Search Documents

By P. C. Van Natter

Numerous mine fires have resulted in high death tolls and considerable finan¬cial loss during the history of coal mining. In most instances the death toll and financial loss were greater because of inadequate fire-fighting facilities. The information in this report is presented in the hope it may serves as a guide in the selection, placement, and care of fire-protection systems in similar coal mines. The adequacy of fire protection varies according to size of operation, employment, and production. When fires occur on the surface or underground, measures must be applied quickly to prevent incipient fires from spreading. The record of coal-mine fires shows that, in many instances, facilities for combating fires were very meager or were absent. It would be virtually impossible to establish and maintain all the necessary facili¬ties that may be needed to extinguish widespread mine fires, but it is believed that the coal industry can ill afford less than the minimum required by other industries where the time element and avenues of escape are much more favorable.

Jan 1, 1958

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

To improve the level of hearing protection by providing workers with an inexpensive, easy-to-use device to check earplug fit. Background Approximately 30 million workers are exposed to hazardous noise on the job, placing them at risk of permanent hearing loss, tinnitus, and other disorders. Although the preferred solution is to eliminate noise through engineering controls or to reduce noise exposure through administrative controls, hearing protectors are critical when noise is unavoidable. Studies of hearing protector users have shown that average protection values in the real world are much lower than the labeled noise reduction ratings determined in laboratories with trained and motivated subjects. Even worse, many hearing pro­tector users get virtually no protection at all because of poor fit. The studies also show that users have a harder time achieving adequate protection levels with earplugs than with earmuffs. It?s difficult for users to tell if earplugs are working well just by looking at them. A more accurate approach is to check how much they block or ?attenuate? noise. Earplugs vary in their attenuation characteristics, with most providing a maximum of 20?35 decibels of noise reduction when worn correctly. Any earplug that?s suitable for use in noisy settings will attenuate noise by at least 15 decibels. Personal fit testing is an effective way to help hearing protector users improve the fit and protection levels of the devices. However, existing fit-testing systems are expensive and unsuitable for use at many industrial worksites.

Dec 1, 2008

By F. R. Cattoir, D. H. Baker

Fused - salt electrorefining has been successfully applied to the purification of vanadium metal . The electrolyte used in this refining technique was sodium chloride to which had been added 3 to 6 percent vanadium as vanadium dichloride . The average deposition current efficiency was 91 percent . Oxygen and nitrogen , the impurities in commercially produced vanadium metal , were reduced by two - thirds of the amount contained in the feed material . Hardness of the vanadium- metal product was reduced from an initial 97 Rockwell B ( RB ) to a minimum of 35 Rg . The reduction of these impurities markedly improved the plasticity of the final product obtained by melting the crystalline cell metal into small ingots . These ingots could be given a 99 - percent cold reduction by rolling before edge cracking appeared . Growing interest in high - purity vanadium and the industrial need for purer metals and improved alloys for use under high temperatures and high speeds have demanded the elimination and/or control of impurities . Accordingly, research to eliminate or control the undesirable impurities has been expanded .

Jul 1, 1960

By J. D. Dixon

The Bureau of Mines investigated the principles of support-rock interaction, based on structural matrix methods which permit mathematical formulation of the problem and computer solution. The principles are given under two main sections: the first discusses the idealization of the tunnel support structural system for matrix analysis; the latter discusses the analysis procedures necessary for carrying out the solution. A general frame matrix computer program and a medium-size computer should be sufficient for carrying out the procedures involved. The example problem consists of a circular tunnel support which is subjected to a uniformly distributed vertical load, Three wall thickness-radius ratios are studied in combination with four support-rock modulus ratios. This problem illustrates the main procedures of the support-rock interaction analysis involved, and examination of the results reveals the influence of the relative rigidities of the support and the rock.

Jan 1, 1971

By d&apos, Kathleen J. Amico

THIS summary appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S mineral production also is included.

Jan 1, 1964

By J. H. Stears

Increasing use of Birmingham and other roof trusses prompted a Bureau of Mines study of support forces produced on a mine roof by these members. Equations, obtained from laboratory and field tests, are given for calculating the contact forces between the roof strata and a typical truss. Actual contact forces for a specific truss are difficult to estimate because of variable friction loss at the contact points. A finite-element analysis, using typical contact forces, indicated that trusses have a negligible effect on the stress field in massive, competent roof strata. The effectiveness of trusses in supporting broken rock strata was not analyzed. However, experience has shown that trusses are effective in supporting incompetent roof.

Jan 1, 1988

China?s New Steel Complex Postponed. - The planned $5 billion Baoshan Steel Works near Shanghai is being laid aside for 6 months to a year, and may be abandoned altogether. The second phase of construction, in which Wean United, Inc., of Pittsburgh was a major participant, has definitely been cancelled. Over $1 billion had been committed to the 6 million-ton-per-year plant. U.S. Firm Develops South African Fluorspar. - The Armco Bronne Co. of Middletown, Ohio, plans to spend $27 million to develop a fluorspar mine in the Republic of South Africa, With fluorspar reserves at 20 million metric tons, the project is planned to produce 200,000 tons Per year of fluorspar for export starting in 1983. U.S.S.R. Resumes Sales of Titanium Sponge. - Against a background of increased U.S. titanium sponge supplies, the Soviet Union is offering limited quantities of this commodity to the U.S. market at approximately $10.00 per pound, down from $25.00 per pound last year.

Jan 1, 1981

By H. G. Wolfhard

The mode of propagation of explosions through narrow passages is important for understanding flameproofed equipment employed in mines. Narrow channels have been used in this investigation that connected between a small explosion chamber and a large chamber containing fuel-air mixture. The oxygen index of the mixture in the small chamber was determined which caused an explosion in the outer chamber. Preliminary measurements have already been given in Bureau of Mines Report of Investigations 5457 and suggested that) flames do not pass through narrow channels. The hot, burned gases from the explosion in the small chamber, however, are able to ignite the mixture in the large chamber by a process of hot-gas ignition. Systematic measurements are reported in the present paper that cover the influence of channel length and diameter and the properties of the gas mixtures in the large chamber on the transmission of explosions. The influence of such properties as quenching diameter and flame temperature is also discussed. This paper concludes the work on this problem and presents a theory that describes in detail parameters that influence transmission of explosions through narrow channels. INTRODUCTION Flameproofed equipment in mines is usually provided with flanges. A gap between the opposing flanges allows ventilation and release of pressure. The safe gap width has been determined for a number of flange lengths by Smith4/

Jan 1, 1959

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By K. O. Bennington

The thermodynamic properties of synthetic acmite, NaFe3+Si206, were determined by the Bureau of Mines. The enthalpy of formation was determined by hydrofluoric acid solution calorimetry. The values of the standard enthalpy of formation at 298.15 K, ?Hf°298.15, from the elements and from the oxides, ?H°298.15, are ?Hf°298.15 = -615.87 ±0.71 kcal/mole, ?H°298.15 (from oxides) = -32.08 ±0.53 kcal/mole. Various experimental data were combined with other data from the literature to calculate all the related thermodynamic properties in the range of 298 to 1,263 K. The standard Gibbs energy of formation is ?Gf°298.15 = -575.8 kcal/mole.

Jan 1, 1981

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Boone County, W. Va., as determined by the Bureau of Mines. It is one of a series describing the coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 6.3 million tons of coal was produced in Boone County, W. Va., in 1959, of which almost 5.5 million tons was mechanically cleaned in eight preparation plants. On December 31, 1959, it was estimated that almost 8 billion tons of coal remained in the county in beds 24 inches or more in thickness. Thirteen samples were collected from nine coalbeds and washability tests were made on these samples.

Jan 1, 1961

By James E. Hill

In the course of exploratory drilling during World War II by the Bureau of Mines under the Strategic and Critical Minerals investigations Program, a problem arose as to the ultimate disposal of the drill core resulting from that program. The difficulties experienced in obtaining factual information to evaluate mineral deposits examined (during that program) influenced the Bureau in a decision to catalog and store the drill cores for future reference. Initially, the drill cores were stored at the nearest Bureau of Mines station that had space available for the purpose. Recently the Bureau stations at Minneapolis, Minn., and Denver, Colo., were designated as the locations of permanent drill-core storage facilities. Drill cores that are retained from Bureau of Mines mineral-exploration projects are stored at these two locations and are given preference in selecting cores for storage. Drill cores are accepted also for storage from other Government agencies, State agencies, private companies, or individuals on the basis of available facilities and consistent with the significance of the core in relation to Bureau of Mines objectives and national interest. Selection and acceptance of such drill core are determined by the Bureau of Mines. The drill cores stored at the two locations are available for inspection by any person having a legitimate interest in the mineral deposits represented by the cores. Approximately 1,850,000 feet of drill core can be stared in the facilities now available to the Bureau of Mines. Approximately 475,000 feet of drill care is stored or scheduled for storage at Minneapolis, Minn., and 240,000 feet of core stored or scheduled for storage at Denver, Colo. A list of drill core now in storage at the Bureau of Mines core-storage facilities at Denver and Minneapolis is included as appendix A.

Jan 1, 1957

By W. P. Diamond

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over-burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

By Leon W. Dupuy

"INTRODUCTION Scheelite occurring in tactite at the Black Rock tungsten mine, near Benton in Mono County, Calif., was investigated by the Bureau of Mines in cooperation with the Geological Survey as part of their search for additional sources of supply of strategic minerals authorized under the Strategic Materials Act. 3/4/The work accomplished by the Bureau, and the assays of samples taken are described in this manuscript. The ore found aided materially in prolonging the operating life of the mine during the recent national emergency, supplying much-needed tungsten for war use. ACKNOWLEDGMENTSIn its program of investigations of mineral deposits, the Bureau of Mines has as its primary objective the more efficient utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual development work, and prepares the final report. The Metallurgical Division, under the direction of C. C. Ralston, chief, analyzes samples and performs beneficiatibn tests."

Mar 1, 1948

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Clarion County, Pa. Of the 15 samples collected, 1 was of metallurgical quality as received, 4 could be sufficiently upgraded to provide acceptable products, and the remaining 10 samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, 1 sample was of low sulfur content as received, 1 sample could be upgraded to low sulfur content, and 10 samples could be upgraded to medium sulfur content. The original sulfur content of the remaining three samples can be appreciably reduced by removal of the sink 1.58 specific gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1968

Improve the safety of mine workers by developing a sensitive ground-fault relay system capable of detecting and isolating low level ground faults and thereby minimize the danger of electrocution. Approach Inadvertent, direct contact with energized conductors in underground coal mines is a major cause of electrocutions. Although relay systems designed to protect workers against such fatal accidents do exist in some industries, there are no effective ground-fault-sensing relay systems that address the special problems presented by power systems designed for U.S. mines. The Bureau of Mines conducted research to design and construct a sensitive ground-fault relay for use with low-voltage, alternating current (ac) mine electrical systems. Such a relay, sensing current leakage or faults in an electrical system, would send a trip signal to a circuit interrupting device which would then shut down power.

Jan 1, 1986

By Robert E. Wood

[The temperature dependency of the low-density thermal conductivity coefficients, ?°T, of nitrogen, 100° to 1,200° K, is correlated with the Keyes' equation, ?T ½ -1 -12/T) WT = aT+ bT 10 The equation ?T,P = ?°T +a[ ]ß represented 509 experimental higher V pressure thermal conductivities in the temperature range 131.2° to 973.15° K for pressures to 500 atmospheres, with a mean absolute deviation of 2.35 percent. This equation was used to compute thermal conductivities of gaseous nitrogen for 47 pressures, 1 to 240 atmospheres, and 110 temperatures, 133° to 740° K, which are common to conditions encountered in Bureau of Mines helium purification processes. Isobaric heat capacities, CP, and viscosities, ?T,P, from previous work were combined with the present thermal conductivities, ?T,P, to compute Prandl1 numbers, C?T P / ?T ,P, of nitrogen. Tabular values of Prandtl num¬bers are presented for 49 pressures, 1 to 240 atmospheres, and 75 temperatures, 133° to 740° K. Estimated uncertainties are ±5 percent in the tabulated thermal conductivities and ±15 percent for the computed Prandtl numbers. However, the uncertainty may rise to ±10 percent for thermal conductivities and to ±30 percent for Prandtl numbers as the critical conditions of nitrogen are approached.]

Jan 1, 1971

By Lawrence W. Scott

This report presents several systems for continuously monitoring the quality of air in underground mines that are being developed by the Bureau of Mines. Underground stations measure methane, carbon monoxide and nitrogen dioxide concentrations, air velocity, and air temperature. This information is transmitted over a single telephone pair to central stations located on the surface. The central stations display alarms and the data is selectably displayed on digital panel meters.

Jan 1, 1977