Search Documents

By Ronald P. Hollenbeck

The value of mineral production in Alabama increased 1 percent above the record high set in 1965. Alabama ranked second among the States in the production of bauxite, third in the production of masonry cement, native asphalt, and scrap mica, sixth in the production of portland cement, ninth in the production of iron ore, and tenth in the production of lime. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacturing of cement, and the production of crude petroleum. These industries accounted for 87 percent of the State's total value of mineral production, compared with 85 percent in 1965.

Jan 1, 1967

By R. J. Evans

The generation and disposal of solid waste from electric utility plants using a lime or limestone wet-scrubbing system and the potential effects on the environment were estimated for 1975 and 1980. The study indicated that in 1975 approximately 5.8 million tons of desulfurization solid waste (50 percent solids) will be generated. In 1980, when it is estimated that desulfurization will become commercially accepted, approximately 71.4 million tons of this material will be generated for disposal and/or utilization. The desulfurization waste material when combined with lime, fly ash, and water may have potential for use as a roadbase material, landfill reclamation, and synthetic aggregate.

Jan 1, 1974

By D. R. Tesarik

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars), and biaxial stressmeters (to measure stress changes in several support pillars and abutments). Two-and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 2010

By E. K. Kleespies

The Bureau of Mines demonstrated a technique for electrowinning titanium from titanium nitride and titanium dioxide. Titanium-nickel-copper metal solutions containing 26 to 61 weight-percent titanium were prepared by electrolyzing titanium nitride in molten mixtures of potassium fluotitanate) and sodium chloride or barium chloride and depositing titanium on nickel-copper cathodes. A titanium-nickel alloy was prepared by electrolyzing titanium dioxide in an electrolyte of potassium fluotitanate) sodium fluoride) and calcium fluoride and depositing titanium on solid nickel cathodes. This alloy contained 21 weight-percent titanium and had a combined oxygen-carbon content of less than 0.1 weight-percent. A compartmented cell confined the oxide feed near the anode and inhibited oxygen contamination of the metal.

Jan 1, 1966

By C. Thomas Hillman

This Bureau of Mines report describes an investigation of factors influencing economic viability of a proposed system to mine and process manganese nodules. The system consists of hydraulic dredging and ammonia leach processing designed to recover three metals: nickel, copper, and cobalt. A ferromanganese recovery plant is a considered option. Annual capacity is 3 million dry metric tons (t) nodules. Aftertax rates of return (ROR's) of only 7.38 and 6.63 pct are predicted for three-and four-metal base scenarios, respectively. Sensitivity analyses indicate that variations in commodity prices, metal recoveries, and deposit grades produce similar incremental changes in ROR. Estimated cumulative effects of price variations are greatest. While three-metal operations generally yield higher predicted returns, potential increases in manganese price and process recovery could make four-metal operations most profitable. Maximum variations in both capital costs and three-metal operating costs result in ROR changes of about 25 pct. In contrast, four-metal ROR's exhibit variations to 70 pct. Even so only a best case analysis, utilizing favorable variations in all categories tested, generated ROR's approaching a level thought necessary to trigger company interest. Consequently, it is concluded that nodule mining will not take place in the foreseeable future without significant financial incentives.

Jan 1, 1985

By Robert H. King

An analysis of low-voltage shielded trailing cables is performed to develop a method for calculating the differences in operating costs between shielded and non-shielded cables. Two types of shield constructions are considered (SH-C and SH-D) for the three major underground coal mining methods. Data from laboratory and in-mine testing are presented in addition to an analysis of safety benefits. Recommendations for further investigations are proposed. Example calculations with sensitivity analyses are presented. Recommendations for further investigation include costs impact considerations.

Jan 1, 1980

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By G. H. Keith

The Bureau of Mines determined the mechanism(s) involved in observed anomalous changes in mechanical properties of vanadium-base alloys. Tensile properties of electrorefined and commercial-purity vanadium-base alloys containing up to 5 atomic percent molybdenum or titanium were measured between 77° and 673° K. Snoek oxygen and nitrogen peak heights were measured to determine the changes in dissolved interstitial content caused by increasing quantities of solute. In addition, changes in lattice parameter were followed wit: precision X-ray techniques. Softening, observed in alloys containing titanium, is explained by the formation of a second-phase titanium compound with oxygen or nitrogen. However, because of partitioning of titanium between compound formation and solid solution formation, about five times the stoichiometric amount was required for complete reaction. Addition of 1 percent titanium drastically lowered the strengthening due to strain aging, at 673° K, and 2 percent titanium essentially eliminated it. All alloys were ductile at 77° K. Variations in the tensile properties of the molybdenum-containing alloys are explained by variations in the amounts of interstitial impurities present. The molybdenum did not react with these impurities and had no effect on strengthening due to strain aging. Commercial-purity vanadium alloys containing more than 2 percent molybdenum were brittle at 77° K.

Jan 1, 1969

By E. Chin

The countries of Asia and the Pacific, with their large mineral resource base, are significant suppliers of a wide variety of minerals to both regional and world markets. Australia, China, and India dominate the commercial mineral exploitation in the region. Australia has known reserves of major minerals, which are adequate for both domestic demand, and for exports, and is a significant producer of bauxite; copper; diamond; gold; iron ore; lead; manganese; mineral sands (titaniferrous minerals, monazite, and zircon); nickel; salt; silver; tin; uranium; and zinc. China is the world leader in proven reserves of antimony, barite, ilmenite (titanium), magnesite (magnesium), molybdenum, rare earths, and tungsten. China also has large resources of low-grade iron ore and significant resources of other mineral commodities, such as coal, based on its production and export capabilities. India has significant resources of bauxite, barite, graphite, iron ore, and mineral sands.

Jan 1, 1995

In 2005, 14,666 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA).1 Almost half (48.5%) were sand and gravel mines, followed by stone mines (30.6%), coal mines (14.1%), nonmetal mines (5.0%), and metal mines (1.8%).

Jan 1, 2008

By L. E. Cardwell

This Bureau of Mines publication contains routine analyses and related source data for 495 natural gas samples from 21 States and three foreign countries. Of this total, 376 samples were collected during calendar year 1968. The remaining 119 analyses are of samples collected during previous years, but releases granting permission to publish the results Here not received until 1968. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917 and in late 1965 was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 576.4 Ten previous publications have presented results of 8,165 gas analyses made by the Bureau of Hines Helium Activity prior to 1968. The first three, Bulletins 486, 576,6 and 617,7 contain analyses and related source data on

Jan 1, 1970

By Clayton M. Rumsey

The U.S. Bureau of Mines investigated prospects and mineralized areas in and adjacent to the Indian Pass and Picacho Peak study areas in 1983 and 1984. The Indian Pass study area contains 33,640 acres and the Picacho Peak study area contains 5,450 acres. The study areas are located in the southeast corner of California and are underlain by Precambrian gneiss, Pre-Tertiary metavolcanic and metasedimentary rocks, and Tertiary volcanic and non-marine clastic rocks. Low-grade gold-silver resources may be present in hydrothermally altered gneiss in the upper plate and altered schist in the lower plate of the Chocolate Mountain thrust fault. The thrust fault is exposed in the study areas for about 3.5 miles west and 5 miles east of Indian Pass. Mineralized zones in the thrust plates were not discovered until 1983. Earlier prospecting explored areas containing minor copper carbonate occurrences in schist and sedimentary and volcanic rocks that are younger than the thrust. Twenty-three mines, prospects, and mineral occurrences inside the study areas and fourteen outs; de were examined for this study. These surficial copper occurrences have been prospected extensively in the study areas; large areas have been scraped, pitted, and trenched by bulldozers. However, they appear to be of limited economic significance. Slightly mineralized zones are in the northwest part of the Indian Pass study area where granite contacts sedimentary and volcanic rocks.

Jan 1, 1986

By Stephen D. Cramer

The Bureau of Mines conducted a study in which the magnetic fraction of urban refuse was used as melting stock in the preparation of high-strength, low-alloy and carbon steel. Product steels, made from incinerated steel can scrap, nonincinerated-nondetinned steel can scrap, nonincinerated-detinned steel can scrap, and dilutions of these scraps with No. 1 heavy melting scrap, were used in continuing tests in industrial, rural, and marine environments to determine the effect of residual elements and atmospheric pollutants on their atmospheric corrosion resistance. The respective commercial steels were exposed at the same time to establish baseline corrosion data for the test sites. Weight-loss data are reported for atmospheric exposures of 0.5, 1.0, 1.5, and 3.8 years. The marine environment was the most corrosive; the industrial environment was the least corrosive. The atmospheric corrosion resistance of the carbon steel was improved 25 pct by using incinerated scrap and nonin-cinerated-nondetinned scrap in the steelmaking process. In no case was the atmospheric corrosion resistance of carbon steel degraded by using the magnetic fraction of urban refuse as melting stock. The presence of sulfur in the corrosion film was the most important factor affecting the corrosion resistance of the steels. With increasing sulfur concentration, the rate of the corrosion reaction was reduced and the corrosion film became more protective. The residual elements in the product steels most responsible for improving corrosion resistance were copper and tin. These elements tended to increase the concentration of sulfur in the corrosion film. At the levels present in the product steels, Cr, Ni, and Pb had no observable effect on the corrosion resistance of the steels.

Jan 1, 1980

By Ralph Husack, J. W. Eckerd, G. A. Brady

The effect of gamma radiation on Pennsylvania anthracite and on reactions between anthracite and other materials was studied using a shielded , selfcontained 23,000 - curie cobalt 60 source . When anthracite was exposed to air at 65° C the reaction with oxygen was greater in the presence of radiation. than in its absence . Although drop- shatter tests indicated that exposure to radiation decreased the resistance to breakage of anthracite , this evidence of structural weakening was not supported by the results of grindability or particle- size studies . Irradiation caused definite changes in the gases evolved from evacuated samples of anthracite ; the percentages of hydrogen and carbon dioxide were increased, and the methane concentration remained unchanged . Carbon monoxide was evolved only from the unirradiated samples . Electron paramagnetic resonance (EPR ) measurements indicated large differences between evacuated samples and those exposed to air . There was little or no difference between irradiated and unirradiated samples , except that the free- radical content of unirradiated samples of anthracite increased progressively with higher temperatures of evacuation , but in the case of irradiated samples , no such behavior was found . Attempts to produce carbon disulfide and calcium carbide by reacting anthracite with sulfur up to 120 ° C , and with calcium oxide up to 400 ° C , were unsuccessful .

Jan 1, 1964

By Douglas F. Scott

This case study provides an example of how social marketing was applied to meet the needs of business customers. Federal regulations require that all companies develop a written program to track hazardous chemicals at their sites. The HazCom Writer, created by the National Institute for Occupational Safety and Health (NIOSH), is a software tool designed to help companies prepare their required Hazard Communications (HazCom) written plan and list all hazardous chemicals at the company's worksite. The social marketing goal was to provide a product for small- to medium-sized companies to use for federal HazCom rule compliance. The HazCom Wm'ter is a direct NIOSH response to customer and stakeholder needs (including the Mine Safety and Health Administration, the mining community, and Occupational Safety and Health Administration- regulated companies).

Jan 1, 2009

By Jr. Watts, J. L. Ambs, B. K. Cantrell, K. L. Rubow

"The University of Minnesota and the U.S. Bureau of Mines collaborated to develop and field test a personal diesel exhaust aerosol sampler (PDEAS). The PDEAS was field tested in five underground coal mines that use continuous miners and a variety of diesel vehicles, including diesel haulage and utility vehicles. One mine was surveyed a second time, with the haulage vehicles fitted with a low-temperature disposable diesel exhaust filter (DDEF). Aerosol samples were collected with a variety of instruments, including the PDEAS and the microorifice, uniform-deposit impactor (MOUDI). This paper presents the diesel exhaust aerosol (DEA) concentration data collected in these mines and assesses the impact of diesel face-haulage equipment, with and without exhaust filters, on underground mine air quality.The average DEA concentration at the haulageway location for five mines, determined by the PDEAS, was 0.89 mg/m3, with a standard deviation of 0.44 mg/m3 • DEA contributed 52 pct, of the respirable aerosol at the haulageway location. Use of the DDEF at one mine reduced DEA by 95 pct, with a standard deviation of 6 pct, and filter life averaged 10 h. DEA contributed a large proportion of the respirable aerosol concentrations in mines with diesel equipment, and a substantial reduction was achieved with use of a DDEF. INTRODUCTIONDiesel equipment is gaining popularity in underground coal mines. There are an estimated 1,951 units of diesel equipment in 152 underground coal mines compared with 1,100 units in 110 mines 5 years ago (J).5 This increased use is due to the recognition that diesel-powered vehicles are more versatile, which can contribute to increased productivity compared with their electrically powered counterparts. Approximately 33 pct of the diesel vehicles haul coal, 45 pct haul personnel and materials, and- 22 pct perform other duties, such as roof bolting, rock dusting, and road maintenance. Most mines using diesel equipment are located in Kentucky, Utah, Virginia, and Colorado."

Mar 1, 1992

By L. B. Pankratz

Thermodynamic data on the halides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H-H°298, -(G°-H°298)/T, ?Hf°, ?Gf°, and log Kf are given in tabular form. CP°, H-H°298, ?Hf°, and AGf° are also expressed algebraically.

Jan 1, 1984

By Jon K. Ahlness

The Bureau of Mines conducted laboratory and field experiments to determine tne amount of permeability reduction in uranium sandstone after its exposure to different drilling fluids. Seven polymer and two bentonite fluids were laboratory-tested in their clean condition, and six polymer fluids were tested with simulated drill cuttings added. Sandstone cores cut from samples collected at an open pit uranium mine were the test medium. The clean fluid that resulted in the least permeability reduction was an hydroxyethyl cellulose polymer fluid. The greatest permeability reduction of the clean polymers came from a shale-inhibiting synthetic polymer. Six polymer fluids were tested with simu-lated drill cuttings added to represent field use. The least permeability reduction was obtained from a multipolymer blend fluid. A field experiment was performed to compare how two polymer fluids affect formation permeability when used for drilling in situ uranium leaching wells. For this test, the polymer fluid with the best laboratory results (multipolymer blend) was compared with a commonly used polymer fluid (guar gum) that gave poorer laboratory results. When fluid injection rates for the four wells drilled with the guar gum were compared with those for the four drilled with the multipolymer blend, no statistically significant difference was found.

Jan 1, 1984

By Kenneth J. Miller

The Bureau of Mines two-stage coal-pyrite flotation process was modified to provide a more concentrated final clean coal slurry underflow which could be dewatered economically by filtration or centrifugation. This was accomplished by doing the first-stage coal flotation step in the conventional manner with a slurry of about 8 percent solids, but running the second-stage pyrite Flotation step with undiluted coal froth concentrate containing about 25 percent solids. The final clean coal underflow produced by the new technique contained between 26 and 30 percent solids; this pulp was sufficiently concentrated to be filtered industrially without further thickening. Sulfur removal was equal to that obtained using dilute second-stage pulp,

Jan 1, 1975

By Jeffrey A. Aldinger

This U.S. Bureau of Mines report presents an analysis of surface coal mining accidents involving mobile equipment for the years 1989 through 1991. Mobile equipment is defined as haulage trucks, front-end loaders, bulldozers, scrapers, and road graders. These five pieces of mining equipment accounted for 20 pct of all surface coal mine accidents and 41 pct of the fatalities. The general discussion of these accidents covers the accident causes, the primary activity of the accident victims, and other contributing factors. A more detailed analysis of accidents associated with each piece of mobile equipment is also provided. This report will provide mine managers and mine safety personnel with a better understanding of the hazards associated with mobile mining equipment. It identifies where improvements in mobile equipment safety can be made and those areas requiring additional safety emphasis, such as safety training, work procedure changes, or engineering changes to the equipment or work environment. The analysis was performed by a team of researchers using accident data and narratives provided by the Mine Safety and Health Administration.

Jan 1, 1995