Search Documents

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-Fe0x-Ca0 ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04. 0

Jan 1, 2007

By Janne Karonen, Stephen Hughes, Mikael Jåfs, Jan Stål, Hannu Johto

End-of-life electrical and electronic scrap material attracts attention as a good opportunity for new value creation through efficient metal and energy recovery of such materials. On the other hand, the treatment of such wastes becomes important to avoid problems for society and environment. Treatment of such secondary raw materials faces multiple challenges due to their increasing complexity and evolving nature. Processing of these complex scrap materials together with recovery of a wide range of valuable metals with a combination of pyrometallurgy and hydrometallurgy using Outotec technology is discussed in this paper. One key consideration is environmental performance which needs attention when processing such complex secondary E-waste materials. Outotec has successful experience with commercial projects in the countries at the forefront of environmental and operational standards. INTRODUCTION Increasing attention has been drawn to the responsible processing of end of life Waste Electrical and Electronic Equipment (WEEE) as part of metals recycling, especially copper. It has been estimated that the amount of WEEE globally in 2016 was around the level of 46 Mtpa (Balde et al., 2017), representing a major disposal challenge but at the same time huge opportunity for resource recovery. The potential for increasing the recovery is high, because the official recycling rate of WEEE is in 2016 only 20% (Balde et al., 2017) and at the same time the estimated increase of the WEEE amount is between 3 and 5% per annum in the EU (Eurostat, 2019).

Jan 1, 2019

By A. M. Gaudin

Introduction The discovery of artificial radioactivity, that is, of radioactivity of acorns other than those which are naturally radioactive, has increased vastly the possibility of using radioactivity as an analytical cool. The incomparable value of radioactive atoms, which are commonly termed tracers, arises from the extreme sensitivity of this analytical method. To get an idea of this extreme sensitivity it may be useful co recall that gravimetric analytical methods will not permit the weighing of anything much lighter than one-hundredth of a milligram of material. Under the most favourable circumstances, this represents an uncertainty in the answer of 1016 acorns, or 10,000,000,000,000,000 acorns. Accurate spectrographic methods possibly have a sensitivity 10,000 times greater than this, but the uncertainty is still of the order of 1012 atoms. The tracer permits ascertainment of decay of a single atom so that its sensitivity, without half trying, can be several orders of magnitude greater than that of any other method available co chemists. In addition co the sensitivity of tracers to which reference has just been made, tracers have another property which makes them unique. A radioactive atom is almost exactly like the corresponding non-radioactive acorn m regard to its electronic structure, and therefore in regard to its chemical properties. The nucleus is different, but the nucleus does not participate in chemical reactions. Therefore, a tracer acorn behaves like an ordinary atom until such time as its nucleus undergoes a catastrophic decay. This unique property permits one to use tracer acorns as atomic spies and therefore to follow the behaviour of acorns of a certain kind among their own kind. In other words, the tracer method permits us to study and measure what we call self-diffusion. All of the uses of tracers that have been made depend on the two properties co which reference has been made.

Jan 1, 1949

By Katherine (Kate) Bruce

Aurora College ? Yellowknife Campus, in partnership with the Northwest Territories Mine Training Society and industry partners, has developed a 6 ? week program on Underground Mining for delivery in Northern communities. The goal of the program is to inform and connect Northern residents to the career potential at existing and future mining operations throughout the Northwest Territories. The program content includes an introduction to the mine life cycle, basic underground mining methods, the use of technology in training via desktop simulators for underground mining equipment, safety in the workplace, and essential skills training (Ready to Work - North) and assessment. Students completing the short program may then choose to continue into a long (12-week) program to be offered at the Yellowknife Campus. This program expands upon the initial introduction and includes modules on NWT geology, environmental studies, underground mining processes and underground mining equipment operation using the larger enclosed cab simulator for a variety of equipment being used at northern mining operations. Success of both programs will depend upon a variety of factors, many of which are outside of the control of the developers of the training modules. These will be investigated throughout the presentation. Connecting northern employers with northern employees is a major concern. It is hoped that through the development and implementation of a program such as this, that the connection can be made and sustained allowing continued employment for the life of northern mining operations.

May 1, 2008

By L. López

Argentina reported about 40,000 tonnes of uranium (tU) as reasonably assured resources and inferred resources for the production cost category <130 US$/kgU in the OECD-NEA/IAEA classification scheme. These resources belong to the following projects: Sierra Pintada, Cerro Solo, Don Otto, Laguna Colorada, Laguna Salada, Meseta Central and Amarillo Grande. With three heavy water reactors in operation and an approximate installed capacity of 1.7 GWe, the current natural uranium requirements are about 220–250 tU per year. Based on various nuclear growth scenarios, it is estimated that by 2030 there will be a generation capacity of some 3,092 GWe for the reference case, with raw material needs of some 486 tU per year. Currently, there are no perspectives for local uranium production in the short term, and it is thought that uranium projects with identified resources must complete resource delineation and advance in technical pre-feasibility studies for the recovery of uranium. It is expected that Argentina continue meeting the uranium demand with imports in the next following years. In the Latin America region, both Brazil and Paraguay could be considered as potential uranium suppliers. In conclusion, despite the apparent growth prospects for the use of nuclear energy to generate electricity in Argentina, there are no immediate prospects for the provision of uranium oxide concentrates from domestic deposits for fuel fabrication. This has implications for supply and energy security.

Jan 1, 2020

By M. E. Holter

"Five main lignite seams occur in the Tertiary Ravenscrag Formation in the Eastevan area, at depths of 100 feet or less. They are named, in ascending order: the Boundary, Estevan, Souris, Roche Percee and Short Creek seams. A total sequence of approximately 250 feet is represented by the coal beds and interstratified clays, silts and sands. Strata dip to the southeast at 25 feet per mile or less and trike northeast. Large areas underlain by coal seams at shallow depths are delineated. Reserve calculations are dependent on detailed information on seam thicknesses and feasible stripmining depths. The stratigraphically higher seams are thinner on the average than lower seams and this, together with the increase in elastic size fractions in higher strata, suggests a retreat of a Tertiary marine margin to the south during the closing depositional history of coal seams and associated strata."

Jan 1, 1972

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By S. Glen

Cyanide management practices on modern gold plants are becoming more onerous, due to environmental pressures, particularly for signatories to the International Cyanide Management Code. Operations are therefore seeking to reduce levels of weak-acid dissociable (WAD) cyanide reporting to spigot discharge as well as to any eventual discharges from the tailings storage facility (TSF). Current gold industry standard processes primarily include the oxidation of cyanide by means of sodium meta-bisulfite (SMBS, or SO2) with air, Caro&apos;s acid (H2SO5) or hydrogen peroxide (H2O2). These processes require the transport and usage of expensive oxidizing reagents, along with the safety and environmental issues associated with these corrosive and toxic chemicals. Maelgwyn Mineral Services (MMS) has developed the MMS CN-DTM process, which utilizes the Aachen ReactorTM, a high-energy mass-transfer superoxygenation system, in conjunction with an activated carbon-based catalyst and no additional reagents, to increase the rate of cyanide oxidation to cyanate, the thermodynamically more stable form. Testwork conducted at the Maelgwyn Australia testwork facility in Perth Australia is described, at both pilot scale and continuous bench-scale, on a sample of tailings effluent obtained from an Australian gold plant. WAD cyanide is demonstrated to be lowered using the MMS CN-DTM process from an influent of 130 mg/L to the required levels for discharge to TSF (<50 mg/L). The continuous test results showed stable operation over three residence time turnovers. The pilot-scale results demonstrated the efficiency of the process at the reasonably large scales required for engineering cost estimation.

Jan 1, 2011

By Xiu-Xiang Tao

This study investigated bio-liquefaction of lignite and its model compounds of thymol, bezioc acid and quinoline by a fungus, Hypocrea lixii AH. It analyzed, during bio-liquefaction, enzyme activity of oxidase, LiP, Lac, MnP and polyphenol oxidase, and degradation products by UV-Vis, FTIR, 13C NMR and GC-MS. The results showed that the bio-liquefaction percentage (by mass) of lignite was up to 44.86 %. The bio-liquefaction products of lignite were mainly aniline, amide, ether, carboxylic acid ketone and ester. The aromatic ring number was 1-3 with an aromatic carbon ratio of 0.328, which indicated rings opening, bonds breaking and oxidation reaction. By considering with the enzyme activity analysis results, it showed that LiP and Lac catalyzed reactions to open aromatic cycles and to break bonds; esterase to break ester bond; and peroxidase in oxidation reaction.

Aug 1, 2013

By Robert B. Parsons

"The mining industry is adjusting its sights to take a shot at the rising level of non-profit taxes which threaten to handicap the industry &apos;s competitive advantage. In the case of this particular expedition, the industry evidentally has a strong ally - the country&apos;s mines ministers. It appears that an initiative is under way to assess the impact of non-profit taxes on mining in Canada as compared to other mining nations.IntroductionSeventy-five years ago, Canadians were unceremoniously introduced to something called income tax. Since then, income tax has been identified as the source of countless evils ranging from the common cold (attributed to stress) to the demise of the economy. Some years later, the provinces jumped on the bandwagon with their own income taxes, and later on with mining taxes. These profit-based taxes had some appeal to elected officials and to a segment of the populace. The onus of the taxes varied directly with the ability to pay (in theory, at least). Previously, the principal sources of government revenues had been property taxes and customs duties, which were viewed as possibly being somewhat regressive in nature.The mining industry has always had concerns about different aspects of income and mining taxes - the tax rate is too high or the depreciation rate is too low, and so on. Recently, though, the industry has turned its sights on the expanding array of taxes which are not based on profit, including payroll taxes, capital taxes, water taxes, sales taxes, fuel taxes, property taxes, environmental levies and user fees. The industry is seriously concerned that the rising level of non-pro fit-based taxes is not only hampering the industry &apos;s ability to reinvest in Canada, but is also placing Canada at a disadvantage in terms of trying to attract new investment capital."

Jan 1, 1992

By L. R. Bottomer, G. M. Leary

"The Copper Canyon property is located in the Galore Creek area of northwestern British Columbia. Porphyry copper-gold mineralization on the property is notable for its high gold content and close spatial relationship with a distinctive suite of high level syenitic and monzonitic intrusions, and pseudoleucite-bearing volcanic country rocks. The style of alteration and mineralization is similar in many respects to the nearby Galore Creek deposits.The current geological resource of 32.4 million tonnes grading 0.75% Cu, 1.17 g/ t Au and 17.1 g/t Ag is insufficient to support a mining operation, but definition of additional reserves combined with improved transportation infrastructure in the region may change this in the future. The climate, topography and proximity to an active glacier indicate that the most likely production scenario is an underground bulk mining operation, with the ore being milled offsite.IntroductionThe property is located at 57°07' North latitude, 131 °21' West longitude, on NTS sheet 104G/ 3W, approximately 160 km northwest of Stewart and 90 km south of Telegraph Creek (Fig. 1). The Galore Creek camp and airstrip are located 6 km to the west. Current access to the property is via helicopter either from Galore Creek, or from the Bronson Creek airstrip 32 km to the south-southeast.The deposit occurs within the Boundary Ranges of the Coast Mountains, on the north side of the east fork of Galore Creek, which flows northerly into the Scud River and thence westerly to the Stikine River.Topography is rugged. In the deposit area, elevations range from 1130 m to 1750 m. Valley glaciers and permanent snow and ice fields are characteristic of the region at these elevations, and at its southern limit, mineralization is truncated by the East Fork Glacier.The property is entirely above the treeline, and except for areas of moraine cover and talus slopes, outcrop is abundant."

Jan 1, 1995

By K. Spence

"The notion of “value” has always been a subjective and contentious issue. Indeed, value is in the eye of the beholder. There are as varied methods and practices for valuing property, as there are industries in which they are applied. For example, there is replacement value, insurance value, salvage value, appraised value, book value, and fair market value, to name a few, although in the mining industry, valuations usually refer to fair market value.In the Canadian mining industry, at present, there are no comprehensive regulations or guidelines that specify which approaches or methods are appropriate for use in the valuation of mineral projects. In January 1999, The Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. Among the approaches to be considered are included the following: the discounted cash flow approach, the cost approach, the option pricing approach and the market comparables approach. In addition, methodologies differ depending on whether the project is at the exploration stage or the producing stage.The CIM Special Committee on the Valuation of Mineral Properties (CIMVal) expects that its final report will form the basis for a Canadian code or standard for the valuation of mineral properties."

Jan 1, 2002

By A. Zorkovská, S. Castro, P. Baláž, Z. Bujnáková

Enargite (Cu3AsS4) belongs among refractory copper minerals with very low hydrometallurgical extractability of copper. An application of enargite leaching in acid solutions leads to simultaneous dissolution of copper and arsenic and the final leach solutions have to be treated for the separation of both elements. However, the alkaline leaching of enargite is selective. Arsenic passes into leach while produced copper sulphide represents the raw material suitable for pyrometallurgy. The hydrometallurgical processing of mineral can be influenced positively by mechanochemical route. We have shown that more than 80 % of arsenic can be extracted from enargite concentrate by atmospheric alkaline leaching at 95 °C when mechanical activation in an attritor is applied. The produced Cu2S can be further treated with elemental iron where mechanochemical intervention is applied in the second stage of enargite processing. The final product forms Cu/FeS nanocomposite from which copper nanoparticles can be easily separated. The illustrated concept of copper obtaining from copper sulphide is an example of so-called “dry” processing, as reactions in gas and liquid phases are excluded. This concept of environmentally friendly metallurgical processing can be classified as an impetus for novel technology to produce copper from enargite concentrates.

Jan 1, 2012

By Ralph W. Edie

"IntroductionTHIS PAPER presents some analyses of diabases from a number of metallogenic provinces in Canada and the United States. It is intended as a contribution to the literature on the genesis of mineral deposits associated with diabase.As it has been in the past, opinion today on the origin of the cobaltnickel- native silver and associated pitchblende type of deposit is sharply divided. Some geologists hold that this type of deposit is in some way genetically related to intrusive diabase; others are of the opinion that the deposits are related to granite. The controversy, like others of a similar nature, probably will not be settled satisfactorily for many years to come, •but in the meantime it is recognized that, with respect to most deposits of the type referred to, altogether too few facts are known for accurate conclusions on genesis to be drawn. To contribute in a small way to factual data on this whole .problem, the writer analyzed diabase from several districts in Canada in which deposits of the aforementioned type occur. For comparative purposes, the copper, cobalt, and nickel content of diabase from Cornwall, Pennsylvania, and of norite from the Sudbury basin of Ontario, was also determined.Insofar as is known, none of the analytical work undertaken had been previously carried out."

Jan 1, 1953

By Chuanhui Cao, Shimei Liu, Xiaojing Li, Yueyuan Zhou

"Force analysis on weakly-magnetic particles and non-magnetic particles in magnetic field are presented, using a kind of permanent magnetic drum magnetic separator, which is designed with strong specific magnetic force and open magnetic system. Its surface peak intensity reaches to 1.0T, and the distribution density of capture line is 1.25×103/dm2. Qualitative analysis on the particles including its magnetic property, particle size, motion speed, magnetic field intensity, etc. is also presented to calculate the separating parameters for the drum separator. Experiment was conducted for the separation of fine weakly magnetic minerals for example ilmenite. The practicability to separate the minerals using separator designed with open magnetic system has been proved, providing an economic way for efficient separation of micro-fine weakly magnetic minerals and upgrading of non-metallic minerals. INTRODUCTIONMagnetic separation is a mineral processing method based on the differences of magnetic properties between minerals in inhomogeneous magnetic field (Sun, 2007). Currently for separation of micro-disseminated weakly magnetic iron ore, electromagnetic high intensity magnetic separators with closed structure of magnet system are often used. And for the separation of strongly magnetic minerals such as magnetite, low intensity drum magnetic separators with open magnet system are often used. In order to lower the operation costs and improve energy efficiency, it is important to develop efficient high intensity permanent magnetic separator with open magnet system, to some extent replacing high intensity electromagnetic separator.Oberteuffer (1974) discussed the magnetic force and competing forces in magnetic separators which compete with the magnetic forces and act on all of the particles which travel through the separator are those of gravity, hydrodynamic drag, fraction, and inertia in magnetic separation."

Jan 1, 2016

By T. Donkin, B. Patterson, M. I. Guthrie, J. T. Ross

"The interest in the use of sensor-based particle ore sorting has increased significantly with the recent advances in the sorting technologies and higher capacities per unit. This technology has the potential to provide great value in processing lower grade ores from the mine whilst delivering higher grades to the mill as well as in upgrading waste rock into ore. Typically, the focus is on the amenability of the ore to ore-sorting and associated reductions in the consumption of energy, water and consumables. However, layout has a significant impact on the installed cost of a concentrator and the layout impacts from fitting an ore-sorting circuit into the concentrator plan need to be carefully considered. This paper examines layout considerations that play an important role in ore sorting projects. These include additional crushing and screening requirement, transportation of the rejected material back to the waste stockpile (mine fleet requirements) and effects on concentrator footprints.INRODUCTION Ore sorting has been practiced throughout history with an early report by Agricola in 1556. Metallic and non-metallic minerals were extracted from rocks by laboriously breaking them with hammers and picks and hand-picking selected material with higher grade off a table. The concept has not changed but the sorting technology has evolved significantly over the last 20 years. Ore sorting is usually a dry process in which a portion of the material is rejected based on mineral properties and/or grade. The methods used for sensing ore particles cover a large range of physical properties. A variety of sensors are available that differ on the discrimination technique that is used, which include: photometry, radiometry, conductivity, magnetism, microwave, X-ray transparency: X-ray transparency and luminescence and UV fluorescence (Sivamohan and Forssberg, 1991; Wotruba, 2006). There are two main ore sorting techniques: particle ore sorting and bulk ore sorting. According to Nadolski et al (2018), the potential for sorting is determined though analysis of grade heterogeneity within the orebody (greater heterogeneity represents more opportunity to add value to a project) at the scale of the intended sorting unit size."

Jan 1, 2019

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By W. L. Falconer

"IntroductionThe very recent emphasis on the importance of the northern portions of the Alberta basin as a prospective oil province has led the oil companies northward into new and undeveloped territory. Northern Alberta is a land of continuous forest, covering a plains-type topography. The plains are only occasionally broken by sharp, broad river valleys. Tributary streams head up quickly and very soon lose themselves in large undrained areas. It is these pseudo-swamps that cause most of the troubles and headaches of the oil explorer.The rivers have served as the main transportation arteries since people first ventured into this area. The bush is being pushed back, but the advance is slow and there is very little more than trappers' trails beyond a few miles from the Northern Alberta Railway lines and the recently built Grimshaw or McKenzie Highway. Indeed, bush and muskeg flank many miles of the railways and roads within as close a distance as fifty miles of Edmonton. Northern Alberta is pioneer country in the truest sense of the word, and our greatest problems derive from this fact. In all pioneer areas, the first requirement is the development of access roads, and before active oil exploraton can get down to the job at hand these roads and trails must be an accomplished fact. There are two factors in Northern Alberta which offer discouragement to the oil explorer: the first and greatest stumbling block is presented by the numerous muskegs, large and small; the second is the fact that road building uses up so much of reservation time. Of course, the second is aggravated by, and a direct result of, the first. So we come back to the main problem facing the development of the north - the muskegs."

Jan 1, 1950

By M. M. Holgate

"Porosity neutron deflection scales can be derived more easily by cumulative correlation than by the conventional method of plotting corresponding points on a graph. The micro-log can be used as a porosity datum for the neutron log by transforming the permeability cut-off it shows to a porosity cut-off by a permeability-porosity function obtained from core analysis. Porosity footage values calculated in this manner from the neutron log are within 20 per cent of core analysis values."

Jan 1, 1960

By W. J. Weymark

"The Gregg River project is located 40 kilometres southwest of Hinton, Alberta, adjacent to and east of Jasper National Park. This metallurgical coal mine has been developed as a joint venture between Gregg River Coal Ltd. (a subsidiary company of Mana/ta Coal Ltd.) and seven Japanese companies. This 200-million dollar project consists of a conventional truckshovel open-pit operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. Mining operations started in October 1982 with plant start-up following in April 1983. Introduction This paper is an overview and update of the Gregg River project, a metallurgical coal mine being developed as a joint venture between Gregg River Coal Ltd. (a subsidiary of Manalta Coal Ltd.) and seven Japanese companies. The Gregg River Coal leases cover 3440 hectares and are located 40 kilometres south of Hinton, Alberta, adjacent to and north of Cardinal River Coal Mine (Fig. 1). This 200-million dollar project consists of a conventional truck-shovel operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. A total of 31.5 million tonnes of clean metallurgical coal will be sold to the Japanese over a fifteen-year term. At present, mining operations are ahead of schedule and the plant started up on schedule in April 1983. Access and Climate An all-weather road, Highway 40, connects the minesite with Hinton (the nearest commercial centre) and a Canadian National Railway (C.N.R.) spur line connects the minesite with the C.N.R. main line in Edson. Hinton is accessible by road chartered airline and rail. ' ~h~ rug~ed and varied topography in the area creates large vanations m temperature and precipitation over short distances. The region is characterized by precipitation throughout the year long cold winters and short cool summers. The mean temperatur~ of the area range from a low of -14°C in January, the coldest month, to a high of 12°C in July, the warmest month. Long-term precipitation data indicates a mean yearly precipitation of 870 mm of which 620Jo occurs during the summer months."

Jan 1, 1985