaft mines is of utmost importance from the standpoint of safety and economy. The problem of signalling from the cages and especially from the moving cages has received too little attention from mine operators; however, this problem has been given considerable thought and attention by at least one large metal-mining company in Utah which has devised successful, economical, and safe systems of signalling from the cage whether it is moving or at rest. A Report of Investigations on "Methods used in Utah for signalling mine hoists from moving cages," by C. A. Allen, then a metal-mining engineer in the Bureau of Mines, was issued in June, 1920. As this report contains interesting history of systems of signalling from moving mine hoists, and describes several systems then in use, it is here quoted in full.

Jan 1, 1929

By Lars Osen

This investigation was undertaken to contribute to the understanding of underground pull tests by conducting laboratory tests under closely controlled conditions. Steel bolts, instrumented with electrical resistance strain gages, were anchored in an aluminum block, a granite block, and a steel sleeve, and were subjected to pull tests. The bearing plates used were either flat7 dished, or embossed. In pull testing a bolt that is prestressed, there is a range of loading during which bolt load is greater than the jack-applied load, This study showed that preload, the size, shape, and type of bearing plate; and the geometry of the system determine the point at which bolt load and applied load become equal. The effects on bolt load of both a theoretical solution and actual pull tests were analogous and led to similar results.

Jan 1, 1965

By Curtis D. Edgerton

The Pittsburgh Mine Map Repository of the Bureau of Mines serves as a basic reference file for the archival preservation of mine map data of mines east of the Mississippi River. About 22,000 of an estimated 500,000 available mine maps have been microfilmed A computerized index serves as the mechanism for retrieval of any microfilmed mine map. The operation, equipment, and index are described in the report.

Jan 1, 1974

By J. M. Mutmansky

"The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous miner- generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory- generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM ). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared. IntroductionIn many biomedical studies, researchers routinely introduce a dust mass into an experimental environment to assess the response of a biological entity, usually lung macrophages in vitro or a live laboratory animal, to the dust mass. To provide data of maximum usefulness, it is highly desirable to use dust with characteristics of actual mine airborne dust. The primary objective of this research was to produce dusts in the laboratory similar in chemical, mineralogical, and physical characteristics to mine airborne dusts. This paper outlines the evaluation of the physical characteristics of the lab-generated dusts.Particle shape analysis is perhaps the least-developed area in mineral-related particle science and technology. There are still no standard methods or instruments to scientifically quantify particle shapes. To date, many attempts have been made to characterize particle shapes. These procedures can be roughly classified into three categories:"

Dec 1, 1995

By R. W. Watson

This Bureau of Mines report summarizes some recent results on the sensitivity of various experimental explosive systems using ammonium nitrate (AN) as the oxidizing agent. The sensitivity survey included drop-weight and friction testing and sensitivity to initiation by projectile impact and a No.8 blasting cap. It was found that certain types of AN prills can result in cap-sensitive mixtures when combined with No.2 diesel fuel (Fa); prilled AN mixed with nitromethane also result in cap-sensitive mixtures. Mixtures of AN prills and neat 1-and 2-nitropropane were not cap-sensitive, and the use of powdered or grained aluminum in AN-FO did not adversely affect the sensitivity except possibly to increase its sensitivity to friction.

Jan 1, 1974

By C. J. Johnson, C. J. Bise

"As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity.Room-and-pillar mining accounts for approximately 68% of the nations underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-mid-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.IntroductionThe ultimate goal for any coal mining company is to effectively use its human and financial resources to maximize its profits through the extraction of its reserves. Although recent workforce reductions in the industry have resulted in a more efficient use of labor and increased productivity, there comes a point in time when further reductions in the numbers of workers in each operating section are impossible with existing equipment. For example, Farinelli and Bise (1987) found that labor cost constituted 62% - 73% of the cost per ton of coal at the mining section, with a minimum crew size. Thereafter, efforts to increase productivity must focus on more efficient mine plans and technology.The fact that an increase in productivity can be realized by reducing non-productive time (change-out and tram time) and converting it to productive time has been known and demonstrated for quite some time. What has not been demonstrated frequently is the quantification of the potential productivity increase of currently emerging technology or ""add-on"" equipment. It is one thing to be able to say that a piece of equipment will make an operation more productive, but it is another thing to be able to quantify the productivity increase that will justify the purchase of the new equipment. Not only is a financial benefit possible in room-and-pillar mining with an increase in productivity, but a decrease in the time necessary to develop a longwall panel can also occur.The purpose of this paper is an analyze the impacts of a changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to several scenarios incorporating emerging technology. To do this, four cases will be developed. A base case, consisting of the typical manner in which continuous-miner sections are currently operating, is compared to three layouts incorporating: (1) flooded-bed scrubbers on radio remote-controlled continuous miners, (2)a continuous miner with side-mounted roofbolters, and (3) a continuous miner with side-mounted roofbolters used in conjunction with a continuous-haulage system."

Jan 1, 1989

By S. P. Kinney, P. H. Royster, T. L. Joseph

An investigation of the production of iron in the blast furnace is obviously not an easy subject for research . Enough is known of the mechanical , thermal and chemical conditions existing inside the furnace to say certainly that they are complicated. Furnace operators have found that the process is sensitive to a number of known and to many unknown operating conditions . In order to form any conclusions of value , it seems necessary to collect a large amount of data taken with considerable care and accuracy. These facts make a blast furnace research difficult but not impossible . The most serious obstacle in attacking the problem comes from the fact that it is useless in the design and operation of the blast furnace to use the method of " trial and error , which has proved valuable in so many other industrial problems . The variables are so interrelated and are so dependent one on the other that the number of experimental combinations to be tried is enormous . There are certainly not less than twenty factors in furnace operation and design that are known to influence the results . This is apparent if it is remembered that a phrase like " size and shape of the furnace" includes height of the furnace , height , diameter and angle of the bosh , inwall batter , stockline diameter , and furnace volume ; and that a phrase like " chemical and physical properties of the fuels charged " includes size and shape of the lumps , density, porosity and strength of the coke , in addition to its chemical analysis . Let us suppose that we need choose for each of twenty factors one of two values , for example , suppose we must say only that the furnace shall be " tall " or " short , " that the bosh angle shall be " flat " OF "steep , that the ore shall be " coarse " or " fine , " or that the blast has to be "hot" or " cold , " the number of resulting combinations is more than one million . In putting twenty pennies on the table , either heads up or tails up, the number of permutations possible is the twentieth power of two , slightly more than one million. It is obvious , therefore , that some sort of mathematical relationship , a set of rules of thumb , laws , curves or the like , are needed . Whether the relationships , curves or formulas are derived from experiment , from theory, or from mere guess -work, makes no difference provided they agree with the known facts . If they do not agree with known facts , they are worthless no matter what their origin or how weighty the " authority" vouching for them. Few such relationships have appeared in blast- furnace literature , and it may be doubted whether such formulas can be discovered .

Sep 1, 1923