Search Documents

By M. H. Stanczyk, I. L. Feld

Dewatering of typical Florida phosphate rock slime by electro - osmotic techniques was investigated to determine if a compacted , plastic solid product could be obtained with simultaneous recovery of the water for re - use . Tests with porous cathodes and rod - type anodes imbedded in dilute slime charges of up to 4 tons in weight showed that the slime could be dewatered to about 35 percent solids . The dewatered products had the consistency of modeling clay . In the large - scale tests using 2.5 - foot electrode spacings , about 21 kilowatthours of power were consumed per ton of water removed in thickening the slime from 17 to 25 percent solids , but the rate of water removal was so slow that the process was not considered commercially feasible . Other tests made with electrode spacings of from 2.5 to 8 feet showed that more rapid dewatering could be obtained but that the power required was excessive . However , for special uses such as stabilizing slime pond dikes where the cost of dewatering might not be a prime requisite , high voltages could be used to rapidly remove the water . Tests of 400 - pound slime charges using a combination of electroosmosis and vacuum filtration showed that the rate of dewatering could be expedited . The average power required to thicken a ton of slime from 15 to 35 percent solids was 5 and 50 kilowatt - hours when operating the electroosmotic filtration cell at potentials of 20 and 100 volts , respectively . calculated filtration area of about 10 square feet per ton of slime treated per day was required to thicken the slime from 15 to 35 percent solids .

Jan 1, 1964

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By A. J. Leighton

An improved mathematical model with the attendant computer program to calculate multiphase fluid flow in petroleum reservoirs is presented. The model is used to simulate the behavior when a fluid is used to displace hydro-carbon fluids in a reservoir. The method is an expansion of a previously published method, in Bureau of Mines RI 7011, but handles constant injection rate as an alternative to constant pressure. Program documentation is provided along with thorough explanations of the added program features. Using the program, the petroleum engineer can calculate oil recoveries for different flood patterns and operating conditions and select the conditions most likely to optimize recovery. Experience with the previous model demonstrated the need for the improvements in order to simulate reservoir behavior more accurately. The improved method will result in improved oil recovery. In this paper, the significant improvements are described in detail so that anyone interested can put the program to use.

Jan 1, 1975

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

A series of economic evaluations of processes for producing metallurgicalgrade alumina from low- grade aluminous materials is being conducted by the Bureau of Mines to determine the relative processing costs . The two processes considered in this evaluation are concerned with the recovery of alumina from clay through the formation of ammonium alum . In the first process , dehydrated clay is leached with ammonium bisulfate solution ; in the second process , clay is baked with ammonium sulfate and then leached with water containing a small quantity of sulfuric acid . After the alumina is dissolved by either of these methods , the iron is reduced to the ferrous state to avoid crystallization of ferric sulfate with the alum . The recovery of pure alum requires two crystallization steps . The alum crystals are then redissolved and precipitated with ammonia to produce alumina hydrate , which is calcined to a - alumina . These evaluations are based on published work , and the proposed plants are designed for a capacity of 1,000 tons of alumina per day . The estimated operating cost per ton of alumina for the bisulfate leaching process is $ 117.06 , and for the sulfate baking process , $ 109.26 . Using a Marshall and Stevens chemical equipment index basis of 240.0 , the estimated fixed capital costs , in the same order , are $ 158 million and $ 146 million . Under current economic conditions , these two processes are not competitive with the Bayer process for the production of alumina from bauxite . Since small improvements will not reduce costs sufficiently to approach competitive costs , future research work with these processes should be confined to areas likely to result in major cost reductions .

Jan 1, 1965

By F. E. Griffith

Cost data are given for five methods of secondary backfilling of strip mines previously partially backfilled. The operations were conducted in north-central Pennsylvania; an average of 600 linear feet of highwall were backfilled in each trial. Major obstacles and the relative merits of the methods are discussed.

Jan 1, 1966

By Edward D. Thimons

This Bureau of Mines report presents expected levels of air pollutants in the face areas of oil shale mines, based upon data collected by the authors and previous investigators. Ventilation requirements to maintain these pollutant levels below their threshold limit values and Federal and local mine air quality standards are discussed. Two practical face ventilation systems are discussed in terms of actual in-mine test experience.

Jan 1, 1986

By Henry E. Perlee

In a Bureau of Mines study two-dimensional mathematical equations were solved that describe the transient thermal response of a rock dust particle in a cloud of similar particles in a gas flame's preheat zone subject to a radiant field from the approaching flame. The description includes both radiant energy absorbed and emitted by the particle and thermal conduction inside the particle and into the surrounding gas environment moving relative to the particle. Two situations were studied; in one the radiant energy incident on the particle is converted to thermal energy at the particle surface, and in the other the radiant energy is converted to thermal energy uniformly over the volume of the particle. The result of the study showed that for a 10-µm-radius particle, a 200-mg 1-1 loading density, and a flame approach velocity of 30 m sec-1, the particle temperature rise was twice that previously calculated by Singer and Cook based on the model of Essenhigh and Csaba. It was further established that under the conditions examined a rock dust particle temperature never increases more than about 200 K before crossing the flame front.

Jan 1, 1976

By Charles W. Huggins

To determine the nahcolite and dawsonite content in oil shales, the Bureau of Mines compared X-ray diffraction, infrared spectroscopy, thermal methods, and a previously published method by Smith and Young based on the selective solubility of sodium compounds. The Smith and Young method and a new method based on the weight of carbon dioxide produced by thermal decomposition are recommended for determining nahcolite. X-ray diffraction and the Smith and Young method are recommended for determining dawsonite. X-ray diffraction, infrared spectroscopy, and differential thermal analysis were useful for identifying other minerals in the samples.

Jan 1, 1973

By R. H. Lien

The Bureau of Mines developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. The modified citrate process involves absorption of sulfur dioxide (S02) in a buffered citric acid solution. The S02-loaded solution is regenerated by countercurrent contact with steam in a packed tower. The wet S02 product is then dried and can be liquefied or further processed to make sulfuric acid. Test data from process investigation unit studies are presented. Material balances, flowsheets, and cost estimates are given for recovering S02 from copper smelter reverberatory gas, lead smelter sintering machine tail gas, and power-plant stack gas. Operating cost estimates show the process will add $0.04 per pound of copper, $0.01 per pound of lead, and $0.015 per kwhr to the cost of the respective operations. These costs could be substantially reduced if a source of waste heat was avail-able to provide the process steam requirements.

Jan 1, 1982

By Charles B. Kenaban

The possibility of using ultrasonic energy as a tool to improve the electrolytic deposition of copper and zinc from several electrolytes was investigated by the Federal Bureau of Mines. Sound with frequencies of 20, 26, 38, and 400 kilocycles per second and acoustical intensities of 0.25 to 1.5 watts per square centimeter was employed. Measurements of cell voltage, anode and cathode current efficiencies, and electrode potentials were made at various current densities. Effects of ultrasonics on the quality of the deposit and on anode corrosion also was noted. In the electrolytic recovery of copper from an acid copper sulfate solution at 50° C., adherent, well-consolidated deposits are normally obtained up to a current density of 30 amperes per square foot. As the current density is increased above this value, the deposits normally become progressively more spongy and less adherent. Ultrasonic irradiation resulted in adherent and well-consolidated deposits at current densities up to 300 amperes per square foot. Radiation also produced smaller grain size and preferred orientation of the copper crystals. In addition, radiation caused as much as 3-volt decreases in cell voltages at the higher current densities. These decreases were caused chiefly by depolarization of the anode, although small depolarization effects were also noted at the cathode. Radiation apparently did not greatly affect cathode-current efficiencies, but prevented excessive anode corrosion at the higher current densities and resulted in more uniform corrosion. Ultrasonic radiation at a frequency of 400 kilocycles per second was not as effective as radiation at the lower frequencies. Circulation of the electrolyte at rates up to 5 percent of the cell capacity per minute did not produce results comparable to those effected by ultrasonic radiation. Rapid rotation of the cathode up to 1,800 revolutions per minute gave results approaching those obtained with ultrasonics.

Jan 1, 1961

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

By John H. Hild

This is a report on work done and results obtained in a minerals exploration program conducted by the Bureau of Mines on the lead-zinc deposits in the Ross Basin-Lake Como district, San Juan County, Colo., in 1948, 1949, and 1950. Four large veins--the Seven Thirty, Red Rogers, Cashier-Shorts top-Canandaigua, and Queen Anne--and several narrow spur veins were explored at relatively shallow depths with core-drill holes. Thirty-nine holes, totaling 10,491.5 feet, were drilled, and the core samples were assayed at the Bureau of Mines station at Salt Lake City, Utah.

Jan 1, 1959

By George Saliba

This report disucsses the formulation of a mathematical model for the steering of a conveyor belt by a flat return idler and a troughed idler under various loading conditions. Significant parameters associated with belt training are identified. The generation of a skewed flat return idler model in terms of a steering force and self-aligning torque is presented. Development of the mathematical model for the flat return steering idler is illustrated for the case of no circumferential slip occurring and for the assumption of a bidirectional slip mechanism. Experimental results supporting the theoretical analysis is presented.

Jan 1, 1977

By George S. Rice

A novel method of extinguishing a mine fire in a stowed or gob-filled area by employing liquid carbon dioxide under high pressure eras used recently with success at the President (Prasident) coal mine, Bochum, Germany, as reported by P. Cabolet in Gluckauf (Apr. 24, 1937, p. 393) The use of carbon dioxide gas as a fire-fighting agent in surface plants and in ships is now general practice in the United. States, but when it has been tried for extinguishing fires in mines in large areas more or less confined by stoppings it has not been successful. Examples of the latter method of attempting to fight mine fires are given in Bureau of Mines Bulletin 229, Fifty-Nine Coal-Mine Fires; How They Were Fought and That They Teach, by G. S. Rice, J. VT. Paul, and 14. VT. von Bernewitz (1927). The reason for its nonsuccess may be either that the stoppings are not tight or that the roof and pillars are more or less fissured and enough air passes into the area to sustain a slow fire, whether of spontaneous origin or produced by gas explosion or other source of ignition.

Jan 1, 1937

By R. C. Buehl

A pyrometallurgical process for recovering manganese from open-hearth furnace slags or low-grade manganiferous iron ores is described. The slag or ore is smelted in a blast furnace to produce spiegeleisen; the speigeleisen is then blown with air in a basic converter to give an oxide slag. This slag product contains 60 to 75 percent manganous oxide and may be considered a synthetic manganese ore. In the smelting operations coke rates for five test periods ranged from 3,255 to 4,130 lb per ton of spiegeleisen. The recovery of manganese in the spiegeleisen varied from 60 to 76 percent. Recovery increased to 83 percent when the open-hearth slag feed to the blast furnace was diluted with a high-? grade iron ore sinter to facilitate smelting. In blowing the spiegeleisen a cyclic procedure was developed that gave nearly 90 percent recovery of manganese in the slag product (synthetic ore) yet prevented excessive contamination of the slag by phosphorus and iron. The overall recovery of manganese was about 75 percent when iron ore sinter was used with the open-hearth slag in the smelting step. The metal remaining after oxidizing the manganese from the spiegeleisen contained approximately 3.5 percent phosphorus. It was refined in a basic converter by blowing with air in the presence of lime" A high--grade iron and a basic phosphate slag were produced.

Jan 1, 1965

By Abdo F. Bayazeed

A survey of the underground injection of steel processing waste pickle liquor (WPL) was made by Bureau of Mines engineers. Hydrochloric and sulfuric acids WPL are being injected into deep wells completed in the Cambrian age Mt. Simon Sandstone Formation in Illinois and Indiana. The Mt. Simon Formation ranges up to 1,800 feet in thickness. The average depth of WPL injection wells is 4,000 feet, and injection is mostly by gravity flow at rates as high as 4,000 barrels per day. The details of the design and operating history of a WPL well located near Gary, Ind., are discussed. Laboratory tests showed that the Mt. Simon Sandstone is sensitive to fresh water. The adsorption of iron and neutralization of acids by sandstone cores from deep wells and an outcrop were determined.

Jan 1, 1973

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z2 measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 2010

By Loren R. Anderson

This is an Appendix of Volume I. It contains the results of the electric cone penetrometer soundings from the first phase of the testing program.

Jan 1, 1982

By Irving Wender

The oxo reaction consists of catalytic conversion of olefins by reacting the olefins with CO and H2 (water gas) to aldehydes that contain one more carbon atom than the starting olefin. The aldehydes are then generally reduced with hydrogen to primary alcohols in a second stage. The two-stage process is called the oxo process. The word "oxo" is derived from the German "oxierung" (ketonization); thus the exact English equivalent of "oxo" is "keto". The oxo process may be applied to nearly all olefins. A wide range of pressures and temperatures may be used in both stages. The pressure range usually employed is 150 to 200 atmosheres. The temperature in the first stage is usually about 140° C. and in the second or hydrogenation stage about 180° C. Although a standard Fischer-Tropsch catalyst may be used for both steps, cheaper catalysts have been utilized to effect hydrogenation of the aldehydes. Most of the information for this, report on the oxo process was gathered from Technical Oil Mission microfilms. T.O.M. Reels 14, 55, and 134 were especially valuable. T.O.M. Report 6 by H. M. Weir was very helpful. Information on the oxo process is scattered throughout documents captured in enemy territory, and the present report does not include all the available data. Some of the information was procured by personal interview. Where, in the body of this report, certain investigators are quoted, the source of the statement is either personal interview or the T.O.M. reports.

Jan 1, 1948