Search Documents

By J. J. deBarbadillo

This Bureau of Mines report describes a process for recovering chromium and other metals from superalloy scrap. Laboratory-scale experiments were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the fonnation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallurgical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and iron-molybdenum residue. Recovery of the principal elements contained in the scrap is chromium--93 percent, nickel--99 percent, cobalt--96 percent, and molybdenum--92 percent.

Jan 1, 1981

By B. J. Moore

This publication contains analyses and related source data for 256 natural gas samples from wells and pipelines in 17 States. All of the samples were obtained and analyzed during calendar year 1977 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Nineteen previous publications have presented the results of 11,317 gas analyses prior to 1977. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 16

Jan 1, 1978

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By Stephen D. Cramer

The objective of the present studies was to develop thick adherent and coherent coatings of platinum and palladium on refractory metals and other substrates of industrial and engineering importance. Existing platinum and palladium electrolytes were modified to make them suitable for the electrodeposition of thick deposits. The optimum operating conditions for these electrolytes were established. Pretreatment procedures for columbium, copper, graphite, molybdenum, nickel, stainless steel, tantalum, titanium, tungsten, vanadium, and zirconium substrates were studied. New pretreatment procedures for columbium, molybdenum, stainless steel, tantalum, tungsten, and nickel were developed. The internal stress and hardness of selected electrodeposits were measured. The effects of heat treatment upon the properties of electrodeposits were studied.

Jan 1, 1967

By R. J. Leary

A small electronic digital computer employing punched cards has been used to facilitate the solution of a variety of problems in Bureau of Mines pyrometallurgical research. In this work the computer has been found to be economical for solving both simple problems that occur repeatedly and those involving complex or iterative calculations. Each of these classes of problems and their respective solutions are described. These small computers can be used effectively by researchers when they work in consultation with a computer specialist. Close team work produces the required solutions in less time, and, oftentimes, in a more useful form. Participation in programming by researchers develops in them a skill for evaluating the suitability of problems for electronic computing.

Jan 1, 1960

By R. V. Ramani, J. Qin

"In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration. INTRODUCTIONA detailed experimental study on the characteristics of longwall dust cloud in operating longwall faces has been reported by Ramani, Qin, and Jankowski (1991). The study indicated that there are several important factors whose effects on dust transport in longwall faces need to be further investigated. In an operating longwall face, the effect of these parameters could not be easily isolated as control over the affecting parameters is not readily possible. In a simulated longwall face, however, these parameters can be controlled. Therefore, as a follow-up to the field study, a series of controlled experiments were conducted in a full scale simulated longwall face in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines [Qin, 1992]. Specific aspects which were addressed during the experimental design phase included determining the types of samples to be collected, selecting proper instruments to collect these samples, and developing detailed sampling and time-study plans to correlate the dust concentrations with face activities. Two types of dust--anthracite and bituminous--were used. Dust dispersion rate into the air as well as the source dust particle size distribution were documented. Control was exercised over both air velocity at the face and air leakage along the longwall face. During experiments, the dust source was moved to simulate the shearer movement at operating longwall faces. Detailed descriptions of the design of experiments, experimental results, and data analyses follow in the subsequent sections."

Dec 1, 1996

As part of remote sensing research on an abandoned mine lands (AML) site in the Colorado Springs, Colorado area, a geographic information system (GIS) database was generated. This GIS database contains information on the locations and extents of abandoned underground coal mines, the geology of the area, subsidence features and degrees of subsidence risk, topography, drill hole locations, and lineaments (linear features) related to subsurface geologic structures. A GIS database allows the reproducible and accurate comparison and analysis of any data sets which geographically overlap and are within the same coordinate system. The database has been released to the public domain so that government agencies, researchers, educators, and the general public can access this coherent database for the purposes of better understanding the study area and GIS technology. Data files and maps are available in formats that are compatible with the GIS software used in the research project and with most CAD systems so that as many people as possible can make use of the majority of the database. This document serves as the data dictionary for the database by providing descriptions and origins of the data files.

Jan 1, 1992

By R. J. Campbell

[The steady increase of aluminum production means a corresponding increase of carbon consumption in the alumina-reduction cells. Improved petroleum techniques constantly reduce the amount of byproduct petroleum-coke production. These, trends threaten the alumina-reduction works with possible shortages of carbon, which must be supplied from some other source. In anticipation of this shortages, an investigation into the possibility of using coal as an alternative source of carbon was begun at the Northwest Experiment Station of the Federal Bureau of Mines. The investigation lit has developed bench-scale methods that produce carbon of higher purity than is required by specifications for anode carbon. Additional work will b required to bring these processes to pilot-plant seals and to prove the suitability of the carbons, produced or aluminum-anode consumption.]

Jan 1, 1956

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment: including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that arc recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel al the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By R. V. Lundquist

The Bureau of Mines made a laboratory study of the amenability of anorthosite rock ( from the San Gabriel Mountains , Los Angeles County , Calif . ) to treatment by the lime soda sinter process for the extraction of alumina . The study was done under a cooperative agreement with the California Division of Mines and Geology . This report presents the results of the investigation , and it includes a review of the geology of the deposit ( 7 ) by Dr. Gordon B. Oakeshott . Interest in the recovery of alumina from submarginal aluminum silicate ores is stimulated by the fact that the domestic aluminum industry depends on imports of bauxite for its alumina requirements . Of the 8.0 million long dry tons of high - grade bauxite consumed in 1961 for producing metallurgicalgrade alumina , only 0.9 million long tons , or 11 percent , was mined in this country . During past years many organizations have carried out research programs to determine if alumina could be extracted economically from such domestic ores as clays ( 3 , 4 ) , anorthosite ( 8 ) , and other silicate sources . Successful alumina extraction is the ultimate objective of the Bureau of Mines program.

Jan 1, 1963

By Murray Weintraub

In an investigation of the incineration of combustible wastes, the Bureau of Mines studied the effect of dimensional parameters, process variables, and fuel properties on the operation of an incinerator that consisted of a single cylindrical combustion chamber in which all combustion air was supplied tangentially above the fuel. Construction and operation of three designs of such a device proved that the tangential overfire air design is effective in providing efficient combustion and low concentration of particulate matter in the effluent gas. A correlation was found that related burning rate with air rate, chamber diameter, and inlet port diameter. In one of the incinerator models, ignition was by radiation from a preheated surface. The temperature of this surface was required to be 1,400° to 1,600° F to insure ignition of moist refuse; however, this had little effect on combustion rates. In the combustion of moist refuse, evaporation of the water proceeded through the fuel bed as a wave, with an ignition wave following the evaporation.

Jan 1, 1967

By A. W. Decora

Gas-liquid chromatography has been applied to separating basic nitrogen compounds, such as pyridines and amines. Close-boiling compounds have been separated by exploiting structural and polarity differences, using selective liquid substrates dispersed on specially prepared solid supports. Development of these special supports was necessary in order to obtain symmetric peaks for basic nitrogen compounds; solution of this problem was important in applying gas-liquid chromatography to the analysis of basic nitrogen compounds found in shale oil. Attempts to analyze shale-oil tar bases by conventional gas-liquid chromatographic techniques, using Chromosorb4/ or Celite 545 as the support for a nonpolar liquid substrate, resulted in asymmetric peaks. These asymmetries were caused by adsorption of sample vapors on the solid support. Symmetric peaks were obtained when strongly polar liquid substrates were used on either Chromosorb or Celite. However, a solid support giving symmetric peaks only with strong polar substrates restricts the choice of substrate, and frequently, desired separations cannot be achieved.

Jan 1, 1961

By A. Landsberg

Kaolinitic clays are potentially a vast domestic resource for aluminum. Utilization of this resource could decrease or eliminate the nearly complete dependence of the United States on foreign raw materials for this important metal. Furthermore, processing of clay to aluminum through anhydrous chloride metallurgy could reduce the high electrical energy requirements of the conventional Hall-Heroult aluminum reduction process. Several anhydrous chloride processes have been proposed; however, unresolved technical problems have prevented their commercialization. In particular, an acceptable chemical means has not been found to extract aluminum from clay as a highly pure anhydrous aluminum chloride. This Bureau of Mines report identifies and discusses the important chemical problems involved in achieving an acceptably rapid, self-heating, selective chlorination reaction and the subsequent separation of iron chloride byproduct from the anhydrous aluminum chloride.

Jan 1, 1983

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

By W. F. Marshall

This report describes exhaust-emission data from 10 diesel engines: six 4-cycle, direct-injection, naturally aspirated engines; two 4-cycle, direct-injection, turbocharged engines; one 4-cycle, precombustion-chamber, turbo-charged engine; and one 2-cycle, direct-injection engine. These engines were tested over a 3-year period (1968-70). Lowest emissions were obtained with a precombustion-chamber engine. Emissions from the 2-cycle, direct-injection engine fell within the range of emission rates for the 4-cycle, naturally aspirated, direct-injection engines. Excluding the precombustion-chamber engine and excepting one of the 4-cycle, naturally aspirated engines, carbon monoxide emission rates were about the same for all engines tested. Test data on smoke, odor, and emissions of hydrocarbons, oxides of nitro-gen, carbon monoxide, and aldehydes are given.

Jan 1, 1971

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with tie intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980

By J. A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since the early 1980's, the U.S. Bureau of Mines has conducted numerous studies in underground and surface coal mines to identify the sources of quartz dust and its fundamental characteristics. This report presents data and conclusions obtained from these studies. The two most significant quartz dust sources were found to be the continuous miner excavating rock and the highwall drill operating in a rock overburden. The percentage of quartz was found to be higher in the smaller size fractions of dust when significant amounts of rock were mined by the continuous miner. Another factor theorized to affect quartz dust generation and size characteristics is the morphology of the quartz-bearing rock. Several laboratory studies were conducted to investigate capture efficiency of water spray technology and flooded-bed scrubbers with respect to the particle size of the dust. Water sprays and flooded-bed scrubbers were both found to be less efficient on smaller dust particles, and the scrubber was particularly less efficient on quartz dust. These results indicate that quartz control technology should be directed at controlling smaller sized dust particles.

Jan 1, 1990

By K. K. Kelley

Sodium-aluminum and potassium-aluminum silicates are among the more important rock-forming minerals of the earth's crust. They also appear as constituents of some metallurgical slags and of some refractory materials. Consequently, knowledge of their thermodynamic properties is interesting and valuable from several viewpoints. This paper reports experimental determinations of the low-temperature heat capacities and entropies at 298.16° K. of albite, jadeite, and nephelite it the sodium-aluminum silicate series and of adularia, ferriferous orthoclase, leucite and kaliophilite in the potassium-aluminum silicate series. Also high-temperature heat-content and entropy increments about 298.16° K. are reported for albite, jadeite, nephelite, and carnegieite in the sodium-aluminum silicate series. Except for a few high-temperature heat-content values for albite, all these data are available for the first time.

Jan 1, 1953

By Diane Schwegler-Berry, Vincent Castranova, Chang-geng Moe, Jane Y. C. Ma, Mark D. Moore, Joseph K. H. Ma, Carl J. Malanga, Ji-Hee Kane

"Effects of Bisbenzylisoquinoline Alkaloids on Alveolar Macrophages: Correlation between Binding Affinity. Inhibitory Potency and Antifibrotic Potential. CASTRANOVA, V., KANG, J-H., MA. J. K. H., Mo, C-H., MALANGA, L. J., MOORE M. D., SCHWEGLER-BERRY, D.. AND MA. J. Y. C. (1991). Toxicol. Appl. Pharmacol 108, 242-252. The Chinese have conducted extensive studies concerning the medicinal properties of plant products. In this investigation the ability of three bisbenzylisoquinoline alkaloids to inhibit particle-induced activation of alveolar macrophages was evaluated and this inhibitory potential was correlated with the ability of those drugs to bind to membrane components. Tetrandrine. i.e.. an herbal medicine used as an antifibrotic agent in China, was a potent inhibitor of particle-stimulated oxygen consumption, superoxide release, and hydrogen peroxide secretion by alveolar macrophages. Tetrandrine also exhibited substantial binding affinity for membrane lipids and alveolar macrophages. In contrast, tubocurine, an analogue with little antifibrotic potential, exhibited low binding affinity and had little effect on macrophage activation. Methoxyadiantifoline, an alkaloid of unknown antifibrotic potential, exhibited inhibitory and binding properties similar to those of tetrandrine. The data indicate that a strong relationship exists between the antifibrotic potential of these alkaloids and their ability to bind to alveolar macrophages and inhibit particle-induced activation of these phagocytes. These drugs should serve as useful probes to evaluate the role of alveolar macrophages in pulmonary fibrosis. © 1991 Academic Press, Inc.Chronic silicosis is a fibrotic disease resulting from occupational exposure to silica dust. It is manifested initially by an increase in the quantity of pulmonary surfactant (Dethloff et al., 1986). However, in later stages it is characterized by an increase in collagen formation and the development of concentric hyalinized nodular lesions in the lung (Ziskind et al., 1976). Although mechanisms for the progression of silicosis have not yet been completely defined, activation of alveolar macrophages by respirable silica particles is believed to play an important role in the etiology of this disease. Studies from our laboratory have shown that both in vitro and in vivo silica exposures result in a stimulation of macrophage release of reactive products capable of damaging the lung parenchyma (Castranova et al., 1990; Goodman et al., 1990). In addition, exposure of al¬veolar macrophages to silica results in the release of fibrogenic factors which enhance the proliferation of fibroblasts and the synthesis of collagen by these pneumocytes (Leibovich and Ross, 1976; Bitterman et al., 1982, 1983).The bisbenzylisoquinoline alkaloids, which represent the largest group among the iso-quinoline compounds isolated from the plant kingdom, are known to exhibit a broad rangeof pharmacological activities. Tetrandrine, for example, an alkaloid isolated from the root of Stephania tetrandra, has been tested for its antitumor, antihypertensive, and antisilicotic effects (Kupchan and Atland, 1973; Zeng et al., 1985; Yu et al., 1983). It is currently used in China as a treatment for angina, hypertension, and silica-induced pulmonary fibrosis (Li et al., 1981). Several related bisbenzylisoquinoline alkaloids such as methoxyadiantifoline and tubocurine have also been evaluated for medicinal effects. Methoxyadiantifoline has been shown to exhibit effects on the cardiovascular system similar to those reported for tetrandrine (Jia et al., 1988). However, to date, the antifibrotic activity of methoxyadiantifoline has not been evaluated. In contrast to tetrandrine, tubocurine, a structural analogue of this drug, has been reported to be relatively ineffective against fibrosis (Mo et al., 1982)."

Mar 1, 1992