Search Documents

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002

By Jürgen F. Brune, Alex C. Smith, William D. Monaghan

One of the predominant causes of fires in underground coal mines is flame cutting and welding. These fires can lead to major events such as the explosion that occurred on January 22, 2003 in an airshaft being constructed at the McElroy mine. Six contractors were inside the shaft at the time of the explosion and the explosion fatally injured three and seriously injured three [MSHA 2003]. Understanding the root causes of these fires and explosions will help prevent these types of events from occurring in the future. Fires and explosions require fuel, oxygen and an ignition source (heat). These three items are referred to as a fire triangle. The control of these three items in flame cutting and welding operations is required to prevent fires and or explosions. United States Department of Labor, Mine Safety and Health Administration (MSHA) Reports of Investigation (ROI), MSHA Mine Accident, Injury, and Illness Reports, and the MSHA Mining Industry Accident, Injuries Employment, and Production Data Base were analyzed and interviews and observations with mine workers and welders were conducted to determine the root causes of coal mine fires and explosions caused by flame cutting and welding operations. This paper will discuss the root causes and potential means to reduce the number of fires and resulting fatalities and injuries caused by or due to flame cutting and welding.

By R. G. Gürtunca

Over the past century coal miner safety and health has seen tremendous improvements, the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006 which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

By W. R. Hardwick

This Information Circular describes the development of block-caving methods and practices by the Miami Copper Co. at the Miami mine in Gila County, Arizona. It is one of a series published by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. This report gives a history of the district and outlines early prospecting and exploration including methods of sampling and estimation of ore tonnage and value at the Miami mine. Early mining methods are described, particularly those that influenced developments in the caving method. Mine exploration, development, and operating methods for block caving are described with particular attention to those factors, physical, economic, engineering, and managerial that have improved efficiency in the mining operations over a long productive period. Extraction, ventilation, wage system, safety, water supply, power plant, and shop facilities are discussed. The last section gives a brief summary of such costs as are available for publication.

Jan 1, 1965

By W. R. Hardwick

This Information Circular describes the development of block-caving methods and practices by the Miami Copper Co. ar the Miami mine in Gila County, Arizona. It is one of a series published by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. This report gives a history of the district and outlines early prospecting and exploration including methods of sampling and estimation of ore tonnage and value at the Miami mine. Early mining methods are described, particularly those that influenced developments in the caving method. Mine exploration, development, and operating methods for block caving are described with particular attention to those factors, physical, economic, engineering, and managerial that have improved efficiency in the mining operations over a long productive period. Extraction, ventilation, wage system, safety, water supply, power plant, and shop facilities are discussed. The last section gives a brief summary of such costs as are available for publication.

Jan 1, 1965

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke regardless of preparation. This report is one in a county series that describes the preparation characteristics of the coals of Mingo County, W. Va.

Jan 1, 1956

By B. M. Stewart

Researchers at the U.S. Bureau of Mines conducted a long-term groundwater monitoring and site characterization program at an abandoned 10-ha, acid-producing, copper-gold tailings impoundment in north-central Washington State. The purpose was to investigate contaminant release and transport, and attenuation mechanisms in the tailings, sediments below the tailings, and gravels downgradient of the impoundment. This report summarizes the monitoring results and physical properties of the tailings, the sediments below the tailings, and the groundwater system associated with the tailings. Water samples from the vadose and saturated zones of the impoundment were analyzed for 15 constituents. Concentrations of the same constituents were determined in water samples up to 3 m beneath the impoundment and in the shallow colluvium and deep bedrock at 76, 335, and 550 m downgradient and 168 m upgradient. Constituent concentrations within the tailings are quite variable and are influenced by pH, depth of oxidation, grain-size differential (surface area), hydraulic gradient, groundwater mixing, and the presence of hardpan layers, carbonaceous material, and organic matter. Most of the metal constituents decreased to background or near-background concentrations in the farthest downgradient well.

Jan 1, 2010

By R. R. Lowery

The Bureau of Mines developed hypereutectic aluminum-silicon alloys which 11.7.d better mechanical properties than the unmodified hypereutectic alloy. A commercial aluminum-20 weight-percent silicon LIr alloy was selected as a ary base for improvement. The primary silicon. grains were reduced from ASTM 4-5 to ASTM 8.5 by the use of phosphorus and phosphorus compounds. The remaining eutectic matrix was refined by sodium metal additions of 0.2 weight-percent. Solid solution strengthening of the alpha aluminum was obtained by adding 2 percent copper and 0.5 percent magnesium. Also, 1 percent nickel was added to harden the alloy. Optimum thermal treatment consisted of a solution treatment for 10 hour:, at 480° C with hot water quench, followed by aging for 6 hours at 175° C. The final alloy exhibited a Rockwell B hardness of 75 ±2 in the heat-treated condition. The ultimate tensile strength was 39,5O0 psi with no recordable elongation. The coefficient of linear thermal expansion was 20.4 x 10-6 per °C in the temperature range 20° to 300° C. No wear resistance data were collected.

Jan 1, 1966

By Liming Yuan

A computational fluid dynamics (CFD) study was conducted to model effects of coal properties on the potential for spontaneous heating in longwall gob (mined out) areas. A two longwall panel district using a bleeder ventilation system was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the three dimensional CFD modeling. The spontaneous heating is modeled as the low temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory scale spontaneous combustion studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted for three different US coals and simulation results were compared with some available test results. The effects of coal surface area and heat of reaction on the spontaneous heating process were also examined.

Jan 1, 2008

By Charles E. McCarthy, MORTON T. PAWEL, E. A. GEE, FRANK S. RIORDAN

Large tonnages of the magnesium silicate mineral , olivine, are known to exist in the mountains of western North Carolina and in the Puget Sound region of Washington. The North Carolina deposits alone are reputed to contain at least 230 million tons of ore averaging 45 to 49 percent of magnesium oxide In both areas the mineral is readily accessible and can be mined by the simplest methods ; one of the largest of the Washington deposits is located at tidewater .

Sep 1, 1946

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By Mark S. Redfern, Kim M. Corneliusa, Christopher A. Hamrick, Sean Gallaghera

Coal miners often handle heavy electrical power cables, weighing up to 10 kg per meter. These cables are manually lifted and attached to the mine roof to prevent damage from mobile underground equipment. Data suggest that workers who commonly perform cable handling tasks experience a high rate of lost time back injuries. In this study, six male underground miners performed a total of 12 cable-hanging tasks in standing, stooping, and kneeling postures, during which kinematic and ground reaction force data were collected. Reductions in vertical work space were found to result in a linear increase in the peak moment experienced by the lumbarspine (p<0.05). In restricted postures, peak moments were not significantly different in stooping vs. kneeling postures (p>0.05). Average lumbopelvic flexion during the tasks was highest in stooping conditions, followed by standing and kneeling exertions (p<0.05). Implications of this data with respect to design of cable handling tasks are presented and discussed. Keywords: Biomechanics, posture, low back pain, restricted workspace, mining

By Gerrit V. R. Goodman

In This Chapter [Design and operation of machine-mounted scrubbers Dust control with scrubbers and blowing ventilation Dust control with scrubbers and exhaust ventilation Dust control with exhaust ventilation and no scrubber Dust control methods common to all continuous miner sections Dust control for roof bolters] This chapter explains how to control dust at continuous miner sections in coal mines where the main dust sources are continuous miners and roof bolters. In relation to dust, there are three categories of continuous miner faces depending on the type of ventilation and whether or not a machine-mounted dust scrubber is used. These are— 1. Mining machines with dust scrubbers used with blowing face ventilation 2. Mining machines with dust scrubbers used with exhaust face ventilation 3. Mining machines without scrubbers used with exhaust face ventilation The approach to dust control is somewhat different in all three of these. However, there are many dust control features (such as the need to provide adequate airflow) common to all continuous miner sections. For workers at roof bolter faces, there are two dust sources: 1. Dust from the continuous miner when it is upwind. 2. A malfunctioning dust collector on the bolter, which allows dust to escape DESIGN AND OPERATION OF MACHINE-MOUNTED SCRUBBERS [Almost all new continuous miners are equipped with scrubbers. When the dust is excessive, it is possible that the scrubber needs some maintenance.]

Jan 6, 2003

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics are presented for air in a 2 - inch pipe - type electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig using a negative discharge electrode . Results of this one - geometry study show that current - voltage relationships are a function of air pressure and temperature and indicate that precipitators can be used at any temperature through about 1,350 ° F over the full range of pressure . Corona starting voltage and sparkover voltage vary directly with pressure and inversely with temperature . At temperatures above 1,350 ° F use of precipitators may be limited to operations at pressures somewhat above atmospheric pressure . Theoretical derivations are presented that relate the effect of gas density on corona starting voltage and the effect of ion mobility on corona current . Deviation from the theory is noted at high current levels . Theoretical discussion is presented to explain the apparent electrical limitations for use of precipitators at high temperature , low gas density , and high corona currents , conditions at which calculated ionic velocities are extremely high . Experimental results are interpreted in terms of the theory presented . 1,500 ° F thermal ionization does not appear to be a critical factor .

Jan 1, 1963

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

By Thomas O. Glover

The mining industry of Cameroon continued to be dominated by crude petroleum. Crude petroleum production has become the most important facet of Cameroon&apos;s economic development. Oil production was estimated to be 6.3 million tons in 1983 compared with 5.2 million tons in 1982 and 4.3 million tons in 1981. Over two-thirds of its export income was attributed to crude oil. The country&apos;s only refinery, dedicated in 1981, has a production capacity of 2 million tons. Cameroon has become self- sufficient in petroleum products since commissioning the refinery. The oil sector contributed approximately 13.5% to Cameroon&apos;s gross domestic product in 1982-83. Oil production was expected to rise from 125,000 barrels per day in 1983 to 156,000 barrels per day in 1985 when output peaks. Cameroon&apos;s ultimate recoverable reserves have been calculated at 100 million tons, or 750 million barrels of oil.

Jan 1, 1985

By R. D. Currie

Haulage accidents in the anthracite region cause fewer fatal and lost-time accidents per million man-hours than similar accidents in bituminous mines, a fact that may be accounted for in several ways, but primarily because haulage, in a large part of the region, is restricted to haulage crews operating only on the gangways where most of the miners seldom come in contact with movement or handling of cars and locomotives. Generally in underground mines the number of men injured compared with the number killed is greater for haulage than for roof-fall accidents, while the number of men killed by haulage is second only to the number killed by roof falls.

Jan 1, 1939

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By Gerald T. Homce

Data from the U.S. Bureau of Labor Statistics show that 89 water well drillers died on the job between 1992 and 2002, and 28 of these deaths were electrocutions (Figure 1). In fact, elec­trical accidents are the leading on-the-job killer of water well drillers. The use of electricity is such an integral part of our lives that we usually take it for granted, but if we don?t understand or choose to ignore the hazards associated with electricity, the results can be deadly. Why is electrical shock so dangerous? If the voltage (of a shock) is sufficient to drive electrical current through your body, just 10 milliamps of cur­rent (1000 milliamps = 1 amp) can cause muscles to contract and prevent you from releasing an energized wire or tool in your grip. As little as 30 milliamps of current can paralyze your breathing, and 75 milli­amps can cause your heart to stop pumping blood (ventricular fibrillation). As a comparison, a small bedroom night-light draws about 30 to 60 milliamps. Other factors influence how severely you?ll be shocked if you touch a live electrical circuit, such as the path electrical current takes through your body and how long it flows, as well as your body weight. How much voltage is needed to drive electrical cur­rent through your body? Not much! Generally, any power source at 50 volts AC or higher is considered dangerous.

Jan 1, 2008

By Peter Swanson

One of the primary methods for analyzing roof stability in underground mines is the age-old method of “roof sounding” where a miner taps on the roof and listens for the hollow sound of loose blocks of rock. This paper looks at the feasibility of using noncontact laser-based vibration measurements to detect roof fall hazards with the ultimate vision of improving, expanding and automating procedures for mine roof inspection. Vibration measurements made on loose blocks of rock in underground mines are summarized and compared to estimates of fundamental resonance frequencies for rock slabs of the size responsible for highly hazardous “skin failures.” Both laser Doppler vibrometry and full-field interferometric methods are examined and are considered to be feasible methods for detecting anomalous vibrations in loose roof rocks. Results from simple laboratory experiments using laser vibrometry demonstrate some of the proposed application concepts. While considered a challenge to move these techniques from the laboratory to heavy industrial or outdoor environments, the potential for success in the current application is enhanced by the reduced requirements of qualitative analyses.