Search Documents

By Burrows D. R.

Metal-rich sediments precipitating from hot saline brine pools were first discovered in 1965 in the Red Sea.1-2 The subsequent discovery of high temperature black smokers and associated massive sulphides in 1977 at latitude 21oN on the East Pacific Rise3 came more as a confirmation than a revelation. Formation of massive sulphides through precipitation from circulating sea-water had been predicted by Oftedahl in 19584, and the mechanisms well evaluated in basaltic-hosted Cyprus-type 5 and in Kuroko-type deposits.6,7 Sea-floor exploration from 1977 through the 1980?s in sediment-starved mid-oceanic ridge (MOR) settings had little impact on land-based exploration. This is primarily because: a) MOR spreading centres were recognized as poor analogies to even Cyprus-type basalt-hosted deposits; b) their preservation potential was limited due to rapid oxidation and c) the metallic deposits studied were small and therefore not directly comparable to the far larger ore bodies on land. More recently underwater mineral deposit research has focused in a variety of back-arc environments associated with felsic submarine volcanism, environments more similar to those predicted for the formation of Kuroko-type deposits (e.g. Okinawa Trough, 8 Lau Basin, 9 Manus Basin, 10 Aeolian arc, 11). Most studies, while scientifically interesting, were hampered, in general, by a lack of good descriptive data, a reliance on isolated grab samples, and a lack of sub-surface observations. This research has therefore had only limited direct impact on exploration strategies with the possible exception of research conducted in areas where faulting provided enhanced vertical exposures. 12

Jan 1, 2011

By V. K. Banakar

The occurrence of hydrogenous ferromanganese encrustations (Fe-Mn crusts) on the Cretaceous age Afanasiy-Nikitin Seamounts (ANS) in the eastern Equatorial Indian Ocean (EEIO) was first reported by Banakar et al. (1997, Marine Geology). The major element composition of the samples from the upper flank of the ANS (~1650 m water depth) indicated enrichment of Co up to 0.9 % (Parthiban and Banakar, 1999, Indian Mineralogist). Subsequently a project supported by the Department of Ocean Development to explore the ANS for Co-enriched Fe-Mn crusts was launched in 2002 by the National Institute of Oceanography. Sampling at regular depth intervals along two transects on the slopes of the northern elevated region of the ANS was carried out. The Fe-Mn oxide deposition is evident on almost all types of substrates viz., basalts, conglomerate limestone, fossil corals etc., and the thickness of the oxide layer varies from a patina to 7 cm. The Fe-Mn crust growth is evident only above a water depth of 3200 m, below which semi-lithified carbonate ooze is dominant. The ANS Fe-Mn crusts from all the water depths exhibit Mn/Fe < 1.5 suggesting pure hydrogenetic accumulation of metal-hydroxides. Bulk sample Ce-contents for a few selected depth-representative samples are remarkably high, up to 3700 ppm with an average of ~2500 ppm. The positive Ce-anomaly decreases from ~8 at 1600 m depth to ~1.6 at 3200 m depth, which is in contrast to the modern dissolved oxygen depth-profile in the region. This observation suggests that major time-period of the Fe-Mn crust accretion history is dominated by ambient waters with lower-oxygen at deeper depths than at the intermediate depths. This in turn probably suggests a major reorganization in the deep-intermediate hydrography of the region in the past.

Jan 1, 2005

By Harold Gibson, Ulrich Schwarz-Schampera, Ralf Freitag, Hendrik Mueller

INTRODUCTION Germany has a long history in marine research in the Indian Ocean. The first German scientific cruise started in 1964, followed by a series of state-sponsored research cruises between 1983 and 1995 leading to the first finding of polymetallic sulfides in the Indian Ocean. The research included regional bathymetric, geological, structural, volcanological, petrological and hydrothermal investigations along the Carlsberg Ridge and the Central Indian Ridge (CIR). Early environmental base line studies covered oceanographic and sedimentology aspects. In 2010, BGR took the initiative for the preparation of a license application for the exploration of polymetallic sulfides with the International Seabed Authority (ISA), and prospecting started in 2011 along the southern Central (CIR) and the northern Southeast Indian Ridge (SEIR) in the southwestern Indian Ocean (cruises INDEX 2011 on board R/V Sonne), INDEX 2012 (R/V Fugro Gauss), INDEX 2013/1-2 (R/V Sonne) and INDEX 2014 (R/V Pelagia). After three years of resource-oriented and environmental base line studies, BGR, in order for the Federal Ministry for Economic Affairs and Energy (BMWi), applied for an exploration license which was approved by and subsequently signed with the ISA in 2015. The license gave permission to start a detailed exclusive resource-oriented exploration program in the license area. The program includes the outline of potential ore deposits and a resource assessment but also extensive and detailed base line studies for the sustainable protection of the marine environment in the license area. The license contract has a fifteen years lifetime and may allow the application for a subsequent mining license. The exploration aims at the identification of inactive polymetallic sulfide deposits, formed below former discharge zones of hot hydrothermal fluids on the ocean floor (“black smoker” systems), by advanced and modern exploration techniques.

Jan 1, 2018

By S. E. Boyd

Studies of benthic recolonization following the cessation of dredging in U.K. waters and elsewhere are limited, and are largely confined to experimental circumstances. Investigations of the physical and biological status of licensed areas in the U.K. at various times following cessation of commercial dredging are very limited and so judgments as to the likely progress towards environmental restoration and the time-scales are often based on predictions rather than real data. This study was established to address this deficiency by assessing the status of seabed substrata and associated benthic fauna within and outside areas where dredging had ceased and to conduct follow up sampling to monitor progress towards full recolonization.

Jan 1, 2004

By H. I. Chesalova, M. Ye. Melnikov, A. M. Asavin

The discovery of iron-manganese ores on the surface of underwater mountains was made more than a half century ago. During this time the basic ideas about the thermodynamics of the processes of hydrochemical reactions in the sea water have been developed by scientists and are revealed in geochemical and mineralogical differences between the deposits from the seamounts and the nodules of the sea bottom. The distribution of the dissolved metals, oxygen, carbonic acid and organic matter in the overlying ocean waters of seamounts in the deep ocean to depths more than 5,000 m has been studied in some detail (e.g. J.R. Hein, P. Halbach. G.B. Baturin, Ye.M., S.I. Andreev, L.I. Anikeyeva, [1-6]). In recent years scientists from YUZMORGEOLOGY have completed detailed geological survey work on the Magellan Seamounts in the Pacific Ocean. The results of drilling the ore body and geophysical and photo surveys have also been described [4]. Previous ideas about the general covering of seamount surfaces with iron-manganese crusts have been changed based on ground-truth surveys. This study examines the complex concentric-zone or spotty arrangement of the most densely covered sections, the strong dependence of the thickness of crust on the geomorphologic features, and the potential influence of the underlying substratum. One established geochemical heterogeneity in the composition of ores, also frequently inversely proportional power dependence on directions was observed. The development of a numerical model of the formation of the ore crust on the seamounts is currently a high priority.

Sep 24, 2006

By Richard H. T. Garnett

Marine mining on the continental shelf was first attempted in 1900 for gold off the beaches of Nome, Alaska. Attempts continued until 1990 with cutter-suction, airlift and bucket-ladder dredges. Offshore Thailand profitable production of tin resulted from clamshell, bucket-ladder and trailing suction hopper dredges. Today in Indonesia numerous bucket-ladder dredges continue to mine tin. Off the coast of Namibia and South Africa nearly a dozen large and medium sized vessels are engaged in diamond production. The obvious risk results from the working environment. Vessels and lives have been lost in the past. At best the availability of mining equipment is reduced. Leaving aside the marketing and financing aspects, otherwise the most important risks are technical. They manifest themselves as diamond production short-falls with obvious financial consequences. Bias and deficiencies in sampling equipment and procedures may result in misleading grade estimates, even serious under-estimation. Inadequate sampling in terms of sample support and density may result in over-optimistic grade determinations, especially if under-sized mining blocks are outlined. Quantitative measurement of the geotechnical characteristics of the sediments to be mined is an essential stage in a feasibility study. Without a full understanding of the bedrock profile and the overlying sediments the ease, completeness and speed of excavation during the mining process cannot be properly estimated. Both historically and at present the greatest negative discrepancies from production estimates result, not from grade shortfalls, but from significantly lower mining rates than thought possible by the operators. The learning curve in marine, production mining is steeper and longer than is generally recognised by newcomers to the industry. Examples are provided from tin, gold and diamond mining experiences.

Jan 1, 1998

By Cheong-Kee Park

Since 1983, Korea Ocean Research and Development Institute (KORDI) have performed surveys on deep-sea mineral deposits in various areas with respects to their occurrences in Pacific ocean including manganese nodules in the C-C area of Northeast Pacific, Co-rich manganese crusts in various seamounts of West Pacific and hydrothermal sulfide deposits in back arc basins of Southwest Pacific. Among the results of these activities of KORDI, remarkable things were the registration as a pioneer investor in 1994 through the Government of Korea and the accomplishment of relinquishment on the allocated area in 2002 according to the relevant regulations. KORDI is faced to handle detailed surveys to select the optimum mining sites in the allocated area of 75,000 km2 and environmental studies to meet the requirements of the regulations or recommendations of the ISA. In respects of future exploration strategies, it is considered that methods and tools of previous exploration activities should be changed to the highly advanced technology. Establishment of an advanced exploration system and actual practice in appropriate areas become one of important tasks of KORDI in exploring deep-sea minerals, particularly manganese nodules. A technical strategy for future detailed surveys in the allocated area is realization of simultaneous and precise data acquisition on bottom information, such as variations of microtopography, nodule distribution, and transparent layer thickness of sediments in relatively small area (10 km x 10 km) representing certain specific regions, by high resolution survey technology. It would be not only a challenge for new exploration system in deep-sea environment, but also a mission for deep seabed mining venture.

Jan 1, 2003

By Valcana Stoyanova

Deep-sea mining of polymetallic nodules are expected to produce serious impact on benthic ecosystem due to removal of nodules, sediments and associated fauna by means of collector, and subsequently, by the resettlement of sediment plume which may affect seabed biota outside mining tracks through blanketing, smothering and feeding interruption. The scale and magnitude of the exact impact of commercial operations is not known at present, but its assessment strongly required acquisition of the adequate environmental baseline information. During the past two decades, IOM carried out a total of 20 research cruises in the eastern part of Clarion-Clipperton Zone (CCZ) with purpose to obtain essential data and information on polymetallic nodules and to prepare for future development their deposits. Whilst evaluating the nodule coverage at particular station from both seafloor photographs and box-core recoveries it was ascertain that the ground-truth data plotted against the photo data indicated substantial differences between two methods. Understanding of this phenomenon has not only the methodology meaning related to the efficiency of the using photoprofiling techniques during exploration of nodules, but also it could be of environmental importance because the similarity between natural sediment blanketing occurrence in studied area and expected re-deposition and blanketing of sediments which will be disturbed during mining operations.

Jan 1, 2011

By Øystein Sture, Kurt Aasly, Ben Snook, Sigurd A. Sørum

INTRODUCTION Efficient exploration methodologies for base metal deposits have huge benefits for future deep sea mining endeavours, and underwater hyperspectral imaging (UHI) has been variably demonstrated to have applications in the identification and characterisation of mineralisation on the seafloor for both nodules and seafloor massive sulphides (SMS) (Dumke et al., 2018 and 2017 respectively). Due to growing resource requirements (Singer, 2017), SMS deposits are considered to be increasingly significant sources of copper and zinc, as well as silver and gold. This style of mineralisation is currently occurring at active hydrothermal vents (black and white smokers) but now-inactive sites also have the potential to be large mineral deposits. As such, the development of novel methodologies to detect both on-going and extinct mineralisations are of high importance. Geological setting During the MarMine cruise (Ludvigsen et al., 2016), non-mineralised host rock, low grade ore and high grade ore grab samples (Snook et al., 2018) was collected by ROV from the Loki’s Castle deposit (Pedersen et al., 2010), located on the Mohn’s/Knipovich junction on the ultra-slow spreading Arctic Mid-Ocean Ridge (AMOR), at a depth of approximately 2300 m. This material has been characterised as part of the MarMine project (e.g. Snook et al., 2017), and, by imaging compositionally constrained material, the measured hyperspectral responses can be used to generate a library for identification of deposits on the ocean floor. UHI technology Remote sensing with hyperspectral and multispectral technologies has seen wide use in prospecting for ores and hydrocarbons on land (Van der Meer et al., 2012). Iron oxides and sulphides have low blue reflectance and high red reflectance in the visible spectrum. The ratio between these two pairs has been used in exploration for terrestrial deposits of hydrothermal origin (Sabins, 1999). This discrimination typically also includes wavelengths exceeding the visible spectrum (1.5µm – 2.5µm). These wavelengths are typically not utilised underwater because infrared wavelengths and higher are rapidly attenuated in water. However, discrimination based on the full shape of the spectral response in the visible light (350nm – 800nm) may still be possible (Bolin and Moon, 2003). Resolving the endmembers from the spectral responses requires prior knowledge about the optical properties of the materials, i.e. their reflectance. These reflectances can be obtained in a controlled environment, where the spectra of the lamps, wavelength- dependent attenuation in water and scattering of light can be accounted for (Johnsen, 2013).

Jan 1, 2018

By Toru Yamasaki

"Bimodal lithostratigrafic assemblages are of significance in volcanogenic massive sulfide (VMS)-hosted lithology. The largest deposits are either bimodal-siliciclastic or maficsiliciclastic, and the presence of a significant siliciclastic component in the host stratigraphic succession favors large VMS deposits (e.g., Franklin et al., 2005; Barrie and Hannington, 1999). In the case of modern sub-seafloor VMS deposits in arc-related settings, the majority of deposits have been discovered in association with calderas or cauldrons (Halbach et al., 1993; Ishibashi and Urabe, 1995; Iizasa et al., 1999). These features are formed by the explosive eruption of silicic volcanoes, so that silicic host rocks and/or pumiceous volcanic clasts are generally observed around the ore deposits (e.g., Binns and Scott, 1993; Fiske et al., 2001). Caldera-like and graben-like morphological features therefore attract attention in geophysical surveys. However, silicic lithologies (dacite and rhyolite) normally contain only small amount of metallic elements (e.g., a few ppm to a few dozen ppm of Cu), whereas mafic rocks, such as basalts and basaltic andesites, contain significant amounts of metals (e.g., a few hundred ppm of Cu). Thus, the origin of metallic elements in VMS deposits associate with the silicic host rock remains unclear.The Iheya North Knoll is a volcanic complex in the middle of the Okinawa Trough. It is located in a young and actively spreading back-arc basin that extends for 1200 km behind the Ryukyu arc-trench system (Lee et al., 1980; Letouzey and Kimura, 1986). Several active hydrothermal fields have been recognized in the Iheya North Knoll. Mineralization at the Iheya North Knoll is characterized by relatively juvenile features consisting of VMS deposits with associated hydrothermal alterations to various degrees. Massive sphaleriterich sulfides at this site, recovered for the first time from beneath an active seafloor hydrothermal system, strongly resemble the black ore of the Kuroko deposits of the Miocene age in Japan (Takai et al., 2011). From February 11 to March 17, 2016, the SIP CK16-01 (Exp. 908) D/V Chikyu cruise was conducted at Iheya North Knoll and the rifting center of the Iheya Minor Ridge area, middle Okinawa Trough. The Iheya Minor Ridge area is also an active hydrothermal field, located ~30 km southeast of the Iheya North Knoll. In this area, basaltic rocks are widely distributed, and drilling has confirmed that the basaltic materials continue to ~120 m below the seafloor (Kumagai et al., in prep)."

Jan 1, 2017

By Ivar Eskerud Smith, Ole Jørgen Nydal, Niranjan Reddy Challabotla, Svein Sævik

INTRODUCTION Airlift pumping, utilize compressed air that is injected at the bottom of a vertical pipe submerged in the water, reduces the mixture density inside the pipe and lifts the liquid or mixture of liquid and solids. This type of pumping technology, which is simple and without moving parts submerged in water, which provides several advantages compared to the mechanical pumping. Airlift is used in various difficult pumping applications such as transport of fluids corrosive to metals, explosives, nuclear and toxic materials in chemical industries, diamond mining and coal transport. Application of airlift to deep sea mining conditions was investigated by extensive laboratory experiments [1], theoretical analysis [2], and limited proof of concept field studies [3] starting in 1970’s with the discovery of huge amounts of manganese nodules discovered on the seabed at a depth of ranging from 4000 to 6000 m . Even after extensive investigations over the last five decades, there exists no commercial application of airlift technology for lifting of minerals. The major problems with the application airlift for deep ocean mining was (a) lack of control over the expansion of the injected gas, which increases the velocity in upper part of the riser pipe (b) lower efficiency compared to mechanical pumping [3]. Different flow regimes are encountered in airlift pumping: bubble, slug, churn and annular flow. Annular flow regime is the least efficient in lifting of particles and churn flow has better efficiency [3].

Jan 1, 2018

By Andrew E. Grosz

The Atlantic Continental Shelf (ACS) of the United States includes about 391,000 km2 extending from the shoreline to the 200-m isobath. It varies in width from a fraction of a kilometer (offshore of southern Florida) to about 150 km (offshore of Cape Cod, MA). The contained volume, of sand and gravel is estimated to be on the order of 3-7 x 1.011 m3. Concentrations of potentially commercially important heavy minerals (HM) exist locally, particularly in high-energy depositional environments (for example in channels, tidal deltas, ridge and swale areas, and submerged former shoreline complexes). Recently completed and ongoing studies of HM assemblages in vibracore samples from the south shore of Long Island Sound, NY, offshore of Ocean City, NJ, offshore of Cape May, NJ, offshore of the mouth of Chesapeake Bay, VA, offshore of Myrtle Beach, SC (grab samples), and the ACS offshore of Florida provide the information base for this presentation (Table 1). The surficial sediments of the ACS contain local concentrations of HM that compare favorably to those in currently mined onshore deposits as shown

Jan 1, 1988

By Charles W. Finkl

Coastal and marine aggregate (sand and gravel) mining on US continental shelves is a major activity that supplies industrial and commercial demands for these raw materials. Because Pacific, Atlantic, and Gulf coasts contain significant shoreline segments that are in a critical state of erosion, sand-gravel and mixed sediment (sands with a high percentage of silt-plus-clay) deposits are mined in efforts to mitigate land loss. Sandy shores, and to a limited extent gravel coasts, erode by shoreline retreat due to relative sea-level rise and sediment starvation in littoral drift patterns. Mostly gravel shores occur in high latitudes and shorelines often advance seaward due to isostatic rebound following the LGM (Last Glacial Maximum 18,000 YBP). Sandy and fine-grained shores occurring in middle and low latitudes of the conterminous United States are problem coasts that require beach renourishment and reconstruction of barrier islands. Muddy coasts of the Mississippi Delta region are especially problematic because some islands are literally disappearing in response to subsidence. Replacement of sediments lost to the littoral drift system or returned to sedimentary sinks by drowning is thus a critical endeavor that involves annually dredging hundreds of millions of cubic meters of sediments from the continental shelf area. The types of shelf sediments that are amenable to marine mining techniques, their occurrence, and means of detection are highlighted in this paper. Minable Sediments on the Continental Shelf Wide varieties of sedimentary bodies that occur on the continental shelf are amenable to mining for beach renourishment and barrier island (beach-dune-marsh system) reconstruction. Relict terrestrial deposits make up a small but important proportion of shelf sediments that were deposited on coastal plains, now drowned by the post-glacial sea-level rise to form continental shelves. Examples of these deposits include drowned moraines, outwash plains, eskers, and kettles along the northern Atlantic coast in addition to siliciclastics along middle latitude Pacific, Atlantic, and Gulf coasts. Special cases include carbonate sequences along tropical costs of Florida and the muddy coasts of deltas, mostly in Louisiana. Specific types of minable deposits thus include shoreface attached sand sheets, dunes, and ridges in addition to offshore inter-reefal sands (between coral reefs in the Florida Reef Tract), bank deposits, and sand waves (ridges) that extend into US territorial waters. Nearshore siliciclastics include ebb-tidal deltas and bars. Drowned river valleys occur along all three US coasts and can be exploited for their fluvial sands if the covering mud sheets are thin.

Jan 1, 2005

By Peter A. Rona

Investigations of the Gorda Ridge within the proclaimed U.S. Exclusive Economic Zone off northern California and southern Oregon, and the Mid-Atlantic Ridge extending along the center of the Atlantic Ocean, have received new impetus from the discovery of hot black smokers, sizeable polymetallic massive sulfide deposits, and vent animals at the Mid-Atlantic Ridge by the NOAA VENTS Program in 1985. Prior to that time, the oceanographic community focused investigations of seafloor venting at the faster-spreading oceanic ridges of the Pacific Ocean including the East Pacific Rise, the Galapagos spreading center and the Juan de Fuca Ridge because a consensus held that the faster spreading rates at these ridges were necessary to supply the heat to drive black smoker-type venting. As the only oceanic ridge in the Pacific with slow-spreading characteristics, the Gorda Ridge is an outlier of the slow-spreading ridge system that extends through the Atlantic Ocean and western Indian Ocean comprising more than half the 55,000-kilometer-length of the globe-encircling oceanic ridge system. In response to recent discoveries at the Mid-Atlantic Ridge the oceanographic community is shifting more of its activity to investigation of hydrothermal venting and related processes at slow-spreading oceanic ridges. The discovery cruise by a team of NOAA and university scientists followed by

Jan 1, 1988

By G. B. Carpenter

The United Nations Law of the Sea (LOS) Convention includes provisions (Article 76) for establishing the outer limits of a coastal State&apos;s continental shelf and for denoting the seaward extent of sovereign rights over natural resources. Determination of a coastal State&apos;s continental margin, according to Article 76, must consider eight factors: 1. The territorial sea baseline 2. The 2,500-meter isobath 3. The foot of the continental slope 4. A line 200 nautical miles seaward of the territorial sea baseline 5. A line seaward of the foot of the continental slope connecting the points where sediment thickness divided by distance to the foot of the slope equals .01 6. A line 60 nautical miles seaward of the foot of the continental slope 7. A line 100 nautical miles seaward of the 2,500-meter isobath 8. A line 350 nautical miles seaward of the territorial sea baseline Figure 1 shows the preliminary limits for each of the Article 76-based definitions for a portion of the U.S. Atlantic continental shelf. The additional areas gained beyond the 200- nautical mile Exclusive Economic Zone (EEZ) are highlighted. The first three factors are baselines from which the distance provisions of Article 76 are measured. Factors 4-8 are distance- from-baseline provisions for establishing the continental shelf limits. Factor 5, also known as the Depth of Sediment Limit or "Irish Formula", was calculated using sediment thickness data from seismic linesand isopach maps. All other factors were determined from digital hydrographic data. The Depth of Sediment Limit is the most advantageous method for the area shown in Figure 1. It is especially useful for introverted coastlines such as the Georgia Embayment and New York Bight areas. The 200-mile line is advantageous for protruding coasts such as those off major capes, e.g., Cape Hatteras. The 2,500-meter isobath plus 100-mile line gains

Jan 1, 1995

By Philomene Verlaan

Analysis of the relationship between environmental parameters and the content of Mn, Ni, Co, Cu, Fe and Zn in ferromanganese crusts permits improved identification of locations to prospect for crusts with commercially valuable concentrations of these metals. In this study we asked whether a statistically significant relationship exists between primary productivity of the overlying surface waters, the concentration of O2 in and depth of the O2 minimum layer on the metal content of non-hydrothermal ferromanganese crusts in the Pacific Ocean between 130o W and 175o E and 0o to 30o S (the study area). To further develop the interpretation of the results of the statistical analysis and to assess in detail the geographical expression of these parameters in terms of metal content in crusts, a geostatistical technique (kriging) was used to generate contoured values for metal content, primary productivity and O2 concentration in and depth of the O2 minimum layer in the study area.

Jan 1, 2001

By Gerald R. Dickens

Massive sulfide ores and Fe-Mn oxyhydroxide precipitates represent two extremes of a spatial continuum of hydrothermal deposition along oceanic ridges. Elemental variations across this continuum are of interest to economic geologists as a prospective geochemical exploration tool. Theoretical considerations suggest that certain physical and chemical parameters can be used to model compositional variations within the far-field (i.e., Fe-Mn oxyhydroxide) component as a function of distance from ridge axis; however, testing and verification of such models generally has been precluded because the few available distal hydrothermal sediment sequences have been sampled at low resolution and/or are highly diluted with biogenic components (e.g., siliceous and calcareous tests). Recent ocean drilling (ODP Leg 145; Sites 885/886) in the North Pacific successfully recovered an extensive record of "biogenic-free" distal hydrothermal precipitates from an area approximately 60 km south of the Chinook Trough at longitude 168.1 °W. Geophysical and geomorphological evidence suggests the Chinook Trough is the southern lithospheric scar marking initiation of late Cretaceous north-south rifting, implying that recovered hydrothermal materials record distal hydrothermal precipitation from the now-subducted Kula-Pacific spreading ridge. The Chinook Trough hydrothermal sequence is a continuous 15 my record of "biogenic-free" hydrothermal Fe-Mn oxyhydroxide precipitation mixed with eolian clays. It was deposited during the late Cretaceous, early Paleocene (80-65 Ma) as the perpendicular distance from ridge axis increased from 75 to 600 km. A high-resolution geochemical analysis of this hydrothermal sequence reveals distinct trends for the up-core (equivalent to increasing distance from ridge) distribution patterns of Fe, Sc, As, and rare earth elements (REE). Iron concentrations exhibit an S-shape distribution pattern with respect to increasing

Jan 1, 1994

Massive sulfides discovered in 1991 and further explored in 1993 in the eastern Manus back-arc basin, north of Papua New Guinea, represent one of the few modem seafloor occurrences known to he associated solely with highly siliceous volcanic rocks. As such they are very close analogs of ancient volcanogenic massive sulfide (VMS) ore deposits, and hence an excellent natural laboratory for developing new approaches for land-based VMS exploration. The Manus Basin lies between the active New Britain subduction zone and volcanic arc to its south and the opposed inactive Manus subduction trench to its north. It is being extended in a complex pattern of short neovolcanic zones and oblique transform faults. In its western sector, relatively mature back-arc spreading has created predominantly basaltic segments with characteristics and mineralization generally similar to those of mid- ocean ridges. At its far east, however, the basin is distinctly immature. The East Manus Volcanic Zone lies between two members of the Manus transform set, and is an en-echelon series of neovolcanic edifices constructed on extensionally thinned island arc crust formed during the earlier manus subduction episode. Individual edifices range from predominantly basaltic to predominantly dacitic in composition. Two of the edifices are known to be hydrothermally active, and a particulate plume with unknown source occurs in the seawater column above a third.

Jan 1, 1993

By J. V. R. Prasada Rao

India is dependent for 60% of its annual requirement of copper and the entire quantity of nickel and cobalt on imports from outside the country. Land-based resources are either too meager or of too low a concentration for economic exploitation. This has prompted the country to look to deep seabed re- sources for meeting its rising demand for these metals. The Ocean Policy of the Government of India announced in 1982 talks about the need to map and assess the availability of minerals in the deep sea and to develop necessary technologies for exploration and exploitation of seabed minerals. To be self-reliant such technologies would have to be largely developed, tested and operated indigenously. The adoption of the Law of the Sea Convention in 1982 gave a fillip to India&apos;s desire to get into the field of deep seabed mining. India applied for recognition as a Pioneer Investor in Ocean Mining in 1983 and received allotment of a mine site of 150,000 km2 in the Central Indian Ocean in August 1987. Simultaneously, the Government has taken up a programme of development of technologies for exploration of the mine site for resource assessment, environmental monitoring also to meet the commitments like relinquishment of 50% of the area to the Preparatory Commission. Technologies for exploitation of these seabed resource like the mining system, transportation and extractive metallurgy have also been taken up for development in various research institutes largely in the government sector. While India&apos;s objective in the long term is to meet the shortage of copper, nickel, cobalt and manganese by the turn of the century, in the short term, the programme aims at application of the seabed mining technologies to meet the immediate needs of the country such as: a. Exploration for oil and natural gas. b. Exploration and exploitation of placer minerals and other deposits at shallow depth in India&apos;s EEZ.

Jan 1, 1994

By Timothy F. McConachy, Christopher J. Yeats, Ray Binns

Various kinds of sediment-hosted polymetallic sulfide deposit are known on land in ancient marine sequences, many tending to be larger and more valuable than massive sulfide deposits genetically associated with volcanic host rocks. Often such deposits are attributed to subhalative or shallow sub-seafloor precipitation processes, and structural control by faulting is commonly evident. Apart from the famous but anomalous Red Sea metallic oozes and several NE Pacific sites (Middle Valley, Escanaba Trough, Guaymas Basin), however, modern analogs of the sediment-hosted polymetallic sulfide category are lacking. Some deposits hosted by volcaniclastic rocks, such as JADE (Okinawa Trough) and Suzette (Eastern Manus Basin) are strictly sediment-hosted, but their formation is associated with the igneous activity and they are better considered a variant of the more abundant volcanic-associated polymetallic sulfide deposits.

Aug 24, 2006