Search Documents

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By Joseph J. Wallace

1. The Pocahontas No. 3 and Pocahontas No. 6 ere the two most important beds in Mercer County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 188 million short tons as of January l, 1953. Of this total, 80 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

This chapter describes the adverse health effects associated with exposure to respirable coal mine dust. Epidemiological studies of underground and surface coal miners in the United States and other countries are discussed. Also discussed are animal studies that add to our understanding of particle deposition and retention in the lungs and associated disease responses. This chapter emphasizes studies that (1) were performed since the passage of the Federal Coal Mine Health and Safety Act of 1969 [P.L. 91- 173], (2) used standardized methods of exposure monitoring and disease classification, and (3) investigated exposure-response relationships between respirable coal mine dust exposure and disease. Several published review articles contain further discussion of health effects studies of coal miners [Attfield and Wagner 1992b; Petsonk and Attfield 1994; Cotes and Steel 1987; Merchant et al. 1986; Morgan and Lapp 1976; Morgan 1975].

Jan 1, 1997

By L. C. IlsLey

A n'Ulllber or operators have installed f'lBJ!le-proot or so-called exploaion­ proot electrical outfits, under the impression that such equipments met· all of the reqiirements of the Bureau of Mines as regards safety, There a.re todq in gaseous mines a large nwnber of euipments that have not been approved by the Bureau ot Mines, and unless mod1f'iecl could not receive sucl1 approval.. These e qu.ipments represent in pa.rt the product of manufacturers whil ha.ve never submitted. equipments for insri?ction or tests. and iri pat types developed. previous to the safety work or the bureau. Sometiu.es saleimen advocate the use of unapproved. types in gaseous mines in place of Bureau of Mines approved outfits, the purchase price beini slightly less than approved types,

Sep 1, 1922

By Lloyd A. Morley, Alan M. Christman

General An important part of any mine power distribution system is its con¬nection to earth or ground. The grounding network serves to protect men and machinery from the hazards associated with electrical equipment which is operating improperly. Since the mine site is determined by the location of the rock or mineral to be extracted, the conditions required for the installation of an adequate grounding system are not always easily met. If annual rainfall is low or soil resistivity is high, an extensive array of buried metallic conductors may be necessary to assure a low-resistance connec¬tion to earth. Measurement of soil parameters can be made before the construction of a grounding grid is begun, and the configuration of a metallic network, which will yield the desired values of earth resistance and potential gradient, thereby ascertained. Proper design at the time the ground bed is installed will save much time and expense in later years. Ground conductors extend from the buried grid to each piece of mo¬bile and portable equipment via overhead lines or multi-conductor cables. In this fashion all machine frames are referenced to the same potential as the grounding medium. Protective circuitry must be installed to monitor\current flow in the ground conductors or the potential drop across the neutral grounding resistor, which is placed between the grounding grid and the neutral point on the distribution transformer secondary. When properly co-ordinated and used in conjunction with a low-resistance

Jan 1, 1976

By D. A. Hill

Introduction The fields of an infinite line source in the presence of a conducting half-space have been examined by Wait and Spies (1971). In any real communication link using a current-carrying cable for the transmitting antenna, the cable is of finite length. Here we examine the fields of a finite length cable carrying a constant current in the presence of a homogeneous conducting half-space. The constant current assumption is valid at sufficiently low frequencies when an insulated cable is grounded at the end points (Wait, 1952; Sunde, 1968). Here we examine both surface and buried cables since both downlink and uplink communication links are of interest. Also, we examine both frequency and time solutions since either CW or pulsed communications may be used. Finally, it is necessary to include both magnetic and electric field solutions since reception could be with either loops or dipoles. Since the finite cable solution is more complicated than both the infinite line source and the short dipole solutions, we explore under what conditions a cable appears to be either infinitely long or very short. Some special cases, such as- the low frequency limit, permit analytical solutions which exhibit the dependence on various parameters, such as cable length, quite clearly. Frequency Domain Subsurface Fields The geometry of a line source of length 2[l] located on a conducting half-space with the observer in the half-space is shown in Figure 1. The fields

Jan 1, 1973

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least- radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By R. P. Vinson, D. P. Tuchman

The personal dust monitor (PDM) is a sampling device developed for measuring the personal exposure to coal mine dust of mine workers. The device is based on proprietary technology known as the tapered element oscillating microbalance (TEOM) originally developed as a fixed- site environmental particulate mass monitor by Rupprecht and Patashnick Co., Inc., Albany, NY. Currently, the monitoring of exposure to coal mine dust relies on periodic samples taken by traditional coal mine dust sampling units that use a cyclone, filter, pump, and laboratory measurement of the filter mass. Better measurement of mine dust levels has been the goal of industry and labor for nearly two decades. PDM technology offers accurate, end-of-shift and near real time assessment of worker dust exposure. Laboratory and underground tests compared measurements taken by a prototype PDM-2 (a two-piece TEOM) to the average of multiple personal dust samplers monitoring the same space. In the range of mass loadings P between 0.5 and 4.0 mg/m the PDM met a 25% accuracy criterion 95% of the time with 95% confidence. However, some questions still exist about potential bias between types of coal. The prototype two-piece device is in the process of being combined into a single unit that also contains the miners' cap lamp creating a more ergonomic dust sampling system.

Active and abandoned mine sites can be an irresistible- - and sometimes deadly - - draw for outdoor enthusiasts, particularly children and young adults. Despite repeated warnings, posted signs, and fencing, tragedies involving accidents on active and abandoned mine property continue to make headlines, especially with the arrival of warmer weather and the summer months ahead. Over the last few years, there have been dozens of tragic incidents involving children and adults ventur­ing onto active and abandoned mine property. They include: A 16-year-old youth suffered fatal injuries after his all-terrain vehicle became airborne in an accident at a gravel mine near Albany, New York. A young boy was electrocuted when he contacted a high-voltage power line while sliding down a stockpile at a sand and gravel mine in Grand Island, Nebraska during its off-shift hours.

Jan 1, 1999

Continuously monitor air-borne radon daughters that are a hazard to underground miners. Approach A beta detector continuously counts beta activity collected on a filter paper to allow calculation of exposure in working level units. How It Works At each Site a constant flow pump draws mine air through a fiberglass filter located in front of a beta detector (pancake type Geiger Mueller tube), Radioactive particles (products of the radon 222 gas emanating from the mine walls) collect on the filter and decay, releasing alpha and beta particles as well as gamma rays. A portion of the beta particles penetrate the Geiger tube window and create electrical pulses in the tube. These pulses are then amplified and sent by a coaxial type or shielded electrical cable to a central monitor located some distance from a working level detector. At the central monitor incoming Signals are amplified and fed into two channels, (See the block

Jan 1, 1979

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

By J. F. Barkley

As part of the work of serving as Chairman of Subcommittee 3, Health and Industrial Requirements, of the American Society of Mechanical Engineers' Committee on Air-Pollution Controls, the author assembled the following information on accepted maximum permissible concentrations of air pollutants from the standpoints of health, damage to vegetation, damage to property, and requirements of industrial processes. A search in technical literature was made followed by direct inquiry to all State governments as to their regulations. The subcommittee membership - G. D. Clayton, senior sanitary engineer, Public Health Service, United States Department of Health, Education, and Welfare, Detroit, Mich., Dr. L. Greenburg, commissioner; Department of Air Pollution Control, New York, N.Y., Dr. M. Katz, Defence Research Chemical Laboratories, Ottawa, Ontario, Canada, and Dr. H. H. Schrenk, research director, Industrial Hygiene Foundation of America, Inc., Mellon Institute, Pittsburgh, Pa. - reviewed the information and made very helpful comments and corrections.

Jan 1, 1954

By W. H. Eddy

Laboratory batch and small-scale continuous flotation tests were con-ducted by the Bureau of Mines on a mica waste tailing from Kings Mountain, N.C., to determine the feasibility of producing high-quality mica, feldspar, and glass sand. Mica was recovered by two methods; one was by flotation in an alkaline circuit, which produced a mica concentrate assaying 92.0 percent mica with a recovery of 87.l percent, and the other by flotation in an acid circuit, which produced a mica concentrate assaying 91.0 percent mica with a recovery of 79.4 percent. Continuous flotation processing yielded a feldspar concentrate assaying 1.10 percent Na20 and 13.50 percent K20, with recoveries of 66.4 and 80.6 percent, respectively. The feldspar tailing was high-quality quartz glass sand analyzing 98.6 percent Si02 and 0.02 percent Fe203.

Jan 1, 1969

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By F. R. McDonald

The compound ?-valerolactone has been identified in an acid fraction isolated from waste water collected from an in situ oil-shale retort. Infrared, nuclear magnetic resonance, and mass spectrometry were used by the Bureau of Mines to confirm the identification of a subfraction collected from a gas chromatograph.

Jan 1, 1974

By Tony Keller, Setsuo Maeda

Hand-Arm Vibration Syndrome (HAVS) was identified as early as 1918 in Bedford, Indiana in the U.S. Since then much research work has been done around the world in the areas of medical, epidemiological, engineering and legal aspects of HAVS. In Japan, much of the pioneering work in this field has been performed by Dr. Setsuo Maeda and his staff at the National Institute of Industrial Health (NIIH) in Kawasaki. Most recently, reports of work done by this group and by Dr. Ren Dong1 of NIOSH in the U.S., as well as many other suppliers and Japanese practitioners were presented at the 13th Japan Group Meeting on Human Response to Vibration held in Osaka2 during August 3-5, 2005. [ ]

Jan 6, 2006

By James P. Ulery, Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for pre- venting explosions during auger mining.

Jan 1, 1993

By S. A. Gustavson, H. E. Olund

This report has been prepared to review the history of the Premium Price Plan for copper, lead, and zinc, which was in operation from February 1, 1942, to June 30, 1947. It includes various charts and tables comparing costs and production data, and data on exploration premiums that were included in the Plan during the last year of its operation.

Jan 1, 1950

By J. C. Nigro

Hematite-to-magnetite reduction kinetics were investigated mainly in CO-CO2 atmospheres at temperatures ranging from 500° to 1,000° C. Reduction rates were measured with a thermobalance, which recorded the weight loss as the specimen was reduced. Reduction data on both synthetic and natural hematite spheres showed good linearity of ro [1-(1-R)1/3] with time, t, up to over 85 pct conversion to magnetite; the rate coefficient (k[L], cm/min) obtained from the linear portion of the plot was used to characterize the penetration rate of the hematite-magnetite interface. Gas composition, porosity, and silica content were major factors affecting the rate. Temperature dependency of the reaction rate was small, yielding a mean activation energy of about 3 kcal/mole. Silica additions increased the reaction rate, probably through an increase in the effective surface area and diffusion; however, above 900° C, silica can react to form fayalite. Experimental data showed that the linear thickening rate of the magnetite layer, normally evidence of a chemically controlled reaction, can also be indicative of a reaction controlled by both mass transfer and diffusion. Evidence from this study indicates that the dominant rate-controlling factor in the reduction of hematite to magnetite at high temperatures is transport in the gas phase.

Jan 1, 1973