Search Documents

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By T. L. Hebble

The Bureau of Mines investigated a hydrometallurgical procedure to recover Co, Ni, and Cu from an electrolytic zinc industrial copper filter cake. The copper filter cake is presently unmarketable or of low value because economic and environmentally acceptable processing technology is lacking. Research by the Bureau of Mines has developed a multistage process for recovering or recycling over 93 pct of the Zn, Cd, Cu, Co, and Ni from this material. The stages involved are (1) wet sizing, (2) H2S04 leaching of undersized material, (3) H2S04-Mn02 leaching of H2S04 leach residue, (4) selective precipitation of As, Cu, and Co-Ni products, and (5) precipitation of manganese for recycling to the leach circuit. The final process residue is only 1.6 wt-pct of the initial cake and consists of lead sulfate.

Jan 1, 1981

By Jingcheng Li

Currently many underground coal mines worldwide have installed or been planning to install a tracking system to trace miners mainly for their safety. Although many systems have been reported functional, a lack of sophisticated and systematic error correction methods apparently is still an issue for them; often it results in a low system resolution. To improve the system resolutions, this paper introduces two position adjustment methods for mine tracking systems. The first is an entry-matching method that optimally adjusts an off-course tracking device to the closest tunnel (entry). The second is a distance measurement adjustment method that accurately adjusts the position of a tracking device along an entry according to a measured distance from the device to a reference point. The coplanar node-path network mine model is used as the foundation for the development of these two methods.

Jan 1, 2009

By Ramie H. Thompson

1.1 BACKGROUND In many underground coal mining operations the use of electromagnetic field equipment, particularly communication systems, not only increases the overall efficiency of the mining operation but can be directly linked with mine safety considerations. The use of electromagnetic field producing equipment in underground coal mining operations can only be expected to grow. Several new communication systems have already been proposed. In addition, high-frequency producing equipments for many diverse uses in mining operations are under study. The use of these equipment in underground mining operations is hampered by the possibility of their electromagnetic fields interacting with the electric blasting cap operations commonly carried out in the mines. Such interactions can have at least two results bearing directly on mine safety: o premature initiation of the cap, either in its normal shot location or during hookup or transportation; o dudding of the cap so that normal firing operations do not cause irritation; thereby leaving unexploded high explosives after normal firing. Since the consequences of a premature initiation could, particularly in coal mines operations, result in catastrophe involving human life, the overall approach to prediction of possible hazard must be, as far as possible, of a "worst case" nature. The general problem of predicting possible RF hazards for any electroexplosive device (EED) is best treated by reference to Appendix A of

Jan 9, 1983

By Ronald H. Church, Walter E. Pittman, J. T. McLendon

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

By Thomas M. Barczak

Longwall roof behavior is characterized by strata displacements in both the face-to-waste (horizontal) and roof-to-f1oor (vertical) direc-tions. The roof support structure provides resistance to this motion by translation of these displacements into vertical and horizontal support loading. Observations indicate that the shield reacts with both a vertical and horizontal force to uniaxial convergence (displacement). However, there are different magnitudes depending on whether the displacement is vertical or horizontal. This makes it possible to use supports as monitors of strata activity and loading. The Bureau of Mines examined this behavior using a linear elastic model of the support structure with two degrees of freedom. Vertical and horizontal load reactions were related to associated displacement actions of the strata. This was done by determining the stiffness of the shield under controlled vertical and horizontal displacement motions in the Bureau's mine roof simulator. This report provides example predictions of strata convergence and isolation of horizontal support loading due to vertical roof convergence using the linear elastic shield model. The report also examines efforts to determine strata behavior by direct measurement of support displacement.

Jan 1, 1987

By Franklin B. W. Woodbury

The Bureau of Mines undertook the development and evaluation of a system to provide a simultaneous, on-line determination of both iron and silica in iron ore beneficiation streams as part of a program to improve the efficiency to mineral separation processes, Californium-252 (252-Cf) was the neutron source used in the system for measuring the amounts of silica and iron in bulk slurries by thermal neutron capture-gamma ray spectra analysis. The theory of thermal neutron capture-gamma ray reactions and their potential application to mineral processing stream analysis is discussed. The prototype system and supporting software developed by the Bureau is described. During the initial phase of the work, both simulated and actual pilot plant slurries were investigated using a 60-to 32-µg 252-Cf neutron source. The percent solids of the slurries was ranged from 2 to 40 percent and the silica and iron content ranged from 1.5 to 83 percent and from 10 to 65 percent, respectively. Accuracy of the determination of the components in the solids was dependent upon the percent solids in the slurry.

Jan 1, 1980

By J. F. Smith

A series of studies of emissions from large coal-fired steam generators have included measurements of the concentrations of oxides of sulfur and oxides of notrogen. The sampling equipment, method of sampling, and analytical techniques used for processing of these samples are detailed. A method based on the precipitation of benzidine sulfate was developed for determining both SO3 and total oxides of sulfur in the presence of interfering acidic components in the stack gases. In addition, difficulties encountered with sampling and analytical techniques are also described.

Jan 1, 1968

By Mary S. Esfandiary

This list of organizations that conduct research and development programs on coal has been compiled by the Bureau of Mines with the thought that such a directory may provide a useful guide to worldwide research efforts in the areas designated and may facilitate communication between organizations with similar interests. This list includes government, university, private, and commercial organizations. Many of these groups are conducting comparatively modest but often particularly interesting or specialized investigations. The areas of investigation have been defined in a broad manner--these include analysis and constitution, mining and geology, preparation, combustion, briquetting, high- and low-temperature carbonization, gasification, hydrogenation, Fischer-Tropsch, and health and safety. In some instances such information is not available, but the names of the organizations themselves often indicate immediate arias of interest. Special publications issued by and describing the work of each organization have been cited, when known; almost all of the organizations also publish results of their investigations in the technical press. Several foreign technical and trade publications that include such information and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. This list is not complete. Information that would improve coverage and/or accuracy will be welcomed by the Bureau of Mines.

Jan 1, 1961

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By J. J. Wallace

1. The Pittsburgh is the most important bed in Greene County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 6,011 million short tons as of January 1, 1954. Of this total, 5,967 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By D. S. Burgess

The characteristics of gas-phase detonations were observed in 20 instrumented firings within earthen tunnels, in 100 such detonations in a 24-in-diam by l63-ft-long steel pipe, and in about 200 smaller scale firings. Most of the fuels studied were representative hydrocarbons--acetylene, propane, gasoline, and a roughly equimolar mixture of methylacetylene, propadiene, and propane. In a pipe with two closed ends, the detonable limits were demonstrated to be very nearly the same as reported limits of flammability. The side-on impulses (pressures integrated over 200-msec intervals) were shown to be the same function of concentration regardless of whether deflagration or detonation had occurred. In a pipe with only the initiation end closed, the impulses of all fuel-air systems tended toward the same level when averaged over comparable ranges of fuel concentration; the lower pressures with saturated hydrocarbons were nearly compensated by longer durations of pressure transient. In all fuel-air systems, unexpectedly high impulses were obtained with slightly lean mixtures. In earthen confining structures, the impulse, of the explosion was efficiently converted into momentum of the failing wall. In the configurations studied, an earth velocity of about 20 fps was critical to overcome the soil's resistance to shear. The destructive effect was determined by gas pressure rather than by total energy release. The assignment of a "TNT equivalent" to an explosive gas mixture is discussed in terms of the confinement of the mixture.

Jan 1, 1968

By David S. Yantek

A-weighted sound levels around vibrating screens in coal preparation plants often exceed 90 dB(A). The National Institute for Occupational Safety and Health (NIOSH) is actively developing noise controls to reduce noise generated by horizontal vibrating screens. A 121-microphone, 3.5-meter-diameter array was used to perform beamforming to determine locations of significant noise radiation on the screen. Below about 1 kHz, the screen body was found to be the most significant noise source. The beamforming contour maps showed several key locations on the sides of the screen and the feedbox are the most significant contributors. Operating deflection shape (ODS) analysis was used to examine the screen behavior under actual operating conditions. This information is helpful in determining how to modify the screen body to reduce the noise radiated by the screen below 1 kHz. The analysis showed modal vibration patterns on the sides and feed box were the main contributors to noise. The results show several areas on the screen sides and feedbox that can be modified to reduce noise.

Jan 1, 2009

By A. B. Hooker, J. W. Paul

"There was a time when any suggestion that the Davy flame (safety) lamp be discarded, would have evoked unlimited, criticism. However, that time is past.Investigations both here and abroad have shown conclusively that the Davy lamp does not have the necessary factor of safety against ignitions of mine gas, and England, the lost stronghold of the Davy lamp in Europe, has eliminated this lamp and substituted safer types.In the United States there are companies who still use the Davy lamp in spite of all that has been said and published as to the dangers connected with its use.Recently the purchasing agent of an anthracite coal company requested the Department of the Interior, Bureau of Mines, to pass upon the safety of some braise gauzes for use in a shielded Davy lamp. A shielded Davy lamp is an ordinary Davy safety lamp equipped with a circular brass shield that is attached to the lamp posts. This shield extends about one-half way around the gauze and one-half of the gauze height. The main purpose of the shield is to prevent the lamps being extinguished by a sudden increase in the velocity of the air current past the lamp.The brass gauzes submitted for this test represented two grades of brass - a yellow brass and a red brass. The analysis of these brasses was not determined. Two shielded Davy lamps that were submitted for the tests each had a steel gauze. These steel gauzes were also tested. Tests were made in horizontally moving mixtures of Pittsburgh natural gas and air at velocities of 400 to 1,000 feet per minute. The gas percentages used were 7%, 8.6%, and 11%. Tests were made with the lamp shield in two positions relative to the lamp and direction of flow of the gas-and-air mixture. In one position the shield was between the gauze and flow, as normally used. In the other position the shield was on the downstream side of the lamp. The tests were continued until one or more failures or gas explosions been obtained with each of the six gauzes. The results of these tests summarized as follows:"

Jun 1, 1923

The results of a Feasibility and Design Study of Surface Impregnation Equipment to be used for Chemical Stabilization of Coal Mine Structures are described in this report. The study was sponsored by the United States Department of the Interior, Bureau of Mines, under Contract H0210055. This program was undertaken as an essential part of the Bureau of Mines Chemical Ground Stabilization Program. The responsible prime contractor was The Eimco Tunneling and Mining Machinery Division of the Envirotech Corporation. The Rocketdyne Division of the North American Rockwell Corporation performed part of the feasibility study and design and testing of the metering and feed system as a subcontractor to Eimco.

Jan 1, 1972

By L. A. Stewart

"SUMMARYThis paper describes most of the chrysotile-asbestos deposits of Arizona. Mining methods are discussed briefly and asbestos-mill flowsheets are incorporated. Arizona asbestos mines are the only sources on the American continents of naturally iron-free chrysotile spinning fiber that is so urgently needed for electric-cable coverings, especially on warships.Asbestos was first recorded and recognized in Arizona in 1872, and a minor amount was produced from a deposit in the Grand Canyon in 1900. The discovery of a deposit in the Salt River district in 1912 initiated intensive prospecting, and deposits soon were developed. The total Arizona production of all grades of asbestos through 1953 is estimated at 30,000 to 35,000 tons.The deposits of the Central Arizona region, which are discussed in this paper, are scattered over nearly 2,000 square miles. The annual output is relatively small, because the asbestos occurs in thin, discontinuous veins and only in areas where intrusions of diabase are adjacent to or crosscut certain favorable units of the pre-Cambrian Mescal limestone. This stratigraphic limitation, combined with other essential geologic conditions, tends to restrict the size of the deposits.Virtually all of the deposits are in rugged, mountainous country, and many of the mines are on steep canyon walls. In the average mine, production of 1 ton of commercial asbestos requires removal of 30 to 40 tons of waste rock. Mining and transportation costs consequently are high.Several deposits of chrysotile that is somewhat harsh and of moderate tensile strength have been known for years but were not worked because of the former exacting demands of industry for high-strength, soft asbestos. However, improve¬ments in asbestos fiberization and spinning technique, combined with the urgent need for asbestos, have made this so-called semisoft fiber desirable, and deposits of this type now are being exploited."

Jan 1, 1955

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Thomas M. Barczak

This U.S. Bureau of Mines report describes methods to enhance the capacity, stiffness, and timber utilization of wood crib supports. Since stiffer supports minimize strata deflections that contribute to roof instability, efforts to maximize crib stiffness while maintaining stability through a wide displacement range should be a design priority. The stiffness and capacity of conventional crib designs, employing alternating layers of wood timbers that are loaded perpendicular to the grain, can be increased by increasing the interlayer contact area or by using higher strength wood. Contact area can be increased by using wider timbers or employing more timbers per layer. Concepts that provide parallel-to-the-grain timber loading will provide substantial increases in crib stiffness and capacity. Two concepts that utilize this principle are examined: (1) an original South African design that constructs wood cribs from preformed layers (mats) of timber where short blocks are oriented vertically between horizontal slabs; and (2) a design that employs full lengths of timber placed vertically in the interior of a conventional crib structure. These designs also provide more efficient timber utilization by providing greater support capacity per volume of wood used in the crib construction.

Jan 1, 2010

By J. H. Weber

This Bureau of Mines publication describes the hardware system and software package for the semiautomatic acquisition and automatic processing of high-resolution mass spectrographic plates. The semiautomatic data acquisition allows a tenfold saving of time compared with manual data acquisition. Automatic processing of the high-resolution data to yield exact masses, intensity, and the corresponding empirical formulas is accomplished by efficient programming on a small, inexpensive, programmable calculator system.

Jan 1, 1974

By Alexander May

In its role to provide technology to prevent or limit adverse environmental impacts associated with mining or minerals processing, the Bureau of Mines has conducted research at its Tuscaloosa Research Center to asess the environmental impacts of phosphogypsum produced by the Florida phosphate industry. Over the years, stockpiles containing 335 million tons of phosphogypsun have accumulated and the industry continues to generate an additional 33 million tons a year. Samples from approximately 1,000 feet of drill core, obtained from nine stockpiles were characterized using chemical, X-ray diffraction, emission spectrographic, radiological, and physical means. The data developed indicated that phosphogypsum is not a corrosive or toxic hazardous waste as defined by Environmental Protection Agency criteria. Radium concentration averaged 21 picocuries per gram and its content was inversely related to particle sizes. Thirty-nine elements were detected in phosphogypsum; concentrations of these elements did not vary with depth within the stockpiles.

Jan 1, 1982