Search Documents

By Larry Joe Linley

The Department of the Interior, Bureau of Mines is reviewing explosion protection methods for use in gassy coal mines. This performance criteria guideline is an evaluation of three explosion protection methods of machines electrically powered with voltages up to 15 000 volts AC. A sufficient amount of basic research has been accomplished to verify that the explosion-proof and pressurized enclosure methods can provide adequate explosion protection with the present state of the art up to 15 000 volts AC. The routine application of the potted enclosure as a stand alone protection method requires further investigation or development in order to clarify performance criteria and verification-certification requirements. An extensive literature search, a series of high voltage tests, and a design evaluation of the three explosion protection methods performed at White Sands Test Facility indicates that the explosion-proof, pressurized, and potted enclosures can all be used to enclose up to 15 000 volts AC, if the performance criteria and verification-certification requirements recommended in this guideline are implemented.

Jan 1, 1982

By D. Ng

A facility to evaluate the fire endurance of mine stoppings was constructed by the Bureau of Mines in the multiple entry section of the Bruceton (PA) Experimental Mine. Stoppings up to 6 by 18 ft can be tested in a manner simulating mine conditions. The stopping is subjected to a 70-min liquid fuel tray fire with an energy output of 75,000 Btu/min. The stopping and adjacent areas are instrumented with thermocouples and heat flux gauges. Data acquisition is by an automatic data logger capable of continuously recording over 100 channels of information. Two 8-in-thick concrete block stoppings and a galvanized steel stopping were tested. A crack developed on the fire side surface of the block stoppings where the flames were most intense. However, the temperatures of the unexposed surfaces of the stoppings never exceeded 800 C and the surfaces were undamaged. The steel stopping retained its structural integrity during the test. The temperature of the unexposed steel surface reached 5000 C, but combustible materials located 1 ft from the surface did not ignite. A 3/4-in-thick coating of construction plaster was applied to the fire side of the previously tested uncoated steel stopping. The quantity of heat energy transmitted across this coated metal stopping was reduced approximately 50%. All stoppings prevented the passage of flame and smoke.

Jan 1, 1988

By C. W. Davie

"This paper is the second of a series of progress reports4 on a study of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States.There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value.One of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although several manganese minerals were readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.5 Recent experiments have shown that a roast at 650 to 9000 C. converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution.6 Introduction of smelter gases containing much as 5 per cent SO2 during such a roast would not add much to the cost of the operation, and might result in the formation of considerable water-soluble manganese sulpate.Another case involves a subsequent step in the hydrometallurgical process, namely, the formation of oxides of manganese with simultaneous evolution of SO2 by the heating of the MnSO4 produced by evaporating its solution.A third has to do with the roasting of zinc sulphide ores containing manganese as a preliminary to leaching. During purification of the solutions to be used for the electrolytic deposition of zinc the iron must be oxidized to make possible its removal. Manganese dioxide has been used for this purpose,7 and since manganese compounds are present in some zinc concentrates,8 it is of interest to learn what happens to the manganese in a zinc sulphide or on roasting, and what portion of the manganese in the roasted product might be available for oxidation."

Oct 1, 1930

By Frederick H. Raab

The electromagnetic retransmission system is a new, automated method of locating trapped mine workers. This technique overcomes many 1 imitations inherent in electromagnetic direction finding by reducing the effects of the conducting ground to an acceptable maximum, by finding position accurately in the presence of antenna tilt, and by eliminating the need for the receiver to be located directly above the subsurface transmitter. Three transportable three-axis magnetic-dipole transmitters on the surface create a system of electronic grids in which the phases of the downlink Signals convey position information. The subsurface retransmitter modulates the uplink carrier of the existing beacon transmitter with the received downlink signal; the coal-pillar loop antenna is used for both receiving and transmitting. The uplink receiver uses a three-axis antenna and extensive digital signal processing. A small computer integrates data, estimates position, and controls system operation through VHF-FM communications. Both coal-mine and deep-mine operation are possible by selecting appropriate transmitting power and signal frequencies. This report shows such systems to be both feasible and practical.

Jan 1, 1980

By S. R. Zimmerley

[In the course of a flotation investi£ation, a siliceous gold ore was ground in a'ball mill to ':1inns 300-meeh. It wa. found that the small amotIDt of _Ius 300-mesh material had a gole.. assay approximately twice that of the oriGinal ore, &~d that this overs.ize nroduct also contained much abrac..ed iron. .,Joreove I the gold assay of the abraded iron t which was !1epnrated ma§metically', ~iVFl.£ eight ti;nes that of the are. These facts suggested that some r31aticnship ex?...,ted between the abnorma11y high gold content an the prese:1ce of brA-cit)" iron. It was decided, therefore, to investigate furt~er th~ Fl.Gsociation of the bold ~ith the iron abraded from the balls during sri~Qing ]

Jan 1, 1937

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolanda No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a posy-tine identification of the bed at Yolande No. o will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 18° As fax as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in. this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its' use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining CO.'s Granite Mountain shaft. How this, insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the fire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest producer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

By Edward L. McHugh

The study area, which comprises 28,443 acres within the Jacumba Wilderness Study Area, is in the California Desert Conservation Area, and along the U.S.-Mexico border 25 miles west of Fl Centro, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of mining claims, known mineral occurrences, and mineralized zones during the fall of 1983. Limestone resources were identified inside the study area; tungsten resources may he present. Metasedimentary rocks intruded by Cretaceous Quartz diorite predominate in the study area. Tungsten and some gold have been found in skarn zones along intrusive contacts; limestone deposits are in the pre-Cretaceous rocks. Tertiary and Quaternary volcanic flows, pyroclastic rocks, clay beds, and diatomite in lake deposits nave been investigated for possible non-metallic resources. Evidence of mining or prospecting was found at 26 sites in or just outside the study area. In 1983, 106 claims were held in 13 claim groups. One claimant was sporadically prospecting for gold on claims in the north part of the study area in 1983, and gravel was being mined from alluvium 1/4 mile to the east.

Jan 1, 1985

By Stephen R. Iverson

The U.S. Bureau of Mines made an economic appraisal of the Buttermilk study area, Inyo County, California in October 1980. Results of surveys indicate no potential for metallic, non-metallic, or energy resources in the area. However, glacial till covering most of the area prevented bedrock examinations by the appraisal teams or earlier prospectors. No mining claims are known to be in the area. INTRODUCTION Present Studies The U.S. Bureau of Mines, Western Field Operations Center, searched county mining claim records and other data available concerning mineral deposits, claims, leases, production, and mining activity in the area. The Bureau conducted field work in October 1980 searching for prospects and claim locations. Fourteen reconnaissance lode and placer samples taken from the area were analyzed for gold, silver, and tungsten; a spectrographic analysis also was run on selected samples.

Jan 1, 1981

By E. D. Calvert

This Bureau of Mines report discusses the electric-arc reduction of zirconium and hafnium oxides with carbon yielding a metal-metallic carbide mixture. The carbon to oxide ratio in the feed determines the metal to carbide ratio in the product. A sample of this product was produced -or testing as a feed for the deBoer iodide-dissociation process. A new technique for producing pure carbides is described, which uses the intense heat of the arc to volatilize the carbide. The condensed vapor form , crystals of nearly stoichiometric carbide, INTRODUCTION This research examines the preparation of refractory metal carbides in the controlled atmosphere electric-arc furnace.

Jan 1, 1962

By B. J. Moore

This publication contains analyses and related source data for 675 natural gas samples from wells and pipelines in 24 States and 5 foreign countries. The samples obtained and analyzed during calendar year 1980 are included in tables 1-4. Those samples included in tables 5-7 were collected during the years 1960 through 1979. However, permission to publish the analyses of those samples was not given until the past year when the operators were again contacted to seek release of the information. All of these samples were collected as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576. The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-two previous publications have presented the results of 12,152 gas analyses made prior to 1980. The first three, Bulletins 486,' 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1980. The other

Jan 1, 1981

By Laurence G. Britton

Accurate flammability and ignitability data for chemicals form the cornerstone of procedures used to assess the hazards associated with commercial chemical production and use. Since 1967 the ASTM E27 Committee on the Hazard Potential of Chemicals has issued numerous, widely used consensus standards dealing with diverse testing and predictive procedures used to obtain relevant chemical hazard properties. The decision to issue a standard rests solely with the membership, which consists of representatives from industry, testing laboratories, consulting firms, government, academia, and instrument suppliers. Consequently, the procedures are automatically relevant, timely, and widely applicable. The purpose of this paper is to highlight some of the widely used standards, complemented with hypothetical but relevant examples describing the testing strategy, interpretation, and application of the results. A further goal of this paper is to encourage participation in the consensus standards development process. The paper is published in two parts. The first part (in the preceding issue of Process Safety Progress) dealt with the E27 standards pertaining to thermodynamics, thermal stability, and chemical compatibility. The second part, published here, focuses on the flammability, ignitability, and explosibility of fuel and air mixtures. © 2005 American Institute of Chemical Engineers Process Saf Prog 24: 12?28, 2005

Jan 1, 2005

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

By Ernest W. Johnson, F. E. Cash

"INTRODUCTION Mine operators have long realized the importance of providing a satisfactory and dependable means of giving prompt warning to underground mine workers at the occurrence of a mine fire or other threatened disaster.Most underground mines of the Lake Superior district are prepared to inject a stench liquid into the compressed-air system quickly to give such warning. The liquid evaporates quickly and gives off an intense and easily recognizable odor even when present in minute quantities in the mine air. Workers in the mines studied have been fairly generally familiarized with the odor and instructed as to evacuation procedure when the warning odor is detected.In some mines provided throughout with electric lighting, including working faces, a prearranged light-flashing signal is given as a warning supplementary to that received from the stench.In a few mines, workers have been instructed to evacuate the mine immediately in the event the compressed-air supply is cut off, regardless of whether mechanical failure may be involved.Information obtained in observing a number of stench-injection tests is compiled and presented in the hope-that it will serve as an incentive to provide means of making stench injections at mines not now so equipped and for making similar tests at other underground mines, so that in case unsatisfactory results are obtained rectifying adjustments or changes may be made in time. It is further hoped that this paper will bring out the real importance of repeating these tests from time to time, at least once a year on each operating shift, so that in the event of an actual emergency, underground employees will receive a prompt warning."

Nov 1, 1945

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing and grinding methods, and costs, at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The, cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Evans Pipe Co., Uhrichsville, Tuscarawas County, Ohio. The author wishes to acknowledge the assistance of the following company officials: T. J. Evans, II, president; T. J. Evans III, vice president and general manager; and L. P. Young, general superintendent.

Jan 1, 1936

By Staff

This U.S. Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles.

Jan 1, 1989