Search Documents

By John E. Udd

I N Part I of this paper, Professor Morrison suggested that our technique of causing cracks to develop around openings in a sheet of photoe1ashc plastic is, in effect, a laboratory-scale rockburst. Our investigations have indicated that the location and direction of these cracks are predictable, and that their growth can be controlled. On several occasions, we have been able to cause these cracks to propagate sufficiently slowly to be followed, with the naked eye. In practice, the rate of growth, gradual or sudden, would depend upon rock properties. This part of the paper presents an analysis of the stresses surrounding the openings before and after failure and also this author's views on the causes and after-effects of cracking. An attempt is made to correlate the stress patterns with those deter-mined from pure mathematics. Considering that the openings, except for the central enlargement, are long apertures with somewhat rounded corners, they might be compared with elongated ellipses having axes ratios of about 20:1 or with

Jan 1, 1963

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By G. Song

This paper reports the anodizing voltage, gas evolution and sparking behaviors of an anodized coating formed on AZ91D in a silicate containing solution. According to their responses to an anodizing current, a four-stage anodizing mechanism is proposed. At the same time, the formed coating is characterized in terms of its microstructure, composition, thickness and corrosion performance. It was found that deposition of MgSiO3, Mg(OH)2 and MgO as well as dehydration of Mg(OH)2 are involved in the anodising process; the vigorous gas evolution accompanied by intensive sparking and the corresponding negative anodising efficiency in the later stage of the anodising process are closely associated with thermal decomposition of water due to the high temperature resulting from the intense sparking on the surface of the anodized alloy; the thickness, porosity, and composition of the anodised coating on a magnesium alloy depend on the final anodising cell voltage; and the corrosion resistance of a thick but porous coating containing more silicates appears to be more corrosion resistant than a thin but compact coating containing less silicates.

Jan 1, 2006

By H. C. W. Bosman

"Over the past five years, contributions from geologists and mining engineers were instrumental in the successful development of MEPS. It is a system of FORTRAN programs specifically designed to be used by mining personnel to solve geological and mining problems. MEPS is a flexible keyword-driven system. Extensive error editing procedures significantly reduce the time required to proceed from problem recognition to solution. Possibly the most attractive feature of MEPS is that computer solutions may be guided or selectively modified to obtain desired solutions. Some highlights of MEPS are:1. Vocabulary that is familiar to mining people.2. Geological data storage and retrieval.3. Statistical analysis and variograms.4. Contour maps of assays and geological horizons.5. Trend surface analysis with residual evaluation.6. Ore reserve calculations.7. Open-pit mine design.8. Marginal profitability calculations on pit walls.9. Production scheduling.10. Vertical cross-section plots indicating pit outlines, ore grade contours and selected geological horizons."

Jan 1, 1973

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By A. S. Romaniuk

More than a decade ago, CANMET management recognized the need to make better use of existing technological information in mining and extractive metallurgy-two fields basic to the economic well-being of Canada. There were at that time no indexes or files dedicated to disseminating technical information for the many minerals mined and processed in Canada, including coal. CANMET, with the nation's largest research and library resources in the minerals field, was in a unique position to fill this need. Initial efforts were concentrated on building a mining file, beginning with identification of world sources of published information, development of a special thesaurus of terms for language control and adoption of a manual indexing/retrieval system. By early 1973, this file held 8,300 references, with source, abstract and keywords given for each reference. In mid-1973, operations were computerized. Software for indexing and retrieval by batch mode was written by CANMET staff to utilize the hardware facilities of EMR's Computer Science Centre. The resulting MINTEC file-one of the few files of technological information produced in Canada-is the basis for the national literature search service in mining offered by CANMET. Attention is now focussed on building a sister-file in extractive metallurgy using the system already developed. Published information sources have been identified and a thesaurus of terms is being compiled and tested. The software developed for CANMET's file-building operations has several features, including the selective dissemination of information and production from magnetic tape of photo ready copy for publication, as in a bi-monthly abstracts journal.

Jan 1, 1979

By J. G. Patterson

"The depressive action of sodium cyanide on chalcocite has been investigated and found to be unstable. Flotation results show that with the addition of sodium cyanide to the system chalcocite is initially depressed but rapidly recovers with time, provided there is sufficient oxygen present.lt is proposed that the unstable depression is due to the reaction of cyanide with adsorbed xanthate and copper ions at the chalcocite surface to form soluble copper complexes. When all the free cyanide has so reacted, xanthate anions can then re-adsorb on the chalcocite surface and the flotation will recover. Results are presented to verify the the above mechanism."

Jan 1, 1968

By Edward I. Renouard

"THE mineral industry is constantly undergoing changes and facing challenges, and today we are in the midst of another serious one -namely, manpower requirement at every level in the mines, shops and plants. In the not too distant past we had a situation where labour was plentiful, although the equipment, by present-day standards, was quite inadequate, and that's easily understandable when you look back at the primitive methods by which our Western mines were first developed and operated, and then improved by the inventiveness and ingenuity of man.I'd like to show you a few slides from drawings made by Buck O'-Donnell which illustrate some of yesterday's methods of mining. Some of you probably had first-hand experience with some of these so you know they were tedious, time-consuming and involved a lot of heavy labour.Taking the Anaconda Company operations at Butte as an example, we can see what has happened in just the past ten years. In August of 1956, the Butte mines had 5,516 day's-pay employees and 976 salaried employees, for a total payroll of 6,492. In August of this year, there were 3,645 day's-pay employees and 605 on the salaried roll, for a total of 4,250. The number of contract miners had gone from 1,347 in 1956 to 606 in 1966 and that of other underground miners from 2,893 ten years ago to 1,149 this year. Along with these changes, however, another change of special significance has taken place, and that is in the number of skilled craftsmen, surface engineers and so on required for our operations. In 1966, we had 1,890 of these people, 600 more than in 1956 and nearly three times as many as just twenty years ago."

Jan 1, 1967

By F. Y. Grepe

"THE MOST common type of mine hoist is, as is very well known, that in which the a.c. wound rotor motor is the driving medium. The reasons for the use of the wound rotor motor are, of course, economic. This type of equipment has, during the years, proved to be very reliable and reasonably satisfactory. It is, in fact, still being installed and in some places where a very hard and exacting duty cycle is demanded. As an example, a 600 h.p. 2,300-volt job was recently installed at the Caledonia mine (1) at Glace Bay. This is a vertical. hoist in a shaft only 175 feet deep but it is, nevertheless, working hard bringing coal to the surface and in making a trip at a speed somewhat better than every 20 seconds.The control equipment for such installations usually consists of a pair of primary reversing contactors which are interlocked both mechanically and electrically, together with some form of secondary controller. This, in the case of small hoists, can be a drum controller and metallic resistors or, in the case of larger hoists, a magnetic contactor panel and metallic resistors or, alternatively, can be one of the various forms of liquid rheostats which are available. The liquid rheostats, if of the dipper type, may be manually operated or it may be operated by some form of servo motor mechanism. In the weir type of liquid controller, the electrolite is, of course, pumped in and out of the rheostat."

Jan 1, 1954

By Dennis E. Bell

"This paper describes exploration and development to 1982 in the southern half of the northeastern British Columbia (Peace River or Northeast Block) inner foothills metallurgical coal belt. Gates Formation, Fort St. John Group, is the primary target; Gething Formation, Bullhead Group, is secondary. This part of the belt remains wilderness when compared to its other parts. Practical formational and structural mapping is described. A local problem known as the Secus Mountain or Mount Belcourt conglomerates is discussed. The three major explorers have been Denison Mines, PetroCanada, and Crows Nest Resources, all with partners. Initial mine construction and rail spur construction are continuing. The new town of Tumbler Ridge is being built. Introduction This paper describes exploration and development to 1982 in the southern half of the northeast British Columbia metallurgical coal belt. The area (Fig. 1) trends 120 km northwest from the Alberta border to the Wolverine River and Bullmoose Creek. The belt averages 15 km in width, and is 20 km at its widest. Physiographically, the area is dominated by rugged inner foothills, with relief to 1,500 m. The trend of the structures is transected by a dozen rivers flowing southwest to northeast away from the Continental Divide. The Rockies, lying immediately to the west, control the climate. One fact continues to colour all coal work in the area. When compared to the other parts of the western Canadian foothills and Rockies coking belt, it remains the least accessible and least mapped portion. Lack of access also makes all work expensive. Current activity centres about two mines in construction at the northwestern end of the area. Denison Mines and partners are developing their Quintette project, and Teck Corporation and partners are developing their Bullmoose project. PetroCanada and partners have intensively explored their Monkman-Duke Mounta,in project, but mine construction awaits better economic times. The rest of the area remains lightly explored, with the exception of some intensive work on particular structures by Denison and Petro-Canada. The focus of coal work has been metallurgical bituminous coal seams contained primarily in the Gates Formation (Fig. 2) and secondarily in the Gething Formation. These formations are found in generally en-echelon structures ranging to several kilometres in width."

Jan 1, 1985

By A. Bauer

This paper describes the trends in recent years in explosives formulated to produce larger blast-hole spacings and over-all lower drilling and blasting costs in hard formations. A consideration of current rotary drilling costs per ft of hole and per ton of muck versus hole diameter indicates that it is now possible that we shall see much further use of lower-energy-content, lower-cost slurries and dry mixes, and larger-diameter and, in many instances, cheaper blast holes. These will be drilled on current or slightly larger blast patterns to yield the same energy input per ton of rock and similar fragmentation at lower costs.

Jan 1, 1968

By W. A. Bell

The Carboniferous system of rocks in the Maritime Provinces include as workable mineral and organic substances, gypsum, anhydrite, salt, coal, building stones, grindstones, limestones, brick-clay shales, fire-clay shales, oil shales, etc. The system is, therefore, pre-eminently of economic value to the provinces in which it occurs, and the more knowledge we may gain concerning it, the more we may be prepared to aid in the development of these useful substances. For this purpose it is not sufficient to state that the ground upon which we stand is underlain by Carboniferous rocks. In-discriminate digging or drilling will not open many new mines of wealth, however difficult it may be to dampen the optimism of gamblers. For mineral wealth has not been scattered in the rocks haphazard, now here, now there, but its distribution has been the result of natural earth forces acting at intervals throughout the countless millions of years that have elapsed since our planet was born. As regards the majority of metalliferous deposits, the earth forces involved have resulted in the penetration of surface or sub-surface rocks by molten rock-matter and associated mineral solutions from deep-seated sources. But the economic Carboniferous deposits that have been mentioned are themselves types of bedded surface rocks rather than immigrant deposits, and their formation and geological history is closely related to that of the rocks with which they are interbedded.

Jan 1, 1924

By Nelson C. White

This paper summarizes the present state and future prospects of the potash industry, with special reference to its impact on production in Saskatchewan.

Jan 1, 1968

Research, whether applied or fundamental, is a human endeavour which increases our understanding of nature. It is insufficient to simply observe, explore, record and classify. It i necessary, as well, to fit the observations into a satisfying theoretical scheme; that is, to synthesize. Two examples of successful research programs in physical metallurgy are di cussed from this point of view. A pessimistic view is taken of the prospects for rapid growth of research activities in the Canadian metallurgical industry. THE term "research" is used indiscriminately to describe any intellectual or experimental activity which leads to a change in society. Proponents of various activities, ex-tending all the way from alloy development to subliminal advertising, use the status of the term for special advantage. With the Canadian Government entering upon a project of support to industrial research, it might be well to determine what definition is most in the public interest. As an academic, I have a rather jealous attachment to the definition that research, whether applied or fundamental, is a human endeavour which increases our understanding of nature.

Jan 1, 1963

By M. Mohan Rao

A Sievert ' technique was used. The few determinations made on 10 per cent and 20 per cent V alloys did not show any deviations from Sieverts' law up to I>N2 = 1 atmosphere. The same held true for alloys of 0.2 per cent Ti. Nitrogen absorptions in Fe-Ti alloys, containing from 0.50 to 0.77 per cent Ti at 1,600°C, follow Sieverts' law at low PN2 values, but, due to the formation of a delta titanium nitride phase, deviate from this law beyond critical values of PN2? There is evidence that this phase is Ti1.1N. The behavior observed can be described by the followmg equations: Ti,.,N(o) = 1.7Ti + N K = (fT; ? % Ti)1?7 (f;;.? %~_) = 0.0020 K = fN. %~ = 0.042 '\)-:>N 2 I NTRODUCTJON Nitrogen's solubility in liquid iron-vanadium alloys was investi-gated briefly by Brick and Creevy ( 1), and more extensively by Kash-yap and Parlee (2) and by Pahlke and Elliott (7). Nitrogen's solubility in liquid iron-titanium alloys

Jan 1, 1963

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

In April, 1961, a large pillar was removed by blasthole mining methods at Inco's Murray mine. More than half a million pounds of explosives were used to break 2,120,000 tons of ore in a single underground blast. The 5, 10 2-inch boreholes, involving 435,815 feet of drilling, were loaded over a three-week period, using conventional explosives and short-period electric caps. From this blast, more than half a million tons of ore have been removed to date (April, 1962) through slusher trenches situated in the footwall of the ore body. T HE Ontario Division of The International Nickel Company of Canada, Limited, operates six underground mines and two open pits in the Sudbury district in the north-central part of the Province. This paper describes the removal of a large pillar at the Murray mine (Figure 1), where 2,120,000 tons of ore were broken in a single underground blast by the blasthole mining method. This is the largest underground blast achieved to date (April, 1962) at Inco mines.

Jan 1, 1963

By V. I. Lakshmanan, R. Roy

"Zinc is the fourth most widely used metal in the world after iron, aluminum and copper. The primary zinc production is through flotation of zinc concentrate, roasting, leaching and electrowinning. Close to 60% of the metal produced is consumed in galvanizing the steel by making a thin layer of zinc coating on the steel surface by hot dip galvanizing. Process Research ORTECH Inc. has developed an efficient energy-saving sustainable technology for the recovery of zinc from secondary sources such as galvanized steel scrap, dross, dusts etc. The process consists of treating the zinc containing scrap in an alkaline solution to remove the zinc and thereby producing a zinc free steel scrap for recycle. The zinc containing leach liquor is subjected to a solvent extraction process to recover value added zinc oxide as the final product. In this paper, important industrial processes for the recycling of zinc including the PRO process will be discussed. BACKGROUNDZinc is the fourth most widely used metal in the world after iron, aluminum and copper. Global refined zinc output increased by 2.7 per cent to 13.16 million tonnes in 2011 and is expected to increase by an additional 2.4 per cent to 13.48 million tonnes in 2012 [1]. The primary zinc production is through flotation of zinc concentrate, roasting, leaching and electrowinning. Close to 60% of the metal produced is consumed in galvanizing steel by making a thin layer of zinc coating on the steel surface by hot dip galvanizing. Other major usages of zinc are in the production of brass and bronze, die casting and zinc-air batteries. The additional demand for zinc could come from its addition to fertilizers to increase crop yield.While the demand for zinc is increasing, many mines are scheduled to close in near future after being depleted of ore. The mines set to close between now and 2015 are Teck Resources’ Red Dog Mine in Alaska, Minmetals’ Century Mine in Australia and Vedanta Resource’s Skorpion Mine in Namibia [1]. The depletion of resources due to continued use and exploitation is becoming a great concern for the zinc industry. As a result, the sustainability of natural resources for continued societal care has become extremely important. Resource conservation and recovery by recycling with minimal environmental impact is a key element for sustainable development. In this paper, important industrial processes for the recycling of zinc including the PRO process are presented."

Jan 1, 2012

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he's hurt. Maybe he's not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

May 1, 2010