Search Documents

By Doyle A. Ellerbruch

An FM-CW microwave system was investigated for measuring coal layer thickness. Measurements were made in three different mines near Pittsburgh, Pennsylvania, near Fairview, West Virginia, and near Coffeen, Illinois. Microwave frequencies in the range 1-2 GHz were used to measure samples up to 55 cm thick. All samples were backed with a naturally occurring shale. Measurements were also made on coal and shale samples compounded in the laboratory at the Bureau of Mines Pittsburgh Mining and Safety Research Center near Bruceton, Pennsylvania. The results indicate that layer thickness can be determined in most cases, although large anomalies may, in some cases, produce misleading results. Many anomalies that were detected with the FM-CW system were verified visually by drilling into the coal layer. The dielectric constant of coal apparently varies significantly within a coal seam. The form of the output signals from the FM-CW system seem to simplify the data interpretation and analysis process as compared to the manually swept microwave system used previously. It appears that this technique has the potential of measuring changes in the dielectric constant of a coal seam and providing an output that can be used for real-time corrections in layer thickness; measurement.

Jan 1, 1976

By F. G. Horino

This report presents the theory and design of a stiff loading machine used by the Bureau of Mines. The machine incorporates three high-strength steel columns as the restraining member in parallel with the specimen. The theory presented gives the basis of design and the dimensions of component parts of the machine. Laboratory verification of the theoretical stiffness is described using three different setups involving a hydraulic jack and spacers and confirms the stiffness calculations to within 1 percent. Experimental techniques, testing procedures, and special equipment designed for determining the complete stress-strain behavior of NX cores of both hard and soft rock are described. Typical test data are presented as force-displacement curves for two rock types, a marble and a granite.

Jan 1, 1972

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facilitate research on the fundamentals of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, but Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing adit has an advantage over an active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin in September 1936, with a crew of four laborers under a resident engineer. The laborers were recruited from nearby farms, and although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

By Robert I. Fujimoto

The work described was conducted to develop standards for the application of wire rope clips on wire rope. These standards include optimum number of clips and clip nut torques for wire rope sizes 1/4 through 2-1/4 inches, when used for forming an eye attachment in wire rope. Wire rope test specimens with clip attachments were load tested on tensile testing machines to determine an effective combination of clip nut torques and number of clips for each size of wire rope to develop efficiencies above 90 percent of the catalog ultimate rope strength.

Jan 1, 1973

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By F. E. Diebold

The wastewater-treatment system of the Anaconda Mining Co., at its Butte, MT., operation has been physically and chemically characterize modeled on a computer and investigated with respect to alternate systems for economic heavy metal recovery. The system involves lime addition to a mixture of acid underground copper sulfide mine water, acid effluent water from the iron induced precipitation of copper from acid leach solution and basic suspensions of solid effluent from a concentrator plant. Experimental chemical analysis and predictive computer calculations shows that the monosulfllte and disulfllte complexes of transition metals (Iron II being dominant) and alkaline earths are 40% of the total dissolved metal load of both acid streams. The suspended solids (30% by weight) in the basic concentrator slurries are dominated by quartz and pyrite and also contain kaolinite muscovite, biotite and undissolved lime. The mixture of these three streams result's in major reductions in concentrations of Al, Cu, Fe, Mg, Mn, Sir and Zn, and a pH >7 with calcium, sodium, potassium, and sulfate being the major dissolved ions. The treatment system has been simulated in the laboratory and accurately modeled on a computer. The computer program, an altered REDEQL-EPAK, is capable of accurately predicting the amount of lime required to reach a desired effluent water. Preliminary research has indicated the usefulness of electroprecipitation as a means of recovering the valuable metal load and providing an EPA acceptable effluent.

Jan 1, 1982

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By Russell G. Warncke

"This report is based primarily on a study of safety conditions and practices followed in the coal mines of Japan. Not all of the coal fields in Japan were studied, but typical mines in the largest producing areas and a fair cross section of coal-mine-safety conditions observed during February to April 1948 are described.Information was obtained through investigations conducted in the mines, discussions with mine-management officials and representatives of labor unions of the various mines visited, and examination of records and statistics from the various offices of the Coal Board of the Ministry of Commerce and Industry and from the Coal Association of Japan. Statistical data covering the same subject, obtained from different sources, varied in many respects and apparently were reported inaccurately, but such discrepancies can be attributed to different methods of reporting and compiling statistics.It is difficult to correlate the high fatal and nonfatal injury rates that prevail in Japanese coal mines with the conditions observed in the mines. Virtually all mines visited were attempting to prevent accidents and explosions, by apparently following known safety precautions for the prevention thereof. Some commendable safety innovations were observed at several mines; they indicated that mine officials are giving thought and consideration to hazardous conditions that affect their particular mines.Naturally, the operating officials and management were anxious to impress the writer with their interest in accident prevention and safety. Operating officials were found to be receptive to safety and wore interested in formulating definite safety programs. Some nines had well-planned and well-organized safety programs, which, if put into effect, would contribute greatly toward reduction of accidents.The approach to safety in Japan is quite different from that in the United States, especially the concept of personal responsibility for accidents and the extent to which the individual should be protected against hazards. Management is responsible for providing and maintaining safe working conditions. Collaboration between management and worker, as understood in the United States, does not exist in Japan.Increase in accidents since the cessation of hostilities is the result of unsettled economic conditions in the coal industry, influx of inexperience workers, and breakdown of discipline among the miners, who have been organized into unions. Those unions are greatly influenced by ""leftist"" tendencies.It was observed that the Japanese mine worker is fatalistic by nature and has little, if any, noticable safety consciousness. The most urgent major requirements to reduce accidents in the coal mines are to train the worker in accident prevention and instruct him regarding the inherent hazards of his occupation.Revision of the mining laws would help to reduce accidents if the companies would comply with such laws and provide safer working places and if the workers would cooperate with management and observe and comply with such laws as are enacted for their protection."

Dec 1, 1949

By R. E. Brewer

A critical review of the numerous test methods that have been devised for measuring the "plastic" and "swelling" properties of bituminous coking coals and the practical evaluation of the data obtained has long been needed. The author appreciates fully, first, the arduous problem of doing justice to the merits and limitations of the many original test methods and their manifold modifications and, second, the more difficult task of interpreting the test data obtained in their practical applications to the important problems involved in the coking process. It has been the constant aim of the author to point out the broader significance of the test principles employed in the different classes of test methods and the usefulness of the test data obtained in relation to the problem of coking bituminous coals, rather than to stimulate unduly a controversial criticism of the merits and limitations of any particular class of test methods or of individual test methods devised by different workers. The task has been quite difficult because of the almost total lack of accepted test standards and specifications.

Jan 1, 1942

By D. E. Shanks

This U.S. Bureau of Mines (USBM) research simplified an earlier hydrogen chloride (HCI) leach-sparge process developed by the USBM to recover reduction-grade alumina from domestic kaolin clay. Improvements were made by decreasing the initial leaching acid concentration from 25 to 20 pet, decreasing the leaching time from 1 to 2 h to 15 to 30 min, eliminating the solvent extraction step for Fe removal, and eliminating the step to recover the AI content of the bleedstream circuit. A 10-cycle bench-scale experiment of the simplified process showed that the ferric chloride (FeC13) concentration built up to 9.3 g/L in the recycle stream. This did not interfere with any of the unit operations or final alumina product purity because Fe forms stable soluble chloride complexes when sparged with HCI and is easily washed from the large aluminum chloride hexahydrate (ACH) crystals. The reduced leaching time and acid concentration did not decrease Al extraction.

Jan 1, 2010

By P. S. Haury

"INTRODUCTION Many ore deposits were discovered in the Wallapai Mining District, which covers the Cerbat Range in Mohave County, Ariz., during the early period of mining there from about 1865 to the 1890's. A considerable amount of production was obtained from shallow lead carbonate ores that carried considerable gold and silver.Mining was revived in 1906 and again during the First World War, and soma of the mines were deepened into the underlying sulfide zone. Substantial quantities of metal were recovered from two mines, the Golconda and the Tennessee-Schuylkill, that were, developed to depths of 1,600 and 1,400 feet, respectively. The Golconda is credited with $6,500,000 gross productions. 2/ This mine was not operated after 1917. The Tennessee-Schuylkill is still operating after a yield of about 300,000 tons of ore that averaged 4.33 percent lead and 7.74 percent zinc and contained an appreciable amount of gold and silver.Many of the old mines were reopened in 1942 or 1943 under the stimulus of premium prices for lead and zinc. A large proportion of this work was finished with loans from the Reconstruction Finance Corporation. It was believed that a good deal of lead and zinc could be recovered from the mines if a custom mill for concentration of the ores was available locally."

Aug 1, 1947

By John F. Wiggert

The first signal system used in the Homestake mine between the cagemen and hoisting engineers was a mechanical one. It consisted of small cables or jointed steel rods hung in the cage compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers' positions by means of bell cranks and steel wires. At the various stations the bell lines were also fitted with bell cranks and connected levers, so that the cagemen could operate the bells from the stations when they were handling rock or other material and not riding on the cages. Such a system was inherited from the days before extensive electrical development. It served quite well for shallow shafts, but for depths of a thousand feet or more it was very slow and cumbersome. It required consider-able muscular effort to operate it quickly, because of the inertis of its great weight and also because of frictional resistance. The maintenance cost was quite high because of the many wearing parts.

Jan 1, 1937

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat area of northeastern Colorado. Sample 31310 was taken from the Continental Oil Co.'s well Briggs No. 1 which care in or September 27, 1931, with a maximum production of 940 barrels per day. Sample 31311 was taken from tie Reiter-Foster Oil Co. Is well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day.

Jan 1, 1932

By M. O. Serbousek

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed an eight-piece precast reinforced concrete drift set for a small opening. Twenty-two sets of three different member sizes were tested to destruction under two loading conditions. A discussion of the test results and typical failure patterns is presented.

Jan 1, 1969

By R. A. Vik

The influence of thermal treatments on the grindability of low-grade hematitic iron ores from Michigan and Minnesota was examined in bench-scale tests. Treatment factors were roasting temperature, roasting atmosphere, and ore cooling conditions. Bond ball mill grindability and work indices were used as response indicators in evaluating the condition of the ore. Of the three treatment factors evaluated, roasting atmosphere, which brought about the con version of iron oxides to magnetite, had the most significant effect; roasting temperature had the next most important effect; and cooling condition had the least effect. Optimum grindability was obtained with reduced-quenched products of both ores at 650° C, near the alpha-beta phase transformation of quartz.

Jan 1, 1971

By E. Morrice

As part of its efforts to maximize process efficiency and decrease energy requirements in mineral processes, the Federal Bureau of Mines has investigated methods for beneficiating bastnäsite ores from Mountain Pass, Calif. The results of a bench-scale study on the flotation of bastnäsite ore are presented. Flotation at a pulp temperature of 40° to 45°C yielded a cleaner concentrate containing 58.7 pct RE203 at a rare-earth recovery of 67 pct. These results are comparable to those reported for the commercial beneficiation method in which the pulp is heated to boiling before flotation. An attempt was also made to recover a barite flotation concentrate from the bastnäsite rougher tailing. Concentrates containing only 70 pct barite were obtained.

Jan 1, 1982

By J. M. Kurtz

Ten Methane Monitoring Systems and Machine Control Circuits were examined and tested per the requirements in CFR Title 30, Parts 18 and 27, the Standard UL 913 and the document "Test Requirements For Instruments or Apparatus to be Considered for M.E.S.A. Intrinsically Safe Certification (Tentative)". The test results indicate that none of the products complied with all parts of all requirements as interpreted by Underwriters Laboratories Inc.

Jan 1, 1980