Search Documents

By William H. Snyer, Hank Cox

A high explosive device using Linear Shaped Charge (LSC) (to rapidly cut vent and drain openings in a rail tank car) is described. In the event of damage to a tank car loaded with a pressurized flammable fluid, it may sometimes be necessary to perform controlled on-site vent, drain and burn operations. Existing techniques required refinement to achieve the desired safety and procedural reliability for use in emergency situations.

Jan 1, 1994

By J. P. Proulx, Richard O’Meara, Ruilin Yang

A blast optimization project was carried out at an Open Pit Metal Mine using the Multiple Blasthole Fragmentation (MBF) Model and the Multiple Seed Waveform (MSW) blast vibration model. The aim of the project was to optimize rock fragmentation of the ore blasts to significantly increase metal recoveries while keeping the blast vibration levels at the highwall under control. The project also examined the blasts in the waste rock using the Fragmentation model to expand the blast pattern and select economical explosives for drill and blast cost savings while minimizing any adverse effect on the dig rates. Two sets of near field signature blasthole tests were conducted in both hard ore and relatively soft waste rock. The information from the near-field signature blasthole vibration was used as input to both the MBF and MSW models, as site specific geological information interacting with blasting. The implementation of the full blast design is also input to the MBF and MSW models. A production blast for each rock type was monitored for blast vibration and rock fragmentation. The full blast information and the blast results are used to calibrate and validate the models. The Fragmentation and Vibration model were established for the two rock types at the mine. At each site the Fragmentation modeling was conducted in parallel to the Vibration modeling to ensure blast vibrations were under control while the rock fragmentation was improved. The Fragmentation MBF and MSW are each an integral part of the blast optimization tool. Various scenarios using different explosives, hole delays and blast patterns were modeled for rock fragmentation and blast vibration. The recommendations from the modeling project were to be field trialed at the mine. The implementation of the recommendations was expected to help the mine significantly in terms of the mining economics, and high wall stability and safety.

By Stafan Rose, Art Madsen

Four years ago, Peabody’s North Antelope Rochelle Mine (NARM) site started experimenting withANFO and Liners in its Cast Blasting operations. The motivation to use ANFO was based on the following:1. ANFO generates more gas thereby resulting in greater heave/movement. 2. ANFO is a more consistent product because there are less components/ingredients. 3. ANFO when protected from water contamination does not produce NOx smoke.

Jan 1, 2007

By Ray Jambakhsh, John Okell, Frank Cook

"In early 1988, an experimental study was carried out at the Inco's McCreedy West Mine inLevack, Ontario. The objective was to develop blasting techniques which would allow themine to maintain production targets and reduce blast induced vibrations and overpressure.Due to its close proximity to the town of Levack (approximately 900 feet), particularconcern was expressed as to the vibration and overpressure resulting from the undergroundblasting operations."

Jan 1, 1993

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.

Jan 1, 2004

By R E. Langston, S M. Gazioglu

A preconstruction inventory program was conducted to determine the existing conditions of residential, non-residential and all other structures within 2,000 feet of the blasting limits for a highway excavation site in Asheville, North Carolina. Prior to major production blasting, eleven test blasts were detonated to establish site specific propagation parameters in order to develop contours of maximum allowable explosive charge weights per delay. The method of scaling distance by the square root of charge weight per delay was utilized in developing the contours of allowable charge weights. The charge weight contours were revised during blasting operations as additional vibration data became available. The effects of blast induced vibrations on a nearby water storage reservoir, a nearby vehicular tunnel and other adjacent residential and non-residential structures were observed and monitored over a period of two years of blasting operations.

Jan 1, 1980

By V Krishna Mohan, J Edmund Hay

This paper discusses the results of the gap sensitivity measurements made on water-gel explosives, sensitized by monomethylamine nitrate (MMAN) and flake aluminium, and one emulsion explosive. This study specifically deals with the effect of the mode of initiation, end or center, on the measured L50 values with air gap and coal dust gap for the above explosives. Similar measurements have also been carried out on a nitroglycerine (NG) - based explosive. The results show that the mode of initiation plays an important role in determining the air-gap sensitivity of these explosives. However, in tests carried out with the coal dust gap, the L50 ( grams of coal dust ) values for these explosives are close in both the types of initiation. The results indicate that the sensitivities of these explosives may be ordered in the following manner: NG-explosive>> Aluminized explosive ~ MMAN-explosive > Emulsion explosive

Jan 1, 1982

By Tuan Nguyen, Dirk Hummel, Ruilin Yang

In a tunnelling site in Japan, it was found that detonators failed to initiate with their shells and primary explosive intact. Their capacitors, however, were discharged due to some damage on the application-specific integrated circuits (ASICs). These detonators are distinctly different from other commonly observed failures, where the shells are rather crashed due to excessive dynamic pressure received from neighbouring blastholes which fired earlier. Such incident has not been reported elsewhere. Detonator failures during a blast are deemed not safe and can cause disruption on the project productivity. It is therefore desirable to understand the origin of such event. Various measurements were conducted to diagnose the problem, but the root cause had yet to be identified. This paper applies a discovery from a 60-year-prior-laboratory experiment and formulates a theory that could explain the observed detonator failure and predicts the measurements and observations.

Feb 6, 2023

By C. Morel, P. Fredes, L. Rojas

This article presents a comprehensive study on the development and application of the specific module called "Exclusion Zone" created by Orica to determine blast evacuation exclusion zones. This module, integrated into the "SHOTPlus™ (blast design software)" software, has been used in the context of optimizing equipment evacuation exclusion zones in a northern Chile mine. The main objective has been to reduce the travel times of extraction equipment without compromising the safety of individuals. The module considers various factors such as the explosive charges used, stemming, sector topography, and detonation sequence to determine the rock projection generated by the blast. Furthermore, it utilizes information collected by drones and support tools such as Groundprobe and BlastVision™. The results obtained demonstrate that the use of this technology has allowed the optimization of blast evacuation distances in the northern Chile mine, generating significant economic benefits for the client.

Jan 1, 2024

By César Ugaz Castañeda, Paulo Fernández Alvarado, Richard Sotomayor Oblitas, Rocke Enríquez

Mina El toro has been making substantial changes in its operation to improve its social impact and productivity. Because of the use of gasified emulsions and electronic initiation system, it was possible to mitigate vibrations and carry out massive blasting, increasing its production by 4.2% and minimizing complaints from communities.

Feb 1, 2020

By Callie Covert

This paper describes the application and results of a more efficient method of breaking boulders using dynamite and water. This method is being used for the disposal of boulders that result from pinnacle and cap rock remaining after blasting on highways and job sites. This method is a faster and less expensive use of dynamite to reduce oversized boulders than the conventional rock hammer. The problem with excessive fly rock has been substantially reduced when using this technique over traditional methods.

Jan 1, 2001

By AK Chakraborty, AK Raina

Burden of drill hole is third most sensitive parameter effecting the ground vibration in blasting apart from maximum charge per delay and distance. Various types of burdens can be seen in practical bench blasting situations. Burden can be expressed as drilled burden and initiation burden. Drill holes may have various front row burdens (toe burden), which may be different from the designed burden. In order to ascertain the impact of front row burden as well as the initiation burden on intensity of ground vibration and air overpressure experiments were conducted in sandstone overburden benches of an opencast coal mine and limestone quarry. Blast trials were carried out in cognisance of both drill and initiation burden while keeping all other parameters constant. Effect of front row burden was also extensively studied by keeping almost all other parameters constant. The results of the study reveal that there is substantial influence of front row burden on the vibration and air overpressure. The statistical analysis of vibration and air overpressure data with drilled burden and initiation burden gives significant evidence that the level of peak particle velocity of vibration (Vmax)) is reduced by reducing effective burden with modification of initiation. Data analysis carried out for air overpressure versus initiation burden shows that reducing effective burden with modification of initiation results in increasing the level of P. The study reveals a qualitative assessment of the influence of burden on the blast induced vibration and air overpressure. The study also recommends to modify the initiation pattern to reduce the effective burden in order to reduce the vibration, without disturbing the fragmentation.

Jan 1, 2004

By Ken Schei, Martin Reed, Samuel Bowser, John Wright

From October 18 through October 21, 2001, United States Antarctic Program blasters opened ten access holes for research divers in 11-ft. thick sea ice at Explorers Cove, McMurdo Sound, Antarctica. During this project, a blasting seismograph with a hydrophone accessory was used to monitor the underwater shock waves associated with the blasting technique. Shock wave values averaged 42.3 psi for initial (cratering) shots and 5.9 for subsequent clearing shots, indicating that the ice absorbs most of the shock wave. The results also provide data for refining safety protocols for divers and for the protection of marine biota.

Jan 1, 2003

By Anthony Konya, Calvin J. Konya

The publication, RI8507, from the U.S. Bureau of Mines established an envelope equation that related scaled-distance to peak particle velocity in an attempt to predict ground vibration in the design phase of a blast. This has been further modified by Oriard, Dupont, Konya & Konya, and others to develop more refined prediction models for specific situations to obtain better predictions. While these equations can be an ideal starting point for a greenfield blasting project or a project with no given information, these equations can have errors.

Jan 1, 2018

By P A. Lang, J G. Ayotte, R W. Humphries

Atomic Energy of Canada Limited (AECL) has the responsibility for research, and development of technologies, for the safe and permanent disposal of Canada's nuclear fuel wastes. As part of this comprehensive program, AECL is constructing an Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, to evaluate aspects of the concept of waste disposal deep in stable geological formations. No nuclear wastes will be used in the URL program.

Jan 1, 1986

By Corry Goumans

Description of Project: Drilling, Blasting and Installation of Catenary Cables. Project Owner: Rio Tinto Alcan

Jan 1, 2010

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984

By John Brulia

"Definition of On-Site Security: All mandatory and non-mandatory, deterrent and loss control measures undertaken by an authorized explosives business tokeep its stocks of explosive materials and precursors from: • (1) THEFT • (2) LOSS"

Jan 1, 2006

By Minoru Kawamora, Koichi Kurokawa, Kenji Hashimoto

We developed concentrated remote control blasting system to blasting simultaneously at a large number of sites in a mine of large scale. This system is consisted of three parts, the first part is a control station with high voltage power source units, the second part is a relay terminal with relaying and branching units, and the third part is a blasting machine with charging and discharging units. The control station is connected with the blasting machine by mean of control bus wire. The blasting machine adopts MBS(electromagnetic induction blasting system) for the reason of safety and good handling.

Jan 1, 1990