Search Documents

By Ellis Thomson

The microscope is now used extensively not only in the examination of solid ore but also in the determination of fragmental mill products. It has therefore become a matter of paramount importance to be able to mount and polish fragmental as well as solid specimens in the easiest and most efficient way, so that the minerals present may be readily determined. In the case of the solid ore the ordinary mount of plasticine set on a glass or metal slide serves for most practical purposes. An improvement on this is furnished by the small brass container inside of which the specimen is mounted in a cementing medium of sealing wax. The latter is the method in use at Harvard University. It has the advantage of uniform height, thus obviating the necessity of a slide of any sort. It is also easily catalogued as the brass holder may be stamped with a convenient series of letters and numbers that will serve as a label. Other advantages of this type are the ease with which any particular part of the section may be re-located, the excellent storing facilities afforded by mounts of uniform size, and the possibility of polishing ten or a dozen sections at the same time by means of a holder which is placed over the polishing wheel, is geared with it, but revolves the opposite way.

Jan 1, 1926

By I. A. Menshikh, S. A. Kotov, N. L. Shinkarkin

All the cycle for conversion of natural and reprocessed uranium of ROSATOM’s “TVEL” Fuel Company is concentrated at the Siberian Chemical Plant. Conversion capacities are located on two sites, i.e. the Radiochemical Plant, which refines feedstock, and the Conversion Plant, which produces uranium oxides and uranium hexafluoride. Liquid radioactive waste arising in the process, after pretreatment, is transferred to a dedicated national operator for underground disposal. Environmental strategies pursued by the Fuel Company involve the introduction of process solutions intended to eliminate liquid radioactive waste and convert it into a solid phase. In the 5–7 years coming, work will be performed to refurbish and upgrade conversion facilities of the Siberian Chemical Plant that will principally change its radioactive waste management scheme. This paper describes the current waste management scheme and sets out planned schemes for management of natural and reprocessed uranium waste, which will be implemented in the refurbishment of conversion facilities of the Siberian Chemical Plant. The new technologies for the management of liquid radioactive waste from uranium conversion described in the present paper have an undeniable advantage over the current technology mainly due to significantly less environmental harm.

Jan 1, 2020

By S. Mohammadnejad, M. Olizadeh, B. Mehrabi

A new method using a combination of comprehensive mineralogical and analytical approach which includes optical and electrical microscopy and several analytical techniques with diagnostic leaching has been used to characterize the associations and distribution of gold in a variety of minerals from the Zarshuran refractory gold ore, NW Iran. Zarshuran ore with an average of 7.9 g/t Au-grade and about 8% arsenic with gold recovery less than 20% in direct cyanidation is considered as high arsenic, high au-grade refractory gold ore. In most of the refractory ores, gold is associated with arsenopyrite and co-para genetic ore minerals, while in Zarshuran ore; gold is associated with orpiment, realgar and arsenian-pyrite. Considering its mineralogy and As content, it can be considered as the most difficult refractory ore for characterization and processing. Results from the mineralogical examination and diagnostic leaches indicate that there is only a small amount of free gold (17-19%) that is present in cyanide-soluble sulfo-arsenides compounds, predominantly orpiment and realgar. Diagnostic leaches also indicate that little gold is occluded within the silicate structure (14%). Overall, the gold is mostly included in sulfides, arsenic sulfides and sulfo-arsenides (50%). The results also have shown how the technique can be used to gain a good initial understanding of potential metallurgical problems for a refractory gold ore.

Jan 1, 2005

By H. Salamanca

Recently, the mining industry has become one of the leading target markets for the technology industry as they need to innovate in their productive processes in order to boost productivity, reduce operation costs, increase operation safety, and improve the quality of life of their workers. This work presents the technological developments that HighService has done in different stages of the mining productive processes to include robotic manipulators in their automation solutions as well as the development of new equipment and sensors. The robotic technology integration is presented in different applications such as handling and selection of cathodes in E-W machines, automation of base plate maintenance, automation of cathode stripping machine, and multi-tools handler for liner bolt replacement in SAG mill liner maintenance activities. The proposed solutions show technical and economical viability with low initial investment and short implementation period of six (6) to ten (10) months. The results have been validated in plant, obtaining higher production rates and availability.

Jan 1, 2007

By R. N. W. DiLabio

"In a continuing program of mapping glacial dispersal trains, near-surface till samples were collected down-ice from a copper-silver-gold prospect at Onaman River, Ontario, and down-ice from the past-producing gold district at Oldham, Nova Scotia. The program is designed to aid exploration by illustrating glacial dispersal from various types of known occurrences and by identifying postglacial processes that control drift composition at a detailed scale.Native gold was mined at Oldham from arsenopyrite-bearing saddle reef quartz veins in a dome in Early Paleozoic slates of the Meguma Group. Gold abundances greater than 10 ppb in till form a dispersal train at least 1900 m long. Gold abundances between 40 and 100 ppb occur in clusters up to 600 m down-ice from gold-bearing bedrock. Anomalous arsenic abundances in till form a broad train 1100 m long that is significantly different in shape from the gold train.At Onaman River, subeconomic amounts of Cu-Ag-Au occur in quartz lenses in Archean mafic volcanic rocks. A dispersal train defined by the distribution of mineralized boulders and increased abundances of Cu, Ag and Zn in till extends 600 m down-ice from mineralized bedrock. Gold abundances between 10 and 70 ppb do not define this dispersal train, but occur instead in clusters 300 to 600 m down-ice from mineralized bedrock. In vertical sections in the upper 2 m of copper-rich till, Au abundances vary sympathetically with Ag and Cu levels; however, there seems to be no preferential site of Au enrichment in the mineral portion of the soil profile.Several of the mineralized boulders at Onaman River are richer in Au and Ag than the mineralized bedrock from which they were derived. Although some of the high Au and Ag assays were caused by biased sampling of sulphide-rich portions of the boulders, many were caused by leaching of sulphide minerals from 'the boulders, which left a limonitic boxwork that is enriched in Au and Ag. A few of the Au-rich boulders may have been derived from an unknown bedrock source."

Jan 1, 1982

By H. Arima, Y. Kudo

In general, the iron content of zinc leach residue produced by sulphuric acid leaching from calcine is disposed as jarosite or goethite into a tailing dam. More recently, these iron residues have been treated pyrometallurgically to avoid waste disposal. The Iijima refinery selected a different zinc leach residue treatment process for iron control when it was established in 1971. The Iijima refinery is the only plant in the world that has processed a zinc leach residue by the combination of SO2 pressure leaching and O2 pressure hematite precipitation. The process enhances zinc recovery and recovers gold, silver, copper, lead and rare metals in saleable by-products. This paper focuses on the two stages of autoclave application in the zinc leach residue treatment process. The detailed flowsheet and recent advancements to improve the quality of by-products are discussed.

Jan 1, 2004

By Frank Martonhegyi

"The objective of this paper is to review the coal basins in the Canadian part of the Western Cordillera to aid their understanding, and to aid in finding and proving places of economic coal mining potential. Coal occurs in eugeosynclinal basins in the Western Cordillera which evolved through three stages: -from systems of volcanic arcs in the Late Jurassic to mid-Cretaceous; -through an intermediate stage with deposition in increasingly restricted successor basins in Jurassic to Early Tertiary; -to a continental stage by the Eocene. Minor coal seams occur usually in late volcanic arc stage sediments bur they can be locally thick as they are on Queen Charlotte Islands. Successor basins usually show a marine-paralic-limnic evolurion. Signijicanr coal deposits occur in the tarter two sequences in the Whirehorse (Tantalus) and Bowser (SkeenaSusrur) basins. Currenr activities are intensive in the more accessible Bowser Basin, for example at Telkwa, Susrut River and on the Groundhog coal field. On Vancouver Island major coal seams occur in cyclic sediments, but the more accessible deposits are mined our. Exploration renewed recently in the less accessible northern part of the Island, for example Quinsam, for surface mineable coal. The Western Cordillera is a mosaic of allochtonous tectonic blocks. They originated from the south and were displaced northward by several hundred kilometres. Many Tertiary coal basins are related to strikeslip transcurrent faults along which the later part of displacement took place, for example the Dawson coal area in the Tintina Trench. Tensional and dipslip normal faulting also created or enhanced sites for thick peat accumulation. For example at Hat Creek 280 m of coal occur in a 550 m section. Secondary structures are often better exploration targets than the main fault zones. Pluvial and alluvial fan environments away from the main drainage are usually the favourable sites for thicker and cleaner coal deposition."

Jan 1, 1985

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By D. Virely, M. Gasc-Barbier, J. Guittard

"The valleys of the Dordogne and the Vézère (France) have been inhabited since prehistoric times, as evidenced by the famous site of Lascaux. A few miles away, the village of La Roque-Gageac is also a very popular tourist destination (about 1.5 million tourists per year): The village is sandwiched between a massive limestone cliff and the Dordogne river. The collapse of a cave roof high above the village in January 2010 led us to characterize instability together for the cave and the whole cliff and propose a adapted instrumentation to monitor the fracture openings in the rock mass that are linked to climatic variations. Measurements have been going on and been recorded for nearly 4 years. They point out the role of thermal stress fatigue in the breakdown of the rock mass. In this paper we describe the site under study, the instrumentation and its main results. INTRODUCTIONThe phenomenon of thermal fatigue has been very little studied as far as rocks are concerned, whereas it is rather well characterized for other types of materials: Elsevier published a journal dedicated to fatigue (International Journal of fatigue). In the case of rocks, thermal phenomena and their impacts on mechanical behavior have been analyzed from a micro-structural point of view, and it is now well-known that an increase in temperature causes a dilatation of crystals (Arnould et al., 2004; Berest & Weber, 1998). This dilatation may lead to the development of inter-granular traction and compression stresses, and if those stresses are greater than fracture strength, inter-granular and intra-granular cracks may take place. On the other hand, the fatigue phenomenon (cyclic repetition of a temperature variation which is less extreme than the one that may lead to this inter-granular or intra-granular fracture) is a phenomenon which has not been much studied.The principal studies on thermal fatigue on rocks come mainly from the field of geomorphology, particularly in connection with the analysis of the evolutions of past climate that can explain the present shapes of those landforms: those studies remained essentially qualitative and not quantitative. Le Ber & Oter Duthoit (1987) proposed a thermal and thermodynamic approach to analyse the disaggregation of rock masses. This analysis is dedicated to the study of paleoclimates and was implemented to better understand the formation of slope deposits in order to propose transfer models permitting the reconstruction of the climactic conditions contemporary to their appearance. Since deterioration in the cliff only appears after several cycles, it means that it is a gradual and irreversible deterioration which leads to an increase of the « disorder ». Seen from a macroscopic system point of view, this irreversible evolution is quantified by the internal creation of entropy."

Jan 1, 2015

By K. Yoshida

Recently, light magnesium alloy with superior heat radiating ability has been attracting attention in various fields. However cold plastic working of the alloy is very difficult and hot working necessary. Furthermore, the magnesium of products with complicated shapes is difficult, the processing cost is high, and the applicability of the alloy is limited. In this study, a technique for obtaining fine wires and tubes by cold drawing is examined to obtain wires and tubes with high strength, quality and surface morphology, while decreasing production cost. In addition, the shearing strain of magnesium alloy wires and tubes drawn under various drawing conditions was calculated by FEM analysis. It was clarified that cold drawing of magnesium alloy is possible. It was also demonstrated that greater reduction of the cross-sectional area could be realized during cold wire and tube drawing by optimizing the drawing conditions.

Jan 1, 2006

By V. G. c Papangelakis, M. Huang

A conductivity cell, developed previously, was employed in an effort to investigate the inter-relation between electrical conductivity and acidity of sulphuric acid - metal sulphate solutions at high temperatures. The measured solutions include the H2SO4-H2O, MgSO4-H2O, H2SO4-MgSO4-H2O, H2SO4-MgSO4-Al2(SO4)3-H2O solutions. All solutions reported in this paper were measured from 15 to 250 °C at equilibrium vapour pressure. The maximum measured concentrations of H2SO4, MgSO4 and Al2(SO4)3 were 0.45 m, 0.30 m and 0.10 m, respectively. It was found that, from 15 to 250°C, there is a linear relationship between H2SO4 concentration and electrical conductivities for acid concentration up to 0.45 m. At 250 °C and constant H2SO4 concentration, the solution conductivity drops with the increase of MgSO4 concentration. Lt is suggested that this drop is caused by a decrease in the concentration of H. Finally, an empirical model was developed based on the available measurements. This model has been tested against real laterite leach solutions where sulphuric acid and metal sulphates are dominant electrolytes. The average difference between the estimate acid concentration from this model and the one from titration was less than 5%.

Jan 1, 2004

By Christopher R. Lattanzi

"Discounted cash flow analysis provides a means of relating the magnitude of expected future cash profits to the magnitude of the initial cash investment required to purchase an asset or to develop it for commercial production. The objectives of discounted cash flow analysis are to determine:.. The net present value of a stream of expected future cash revenues and expenditures... The rate of return which the expected future cash flows will yield on a given level of initial cash investment.In the case of mineral properties, discounted cash flow analysis is generally accepted as the preferred method of valuation, whenever sufficient data are available to permit its reasoned application. Sufficient data are required to support estimation of all of the individual elements of cash revenue and cash expenditure which will be associated with the development and operation of the property, up to the end of its estimated life. It is the accuracy of these input estimates which determines the validity of the resulting determinations of profitability and rate of return on invested capital.In undertaking any discounted cash flow analysis, it is important to recognize certain fundamental attributes of the mining industty:.. The basis of any mineral development is the existence of an ore reserve... Costs are determined by the number of tonnes mined and processed, while revenues are determined by the number of pounds or ounces of metal produced. The two are related by the recovered grade of the ore... Profit is typically more sensitive to changes in revenue than it is to changes in cost... Commodity price is a principal determinant of revenue, but it is also the factor with which is associated the greatest level of financial risk.In the end, of all of the factors which must be considered in the discounted cash flow valuation of a mineral property, the most significant are the reliability of the reserve estimate, particularly with respect to recovered grade, the price at which the product is to be sold, and the risk of not maintaining the projected level of price."

Jan 1, 2003

By J. D. Jones

The geographic occurrence of economic mineral deposits presents a variety of problems in modern tailings disposal operations. This paper presents case histories in several sectors of the mineral industry as well as the several stages of operations planning required for new designs, system expansion, reactivation of abandoned systems and upgrading to present environmental standards.

Jan 1, 1978

By N. R. Andrade-Gonzalez

In this paper, the effect of magnesium and strontium additions on the heat treatment behaviour of cast A319,2 alloy was investigated, Permanent mold samples were heat treated at 495 °C for 4 and 24 h, then quenched in hot water and aged at 180 °C and 220 °C for different temperatures, It is found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu alloys, mainly when Mg and Mg-Sr are added, The results of electron probe microanalysis (EPMA) observations reveal that the age-hardening behaviour is related to the precipitation sequence of alloys, For the Al-Si-Cu alloy, the first aging peak is the result of the high-density GP zones, while the subsequent peaks arise from metastable phases, Obvious intervals during the transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks, It is seen that addition of Mg (-0,40 wt %) leads to the precipitation of coarse Al5Mg8SioCu2 particles. When modifying the high Mg alloys, Cu-intermetallics segregate in areas away from the growing Al-Si eutectic regions, Modification with strontium retards the precipitation of the silicon out of the matrix.

Jan 1, 2005

By M. Abdellatif

Successful demonstration of The Mintek Thermal Magnesium Process (MTMP) was achieved in November 2004 at the pilot-scale, About 30 tons of magnesium producing recipe was smelted in the DC arc furnace over a continuous operation of 8-days, Twenty-two furnace batching-tapping operations were carried out at a feed rate of 525kg/h and a smelting temperature of 1600-1700°C, The MgO content in the produced slag was as low as 6,7%, and averaged 9,2% MgO, resulting in an overall magnesium extraction of 77%, which reached 87% during good operating periods, Magnesium vapour was extracted at a rate of 70-85kg/h and was delivered to the condenser that was operated at 680-720°C, The magnesium was captured in the condenser crucible in a liquid state, allowing its prompt tapping, More than 3500kg of crude metal were produced over 15 on-line metal tapping operations, On average, a condensation efficiency of 85% was achieved during the entire testwork, which peaked at 87% during steady operations, The quality of the crude metal was similar to, if not better than, that of the Magnetherm's crude magnesium, A pre-feasibility study has indicated that the MTMP has the potential for lower capital and operating costs as compared to the electrolytic process, and therefore Mintek and its consortium partners are exploring opportunities for a commercial production facility.

Jan 1, 2006

By V. Loya

Metallic foams (MF) are relatively new materials with a combination of attractive properties (permeability, high surface area, thermal and chemical stability, etc,), They can be produced from different materials and can be manufactured using various processes, Due to their unique properties, they find applications in different sectors of engineering, such as energy absorption, filtration, heat dissipation, etc, For many applications, the permeability is an important parameter to characterize and optimize, Most of the recent literature on the subject studied the permeability in the low velocity range. The present study was carried out to have a better understanding of permeability for greater velocity ranges, An equipment was designed and built for this purpose, Pressure drop measurements were made across the thickness of open-cell nickel foams, Pore and window sizes were measured by image analysis on SEM micrographs, The experimental results are in relatively good agreement with the Hazen-Dupuit-Darcy model (R2>98%), The permeability is affected by pore size, porosity and the normalized projected area of the connecting pores (ie. windows).

Jan 1, 2005

By S. Hunt, S. Jayasekera, J. Kyle, N. Perera, K. Stone

A preliminary investigation has been conducted to determine the conditions for the precipitation of phosphate from the liquor produced after a hydrochloric acid pre-leach and rare-earth recovery from a rare earth containing fluorapatite concentrate from the Nolans rare earth deposit in the Northern Territory of Australia. The results show that at 50oC the phosphate can be precipitated in two stages using limestone to produce a Stage 1 precipitate containing most of the impurities including iron (94%), aluminium (92%), fluoride (98%), uranium (84%) and thorium (94%), followed by a relatively pure Stage 2 dicalcium phosphate precipitate (DCP) containing only 0.05% Fe, 0.05% Al, 0.1% F, 0.01% U, and <0.01% Th. The initial Stage 1 precipitate contained about 25% of the phosphate while the remaining 75% reported to the Stage 2 phosphate precipitate. Depending on the required radioactivity specifications, the amount of phosphate in the Stage 1 precipitate could be reduced. Reagent requirements were 11.4 kg limestone (as pure CaCO3) per cubic metre of solution for the Stage 1 precipitate and 39.7 kg limestone (as pure CaCO3) per cubic metre for Stage 2. The analysis of radionuclide balance indicated that radionuclides deported mainly to the final filtrate (86.4%) compared to Stage 1 precipitate (5.4%) and Stage 2 precipitate (8.2%). Settling and pressure filtration tests indicated the precipitates were both readily settled and filtered. The final moisture contents of the Stage 1 and Stage 2 precipitates were 62.5% and 49.3%, respectively.

Jan 1, 2014

By K. Hambrice, E. Fauveau

"When it comes to measuring the level of bulk solids, liquids, and everything in between, guided-wave radar technology now offers more level-detection capabilities than ever before. For an ever-widening range of previously hard-tomeasure products such as molten sulphur, liquid ammonia and petrochemicals, guided-wave radar transmitters provide accurate level measurements even under harsh chemical environments, wide variations in operating temperatures and pressures, and low dielectric constants.Great strides have been achieved in making these units easier to configure to a variety of process applications coupled with the simplicity of integrating these devices with most digital communication protocols. These improvements come as welcome relief to process engineers within an expanded range of level applications across several different industries that seek solutions to measuring the contents of tanks, silos, hoppers, bins, mixing basins, and vessels.Because radar transmitters have no moving parts, radar has already established a dominant niche in level measuring that quickly distances itself from mechanical means, which do not hold up as well in dirty service. Radar achieves its nonmechanical level detection capability by measuring the time of flight of the transmitted signal.Known more accurately as time domain reflectometry (TDR), the process involves sending microwave energy down into a vessel. When the pulse of radar energy reaches the product (indicated by a change in impedance), part of the pulse is reflected back toward the transmitter.A receiver measures the exact duration of time between the transmitted and reflected signal — the “time of flight.” The device analyzes this time and ultimately displays the level of the product as a distance in feet, metres, or other engineering units."

Jan 1, 2003

By J. J. Quinn

Several mineral flotation plants utilize process water with high soluble salt content. The processing of semi-soluble minerals, the use of recycle streams, sea or well water give rise to this situation. It is unclear as to the overall effect on flotation response though there does seem to be evidence of bubble size reduction, increased froth stability and reduced reagent dosage. The present work aims to quantify the effects of salts present in process water on gas dispersion (bubble size and gas holdup) and froth properties. The salts examined were NaCI, CaCl2, Na2SO4, Na2S2O3 and Al2(SO4)3. Tests were conducted to determine the effects of salt type and concentration on gas holdup and bubble size distribution. The salts containing multivalent ions had a greater impact than the monovalent ions, in keeping with the literature. A relationship between gas holdup and ionic strength was established. The concentration of frother (methyl isobutyl carbinol, MIBC) giving equivalent gas holdup was determined. The effect of salt and frother combinations was also explored.Proposed mechanisms for coalescence inhibition in salt solutions are briefly reviewed in light of the current findings.

Jan 1, 2006

By J. Muralha, L. Lamas

"Given the results of triaixial tests, regressions are commonly used to evaluate the parameters of failure criteria that model intact rock strength and to perform statistical inferences used to evaluate characteristic values defined in EC7. Statistical robustness of these inferences is affected if the basic hypothesis underlying regression are not met, namely homoscedasticity (constant variance of the errors). This paper presents analyses of 23 sets of triaxial tests, starting by the evaluation of the regression parameters of the Mohr-Coulomb linear criterion and of the Hoek-Brown non-linear criterion, followed by carrying several statistical tests to check the homoscedasticity null hypothesis of independence between the variance of intact rock strength and the confining stress.INTRODUCTIONThough rock engineering design is clearly included in the scope of Eurocode 7(EN1997-1), its implementation raised a wide discussion regarding the applicability of structural safety concepts to geotechnical design of construction works in or on rock masses. The basis of the limit state design philosophy adopted in EC7 is that, for each particular design situation, all the possible limit states for a structure, or part of it, shall be considered and that it shall be demonstrated that the likelihood of any limit state being exceeded is sufficiently small. Though EC7 allows the limit states to be verified by one or a combination of methods, use of calculations is by far the most used, and it is often confused with the EC7 itself. It involves using characteristic values of actions, ground properties and geometrical data, as well as obtaining their design values by the partial factor method.Characteristic value of a given material property is defined in Eurocode (EN 1990) as: “value of a material or product property having a prescribed probability of not being attained in a hypothetical unlimited test series. This value generally corresponds to a specified fractile of the assumed statistical distribution of the particular property of the material or product”. As regards the design value of a material or product property, according to the Eurocode it is a “value obtained by dividing the characteristic value by a partial factor”."

Jan 1, 2015