Search Documents

By M. D. Aldridge

The results of a four-year research effort aimed at developing a practical and effective electronic system for monitoring safety conditions throughout a coal mine by displaying, at a central location, remotely measured parameters are described. This document reports on the design details of the sensor packages and the data processing program used in an experimental monitoring system. The results of special ventilation monitoring experiments and several sub-system considerations are also described.

Jan 1, 1974

Approximately half of all the fuel energy used in the United states is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation's reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950

By Shelby Z. Palya

"INTRODUCTION The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mining substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1975, to December 31, 1979. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 3 the 5-year lists of publicatioll3 and articles, from January 1, 1960, to December 31, 1964,4 from January 1, 1965, to December 31, 1969,5 and from January 1, 1970, to December 31, 1974; 6 and the annual lists of Bureau publications and articles from January 1 to December 31, 1975,7 from January 1 to December 31, 1976,8 from January 1 to December 31, 1977,9 and from January 1 to December 31, 1978.10"

Jan 1, 1980

By A. T. Iannacchione

The Bureau of Mines established geologic factors affecting the mining of the Lower Kittanning coalbed to aid in coalbed minability studies and examined the occurrence of "wants" (places where coal is missing) and types of unstable roof rock strata. Trends established from mapping, including prediction of areas of high methane emissions, were extrapolated to unmined areas. 'Wants' in the coalbed are of two types: Erosional and depositional. Erosional features occur where north-south-trending sand-filled channels cut into the coalbed. Variations in depositional environments have caused the coalbed to "split" into several thinner units. Slickensides, commonly indicative of unstable roof, are adjacent to and on the underside of sandstone channels; they were caused by differential compaction and by soft sediment sliding along the contact between the sandstone and adjacent shale. The frequency of unstable roof also increases where the interval between the Middle and Lower Kittanning coalbed is less than 30 feet. The zones of weakness at the contacts above and below the Middle Kittanning coalbed are the controlling factors for unstable roof in these strata. Methane emissions from the coalbed are controlled primarily by depth, fracture permeability, and rank of coal. Local geologic factors are coalbed thickness, associated rock strata, structure, and proximity to outcrop.

Jan 1, 1979

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite. During the early years of these plants little success was anticipated from the use of bituminous coals and lignites, but in 1904 and 1905 it was fully demonstrated at the Government testing station at St. Louis that these fuels could be utilized to excellent advantage. However, although many producer-gas plants in daily operation are using bituminous coal and lignite, many power-plant men are still skeptical regarding the successful commercial use of these fuels.

Jan 1, 1916

By John D. Spencer

Projects aimed at achieving the least disturbance to the Nation's air, water, and land resources in the mining and utilization of coal continued to be a feature of the Bureau of Mines coal program. This reflects the current concern about damage inflicted on the environment by our growing and increasingly affluent society. Mine Health and Safety research, along with investigations related to all other aspects of coal extraction and use, also continued to be implemented and expanded.

Jan 1, 1970

By J. B. Zadra

Tungsten, a comparatively new metal, is one of the important strategic war materials. In peacetime, tungsten is widely used as a filament in elec¬tric lamps and electronic tubes and is a vital constituent of some of the most important industrial alloys. High-speed tool steel containing tungsten and stellite alloys containing cobalt, chromium, and tungsten are extremely hard and resistant to corrosion. These alloys and the tungsten carbides are unequaled as cutting tools and in other wear-resistant applications. They play a prominent role in the present era of mass production. Alloys containing tungsten resist oxidation at high temperatures and have been key alloys in the development of modern aircraft. The adaptability of tungsten to new uses is expanding, particularly in the high-temperature range. Domestic production of tungsten has come from a large number of deposits in 17 of the 49 States; but, of the total domestic output from 1900 to 1956, more than 80 percent was produced from mines in North Carolina, California, Colorado, and Nevada. The average tenor of the mined ore was less than 1 percent tungsten trioxide (W03).

Jan 1, 1959

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite.

Jan 1, 1916

By W. A. Cole

This report covers the preliminary phase of an investigation of some clays and shales and other materials in North and South Dakota to determine the feasibility of lightweight -aggregate manufacture in the two States. The background of the light - weight -aggregate industry, on a national basis, and results of preliminary laboratory testing of samples of North and South Dakota clays and shales from various localities are presented herein. The countrywide search for lightweight aggregates was necessitated toward the end of the 19th century by the change in building design from thick, heavy, load- bearing walls to a framework of structural steel .beams and columns with thin walls, followed shortly by the use of reinforced concrete and structural concrete as materials for the load-supporting frame. Ordinary concrete, with sand and gravel aggregate, weighs about 150 pounds to the cubic foot. A lighter concrete was needed to relieve the dead load and make it possible to construct higher buildings or add stories to existing buildings.

Jan 1, 1954

By William H. Schiffbauer

This report details a microcomputer-based control and monitoring network that was developed in-house by the U.S. Bureau of Mines and installed on a continuous mining machine. The network consists of microcomputers that are connected together via a single twisted-pair cable. Each microcomputer was developed to provide a particular function in the control process. Machine-mounted microcomputers, in conjunction with the appropriate sensors, provide closed-loop control of the machine, navigation, and environmental monitoring. Off-the-machine microcomputers provide remote control of the machine, sensor status, and a connection to the network so that external computers can access network data and control the continuous mining machine. Because of the network's generic structure, it can be installed on most mining machines.

Jan 1, 1993

By James J. Dowd

During and immediately following World War II, the heavy demands for steel required the mining of unusually large quantities of coal for the manufacture of metallurgical coke. The largest demand for metallurgical coke is in the Appalachian region, which comprises central and western Pennsylvania, Maryland, West Virginia, Virginia, eastern Kentucky, Tennessee, and Alabama. This demand is satisfied by coke made from coals within the region; consequently, the reserves of coking coal in this region are being depleted more rapidly than reserves in other coal-producing regions. The supply A' high-quality coking coal during the war was inadequate, and some coke were forced to use inferior coals. The coke produced from these inferior coals adversely affected the rate of production. Another national emergency probably would produce a similar condition, and in the interest of -national security, the Munitions Board of the National Military Establishment requested the Bureau of Mines to evaluate the reserves of coals suitable for the manufacture of metallurgical coke. All bituminous coals in the Appalachian region are coking, and as the coal that produces the better metallurgical coke become depleted, other coal previously considered inferior will be used. The general trend is toward the use of lower-quality coals for metallurgical purposes.

Jan 1, 1950

By C. A. Kumke

The Korean crisis and the cessation of Russian manganese-ore shipments to the United States in 1950 reemphasized the almost total dependence of the domestic steel industry on foreign supplies for metallurgical-grade manganese ore. In this emergency, Congress authorized the Bureau of Mines to undertake experimental mine and process development work on the known large reserves of low-grade manganese ore in the Artillery Mountains region in Mohave County, Ariz. The objective of the work was to obtain the basic mining and metallurgical data needed to make specific plans for initiating exploitation of the deposits within 3 years if high-grade foreign ore could not be obtained during the emergency. The manganese deposits of the Artillery Mountains region are in an area of about 25 square miles on the north side of the Bill Williams River in southern Mohave County. Lasky, of the Federal Geological Survey, has estimated reserves at 175 million tons of manganiferous material assaying 3.5 to 4 percent Mn. Although the man¬ganese occurs in various Tertiary and Quaternary formations as both bedded and fissure vein deposits, the more important syngenetic deposits are found in upper and lower manganiferous zones in the sedimentary beds of playa and alluvial fan origin that constitute the Chapin Wash formation.

Jan 1, 1957

By R. S. Dean

"It has long been recognized that the properties of polycrystalline substances are not the same as those of single crystals. These differences are especially marked in metels and metallic minerals, and are of greatest practical importance in metal working and ore treatment. The property changes encountered in passing from a metal single crystal to a poly-crystalline aggregate are the same as are produced by cold-working a metal or by the precipitation of a disperse phase. Hence, we may logically assume that the property changes are all due directly or indirectly to the formation of interfacial area or internal surface. Our problem, then, is to ascertain the physicochemical state of the metal atoms at such internal surface and show how this physicochemical condition accounts for the pronounced changes of mechanical, magnetic, and electrical properties that accompany increased internal surface.GENERAL CONCEPT OF INTERNAL SURFACEIn 1678, Huyghens attempted to explain the double refraction of calcite by postulating that crystals were built from a regular arrangement of ellipsoidal particles. Over 100 years later, Abbé Hauy concluded from his studies of cleavage that crystals might be built from small units, but the units were of the same shape as the entire crystal. This idea, which was prevalent in mineralogical thought before the advent of X-ray spectrometry, was discarded when the great success of Bragg made it appear that the chemical atoms were in reality the elements of structure. In the further development of X-ray technique, however, C. G. Darwin, in England, and P. P. Ewald, in Germany, found it necessary to postulate crystal units con¬taining many atoms. The latter gave the name of mosaic crystals to those so constituted. The individual units are supposed to Possess the ideal atomic arrangements revealed by the X-ray but are not oriented with respect to one another."

May 1, 1938

By L. D. Tracy

This paper represents work conducted by the Bureau of Mines in cooperation with the Illinois Geological Survey and the Engineering Experiment Station of the University of Illinois.

Jan 1, 1926

By D. Harrington

"FOREWORDVirtually all government agencies undertook many additional responsibilities during the period immediately preceding World War II; these responsibilities increased vastly in importance and scope after the actual declaration of war following the attack on Pearl Harbor. The Bureau of Mines was one of the agencies thus affected, and it was called upon to perform many duties foreign to its normal peacetime activities.The Health and Safety Division of the Bureau of Mines, at that time designated the Health and Safety Branch, was given several important and difficult duties and responsibilities of an unusual nature because of the war while of necessity-continuing its normal functions of assisting the mineral industries in the preservation of life and health and the protection of property, this being of especial importance in wartime because of the pre-eminent importance of having maximum output of essentially all types of mineral products. Some of these additional functions were given to the Health and Safety Division because the organization of the Division, with its field set-up dividing the Nation into districts with competent, experienced personnel in charge of its work, provided the nucleus of personnel and procedure through which rapid and smooth expanded functioning was feasible.In addition to the responsibilities directly attributable to definite war activities, such as the administration of the wartime Federal. Explosives Act and the Mineral Production Security Branch a new branch (then designated division) was formed to investigate coal-mine health and safety problems after the enactment of the Federal Coal-Mine Inspections and Investigations Act, which became a law on May 7, 1941, but which actually began to function actively after the declaration of war in December 1941.The purpose of this publication is to provide a brief historical record of the activities of the Health and Safety Division as a whole and of its individual branches during the war. The detailed record has been filed in the Archives Building, Washington, D. C."

Jan 1, 1949

By Paul T. Alexander

After evaluating preceding studies and designs of lightweight supports, ESD selected the all-hydraulic and the hydromechanical concepts for detailed design and fabrication. Further analysis and testing showed that the all-hydraulic design was economically justified and met all the crucial engineering, manufacturing, and design criteria identified during the evaluation phase. Following Bureau of Mines approval of the detailed design, four all-hydraulic support models were fabricated. Once functional and structural testing was successfully completed, 40 additional units were constructed and distributed for in-mine testing. The units were very well-liked by all three demonstration mines. The wide- spread interest in supports for seam heights greater than 8 feet led to expansion of the design data package. ESD designed four basic models to cover the new height range, but no hardware has yet been fabricated for the new design.

Jan 1, 1982

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system or systems, thus disclosed. Of the several systems initially investigated and evaluated, four Showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By Frank C. Townsend

Waste disposal schemes using spent shale in embankments require a thorough knowledge of its geotechnical engineering properties for environ-mentally safe disposal. In this context, the objective of this laboratory investigation was to determine the physical properties, geotechnical properties, and composition of spent oil shale retorted by the PARAHO and TOSCO processes. Physical properties consisted of mechanical analyses, Atterberg limits, and specific gravity determinations. Geotechnical engineering properties were determined by compaction, maximum-minimum density, unconfined compression, triaxial compression, permeability, direct shear, Ko, cyclic tri-axial, resonant column, and Los Angeles Abrasion tests. Petrographic, chemical, and scanning electron microscopy analyses were used to determine compositional features. Unprocessed shale is hard and durable and more properly described as a carbonate rock instead of shale. PARAHO is classified as a GP, while TOSCO classifies as an SM. PARAHO requires no moisture for compaction to maximum densities; however, TOSCO does. Retorting causes a loss in durability but creates self-cementing characteristics, which for PARAHO a 3-to 8-fold strength increase was observed, while for TOSCO the increase was 1.5 to 3 folds. The shear strength, compressibility, and dynamic properties of compacted PARAHO are comparable to those for sandy gravels. Compacted PARAHO is semipervious, while compacted TOSCO can be semipervious to impermeable.

Jan 1, 1979

By W. D. Mcmillan

Important reserves of nickel ore occur in the Levies district in Oriente, Cuba. The area is mountainous and mostly covered by heavy vegetation. The ore bodies comprise surface tracts of nickeliferous laterite underlain with decomposed serpentine of ore grade. The Cuban Nickel Co., a wholly owned United States Government corporation, owns a plant for leaching the nickel from its ores at Nicaro, Oriente, Cuba, Between December 1943 and March 31, 1954, 5,902,225 short tons of ore was treated, with a recovery of 116,206,519 pounds of nickel (52,711 metric tons). In 1953, 1,330, 224 short tons of ore was mined and 27;"3,129 pounds of nickel produced. The Cuban Nickel Co. also owns a townsite, with the necessary facilities, mining equipment, and 11 miles of railroad. Ore for the plant has been produced from the Ocujal-San Juan claims on lends owned by the Nicaro Nickel Co., a sub¬sidiary of Freeport Sulphur Co. The Government enterprise is man-aged by the Nickel Processing Corp. The Cuban Nickel Co. has denounced mineral concessions and has purchased other claims from private owners.

Jan 1, 1955