Search Documents

By T. E. Smith

"This paper describes the application of a motor-driven flywheel unit, known as a peak shaver, to compensate for the cyclic load fluctuations of a large electric dragline installed at Pine Point Mines, near Great Slave Lake in the Northwest Territories. Of particular interest in this application is the fact that the power system supplying the dragline is a relatively small isolated system, with the major generating source approximately 170 miles from the mine.The cyclic load fluctuations of the dragline are theoretically capable of producing a maximum swing of up to 11 megawatts, which approaches nearly 50% of the installed generating capacity. To reduce these load fluctuations to acceptable limits various alternatives were considered, leading to a decision to install a peak shaver to optimize the operations of both the mine and the power system. Without the peak shaver, the dragline operations would be severely curtailed and additional diesel generation would have to be run at considerable expense, otherwise the power system frequency fluctuations would be totally unacceptable. With the peak shaver, power and frequency fluctuations are kept within tolerable limits, and optimum economic operation of the diesel generation is obtained.The paper outlines the steps leading to the selection of the peak shaver as the compensating device, describes the equipment installed and gives details of operating experience with the dragline/peak shaver combination since installation early in 1979. This .peak shaver is the first of its kind in North America, the only other peak shaver installation being in Australia.IntroductionPine Point Mines Limited owns zinc-lead mining and milling operations located at Pine Point, Northwest Territories, 5 miles south of Great Slave Lake (Fig. I). The company is staffed and managed by Cominco Ltd., which has a 69% interest in Pine Point Mines.Mining activity in the Pine Point area was first recorded in 1898, when the Yukon gold rush was on, but when the zinc/lead showings in the Pine Point area did not yield much in the way of gold, interest in the area soon waned. Cominco Ltd. first acquired some claims in the Pine Point area in 1928, but interest was sporadic until the early 1950s, when extensive exploration indicated rich pockets of zinc/lead ore near the surface. Pine Point Mines Limited was formed in 1951, with Cominco acquiring a majority interest in the company."

Jan 1, 1980

By Jerry M. Whiting, Neil J. Duncan

"Does Canada need a mining industry? Isn't it a chronically depressed collection of businesses that pollute the air and water and tear up the countryside? Wouldn't it be better if Canada's investors devoted their attention to high-technology endeavours, tourism, and other relatively pleasant tasks?Probably the answer to whether Canada needs a mining industry in the 21st century is to look at the real mining industry that is in operation today. The facts indicate that mining is a very important contributor to Canada. It has certainly encountered some challenging times during periods of recession, and it face s severe and continuing problems of cost and competition in world markets. However, uneconomic mines have been closed, others suspended, and productivity has risen dramatically with employment at 77 000, down from 101 000 in 1981. The country's metal and non-metal mines, metallurgical plants and semi-fabricated metals industries employed an estimated 378000 workers in 1986, and paid wages than any other sector of the Canadian economy. This effort resulted in the production of 60 different metals, non-metals and structural minerals valued at $13.5 billion.The trade aspects of the mining industry are of paramount importance. If there is a reason for this situation to change during the next century. it eludes the authors. Canada has the well-developed expertise to discover, evaluate, develop, operate and profit from existing and new businesses based in an enormous area endowed with a nearly unbelievable variety of mineral resources. Many countries throughout the world must rely on producers like Canada, if they are to maintain and/or improve their standard of living."

Jan 1, 1988

By D. A. MacFadyen, J. J. Brummer, C. C. Pegg

"The first record of a kimberlite found in Canada (1946) was the identification of thin dykes intersected while drilling for gold in Michaud Township, Ontario.Sampling of the Munro Esker (1964) in the Kirkland Lake area, Ontario, by the Geological Survey of Canada identified the occurrence of detrital grains of pyrope garnets along a length of 35 km of the 113 km tested. A search for the source of the garnets resulted in the identification (1968) of a narrow subsurface kimberlite dyke in the Upper Canada Mine. This discovery resulted in a staking rush. Unfortunately, subsequent work did not identify the source of the kimberlite indicator minerals.During 1978 the Ontario Geological Survey started a multi-discipline study of 29 townships (2560 krn2) in the Kirkland Lake area, to encourage exploration for gold, base metals, and kimberlites. Back-hoe sampling (1979 to 1982), where the overburden was thin, and reverse circulation drilling, in areas of thicker drift, yielded samples of the till. These were analyzed for several elements and a mineralogical identification of the heavy minerals was completed. Pyrope and chrome diopside grains were identified.Studies of the Pleistocene geology indicated only the most recent direction (167 degrees) of ice advance (Matheson) and the associated deposits, out of a possible three advances known to occur in the general region straddling the Ontario-Quebec boundary, is present in the immediate area of Kirkland Lake. Contouring the distribution of pyrope grains (1990) showed a concentration centered over an area of 616 km2 extending down-ice from Gauthier Township. This included a smaller area containing chrome diopside grains. Kimberlite boulders were identified (1981) in gravel pits on the Munro and Misema River Eskers located within this anomalous area. The next step would be to use the airborne geophysical data to locate the kimberlite pipes which yielded the indicator minerals and boulders. The source area is likely to be in the northern half of the Ontario Geological Survey study area."

Jan 1, 1992

By D. C. R. Espinosa, P. Aliprandini, F. P. C. Silvas, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel ores are divided into two types: sulfide deposits and lateritic deposits. About 60% of nickel resources are found in laterite ore, while the remaining 40% is contained in sulfide ore. Laterite ore is usually processed via pyrometallurgical means or through hydrometallurgical techniques that include acid leaching and metal value recovery from solution. In this study, copper and nickel adsorption by Dowex M4195 ion exchange resin from an acidic sulfate liquor was investigated. The acidic sulfate liquor was collected from an atmospheric leaching process (AL) of laterite ore. Ion exchange experiments were conducted in a batch system by varying parameters such as pH, time, metal concentration and temperature. Initially, mono-elemental synthetic solutions of nickel and copper were used in the experiments and then a synthetic solution simulating AL liquor was tested. Test results showed that the resin exhibited high selectivity towards copper and nickel, however, a high concentration of iron in the synthetic AL solution interfered with the recovery of nickel and cobalt by the resin.INTRODUCTION Nickel is one of the most important industrial metals in the world. It is widely used in industrial applications, such as the production of stainless steel, magnets, electroplating and special alloys (Dizge et al., 2009). The main sources of industrial nickel production are sulphide deposits; only 40% of industrial production uses lateritic ores. However, it is estimated that 60% of global nickel resources are found in nickel laterite deposits (Kuck, 2016). Since industrial nickel demand continues to grow, the development of new technologies for the extraction of nickel from laterite ores has become an interesting research topic (Agatzini-Leonardou, 2009)."

Jan 1, 2017

By David L. Anderson

This paper explores the financial impact of the initial version of the Saskatchewan Potash Reserve Tax; first, a one; and second, in conjunction with the other taxes affecting the industry's profitability. A though the introduction of the Reserve Tax is shown to lead to a substantia increase in a hypothetical firm's effective tax burden, the more unusual outcomes frequently attributed to this levy on y occur after the imposition of other non-provincial tax rulings. Despite this qualification, the results obtained suggest that the Reserve Tax undoubted y acted as a catalyst in the polarization of attitudes during the ear y period of industry/government confrontation

Jan 1, 1979

By J. E. Hawley

Introduction The Siscoe gold mine is the most easterly producer of gold from deposits lying in the belt of Keewatin and Timiskaniing rocks which extends east from Kirkland Lake, Ontario, and on through the Rouyn copper area. Unlike many of the deposits in this belt, those of Siscoe are contained almost entirely in a stock of much-altered granodiorite which intrudes Keewatin lavas. They are situated on an island of about one square mile in area, lying in lake De Montigny, Dubuisson township, 40 miles south of Amos, on the Transcontinental branch of the Canadian National railways, and 52 miles east, and slightly south, of Noranda. Geographically, the deposits are favour-ably situated with respect to transportation facilities, a through water-route being available from Amos, along the Harricana river and its lake expansions. The deposits consist of auriferous quartz-tourmaline veins of the fissure-filled type and are of particular interest because of their geological structure and genesis. Furthermore, deposits of a similar type occur both in the Keewatin and in granodiorite bodies to the east, in Dubuisson, Bourlamaque, Pascalis, and Louvicourt townships, and it is hoped that the following discussion may be of some aid in the exploration work now being carried on throughout this general area.

Jan 1, 1932

By Daniel D. M. Adams

In 2004, Rio Tinto started a major project to implement Mine Monitoring and Control (MMC) systems worldwide. A detailed selection processes was undertaken and migration to a standard system was started. Today systems are operating around the world and serve as the core of to many business processes. Implementations include highly union areas, large mines, centrally managed mines, and remote areas. Each implementation has unique challenges but all are working towards the common goal with common systems. This paper reviews two projects that Rio Tinto has deployed in diverse conditions. The projects are the Rossing Uranium upgrade from the original Wenco system to the common standard and Iron Ore of Canada?s general technology upgrade. Also discussed is the future of mining at Rio Tinto, specifically the drill automation projects, and how it is utilizing the common standard MMC systems.

May 1, 2010

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016

By H. Soltanzadeh

This paper summarizes semi-analytical and closed-form solutions that can be used to assess the poroelastic stress changes induced within a porous formation (reservoir) during a pore pressure change. Further, solutions are presented for the stress discontinuities at the interfaces between reservoirs and the rocks that surround them. When used in combination with rock failure criteria, these solutions enable relatively simple analyses of the potential for induced fracturing or fault reactivation within a reservoir or the rock immediately adjacent to it. The latter, in particular, is useful for assessing if the hydraulic integrity of the surrounding rock (i.e., the bounding seal) will be affected by a pore pressure change. The use of the approach presented in this paper is illustrated with an analysis of a pinnacle reef with dimensions and properties representative of reefs in the Zama oil field, northwestern Alberta, Canada. Scenarios of pore pressure decrease (during historical production operations) and pore pressure increase (during several years of acid gas injection operations) are analyzed, for three different idealizations of reservoir properties and geometry (two plane strain and one axisymmetric). These results suggest that that the potential for induced fracturing is not significant at any point within the reservoir or the surrounding rock for both the production and injection scenarios that were simulated. Similarly, fault reactivation was not predicted for the reservoir or any of the points that were analyzed in the surrounding rock. However, fault orientations having the greatest potential for reactivating during historical production operations were identified; thus, illustrating a means of using geomechanical models to focus geological characterization efforts on the features that are most critical to acid gas containment.

May 1, 2009

By Lucas van Latum

A Model for Safety Swiss cheese metaphor of safety layers Image »Multiple layers with independent, often transient failure modes »For a loss to occur, all layers must fail independently and simultaneously ??Latent? failures are due to inherent system flaws ??Active? failures are due to unsafe acts

May 1, 2011

By Jeff Smith

Agenda About NORTHPARKES The NEED The INITIATIVE The SEARCH The PRODUCTS The SOLUTION The RESULTS The Northparkes copper-gold mine in Central Western NSW commenced operations in 1994. Copper concentrate is produced and shipped to smelters in Japan, China & India under long term contracts with spot sales to other Asian countries.

May 1, 2006

By N. Ahern, M. Barbanell

Mercury is often present in gold ores and can be released during processing. In view of health and environmental concerns related to mercury, the mining industry takes leadership in the responsible management of mercury. This paper reviews various aspects of mercury management, including an overview of mercury deportment in typical gold processing flowsheets; trends in mercury legislation impacting the international flow and management of mercury in the gold mining industry; and treatment, storage and disposal options for mercury and mercury containing materials.

Jan 1, 2014

By A. B. Parsons, P. G. Howes

"This article discusses how recent changes in the federal and Quebec .income tax laws have contributed to an improved investment climate for mineral exploration in the Province of Quebec. Individual investors who are resident in Quebec and who are in the highest tax bracket (1984-60.4% marginal rate) may obtain tax benefits that result in only nine cents of each invested dollar being at risk.IntroductionIn a recent submission by the Mining Association of Canada to the Royal Commission on the Economic Union, it was stated that the mining industry ""is no longer discovering and opening new mines at rates sufficient to offset the depletion of existing orebodies and to maintain pre sent output"". With world metal prices still in a depressed state following the prolonged 1981-82 recession, moreover, the continuing success of Canadian mining in world markets will depend on this country&apos;s ability to compete in a new environment characterized by subsidized Third World production . For the most part, this new competitive environment will encourage the development of cost-efficient mines that are better equipped to withstand the troughs and valleys of international metals prices."

Jan 1, 1984

By David J. Morrison

Scarcity of truck tyres, increasing cost and decreasing availability of labour, increases in fuel costs and project budget blowouts have changed the paradigm behind mining equipment selections. The cycle of commodity changes have occurred in parallel with the increasing maturity of continuous mining machinery, mobile in-pit crushing systems and very large scale conveyor belt systems. This paper will consider the merits of operating continuous materials handling systems, mobile in pit crushing systems, relocatable crushing systems, relocatable conveyor systems and automated waste handling systems in place of the more conventional approach of truck haulage.

May 1, 2007

By Edmund C. Bovey

"AS I begin my remarks this morning, please let me say how honoured and gratified I was to receive your invitation to address you here during your deliberations in historic Quebec City. The high esteem in which your Institute is held is reflected in the respect and deference accorded to it by industry across Canada. I feel privileged to be here with you today.I would like to discuss with you some applications of natural gas in the mining industry and suggest to you, in closing, some possible avenues of future development.Natural gas first became avail-able for industrial purposes in Northern Ontario in late 1958. Acceptance of natural gas, as a source of energy by the industry of that area, has been both widespread and gratifying. The mining industry of Northern Ontario has in-creased its annual use of natural gas by approximately 35 per cent each year since 1958. We believe that this trend will continue, al-though we will probably have to accept a more modest 10 per cent annual gain as the market approaches saturation. I would like to explain how we were able to do this and where all this gas is used. Our first sales were largely a matter of price-and the savings we offered were substantial."

Jan 1, 1966

By Binbin Luo, Northeastern University, Chuanyao Sun, Jie Liu, Yimin Zhu, Yanjun Li

"A series of new type collectors a-bromo-saturated fatty acids, CH3(CH2)5CHBrCOOH (a-BHA), CH3(CH2)7CHBrCOOH (a-BDA), CH3(CH2)9CHBrCOOH (a-BLA), CH3(CH2)11CHBrCOOH (a-BMA) were synthesized from saturated fatty acids and bromine by solvent-free method (Hell-Volhard-Zelinski reaction) in laboratory. The micro-flotation tests of quartz mineral were conducted at a relatively low temperature of 15 °C. The adsorption mechanism of such collectors on quartz mineral surface were established by zeta potential measurements, in conjunction with the results of quartz micro-flotation tests. The flotation results showed that the collecting ability is in the order of a-BMA > a-BLA > a-BDA > a-BHA for the flotation of quartz mineral, which also demonstrating that the a-bromo-saturated fatty acids (a-BFAs) are new selective collectors for reverse flotation to remove quartz mineral from iron ores at a relatively low temperature.INTRODUCTIONThe requirement of higher pulp temperature to maintain the activity of fatty acid anionic collectors which have been widely applied in technological process of iron ores reverse flotation lead to a great deal of energy consumption.The purpose of this paper is to synthesize a new modified collector with carbon chains from eight to fourteen atoms, with strong electronegativity bromine atom introduced into a-carbon position to improve the activity and solubility of the reagent so that it can be adopted at a comparatively low pulp temperature. The collecting performances of these new collectors on quartz surface were studied, and the structure - properties were discussed in light of zeta potential measurements and quantum chemistry calculations."

Jan 1, 2016

By P. Diehl, M. David

"As shortage in the supply of mineral commodities become more probable, there is an increasing need for reliable and comparable reserve/resource data. It is therefore necessary to standardize the traditional classification procedure by quantifying the three basic criteria in resource evaluation: economic feasibility, geologic assurance and recovery. For the portion of fairly well documented deposits and as far as their geologic parameters are concerned, geostatistical methods can considerably improve the quality of ore classification. In respect of economic feasibility and recovery, approved geostatistical methods can be introduced directly into the classification procedure. The concept of geologic assurance, however, requires a new interpretation in terms of geostatistical error spread. As the ""risk"" in estimating an ore parameter is also a function of the respective block size, it is reasonable to define not only upper limits for the risk intervals for each class of uncertainty, but also block dimensions which reflect the typical stage of planning associated with the different ore categories. An algorithm has been developed to block out areas inside a mine or a large panel which satisfies the constraints of an ore category in respect of the risk intervals of a parameter and in respect of their size. The method has been computerized and is demonstrated on a massive copper-nickel deposit.IntroductionFacing an uncertain future with respect to the demand and supply of mineral commodities, both governmental authorities and the mining industries show an increasing interest in a useful framework for the assessment and classification of the remaining mineral resources"". This is reflected by the recently published appraisal and classification scheme of the United Nations as well as by the new or revised classification systems of the USA; Canada or Australia. Moreover there are various classification schemes which are currently discussed in major mining companies."

Jan 1, 1982

By M. Drozd, A. Ibrado, P. Butcher

While effective in treating refractory sulfide ores, pressure oxidation leaves carbonaceous matter unscathed and able to adsorb gold from cyanide solutions. Barrick Goldstrike&apos;s strategy to mitigate this problem is to minimize contact between dissolved gold and native carbon in advance of the carbon-in-leach (CIL) process. Measures currently in use include limiting carbonaceous matter in the plant feed by meticulous blending of ore, controlling the degree of oxidation in the autoclaves and blinding native carbon surfaces with lauryl sulfate. The presence of residual cyanide and thiocyanate in the process water remains to be a cause of premature gold dissolution and loss of gold by adsorption on carbonaceous matter. This cyanide is introduced by water that is recycled from the tailing pond. Of several treatment options considered, oxidation by peroxymonosulfuric acid, also known as Caro&apos;s acid, is deemed to be the most effective. Laboratory and pilot plant tests show that Caro&apos;s acid can oxidize free cyanide, weak¬acid-dissociable (WAD) cyanide and thiocyanate, resulting in significant improvements in gold recovery downstream. The process requires Caro&apos;s acid at 125 % of the stoichiometric requirement and pH in the range of 9.5 to 10 to accomplish the desired destruction in about twenty minutes. A cyanide destruction plant is currently being designed and construction should be completed by the end of 2005.

Jan 1, 2005

By M. U. Savich

In Canadian mines, ear muffs are now an essential part of safety equipment. Because of this, a research study was conducted to investigate their efficiency. The main characteristics of eleven commercially available ear muffs were investigated in the laboratory and analyzed by: (I) a psychophysical method; and (2) a physical method. These investigations showed the following effects: head size has a significant influence on the attenuation because of a different clamping force; the amount of hair trapped between the ear muff cushion and the head decreased ear muff attenuation; attenuation and comfort are not in a causal relationship; with the use of glasses and their adapters, attenuation decreases-the adapters are not effective sound barriers; there are no great differences in attenuation with neck movement; the efficiencies of various brands of ear muffs are not equal; ear muffs with a small cushion area start serving their purpose more quickly because the force per unit area is larger; a clamping force larger than 900 g wt, in most ear muffs, does not cause an increase in attenuation; attenuation characteristics (ANSI 224.22 - 1957) of ear muffs show some correlation with physical tests. Nine ear muffs out of the eleven were tested under uniform conditions in mines. Three ear muffs were found to be the best. All three ear muff s have bands passing behind the head. The ear muff with a support strap, which improves comfort and maintains a good fit during wear, showed the best attenuation. Causes of poor attenuation are numerous: bad mounting of ear muffs on helmets, improper fitting, interferency by hair and glasses, improper wearing by miners, unsatisfactory enforcement by supervisory personnel, incomplete training of miners, etc. Results of this research have indicated that none of the ear muff s tested in this study contain all of the characteristics desirable in an ideal unit. Because of unsatisfactory ear muff attenuation in working conditions (/5 dBA), it should be a mandatory requirement that workers wear both ear muff s and ear plugs if the noise level is higher than 105 dBA (various literature recommends t io dBA). The key to the solution lies in the following: the foreman must be capable of helping and controlling miners in their task of wearing ear muffs properly; the program must be introduced to miners; and constant contact must be maintained with manufacturers.

Jan 1, 1979

By T. S. Golosinski

"This paper reviews the types of selective continuous miners (SCMs) available at present, and compares their main features. Furthermore, operating practices and mine planning aspects of the SCMs applications are reviewed and conditions for efficient application of this equipment are defined. Finally, the potential applications of the SCMs in surf ace mining of oil sands are discussed INTRODUCTIONIn the 1970s the United States Bureau of Mines (USBM) conducted a program of investigations, design and demonstration of various continuous surface mining concepts, This included continuous mining equipment which was an adaptation of several civil engineering and/or underground mining machinery concepts to surface mining. Upon termination of this program, the related development was continued by a number of equipment manufacturers, leading to development of several types of SCMs. This new type of surface mining equipment is able to mine selectively hard and thin multi-layered formations at high, sustained, and economically viable production rates.While used mostly in coal mining at present, the characteristic features of this equipment permit conclusion that it may prove to be an efficient tool for surface mining of oil sand, and/or related overburden stripping. Of particular interest here may be the ability to mine thin layers of hard material, without a need for its earlier fragmentation, and the ability of the SCMs to load a variety of haulage equipment, including belt conveyors."

Jan 1, 1989