Search Documents

By Fathi Habashi, Ernesto Bourricaudy, Fouad Kamaleddine

Ilmenite occurs in black sand at the mouth of great rivers as in India, or as massive deposits like in Quebec Province in Canada. It is unsuitable for processing into pigment or for metal production because of its high iron content and its low grade. Pyrometallurgical and hydrometallurgical methods have been developed to cope with this problem which resulted in the production of two commercial products that became known as synthetic rutile and Sorelslag. Attempts are also underway to produce TiO2 pigment directly from ilmenite. This report presents a newly developed process called the Magpie process, which enables the production of high-grade synthetic rutile (over 95% TiO2) from low grade ilmenite (10-12% TiO2). Naturally, if such process is applied for low-grade ore it can be applied with advantage to high grade material as well.

Jan 1, 2014

By Edouard Masengo

A long dyke will be constructed in a lake with rockfill placed by end dumping method. Its crest will be at elevation 521.5 m compared to the nominal lake level at 520 m. In the first portion, its height will vary from 1.5 m on a 35.1 m thick tailings layer to 18.3 m on about 0.5 m of tailings. In the second portion, the dyke will be built on native silty clay and will vary from 18.3 to 15.2 m in height. The tailings consist in stratified layers of fine-grained soils showing lateral and vertical segregation. The tailings are compressible and may develop excess pore water pressure on loading. The tailings overlie a thin layer of relatively soft native silty clay. The till beneath the silty clay is considered incompressible compared to the material above. After construction, as the tailings and silty clay consolidate, pore water pressures will dissipate and dyke stability will improve. Since dyke stability will increase with time, the primary concern is its stability during construction. As a result of construction activities, three potential modes of failure were identified and recommendations were provided regarding the measures that should be undertaken to increase dyke stability during construction.

May 1, 2003

By Patrick R. Taylor, T. A. R. Putra

A review of various methods to treat high arsenic copper concentrates through pyrometallurgical processing is presented. Examples are drawn from various past and current operations and research. Various aspects of the engineering alternatives for treatment methods are discussed. Some of the methods discussed include: controlled oxidation roasting, adaptation of some smelter technology to accept higher amounts of arsenic, complete oxidation with arsenic fixation; sulfation roasting; acid baking, soda ash roasting, and others methods. Other topics include: a short discussion of other problematic impurities; the effects of arsenic on copper electro-refining and product purity; and methods for the ultimate disposal, or marketing, of the arsenic. The latest work being done at the Colorado School of Mines on soda ash roasting is also presented.

Jan 1, 2014

By P. R. A. Andrews

"Talc ore from Bakertalc, High water, Quebec analyzing about 60% talc, previously dry ground to about 95% minus 53 µm was beneficiated in an 11.4 kg/ h pilot-plant flotation circuit. A concentrate of 95.9% talc (necessary for paper-grade) was obtained at a recovery at 75.3% by employing 53 g/t of Dowfroth 250 collector at pH 9.2; further cleaning increased the grade to 97.2% talc at a recovery of 57.5%.Flotation of fresh ground 60% minus 44 µm ore at a feed rate of 18.6 kg/ h produced a grade of 96.4% talc with a recovery of 78.2%, using Aerofroth 70 collector a six carbon-branch chain alcohol, at pH 9.2.The similarity in the concentrate grade and recovery between pre-ground and fresh-ground ore indicated that it was not neces¬sary to grind to 95% minus 53/2m to achieve comparable selectivity. A grind of 60% minus 44 pm corresponds to 100% minus 300 µm.Flotation retention times obtained with fresh ground ore indicate 33 min. for combined rougher/scavenger, and 15 min. each for the first and second cleaners.Talc-magnesite flotation separation is explained in terms of physico-chemical forces, with reference to surface charge and adsorption mechanisms."

Jan 1, 1989

By C. Poon

For slope stability, knowledge of major and minor discontinuity sets that form the rock mass fabric is paramount for pit slope designs. Due to the increased awareness of health and safety in mining projects, efforts have been made to limit structural mapping in order to minimize the risk to personnel associated with approaching potentially unstable areas. Recognizing the importance of such safety precautions, Golder Associates Ltd. is applying a combination of techniques including 3D photogrammetry, conventional mapping and drilling with core orientation to enhance structural data collection. Photogrammetry uses digital photographs to produce a virtual model of a rock mass surface. The application of these techniques will be exemplified through an expansion design of an existing open pit. A comparison of stereonets obtained using these techniques showed some agreements, but also highlighted limitations of each method. The application of photogrammetry was found to be very useful in complementing the other existing techniques.

May 1, 2009

Objectives ? New deposits can be found in mature Mining CampsNew Camps ? Volcanogenic Massive Sulfide (VMS) deposits ? polymetallicpolymetallicexamples are desirable exploration targets examples ? Genetic and exploration models for VMS deposits are robustrobust ? subtle but important differences exist between deposits and districts ? sometimes ??neglectedneglected??in resource modeling and exploration efforts ? ReRe-evaluation of a prominent existing camp is rewarding ? update on the exploration strategies currently being applied on a practical level The Falconbridge-Alexis approach includes GoCAD modelling

May 1, 2006

By J. Lebl, S. Bharti, D. J. Cornett

"This paper presents the design and application of blasthole mining to an area at Strathcona Mine previously employing post pillar cut-and-fill. Extensive mining in the area had led to gradually deteriorating ground conditions and post pillar stoping was no longer considered acceptable. Alternative methods had to be investigated.Conventional methods for mining in poor ground were rejected because of the high cost. Blasthole mining was selected because iI offered good productivity and safety with acceptable costs. The design of this approach involved field investigations and the use of numerical modelling to simulate the different blasthole options and their impact on ground stability. The blasthole design incorporated reinforcement with cablebolts, use of a radio-controlled remote LHD unit, large-diameter holes, blast design and wall control. Potentially unstable areas were outlined during mining with ground monitoring instruments and the results used to modify mining plans during the production phase.IntroductionIn underground metal mines there is a need to improve safety and productivity and lower mining costs in order to maintain reasonable rates of return on investment. This requires the application of good engineering design to both mine planning and ground control in order to optimize production and costs and to forecast potential problems during mining. The task becomes more important when extensive mining leads to gradually deteriorating ground conditions, making existing mining methods and techniques no longer acceptable from a safety point of view. Alternative mining methods must, however, be sufficiently productive to ensure profitability. This paper presents an example of the engineering design and operating approach used by Falconbridge in dealing with such a situation at Strathcona Mine."

Jan 1, 1983

By G. M. Ritcey, M. Silver

"The processing of uranium ores produces tailings that could constitute environmental problems. At most operations the tailings are dumped into a designated area, with the ultimate acid drainage occurring if sulphides are present, together with the release of metal constituents to the rivers and streams. If the chemical reactions occurring within the tailings could be predicted, perhaps methods could be developed to either increase or decrease 'the rates of reaction. One such study has been in progress at CANMET during the past three years. The paper describes the use of Iysimeters containing low-grade and complex uranium tailings to determine the effects and interactions of bacteria, sulphides and solvent extraction organics on the release of radionuclides and on acid production. A simulated rain cycle nine-fold the normal was used and the Iysimeters were subjected to timed intervals of light and darkness. As a result, the tests simulated a 25-year period.IntroductionAlthough Canadians derive major benefits from uranium, there are environmental and health consequences, not yet fully understood, from the associated mining and milling operations. A major project at CANMET (Canada Centre for Mineral and Energ y Technology) has the ultimate goal of ensuring that any adverse effects on man and environment, now or in the future, resulting from the processing of uranium should be acceptably low. The magnitude of the task was exacerbated by the fact that the increased demand for electrical energy and the resultant increased prices for uranium oxide during the 1970s led to a rapid expansion in the industry. Annual world demand for uranium was expected to increase 12-15 fold in the next quarter century, with annual requirements of between 200,000 and 300,000 metric tonnes anticipated by the year 2000. Currently, the demand is low and the prices for the oxide have decreased."

Jan 1, 1982

By C. Bourgoin

"The limited development and application of new technologies to narrow-vein mining is currently impeding progress in the industry to a point where productivity, working conditions and operating costs have reached a critical stage in many Canadian mines.In an effort to foster the emergence and application of new technologies, Université Laval, together with other organizations, has carried out a R&D project focussed on the need of identifying new development pos5ibilities and of facilitating the transfer of technology in matters related to underground mining methods and machinery.The first phase of the study consisted of an in-depth assessment of current practices and problems in narrow-vein mining. The second phase was a state-of-the-art survey of mining methods and equipment, together with proposed modifications and innovations. The third phase of the project concerns the experimental development as well as the principal application of various proposed technologies.This paper presents an overview of the organizational, technical and strategic considerations which guided the University group and it serves as well to introduce a newly-published brochure, entitled ""Underground Mining Techniques of Vein Deposits"", which summarizes such work to date. More specifically, a perspective of technological developments applicable to narrow-vein mining is presented."

Jan 1, 1994

By Z. Liang, Z. Q. Liu, X. F. Li, H. L. Zhang

"Dynamic characteristics of frozen soil is important for the safe, effective and rapid construction in cold regions and artificially frozen engineering. In this paper, dynamic characteristics of frozen clay with various low temperature and different strain rate were studied by using Split Hopkinson Pressure Bar (SHPB) test and numerical simulation test. Variation of dynamical parameters and dynamic stress-strain curves of frozen clay were obtained and analyzed. The results of these test show that: Frozen clay exhibits temperature effect and strain rate effect that the failure type tends from plastic failure to brittle failure with the increase of strain rate or decrease of temperature; Under impact loading, frozen clay exhibits three typical dynamic stress-strain curves as strain rate increases, and the maximum strain of frozen clay only linear increases with strain rate.INTRODUCTIONArtificial freezing technology has been widely used in the construction of underground engineering, such as the coal mine shaft, the deep foundation pit, the urban metro and subsea tunnel, etc. Research on dynamic mechanical behavior of artificial frozen soil will provide supports for these artificially frozen engineering (Xu et al. 1998; Ma 2009). However, the dynamic mechanical research on frozen soil is mainly carried out at low frequencies or small amplitudes of the waves, behavior of frozen soil under impact loads or high strain rate loads has not been made clear."

Jan 1, 2015

By Collin Bartlett, H. Storch

"Modern metallurgical processes operating with oxygen enriched air, such as the Outotec Flash Smelter and Flash Converter, generate very concentrated SO2 off-gas, which in combination with Outotec sulphuric acid plant technology allows the production of high pressure steam to be used for power generation. Outotec combines well proven technology of sulphur burning plants for this purpose with metallurgical plants.The application of Outotec’s proven LURECTM process enables processing of SO2 gas of up to 25 vol.-%. This process maximizes the energy recovery from the SO2 oxidation at a suitable high temperature level which can be turned into high pressure steam. The application of the Outotec HEROSTM heat recovery system enables the generation of low pressure steam from the absorption energy released at the intermediate absorption step. Additionally, energy is also recovered in the acid coolers for boiler feedwater pre-heating.The concept of integration of high and low pressure steam in combination with the pressurized operation of the boiler feedwater deaerator, thus heating up the boiler feed water to temperatures around 160…170°C, enables indirect transfer of low pressure steam (for deaerator operation) into more valuable high pressure steam, which improves the degree of heat recovery. This is the characteristic of Outotec’s HEROS+TM process.The increased generation of high pressure steam will in turn enable the generation of more electricity when compared to a standard traditional sulphuric acid process."

Jan 1, 2014

By David R. Ray, Arthur J. Pyron, William F. Thomann

"Proterozoic plutonic and volcanic rocks in the Franklin Mountains, west Texas, exhibit similar values in average concentrations of equivalent uranium (eU), equivalent thorium (eTh) and equivalent potassium (eK) when compared to Proterozoic igneous rocks of the southwestern United States. Variations of radioelement concentrations for all Proterozoic igneous rocks of the Franklin Mountains range from 1.1 to 357.1 ppm U, 2.1to 259.1 ppm Th and 2.5 to 10.2% K.Recent geologic mapping of the Proterozoic rocks in the Franklin Mountains revealed several types of granites previously unrecognized, and these warrant further exploration for U and Th resources. Fluorite-bearing granites and riebeckite pegmatites are likely targets for further investigation, as these have the highest U and Th concentrations compared to all other granites.IntroductionThis is a summary of the paper presented at the CIM Geology Division Uranium Symposium held in Saskatoon, Saskatchewan, September 8-13, 1981. The purpose of this study was to evaluate the distribution of uranium (U), thorium (Th) and potassium (K) in Proterozoic igneous rocks in the Franklin Mountains, and compare radioelement concentrations to Proterozoic igneous rocks elsewhere in the southwestern United States.General GeologyThe Franklin Mountains are located in west Texas and southcentral New Mexico, within the southeastern part of the Basin and Range Province o f the southwestern United States. The Franklins are a complex fault-block range trending northsouth with strata dipping toward the west. Ages of the rocks range from Proterozoic to Cretaceous. Harbour (1972, 1960) provides the most recent account of the general geology of the Franklin Mountains. Most recent accounts of the detailed Pro Proterozoic geology o f the Franklins are provided by Hoffer (1976), Thomann (1980, 1981), Pyron (1980), Ray (1982) and McCutcheon (1982)."

Jan 1, 1983

By L. Dekker

"In 1979 Chevron Standard Limited and Irving Oil Limited intersected a thick, high-grade sylvinite zone in the Windsor Group in the Chevron Irving Malagawatch No. I well in central Cape Breton. This well was the third and final hole of a program designed to evaluate a non-commercial oil discovery made by Chevron Standard's Mineral Staff in 1978 while carrying out base metal exploration. Nine holes were subsequently drilled to evaluate the significance of the potash discovery. The delineation drilling proved the Malagawatch structure to be complex with the potash zone showing erratic grade and thickness distribution. Based on the drill information the potash accumulation at Malagawatch is uneconomic, however, other salt ""structures"" in the Bras d'Or Basin may in time prove to have better potential.History of DiscoveryIn 1972 Cuvier Mines discovered the Gays River lead-zinc deposit (MacEachern and Hannon, 1974) which prompted Chevron Standard's Minerals Staff to carry out a study of the Windsor basins in Nova Scotia (Figs. I and 2). As a result of this program several carbonate-hosted lead-zinc prospects were identified in the basal Windsor carbonate; one of these was at Malagawatch on Cape Breton Island . In 1978, after preliminary exploration surveys, a diamond drill program commenced consisting of 5 BQ holes (Fig. 3), three of which tested the basal carbonate. Instead of the reefoid bank facies of the Gays River Formation (Giles et al., 1979), the favoured host for economic base metal mineralization, this carbonate was developed as a laminated, pelletoidal, lime packstone more characteristic of the facies equivalent Macumber Formation (Schenk, 1967). While drilling one of these holes, No. 3-78, oil scum was intermittently detected on the drilling mud. The hole was abandoned at 191 m in anhydrite, without having reached the basal limestone."

Jan 1, 1985

By Paul Johnston

or is it? Mining Automated Loader Technology Application ? Intelligent software mounted in hardware on a remotely controlled scoop. ? Led by INCO, Sudbury, with ? C-CORE, St. John?s ? Automated Mining Systems, Aurora ? Bell Canada, Sudbury ? Laurentian University, Sudbury ? University of Western Ontario, London Completed: March 2000

May 1, 2008

By John E. Udd

"In this paper the author presents the results of the 1992 CIM survey of graduates in minerals and technology programs in Canadian post-secondary institutions. As usual, the trends are out-of phase with the economic state of the industry. People who chose a minerals career in the prosperous days of the late 1980sare now entering a labour market in recession.The cyclical nature of enrollments is illustrated in a series of figures showing the trends since the CIM survey Wa5 begun in 1956 (and even earlier for mining engineering).In the survey, the respondents were asked to provide comments on their perceptions of the problems specific to minerals education in Canada. The large number of responses have led the author to the conclusions and recommendations given in the final part of the paper."

Jan 1, 1993

By J. Wild, M. Ounpuu, G. Chevalier

"The requirements for a finer grind at Heath Steele have resulted in the investigation of agitated milling as a cost effective alternative to conventional tumbling ball mills.The grinding unit is a vertically agitated, or stirred ball mill. Grinding occurs as the result of the motion of a single vertical rotor equipped with protruding pins which impart a stirring action to the ball charge. A comparative evaluation of a 30 kW SALA Agitated Mill (SAM), and a 1.5 m x 2.5 m copper-lead regrind ball mill has been conducted at Heath Steele.An overview of agitated milling as it applies to the reduction of sulphide ore will be the primary topic for discussion. Specific parameters including energy efficiency, media consumption, operating costs, and the mechanical aspects of the SAM operation will be presented.Evaluation of the agitated mill has shown that improved grinding performance at much lower work indices than those of the conventional ball mill is possible. Media consumption has proven to be comparable on an average g/kWh basis, but the mechanical availability of the mill has been low.INTRODUCTIONConventional tumbling ball mill grinding has proven to be an energy inefficient process. Energy losses occurring within the ball mill itself can be attributed to particle friction without breakage, kinetic and potential energy losses, plastic and elastic deformation and the production of heat and sound (Lynch, 1977). It can be generally stated that a certain amount of the input energy will be converted to another form as a necessary by-product of particle breakage. Theoretical interpretation of experimental results indicate that the energy required for breaking the ore particles in a ball mill varies between I% and 25% of the total energy input (SME, 1985)."

Jan 1, 1993

By Y. Hou, E. Arinaitwe, L. Tong

A series of dense medium separation (DMS) tests were performed on four low-grade copper ores from Mount Polley mine in order to determine their amenability to pre-concentration. The tested ores contained disseminated sulphides, mostly chalcopyrite with low copper grades (0.15% - 0.2%) and relatively high iron grades (4.76% - 5.63%). The samples were screened into different size fractions ranging from 9.5 mm to 50.8 mm and DMS tests were performed on each size fraction at various separation densities. The pre-concentration efficiency at different size fractions and separation densities was evaluated in terms of metal upgrading and distribution. Mineralogical tests were also performed on selected DMS sink and float samples in order to understand the influence of mineralogy on the pre-concentration efficiency. The results showed that significant copper upgrading was achieved for intermediate size fractions only at the highest separation density tested. The copper recoveries generally increased with particle size at all separation densities. However, it was impossible to upgrade the copper content in the ores and achieve acceptable recoveries and mass rejections at the same time. Copper recoveries and grades showed a strong correlation with iron recoveries and grades indicating that it is possible to pre-concentrate copper by recovering magnetite and other iron-containing minerals in the ore. Overall, the results suggest that the optimum separation density and pre-concentration efficiency is a function of particle size, and that the ore mineralization properties limit the performance of DMS as a pre-concentration technology for such low-grade disseminated ores.

Jan 1, 2014

By Giles St. Pierre

"The purpose of this paper is to report in a general way on the use of the Portaspec X Ray Spectrograph.At Manitou Barvue, we are milling two types of ores, copper and zinc. The control assay practice was to take grab samples at 4 hour intervals. These samples were dried in the mill, then taken over to the Assay Office where two operators would process them. Three hours later results were available at almost the same time as the operator was ready to take his set of grabs again, leaving no time for adjustments, if any were needed.After a reduction of personnel, there were no assays available on night shift. This practice was slow and inadequate, and a new way of doing control assays was investigated.After investigation the Portaspec was found suitable for the type of operation that we had in mind. The Portaspec is a conventional dispersive type of X Ray spectrograph. The instrument consists of three parts:The Power Supply The Spectrographic Head The Digital ScalerIn our case, where dried powder samples are analyzed, the instrument was provided with a two sample holder using one for the standard and the other for the sample. The operation of the instrment does not require any degree of skill or knowledge of chemistry or spectrography.Previous to buying the instrument, six sets of six to ten samples were sent to the supplier along with the assay for each sample. These samples were Cu. HDS., Cu. Conc., Cu. tls, - Zn. HDS., Zn. Conc., Zn. tls. A definite pattern was observed. For example - six Cu. HDS. samples ranging from .40 to .90 gave 10400 counts for the lowest to 16.040 counts for the highest. The number of counts were then plotted to give percentages."

Jan 1, 1971

By K. Wongpreedee

Recovery and recrystallization of Au wire can degrade strength and alter conductivity properties during exposure to elevated temperature. Au Deformation Processed Metal Metal Composites (Au DMMC's) are being developed for electronic applications requiring high conductivity and high strength. This paper discusses the relationships between microstructure, strength, and resistivity of Au DMMC's. It also presents the results of a recent study on the elevated temperature stability of Au DMMC's of several compositions. Au-7 vol %Ag, Au-14 vol %Ag, and Au-vol 7%Pt DMMC samples were prepared by a powder metallurgy technique. All specimens were processed into wire by extrusion, swaging, and drawing. The smallest final diameter of these wires was 120 ?m. Thermal stability was analyzed by electrical resistivity measurements to determine the relation between transformation rates and time at elevated temperature. The extensive deformation used to produce these composites reshaped the initially equi-axed powder into filaments that are 30 to 100 nm in diameter and 16 to 180 mm in length. The small filament diameter confers high strength on the composite. The high conductivity can be explained by electrons flowing parallel to the filamentary microstructure aligned with the wire axis. Using the Avrami and Arrhenius equation relationships, it is possible to predict the times and temperatures needed to achieve various degrees of homogenization. The Au DMMC's were found to have good thermal stability compared to conventional coldworked Au interconnection wires. Although these composites will revert to solid solutions if exposed to high temperatures for prolonged time periods, their relative stability is sufficient to allow them to maintain their twophase microstructure during the anticipated lifetime temperature profiles of many products.

Oct 1, 2003

By R. Noriega, M. Suazo, V. Murariu

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012