Search Documents

By Paulo Castillo, Cesar Gomez, Jaime Alvarez

Operations using flotation to produce mineral concentrates require testing of frothers to characterize their ability to preserve bubble formation size and to build a stable froth. Many techniques have been proposed to measure parameters associated with these two roles. These techniques focus, in general, on only one of these roles and are based on special equipment operated at conditions quite different from those existing in industrial cells and columns. Both roles have been simultaneously characterized in a laboratory flotation column, but the requirements associated with the installation and operation of one of these units, are a serious limitation for its use on-site. A technique based on the use of a laboratory mechanical cell, a common piece of equipment in operations, will have wider application. Establishing the ability of a frother to control coalescence by preserving bubble formation size is done through bubble size measurements as a function of frother concentration. Froth build-up and stabilization is associated with the amount of water carried by bubbles into the froth layer, which has been demonstrated to correlate with the gas holdup in the collection zone. Procedures devised for determining the critical coalescence concentration (CCC) from measurements of bubble size as a function of frother concentration, and the gas holdup by collection of water displaced from the cell by the presence of bubbles at different frother concentrations, were tested. Three analytical-grade frothers were utilized: a straight-chain (1-heptanol) and a branched (MIBC) alcohol and a polyglycol (PPG425). The results obtained at a standard set of conditions, demonstrated consistent differences between these frothers, and the ranking from least to most effective for reducing bubble size or decreasing water drainage followed the same sequences found when more complex frother characterization techniques are used.

Jan 1, 2014

By G. V. Kalabin

"The paper supports applicability of satellite imagery at regional and local level for rapid quantitative assessment of natural environment in zones of activity of mining complex enterprises. Exacerbation of environmental problems during mineral mining and processing associated with their scale and geography of field distribution through the vast territory of our country requires constant monitoring of natural environment status, which necessitates engagement of space surveillance nowadays. It is proposed to use the monitoring of land cover and land use at regional and local level for the environmental assessment of a particular production or complex productions. You must establish the dependence of NDVI change trend with the magnitude of anthropogenic impact on the source or multiple sources of environmental pollution a particular area.. We present the results of studies of vegetation remote sensing methods in a number of territories placing mining enterprises. INTRODUCTION Ensuring a healthy environment is necessary both in untouched areas and disturbed. The condition of the developed territories should be monitored with particular attention, since the restoration of the disturbed territories requires great efforts and financial costs. More narrowly, the health of the environment (Zakharov V.M. and etc.,2001) means its quality ensuring the health of man and other species of living organisms, which includes two aspects (Zakharov V.M. and etc, 2000): - ensuring an environment conducive to human health as a biological species: - maintaining the health of the natural environment, i.e. its constituent species of living organisms and plants. The consequence is the disturbance of natural ecosystems, which determines the quality of the environment, favorable for human habitation and the state of health of the population in total determine the status of the territories where enterprises for the development of georesources are located and allow them to be ranked according to the degree of environmental danger. Without knowledge of the trajectory of ecosystem successions, it is impossible to offer adequate requirements for the technologies used to ensure the implementation of the preserved natural potential after the removal or reduction of man-made stress."

Jan 1, 2018

By D. Pirouzan

It is customary to use more than one stage of flotation to obtain an acceptable level of separation of valuables. Flotation circuit design is usually accomplished by applying empirical rules which usually results in operations not working at their optimum conditions. Given the capabilities of genetic algorithms (GA) in finding an optimum solution in a very disturbed search spaces, they can be used to obtain the desired flotation circuit configuration. In flotation circuit configuration and optimization problem, a combination of metallurgical parameters such as yield and concentrate ash content could be used as the fitness function for the genetic algorithm. The multi-objective nature of the problem justified to use Pareto method to arrive at a set of solutions. The appropriate configuration based on technical or economical considerations could then be chosen. To obtain the fitness function for any given configuration, it is necessary to model every flotation stage. The proposed method was used to find the optimum circuit configuration for a coal washing plant. The objective was to arrive at the highest yield while producing a concentrate with a certain ash content (< 11%). The feed to the flotation circuit was characterized based on the size fractions and their flotation rate constants. Results showed that with a 95% confidence, the absolute difference between the modeled and measured values were 2.9-5.5% for yield and 0.4-1.1% for concentrate ash content. When the proposed GA-based circuit configuration was implemented in the plant, the yield increased from the original value of 57.6% to 65.7% while producing concentrate ash content (10.9%) within acceptable limits. By adding one stage to the current three-stage circuit, it was predicted that the yield could further increase by 3.8% while keeping the quality of the concentrate within the appropriate level. Keywords: modeling, optimizing, flotation circuit configuration, genetic algorithms

Sep 1, 2012

By Shibayama A.

In this research, an investigation of a process to selectively remove arsenic (As) and antimony (Sb) contained in enargite (Cu3AsS4) and tennantite/tetrahedrite ((Cu1,Fe)12(As,Sb)4S13) copper resources by leaching and precipitation were performed. First in the leaching process, the target was to selectively leach As/Sb and reduce their contents in the ores to <0.5 wt% followed by a second process to remove As/Sb dissolved in solution for environmental control. Enargite ore contained 3.65 wt% As while tennantite/tetrahedrite ore contained 5.40 wt% As and 4.85 wt% Sb. Alkaline leaching using NaHS?NaOH media at varying experimental conditions (temperature, pulp density, time, reagent concentrations) were performed to investigate the process. As/Sb precipitation studies were also performed to control high As/Sb concentrations in leach solutions by using elemental sulphur (So). Results from leaching studies showed that over 99% of As/Sb in the impure copper ores can be removed and their contents in the final solids reduced to <0.5 wt%. It was also established that such very high leaching could be achieved at 80°C within 1?6 h and pulp densities as high as 1000 g/L. The study also revealed that leach solution containing very high As/Sb concentration ranging from 5 to 20 g/L can be used as fresh solution for leaching of fresh ores until concentrations exceeding 35 g/L when it was sent to precipitation circuit for As/Sb removal. Addition of elemental sulphur at 90°C and fast cooling to 30°C allowed over 60% As/Sb precipitation and removed as Na3AsS4 and solution with reduced As/Sb concentration to leaching circuit for continuous use. Keywords: Enargite; Tennantite/Tetrahedrite; Selective Leaching; Precipitation; Sodium hydrosulfide;

Sep 1, 2012

By A. K. Suri

India plans to increase the nuclear power share in overall energy-mix to about 30% by 2032 using both indigenous and imported reactor technologies. In the immediate time-frame, it is envisaged to generate 10000 MW electricity by PHWR technology by 2020 using indigenous uranium resources. This necessitates setting-up of new uranium mills and augmenting the existing resource, mining and milling capacities. This paper describes the current status and future R & D needs towards achieving the targeted demand of yellow-cake. Keywords: uranium, hydrometallurgy, leaching, yellow cake

Sep 1, 2012

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014

By Z. Pokrajcic

The traditional comminution circuit is a major consumer of energy ? both as electrical energy and through consumption of media and wear resistant liners. Up to 40% of electrical energy con-sumed at a mine site is attributed to comminution however only a few percent of this energy is used in the generation of new surfaces from size reduction. This paper describes the evaluation of modifications using simulation models based on two operating comminution circuits. The aim of these modifications is to decrease both the amount of electrical energy consumed in the size reduction process, known as direct energy, as well as to decrease the consumption of grinding consumables such as steel grinding media and mill liners, designated as indirect energy. The approach is two-fold: ??Employ, where possible, autogenous grinding techniques to eliminate the need for grinding media and reduce mill liner wear. ??Optimise the use of the grinding energy distribution in the comminution circuit by using more energy efficient grinding devices to target typically problematic features of a comminution circuit such as critical size material from the primary mill and overgrinding in the secondary mill. The investigations show that significant total energy savings, as high as 50% in some cases, can be achieved by employing the techniques described while maintaining circuit throughput and product size. Investigations also show potential benefits in downstream flotation processes as the product size distribution generated from the eco-efficient circuit is generally ?narrower? in shape for improved flotation performance and containing less material in the coarse fraction for overall better liberation.

Jan 1, 2014

By T. Sreenivas

This paper describes results of laboratory studies on recovery of dissolved uranium values from alkaline leach slurries of a medium-grade uranium ore from Gogi (Karnataka, India) using the resin-in-pulp (RIP) process. Besides anionic carbonate complex of uranium, the other major ionic constituents of the leach solution are CO32-, HCO3-, SO42- and MoO42-. The total dissolved solutes (TDS) are about 45 g/L. Various commercially available strong bases anionic resin-in-pulp (RIP) grade resins ? both macroporous and gel type, were studied with respect to their loading capacity. Parametric variation studies were then carried out with the short-listed resins. Results of the semi-continuous counter-current extraction and elution tests indicated extraction efficiency of about 98% and practically complete elution of the loaded uranium values with NaCl eluant using a gel type polystyrene based resin grafted with quaternary ammonium ion. Keywords: uranium, hydrometallurgy, ion exchange, resin-in-pulp

Sep 1, 2012

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes are diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favors a different flotation environment. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferential recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rpm, rotor size/type) at the beginning of the row, where flotation is typically froth phase limited and operational, and set-up parameters have a limited influence on the recovery. ? Higher-powered flotation machines (high rpm, high power rotor size/type) at the end of the row to improve fine particle recovery. ? Lower-powered flotation machines (low rpm, low power rotor size/type) to enhance coarse particle recovery. In evaluating the effect of turbulent kinetic energy on flotation performance, the spatial distribution and its effect on size denominated recovery needs to be evaluated. The mean energy dissipation rate is a measure of the bulk energy input, but CFD-based models offer a more introspective view of flotation sub-processes. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced air and naturally aspirated machines. Keywords: CFD-based model, attachment, detachment, energy dissipation, hybrid energy flotation?, forced air, naturally aspirated

Sep 1, 2012

By Patricio Berrios, David Barriga, Peter Amelunxen, Gerson Sandoval, Roger Amelunxen

Laboratory test equipment and methods have undergone relatively little change since their introduction in the 1950’s. The Denver sub-A cell is still by far the most commonly used laboratory batch cell, but bottom-driven and instrumented cells are beginning to appear. Test procedures have also changed little over the past 60 years, and most engineers continue to rely on empirical models for predicted plant scale performance from laboratory scale tests. This approach is problematic, because changes in the froth phase characteristics in the lab hamper the reliability and reproducibility of the empirical extrapolation to plant scale. In a previous work, the authors reported on the impact of froth recovery at the laboratory cell, showing that variability in the froth recovery can lead to significant error in the modeled kinetic rate constant unless it is properly accounted for in the scale-up model. In this work, we review the role of hydraulic entrainment in the lab cell, and how variability in particle specific gravity, shape factor, and froth residence time can impact the entrainment recovery.

Jan 1, 2014

By V. A. Chanturiya

The application of High-Power Nanosecond Electromagnetic Pulses (HPEMP) irradiation in dressing of resistant gold- containing ores appears attractive as this technique provides for a significant increase in precious metal recovery (30-80% for gold and 20-50% for silver), therewith helping reduce both energy consumption and the cost of products. The prospects for applying pulsed power technologies in the mineral processing in order to increase the contrast between the flotation properties of raw minerals dictate the need to perform special studies of the effect of HPEMP on the structural state, phase composition, and physical and chemical properties of surfaces of sulfide minerals as the main carriers of precious metals. This study deals with plausible mechanisms of the micro- and nanophases formation on the surfaces of sulfide minerals under the effect of high-power nanosecond electromagnetic pulses (HPEMP) with high electric field strength ~107 V/m. This paper discusses reasons for the changing of flotation behavior of natural pyrite and arsenopyrite during the pulsed-power treatment. It was concluded that HPEMP treatment may be regarded as a tool to change the surface composition and sorption ability of collector (xanthate) onto mineral surface, and, therefore, it allows to control the hydrophobic-hydrophilic surface balance. Single mineral flotation tests have been shown the significant increasing of the pyrite recovery while the arsenopyrite was depressed. The results of gold containing pyrite (pyrrhotite)-arsenopyrite ore flotation in batch approve the decreasing of arsenic recovery in sulfide concentrate. Keywords: pyrite, arsenopyrite, high power nanosecond pulses, activation, selective flotation

Sep 1, 2012

By J. Gong

Fine mineral particles pose two challenging problems in froth flotation, i.e., ineffective recovery of fine hydrophobic particles and mechanical entrainment of fine hydrophilic particles. The first problem has attracted much research effort while the second problem has received much less attention. We have recently proposed a method to deal with mechanical entrainment, i.e., utilizing the flocculating power of polymeric depressants to flocculate fine gangue particles and making the flocs big enough so that the mechanical entrainment of these particles can be reduced or eliminated. In this paper, we report results on the use of polyethylene oxide (PEO) in controlling quartz gangue in the flotation of sulphide ores. PEO was found to flocculate fine quartz and lower its entrainment. It was also found to modify air/water interfacial properties and acted as a frother, which could increase gangue entrainment. Nevertheless, when used at starvation dosages, PEO was found to significantly improve the grades of the floated sulphide concentrates.

Jan 1, 2014

By S. Castro

The aim of the present paper is to review the current technologies for arsenic removal in the copper metallurgical industry, and to show the progress made with some promising emerging strategies, involving the pre-treatment of copper-arsenic concentrates by selective flotation or by alkaline leaching with Na2S-NaOH solutions. The advantages of alkaline leaching are the selective dissolution of arsenic and antimony, the high extraction yield, and the practically nil loss of copper, which remains in the clean copper concentrate as a CuS residue. Alkaline ?cured? ? a procedure similar to ?acid-cured? in conventional leaching ? improves arsenic extraction and reagent consumption, making this an interesting technology for the treatment of high As-Sb concentrates. In light of recent advances on the selective flotation of enargite and tennantite, the importance of redox conditions to control the flotation/depression of enargite-tennantite from copper sulfides has been well established. However, problems of selectivity must still be solved. Additionally, the limitation imposed in some cases by the need to recover the molybdenum by-product must be considered. The application of selective flotation to obtain a high-arsenic or ?dirty? concentrate and its sub-sequent treatment by the alkaline leaching process is suggested.

Jan 1, 2014

By A. M. Raichur, S. P. Vijayalakshmi

Fine coal dewatering is a major problem in the coal industry because the fines hold significant amounts of water and account for two-thirds of the product surface moisture. Present methods include flocculation using polymeric flocculants followed by filtration. But the kinetics of filtration are not favorable with such flocculants. In this study, a novel method involving flocculation with microorganisms for improving the settling rates and dewatering kinetics has been investigated. Two Gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis were used as bioflocculants. The effect of time, pH and ionic strength of the electrolyte used on adhesion and flocculation were studied. Adhesion tests showed that maximum adsorption occurred in 20 minutes in the pH range of 2-7 and the total amount of bacteria adsorbed was almost the same with both the flocculants. Nearly 98% of the coal flocculated with both the microorganisms in about 5 minutes. The filtration rate of fine coal almost doubled with addition of bacteria and electrolyte and maximum filtration occurred near the point-of-zero-charge of the bacteria.

Jan 1, 2003

By Hamid-Reza Manouchehri

"The triboelectric charge attributes of feldspar, quartz and wollastonite minerals, after contacting different triboecharging medium made of different materials, were considered. Their charge acquisitions by different size fractions of minerals were monitored and accordingly their energetic work function values were estimated. Moreover the separation behaviours of these minerals through the electric field of a laboratory free falling separator were determined and the effects of some chemical reagents on separation their separation characteristics were studied.Finally an attempt was made to translate the findings from single mineral systems to a complex silicate ore, containing quartz, feldspars, wollastonite and some other silicates. The results show favourable prospect to apply the triboelectric separation technique for beneficiation such a complex raw material."

Jan 1, 2003

By Peter Riccio

Oxiana Sepon?s mineral processing facility in south central Laos produces copper cathode using leach-autoclave-SX/EW flotation technology. Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid for the leach circuit. However, low pyrite recovery has been an ongoing challenge in the flotation circuit. Tailings characterization work done by Ian Wark Research Institute showed that the pyrite losses to the tail are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines. In December of 2005, a joint Cytec-Oxiana technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt, and was un-available for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the Sepon low pH, high dissolved metal ion environment, and will not complex with ferric, ferrous, or copper in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which then was followed by on plant testing that showed a step wise improvement in pyrite recovery.

Jan 1, 2014

By M. Taheri

Multiple Attribute Decision Making (MADM) method is applied to select tailings site of the Gol-e-Gohar Iron Ore Processing Plant in the Kerman province, south-eastern of Iran. To select tailings site, screening is applied on eight location proposed by Binnie and Granges. Consequently three sites identified for further studies. Evaluation factors include only the most important factors such as efficiency ratio, elevation and distance to processing facilities, occurrence of faults and fractures. Crisp values such as efficiency ratio, elevation and distance can be determined by measurements and calculations, but some factors such as occurrence of faults and fractures are presented as linguistic values that can be described with triangular fuzzy numbers. Based on evaluation values obtained an optimal tailings site can be selected using a modified Technique of ranking Preferences by Similarity to the Ideal Solution (TOPSIS) given crisp data and linguistic variables as the alternatives of attributes. Each attribute?s weight is assigned using the analytic hierarchy process. The final ranking order aids in the selection of tailings site. Finally, the stages of modified TOPSIS method were applied and site No.2 situated in 5400m to the mill was selected as the best alternative.

Jan 1, 2014

By F. M. Zafar Kaifi

Magnesite producing companies rely on high grade purity MgO. The mineralogy of magnesite has a significant impact on the manufacturing of magnesite bricks. The manufacturing process of bricks companies utilizes 90% magnesite from 85%~90% MgO. The main objective of the magnesite bricks was to utilizes the indigenous raw material available in bulk quantity. With better under-standing of chemistry of the mineral species and strict control of bricks manufacturing/processing conditions can be better produce efficiently, a low cost high quality bricks with minimum detrimental environmental impact.

Jan 1, 2014

By Alexsandro Berger

Many thickener operations continue to be constrained by their ability to process consolidated underflows with high yield stress and associated rheological characteristics. To maximise separation efficiencies within a thickener operation the use of both engineering and reagents are always considered. BASF is developing a Novel Flocculant Technology (NFT), which combines both of these aspects to enhance the performance of the thickener operation, improving the areas of pumping efficiency, underflow density and throughput. The development progression through stages of laboratory scale batch test work to pilot scale dynamic testing has demonstrated the ability of BASF NFT to maintain effective flocculation performance whilst increasing the rate of underflow consolidation, and significantly reducing the associated underflow yield stress of the treated material. This paper will present application data through full scale dynamic testing conducted on a granite washing circuit to demonstrate the performance benefits that NFT offers to a thickener operation. Compared to the conventional flocculant treatment, within the operation parameters and conditions employed during the full scale trials, the NFT produced a reduction in underflow rheology (yield stress) of around 45 % relative to a given solids and improved the underflow consolidation by providing at least 20% relative higher underflow solids loading than the upper limit of the given typical thickener operation. Keywords: flocculation, thickener operation, rheology, yield stress, underflow density, throughput, slump test

Sep 1, 2012

By Ö. Genç

In this paper, full-scale mill data collected from three different circuit configurations in cement plants demonstrated the size reduction performance of dry ball mills in relation with the ball size classification achieved by the classifying liners used in the grinding compartments. Findings indicated that, breakage rates at the last 2 ~ 4 meters of the mill are not sufficient to give reasonable size reduction ratios for the production of fines. Application of only damming rings without classifying liners resulted in inverse ball size classification which lead to reduction in size reduction performance thus specific breakage rates.

Jan 1, 2014