Search Documents

By Tim Gartner

This paper introduces a new application of a proven technology to provide dynamic, voltage regulation in underground mine electrical distribution systems. This technology acts to ?stiffen? the electrical power feeding continuous miners and generally raise and improve the voltage regulation at the continuous mining machines which may be located over long cable distances from the mine incoming electrical substation. This is extremely valuable for large underground continuous mining operations that use high power electrical mining machines fed over very long cable lengths (measured in 10s of km, from mine shaft to mine operating face). This new technology provides fast acting dynamic voltage regulation (voltage support) while starting continuous borers and extensible conveyor belts. Additionally, if the mine suffers from a lower distribution voltage due to long cable lengths, this new technology will raise the overall voltage at the mining machine, which can increased mining machine production and lead to longer motor life. The technology is based on voltage source converters operating as static VAR compensators specially packaged for the harsh underground mine environment. While static VAR compensator technology has been successfully used in utility and large industrial applications for many years (including open pit mining and arc furnaces), it has not (until now) been applied in underground mining. The paper will present the problem of poor voltage regulation in underground mines on weak electrical utility networks. It will then discuss some of the alternatives that have been used to resolve this voltage problem. It will then introduce the new technology used to solve the problem and review the issues involved in using this technology in the harsh underground environment. Finally, the paper will present preliminary performance results from an actual installation in a large underground continuous mining operation in Canada.

May 1, 2003

By G. A. Young

THE Geological Survey was created in 1842 to aid the development of Canada's mineral resources. Although the institution has been in existence for nearly 100 years and has accomplished an immense amount of work, the need for its services remains as great as ever and, indeed, it is difficult to imagine a time when the country will no longer require a Geological Survey. This is so because of the tremendous effort required to make an adequate geological examination of so large an area as is embraced by Canada and partly because what today may seem an adequate geological examination proves, later on, to be inadequate. The ultimate objective of the Geological Survey is to complete the study of all phases of the geology of Canada, that is, to determine how and when the physical features originated, how and when the soils and other unconsolidated deposits were formed, and how and when the solid rocks and associated deposits were produced and assumed their present conditions. When the study has been completed, any only then, will it be possible to make a reliable estimate of the country's mineral resources. This appraisal embraces more than determining the value of already discovered deposits: it also involves attempting to establish what kinds of undiscovered deposits may be present and where they may occur. The estimating of the potential mineral wealth can be clone only after the geology of the country is known. Not until then will it be possible to forecast what types of valued deposits may occur in a district and what types will almost certainly be lacking. A thorough knowledge of the geology of the country is desirable not only to permit estimating the potential mineral resources but also as an aid in locating and developing mineral deposits whether these are of the nature of a bed of limestone, a seam of coal, a reservoir of petroleum, a vein, an irregular body of sulphides, or any other type of deposit.

Jan 1, 1940

By S. Eckert, M. Reuter, O. Keplinger, D. Obiso, N. Shevchenko, M. Akashi

We report on laboratory experiments focusing on bubbling phenomena arising from gas injection through a top submerged lance (TSL) in a liquid metal layer. The objective of this study is to reveal the characteristics of the formation and behaviour of the particular bubbles at different gas flow rates and submergence depths of lance. Visualization was performed in the eutectic alloy GaInSn using X-ray radiography. Argon bubbles were injected through the injection positions at three different submergence depths. Essential parameters such as the bubble size, bubble shape, detachment frequency and the two- dimensional gas distribution in the flat vessel were obtained by image processing. The results show that the deep position of the submerged lance causes an asymmetric large-scale circulation inside the fluid vessel. Bubble detachment frequencies were calculated by Fast Fourier Transformation from fluctuations of the image intensity in the vicinity of the nozzle injection point. This frequency does not show strong variations with respect to changes of the gas flow rate and the submergence depth of the nozzle. An increasing gas flow rate results in an increasing two-dimensional projected bubble area and the occurrence of a significant number of small bubbles being trapped by the strong fluid flow in the liquid metal layer. INTRODUCTION The Top Submerged Lance (TSL) process has been an essential component of the metallurgical industry since the emergence of first concepts about 50 years ago (Floyd, 2005). The process, which is characterized by blowing reactive gas through the submerged lance into a liquid bath, was developed mainly for improving the tin smelting process and has been applied for waste treatment or the production of several metals such as copper, lead, nickel and zinc. The productivity of the reactor is determined mainly by the efficiency of the chemical reaction between the gas or solid particles and the liquid. To achieve a high efficiency requires good exchange between the gas-liquid phase and therefore a large interface area. The efficiency changes greatly with the number and size of bubbles injected from the nozzle and the extent of splashing on the free surface. The degree of turbulence in the bath plays a decisive role here. For the reason, the design of an efficient TSL process requires a profound knowledge of the fluid dynamics especially for complex multiphase flows.

Jan 1, 2019

By R. W. Pauls

"Many tens of thousands of hectares of forested land will be disturbed and reclaimed in the surface mineable Athabasca oil sands area during the next few decades. The surface area disturbed by Syncrude’s Mildred Lake development alone exceeds 10 000 ha to date. It is not clear that reforestation of disturbed areas will best accommodate the aspirations of all stakeholders, particularly traditional users of the land. A five-year research program by Syncrude Canada Limited and the Fort McKay First Nations has examined the feasibility of raising bison on land reclaimed after disturbance by oil sands development. Forage productivity and carrying capacity for bison was comparable to that of grasslands elsewhere in Alberta. Concerns regarding compaction of newly rebuilt soil by bison traffic proved unfounded. Bison demonstrated weight gains typical for ranched bison and calving rates averaged 90%, a value typical for ranched bison. The animal husbandry problems encountered were typical of those occurring on bison ranches elsewhere in Alberta. An economic analysis indicates that a 1000 ha bison ranch on reclaimed land has a net present value that compares very favourably with a similar area supporting commercial forest. Subject to approval by Alberta Environmental Protection, the current research project will be expanded as a pilot commercial ranching venture in order to explore its commercial viability as a business venture by the Fort McKay First Nations. At the same time, measures will be implemented to resolve various regulatory issues associated with commercial bison production in the oil sands area.BackgroundSyncrude Canada Ltd. (Syncrude) is proposing, in its land reclamation strategy, a feature that is, depending on one’s background and perspective, regarded as an innovative approach to land reclamation, a threat to the regional forest industry, a creative response to aboriginal stakeholder concerns, a reneging on reclamation commitments, an opportunity to provide an ongoing economic base for postoil sands regional economy, or an environmentally unsound use of the land. These diverse and sometimes strong reactions have been generated by the proposal to introduce bison, either free-ranging or commercial ranched, to the reclaimed landscape."

Jan 1, 1999

By G. Bonin, R. P. Preston

"This paper presents a series of case studies where spherical camera photographs were used to generate 3D shaft models using photogrammetric methods. The shaft models were, checked for accuracy by comparing them to overlapping laser scan data, provided survey data or idealized shaft models. Short lengths of model were found to more accurately reproduce the shaft surface, with a best observed accuracy of 8 mm. Longer models encountered errors with accumulated errors as exhibited by slight deviations from vertical or slightly conical model shape. At present, the models are considered acceptable for general documentation and gross change detection. INTRODUCTION Shaft inspections are required by mining regulations in many jurisdictions and are commonly completed by trained mine personnel via visual inspections. This can be time consuming and prone to errors due to lapses in attention and the rapid travel rate required to inspect an entire shaft in a reasonable amount of time. Similarly, because of the time requirements, there can be impacts on other aspects of mining as a result of occupying the shaft for inspections. Spherical cameras with supplemental light systems offer a modern addition or alternative to conventional inspections. These cameras can be lowered relatively quickly to collect high definition, fully illuminated videos of the shaft that can be reviewed in detail later while the shaft returns to service (Gillis et.al., 2019). The use of cameras offers a further opportunity for valuable survey data generation from the same original data stream. The video data can be processed into three-dimensional (3D) models using Structure-from-Motion (Westoby et al., 2012) based photogrammetric methods. Depending on the quality of the source video and availability of survey control (required for all photogrammetry models) these models can be very accurate. Shaft surveying can be conducted with traditional theodolite methods but such surveys are time consuming and limited in their data density. Similarly, scans can be completed using conventional terrestrial laser scanners, but this requires a significant number of distinct setups to provide sufficient overlap between scans. Work is being conducted both on the laser scanning (SLAM, Durrant-Whyte & Bailey, 2006) and photogrammetry fronts towards kinetic scanning (Benecke, 2017) systems. The major advancement which is permitting these kinetic systems is Inertial Measurement Units (IMUs) which can provide localization in GPS denied environments and reduce errors associated with the open traverse format associated with shaft scanning."

Jan 1, 2019

By Cesar Carrasco

Mine reconciliation is the art and science of comparing predictions and real-world outcomes with the intent of revealing the true quality of performance of models, planning, mining, and mineral processing. When mine reconciliation is conducted in a systematic, transparent and sustainable way it can play a central role in the governance of Mineral Resource and Mineral Reserve (MRMR) estimation and reporting. The core processes of modelling, planning, mining, and processing need to be transparent to be able to demonstrate that MRMR are reliable predictors of mine performance and value. Transparency is also necessary for mine technical staff to generate meaningful analyses, conclusions, and business improvement actions that demonstrably maximise value for all stakeholders. Most mines have some form of mine reconciliation practice, however because there is no agreed industry standard, and because mine reconciliation is difficult for a variety of reasons, it is often unsustained and/or ineffective at delivering the required transparency of performance. To deliver true governance of MRMR and business value, mine reconciliation must be sustainable. There are two categories of issues that combine to make mine reconciliation extremely difficult to sustain, these are technical, and people related. Technical issues include defining standard terms, accurately tracking material flows, data availability/adequacy/quality, calculation of key performance indicators and tolerance limits, analysis, and interpretation of results, understanding limitations of modelling techniques, and defining appropriate actions that can deliver value. These technical challenges are non-trivial, however compounding these are a range of people issues that include personal agendas, scepticism, lack of knowledge and experience, poor teamwork, absent leadership, toxic workplace culture, staff turnover, ineffective communication, siloed organisational structure, and lack of deliberate change management. All these problems can be solved with clarity of purpose, definition of the process of mine reconciliation, discipline in following the process, appropriate resourcing, and commitment to success across the entire organisation. Outlined in this paper is a management system that delivers sustainable mine reconciliation by addressing both the technical and people issues described above. This approach can deliver significant value for a mine and adds a robust, defensible governance over MRMR estimation and reporting.

Oct 1, 2024

By T. G. Joseph, A. Sharma

ABSTRACT: Ultra-class haul trucks operating in oil sand face operational and maintenance issues as a result of soft underfoot conditions (Joseph, 2002). With exposure to frequent high g loading events, tire life is reduced due to sidewall belt fexure and frequent ground contact. Therefore, an improved under-standing of the interaction between tires and oil sand is needed. This paper examines the outcomes of a series of static and cyclic loading tests, performed using a scale tire on rigid, sand, and oil sand surfaces. Geometric predictions are made regarding the footprint area and vertical deformation of an ultra-classtire on similar surfaces.

Jan 1, 2011

By Rebecca L. Jones

The paper addresses the application of XPAC AutoScheduler at the Fort Hills Energy Oil Sands Project to complete fast turn around ?what if? scenario testing of different mine schedules. Traditional scheduling approaches involve engineers making a ?best guess? at the required mining sequence, loading this sequence into a scheduling package and testing the results to determine if the schedule meets corporate objectives. This process is iterative and can be very time consuming. Autoscheduling techniques, on the other hand, are based on the engineer pre defining the mining rules and constraints of the deposit. The software then automatically selects a sequence of mining which the schedule should try and achieve, based off specified corporate objectives. Under this system the engineer is able to adjust the objectives and rules to evaluate numerous scheduling scenarios quickly and easily. An XPAC AutoScheduler model was built, documented, and implemented by Runge and Petro-Canada Oil Sands Inc. personnel in a month. It is currently being used by Petro-Canada Oil Sands Inc. to run multiple schedule scenarios, most taking less than ten minutes configure and ten minutes to schedule. The results of each schedule are tabulated with supporting graphs on; the bitumen grade profile, strip ratio, ore inventories and mined tonnage. In addition to this, the block model may be animated to show the progression of the resources mining the schedules.

May 1, 2008

By T. Crivits, I. Bellemans, K. Verbeken

In the metallurgical industry, furnace cooling is often employed to enhance furnace lifetime. Hence, the pyrometallurgical phase comes in close contact with a non-air coolant. The proximity of the pyrometallurgical phases to the coolants may lead to dangerous situations. In case of a breach of the cooling circuit, the contact between a hot and a cold liquid may cause a vapour explosion. The outcome of this vapour explosion includes a pressure wave which could result in damage to the furnace, bodily injuries or even casualties. To prevent such dramatic events, the origin of vapour explosions is currently being studied in more detail. For this purpose, OpenFOAM was used to perform Computational Fluid Dynamics (CFD) simulations. In a first step, simulations were run to get a better idea of the influence of the compressibility on the simulations. The obtained results help in getting a better insight on the need of computational power, and possible numerical errors using compressible or incompressible solvers in future simulations. In a second step, systems without vapour explosions were simulated and compared to experimental results with mercury and aluminum. INTRODUCTION Humanity started using metals for tools around the Chalcolitic (~7400 cal BC), when copper was melted in small furnaces (Radivojevic, Rehren, Farid, Pernicka, & Camurcouglu, 2017). Nowadays, metallurgy has grown into a major industry and it has become impossible to imagine society without metals. In the pyrometallurgical industry, coolants (low temperature liquids, for example water) and pyrometallurgical phases (high temperature liquids, such as slags, mattes and alloys) are typically present in close proximity of each other. The interaction between these two phases can have catastrophic consequences (Tveit et al., 2008; Ferguson & Zsamboky, 2017). A vapour explosion may occur as the consequence of the rapid evaporation and expansion of the coolant. Whereas the volume of a gas increases linearly with the temperature (approximately a factor four by heating from 100°C to 1300°C), a simple calculation of the ratio of the two specific volumes shows that evaporation causes the volume of water to increase by a factor of 1700 at 100°C and ambient pressure (Table 1 and equation (1)), a number that was also found in literature (George, Nexhip, George-Kennedy, Foster, & Walton, 2006). The volume change occurs so fast that it resembles an explosion, hence the name vapour explosion. Such an explosion at industrial scale can cause economical losses, bodily injuries or even fatalities.

Jan 1, 2019

By Ernest Becker

Golder Associates provided overall radiological direction and assistance to the client in their interactions with the Canadian Nuclear Safety Commission and operational radiation protection services for the remediation of a calciner that had been used to process uranium. The project was somewhat unusual in that the radioactivity from within the calciner room was removed from the site and the cleaned steel recycled. The presence of yellowcake within the process equipment required stringent radiation protection measures. This project was completed successfully with minimal radiation exposures to the workers and the effective protection of the environment.

Aug 1, 2010

By Gordon L. Kidd

The object of this paper is to show the relations of the East Coulee coal area to the near-by Willow Creek, Wayne, Rosedale, and Drumheller areas, all being parts of the Drumheller field. The word ?area? is here used in a more local sense than that employed by Dr. J. A. Allan, whose. 'area' is rather comparable with the 'mining division' in British Columbia. I have drawn freely from the published information, particularly from Dr. Allan's report on the "Geology of Drumheller Coat Field, Alberta", and from Dr. E. Stansfield's paper on " A Chemical Survey of Alberta Coals", to whom thanks are due. The Drumheller field is served by branch lines of the two principal Canadian railways. The C.N.R. traverses the district by its Goose Lake line from Calgary to Saskatoon; and the C.P.R. by a line from Calgary to Acme and then southeasterly to Drumheller, where it effects a junction with the C.N.R., over which the C.P.R. has running rights as far as Rosedale. From Rosedale, a joint line built during the summer of 1928 extends about forty miles down the Red Deer river to the mouth of Bull Pond creek. From that point the C.P .R. turns more southerly to connect with the Bassano-Empress line. The C.N.R., it is expected, will eventually proceed eastward to connect with a transcontinental line. The joint line from Rosedale down the Red Deer river opened up the Willow Creek and East Coulee areas.

Jan 1, 1929

By Edouard Asselin, Tasawar Javed

The precipitation of hematite from ferric sulphate - cupric sulphate - lithium chloride acidic solutions was studied in a batch reactor. The effect of several variables on the extent of hematite precipitation as well as on its crystallinity and purity was investigated. The variables studied include: initial ferric concentration (1.5 - 30 g/L), retention time (0 - 12 h), initial sulphuric acid concentration (0 - 30 g/L), temperature (150 - 220 °C) and chloride concentration (0 - 25 g/L). The results show that hematite is preferentially precipitated at lower initial iron concentrations. Longer retention times increased the fraction of hematite in the precipitates but did not affect its crystallinity to a significant extent. On the other hand, higher temperatures increased the purity and crystallinity of the hematite. At lower acid concentrations hematite and goethite were precipitated. However, only hematite was precipitated when the initial acid concentration was > 12.5 g/L. Better crystalline hematite was formed at lower acidities. Increasing chloride concentration increased the amount of hematite and decreased the amount of iron sulphate hydroxide phases, but did not affect the crystallinity of the hematite.

Jan 1, 2015

By W. T. Gotheridge

The principal sources of coal-dust underground are, of course, coal, and the working of coal. Coal-dust is most dangerous when it is in the finest state of division. This class of dust is found mostly on the roads, being blown or shaken off the loaded trams in transit, or carried in suspension by air currents. The air current passing from the working faces may also carry dust in suspension into the return airway, and the air current from the surface may carry dust from the shakerscreens into the intake airways. The mosl dangerous dust we have to contend with is, (a) that which is most finely divided, and (b) that which contains the most volatile matter, including the inflammable occluded gases, and also oxygen absorbed from the air. According to experiments, coal-dust in a fine and dry state would intensify an explosion, in air free from fire-damp carrying in excess of 3 ozs. of fine dust or 6 ozs. of coarse dust per cubic yard. The volatile matter in the dust must be between 12 and 31 per cent. in the ash-free coal, the latter percentage giving the highest flame velocity. It is vary difficult to propagate flame where coal-dust contains a large percentage of stone-dust, (say 50 per cent.). Shale-dust or other incombustible dust containing no volatile hydro-carbons or carbonaceous matter will prevent the extension of an explosion if mixed with coal-dust in proportion of say 70 per cent., and if the dust is finely divided and dry.

Jan 1, 1924

By H. Assadi, S. Reutzel, D. M. Herlach

Intermetallics exhibit unique solidification behaviour due to their chemical longrange order. This includes, for instance, generally slow solidification kinetics, and in some cases, an anomalous partitioning behaviour. In the present work the electromagnetic levitation technique - complemented by theoretical modelling - is used to explore various aspects of this behaviour, as observed in solidification of B2 phase in undercooled melts of the Ni-Al system. Moreover, a phase-field model is developed and used to illustrate the effect of chemical order on the solidification kinetics of a B2 phase in a model system. The phase-field model provides an additional basis for the simulation of solidification microstructures in intermetallic forming systems. Both experimental studies and theoretical work signify the role of chemical order in solidification of intermetallics.

Jan 1, 2006

By Alan B. Morrow, William A. Poe

"Minerals processing operations are constantly challenged with improving production rates, yields, energy efficiency and process stability. Advanced Process Control has proven to be an effective tool for improving operations by capturing the full process capabilities consistently. However, the velocity of applying the technology as well as the sustainment of these significant benefits has been hampered by the usability of the software and adaptability of the applications.Some of the new technology developments that improve the usability and adaptability of advanced process control include:• modern and intuitive user interfaces,• customizable models to support unique process behavior,• fast and flexible OPC connection tools,• automated model building,• integration with first principles dynamic models and• improved performance monitoring.This paper will briefly discuss the new technology developments that have improved the usability and adaptability of advanced process control and how this can affect minerals processing operations.In today’s environment, Minerals Processing plant managers continuously face new challenges and requirements including:• higher energy efficiency,• increased run lengths,• reduced product quality variability,• reduced emissions,• higher availability, and• lower operating costsOperating a unit to meet these challenges in real time is not easy for operators and conventional process control systems. However, innovatively using existing technologies in Minerals Processing plants can improve operations on a minute by minute basis and reap significant benefits.Advanced Process Control (APC) can extract the maximum performance benefits from existing equipment while respecting plant operating constraints. Expensive capital projects to upgrade equipment are not always necessary. Advanced Process Control can deliver significant economic benefits by maintaining the plant at its most profitable point as conditions change."

Jan 1, 2016

By Michel Noël

Cet article présente une compilation partielle des mesures adoptées pour la fermeture des haldes de stériles pour des mines situées au Canada et en Alaska, et dont le climat comporte des hivers froids. L?article présente également le processus de sélection qui a été suivi pour certaines de ces mines. Les exploitations minières produisent habituellement des quantités de stériles qui peuvent être importantes. De plus, la nature du dépôt minier ainsi que la roche mère vont souvent entraîner des impacts sur l'environnement. Ces impacts doivent être gérés non seulement durant les opérations minières, mais souvent à très long terme après la cessation de l?exploitation minière. Les plans de fermeture de mine doivent par conséquent procurer des solutions à très long terme, voire même à perpétuité dans bien des cas. Le processus de sélection implique souvent l'évaluation des risques liés aux responsabilités environnementales et financières. Il doit considérer l?aspect scientifique, comporter une définition des objectifs, tout en incorporant une gestion des ressources et des plans de travail. La planification de fermeture est essentiellement un exercice de prise de décisions comportant des contraintes. Une matrice de classement basée sur la performance et le risque est souvent développée durant ce procédé pour identifier les options préférées. Les études de cas présentées dans cet article présentent quelques exemples. L?état des connaissances sur le drainage acide minier provenant des haldes de stériles a augmenté considérablement au cours des dernières décennies. Ceci n?a pas nécessairement augmenté le niveau de complexité des méthodes adoptées pour la fermeture. Une approche qui est fréquemment utilisée consiste à stabiliser les pentes des haldes de stériles en abaissant la pente des talus pour ensuite recouvrir les stériles d?une couche de sol pour soutenir la végétation. De telles couvertures empêchent les animaux d?avoir un contact direct avec les stériles, minimisent l'érosion et réduisent l'infiltration à divers degrés. L'inclusion d?un traitement des eaux dépend évidemment de la qualité de l'eau au point de déchargement.

Nov 1, 2008

By A. Brown

The swift decline of coal during the period of unprecedented expansion in the Canadian economy is a phenomenon deserving careful examination, because the underlying forces contributing to this decline may have broader implications in our national economy. At the present level of technology, coal is more difficult to process, transport and utilize than liquid and gaseous fuels. Fundamentally, it is a matter of limitation in technique. Because coal is a vast store-house of energy in Canada, the reduction of these limitations is in the long-term national interest.

Jan 1, 1967

By Pingchao Ke, Zhihong Liu

Fe(III)-As(V) precipitates were synthesized from the Fe(II)-As(V)-SO42--H2O system at 90°C in initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The synthesis were carried out by introducing oxygen gas into the system to oxidize Fe(II) ions into Fe (III) ions, and at the same time, adding aqueous sodium carbonate solution into the system to neutralize the acid released by the hydrolysis reactions, with the purpose of keeping the pH constant at 1.5±0.05. The precipitates obtained were characterized by XRD, chemical composition analysis, SEM, XPS, and Raman spectrum. The results indicated that the particles in the precipitates were in the morphology of irregular aggregation with their sizes in the range of about 1–4 µm. The precipitates consisted of scorodite, ferric arsenate and amorphous hydrated ferric oxide, of which amorphous hydrated ferric oxide formulated as Fe(OH)x(SO42-)y. The characteristic XPS peaks of Fe-AsO43- and Fe-O in the precipitates located at 711.8 and 713.3 eV, separately, and the existence of amorphous hydrated ferric oxide led to two series of shake off lines developed over the end of high binding energy of Fe2p XPS. The precipitates were stable in TCLP tests at pH 4.93 for 60 hours with the arsenic concentrations in the leaching solutions being 0.27 mg/L and 0.59 mg/L for the precipitates prepared in the initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The tests for the long-term stability of the precipitates were carried out by leaching them for 40 days at 25°C under various media in the pH range from 9.50 to 10.57, and the results showed that the precipitates synthesized in this study were much more stable than those by previous researchers.

Jan 1, 2017

By Engin Burak Anil

Objective, accurate, and fast assessment of damage to buildings after an earthquake is crucial for timely remediation of material losses and safety of occupants of buildings. Laser scanners are promising sensors for collecting geometrical data regarding the damaged states of buildings, as they are able to provide high coverage and accuracy at long ranges. Yet, we have limited knowledge on the performance of laser scanners for detecting earthquake damage, and requirements of such data collection. This paper focuses on characterizing the performance of laser scanners for detecting thin cracks for damage assessment of reinforced concrete frames. We identified a series of crack parameters based on the state-of-the-art damage assessment codes and standards. Similarly, we identified parameters, which affect the performance of laser scanners for detecting cracks, based on prior research in this area. We studied the width, depth, and orientation of cracks; sampling interval of the scanner, and the range of the laser beam from the surface. Effects of these parameters on the detection of the minimum crack size were determined in an experimental setting. An automated algorithm was used to analyze the data. The results show that it is possible to detect as small as ~1mm cracks.

Aug 1, 2013

By P. K. Kaiser

3-D virtual reality (VR) visualization has opened new opportunities for complex 3D (x, y, z), 4D (x, y, z, t) or even nD data interpretation. The integration of common earth models (3D geologic data), mine models (3D excavations and stress), extraction models (1D time sequencing or mine sequencing) and nD monitoring data (e.g., seismic event parameters) into a common mining process model provides a platform for experts in various fields to better design, evaluate, monitor and modify mine plans throughout a mine?s life; from feasibility, through operation, to closure. Viewing seismic data in a stereoscopic VR environment within a mining process model offers data interpretation processes previously unavailable at lower dimensionality. MIRARCO has developed data analysis and viewing processes specifically designed to enhance microseismic and seismic data interpretation in a collaborative, immersive VR environment; bringing mine personnel and expert consultants together to evaluate data and make strategic decisions for cost effective and safe mining. Seismic events cause immediate hazards (rockbursts) and microseismicity causes gradual hazards through its cumulative effect in rockmass degradation. The focus of this paper is on understanding seismicity from a mine safety and mine planning perspective; in particular, how seismic migration patterns relate to the rockmass response to mining. The benefits of innovation in seismic data interpretation are significant, e.g., for hazardous work area identification, allowing better formulation of re-entry policies and workforce allocation planning, as well as allocation of effective support systems to strategic areas of elevated risk. Better understanding of the overall response of a mine to extraction also facilitates mine planning and design, assisting in reducing production costs and thus in enhancing profitability.

Apr 1, 2005