Search Documents

By D T. Froedge

In 1972 the Kentucky State Legislature enacted House Bill 625 which was known as the Kentucky Blasting Law. This law was enacted primarily to stop problems associated with surface mining, but when it was enacted all industries using explosives were included. The bill was assigned to the Department of Mines and Minerals which created a Division of Explosives and Blasting. At that time, this division only had regulations concerning blasting. One should make a distinction between blasting regulations and other explosive regulations. Blasting is the actual use of explosives, the control of the blasting operation, how much is used, at what distances to buildings, the yardage, and other actions associated with the detonating process, explosives regulations generally including safety to the personnel and the storage of explosives.

Jan 1, 1977

By P. D. Lightfoot, C. Badeen, R. Turcotte, D. E. C. Jones

Following localized (i.e. hot-spot) ignition, there is a minimum pressure required for combustion to propagate in water-based commercial explosives. The latter is usually referred to as the ‘Minimum Burning Pressure’ (MBP) of the explosive. In the present work, both an apparatus based on hot-wire ignition and an associated methodology were developed to measure the MBP of water-based explosives. It was demonstrated that the MBP constitutes a sharp pressure threshold below which the probability of inducing sustained burning in these explosives becomes very small. It was found that each emulsion explosive tested has a distinct MBP value, which depends critically on its formulation. It appears that this test may offer a firm basis for the classification of emulsion explosives for regulatory purposes.

Jan 1, 2004

In situ, most Taconite is heavily pre-fractured; because of the high cost of comminution of taconite, maximum fracture of pre-existing blocks is desirable. Sustained borehole pressure plays a significant role in fragmentation, especially by penetrating pre-existing fractures. The distribution of explosive-induced energy in the burden in three dimensions was calculated. Data on the comminution of single particles was used, with the distribution of energies and the distribution of pre-existing block sizes, to calculate fragmentation for a case study. The calculation agreed well with the measured fragmentation. Sequential comminution events are much more efficient than single ones, and enhanced fragmentation may be possible with alternative blasting practices. Some important factors in the dependence of comminution on energy input are discussed.

Jan 1, 1995

By Michael S. Wieland

The work-principle method was developed for theoretically resolving toxic fumes from non-ideal charge formulations. The whole description of a wanted process refers to macroscopic changes resulting from removing and imposing constraints that work one at a time to chronologically render trajectory terminal (key) states. The trajectory resolution utilizes a thermodynamic quasi-potential or negative work function, and numeric results require some appropriate standard thermodynamic (equilibrium) reaction code TDRC. The underlying method is unable to restrict reactions, tailor the work output or resolve states within the trajectory transitions, so the trajectory terminology is used somewhat figuratively. The work-principle model has the working fluid (reaction material) interacting with a tremendous reservoir (chamber air and walls), while forecasting the work performed upon a mechanical agent.

Jan 1, 1998

By Paulo Cesar Pavan

T&T or Traceability, is a concept of generating, storing and on demand providing information about all traceable items in the supply chain

Jan 1, 2019

By W. Reisz

Blast area security is the responsibility of everyone involved in the blasting operation and goes well beyond simply controlling access by unauthorized personnel.

Jan 1, 2009

By Ben Barrett

Dangerous goods, known as hazardous materials in the USA, are subject to special controls during transport to ensure the safety of the public. Dangerous goods are divided into nine classes, and Class 1 is devoted to explosives. Unlike storage or manufacturing, explosive transportation crosses the political boundaries of localities and nations, and its regulation must be centrally managed to avoid duplicate costs of complying with multiple regulations. Additionally, the transport of dangerous goods occurs by four different modes – highway, rail, vessel and air. While each mode has differences which must be addressed, the fundamental principles of classification, packaging, hazard communication and documentation remain the same. When a shipment travels by multiple modes and across borders, consistent regulations become paramount to cost efficiency. This is a common occurrence in the growing global economy.

Jan 1, 2010

By Michael E. Kovach

This discussion is an overview of an approach to drilling and blasting angle holes at Martin Marietta Aggregates. Method of determining burdens, hole depths, angle settings and explosive selection will be discussed in detail with an emphasis on safety and production. Such techniques and methods involve the use of hand-held surveying instruments such as the Abney level, pocket transit and inclinometer along with measuring tape and burden pole. An interesting method developed by Oscar Banfield a retired Martin Marietta and E. I. duPont engineer, for setting the proper angle on a drill will also be presented. This treatise is a discussion of the use of simple yet important tools and techniques a blaster should use to resolve both routine and complex problems encountered during quarry blasting operations.

Jan 1, 1992

By Edward J. Walter

A vibration record is a complex of motions resulting from a combination of direct, reflected and refracted seismic energy that originated at a blast source. Multiple hole blasting using delays further complicates the motion in that overlapping of seismic wave trains may occur when delays do not fire in the programed sequence. This can result in variations in amplitude, frequency and wave-1ength of the vibration. Amplitude may be doubled, frequency may oscillate between the highest and lowest frequencies present and wave-length may approach doubling of the longest wave-length present. These effects can present serious problems to conducting a safe blasting program since increased amplitudes and lower frequencies present higher damage potentials for structures. The development of these effects is described and illustrated graphically to show how these effects can occur.

Jan 1, 1989

By Douglas Lindsey, Glenn Hazen, Shad Sargand

"With the innovation of computational equipment, an exact analysis of structures as dynamic systems is more approachable. Accordingly, the dynamic system can be established, if the natural characteristics such as the natural frequency and the damping fraction of a system are known. Through dynamic analysis, the response of a structure can be predicted from ground vibration, and it becomes possible to forecast the damage potential to the structure with reasonable accuracy. Most vibration will appear as single harmonic or superposition of waves that consists of several harmonics with different frequencies. A vibration signal can be expressed, therefore, as the function of sine waves. If a signal is periodic, the particular harmonic with the smallest frequency will befundamental and frequency of the others will be multiples of the fundamental frequency."

Jan 1, 1993

By Dale Preece, Stephen Chung

Development of DMCBLAST-3D is continuing and now includes the capability to simulate the detonation of multiple blastholes in multiple rows that make up a conventional bench blast, either in a rock quarry or a surface coal mine. DMCBLAST-3D is a three-dimensional extension of the proven twodimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2002

By Sanjay Sengar, Nabiullah Pingua, Saurabh Sahay

In India, more than 80 percent of the total of 557 million metric ton coal production comes from open-cast mines involving large overburden removal with average 1:3.5 stripping ratio which is going to in-crease in future. This operation consumes nearly 0.5 million metric ton explosives consisting of 80-85 percent bulk explosives and remaining 15 to 20 percent non-permitted large diameter explosives. Quali-ties of bulk explosives play an important role in rock blasting. Post blast results like poor fragmentation, tight mucking, toe problems, improper muck profile and lower productivity of mine may require chang-es in explosive loading factor (amount of explosive used per unit of rock blasted ). The explosive load-ing factor is an extremely important index to assess the economy of blasting operation.

Jan 1, 2014

By W C. Burkle

A rather common observation over the last several decades at least has been that rock or ore properties influence blasting results more than does the explosive type that has been used in the blast. It we accept that premise than it is held here that the material to be blasted should receive even closer attention as to its properties. Several years ago, Dr. Richard Ash published papers that pointed out the rock properties that mostly influence blasting. These principles are given attention in this paper. We have gone somewhat further - or lets say expanded this subject in regard to the role of rock structure in open pit blasting. Though open pit work is given some prominence, we believe that much can be observed and applied to underground mining.

Jan 1, 1979

By Steven D. Sandbrook

A man by the name of Louis Binstock once said, “Too often the shortcut, the line of least resistance, is responsible for evanescent and unsatisfactory success.”

Jan 1, 2015

By Mark William Withey

Blasting safety in surface mining is a necessary industrial goal. Proper techniques and disciplines exercised during the blasting process enhance the probability of achieving that goal.

Jan 1, 1995

By Les W. Armstrong, Stephen B. Richardson, Neville T. Moxon

A study was carried out to determine how different degrees of stemming confinement, that is the retention of the explosives gases, effects fragmentation and movement during blasting.

Jan 1, 1993

By Richard Dooley

The purpose of this paper is to give a description of a controlled blasting program and why Georgia Power now has one; mainly because of the Spillway Project.

Jan 1, 1981

By Seokbin Lim

According to published literature, the equation of motion of linear shaped charges (LSCs) has been investigated as early as the 1960s in a few research organizations. However, due to the comparatively low penetration performance, the amount of research has not been extensive, and the use of this device is quite limited in very specialized applications. Traditionally, the equation of motion of an LSCs’ liner shares the same basis as conical shaped charges (CSCs) because they are under the same functional category and generally have similar geometric configuration. However, the nature of LSCs is not quite similar with that of CSCs due to multiple reasons, and they required a new set of equations to properly address their performance. In this paper, we reviewed different sets of approaches in describing the liner collapse behavior of LSCs mostly based on the author’s contributions.

Jan 1, 2014

By P D. Kasbanis, Lyall Workman

The energy output of an explosive is typically calculated using an equation of state and computer applications. Results are reported as weight and bulk strength, either in absolute terms or relative to ANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of "available energy" associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated.

Jan 1, 1996

By Geoff Baldwin, Alastair C. Torrance

The use of monitors to assess equipment performance is carried out on a routine basis in many industries. The benefits gained through process control in knowing exactly how the equipment is working far outweigh the initial capital costs of the monitor. In the mining industry several dragline monitors have been developed and installed on equipment through out the world, but to date none has been fully accepted by the industry. This paper describes the use of a sophisticated monitoring system which incorporates an onboard processor to assess both dragline and blast performance. The use of a radio telemetry link for data transfer has removed the need for manual data collection and transfer, leading to a more efficient and powerful system. Significant effort has been put into the development and verification of a dig index to allow blast performance to be objectively assessed.

Jan 1, 1990