Search Documents

By H. E. Lake

VERY EARLY in the initial stages of underground development work at Eldorado's Beaverlodge operation, the decision was made to use mill tailings as a backfill product. Mining and milling commenced in June, 1953, using locally available sand as backfill, while test work and installation of a plant was carried out to prepare ?and deliver the tailings to the mining areas. The first use of tailings was made in February, 1954, a sandslime separation being carried out with hydraulic cyclones. To date (January. 1956), approximately l 40,000 tons of fill have been used in the stoping areas, providing very effective support in a 50 deg. Vein system of cut-and-fill mining. The recoverable portion of the mill tailings amounts to 40 to 45 per cent, which has resulted in a product giving a percolation rate of 6 to 10 inches per hour. Owing to the fact that Eldorado has milled from 15 to 2 5 per cent more ore than it has mined, through the purchase of custom ore, the degree of control on the sand-slime separation has not been as critical as it might normally be when the filling operation must depend only on the tailings from ore mined. A description of the conditions involved and of the plant as finally installed is given below. It might be mentioned here that, with the impending increase in milling capacity from 700 tons to 2,000 tons p.er day, the present plant will be considerably altered within the ensuing year to handle the increased tonnage and distribution.

Jan 1, 1956

By T. S. Smith

INTRODUCTION IN PREPARING this paper for the District 4 Meeting, three factors had to be considered. First, the paper must fit the time alloted; second, it must give a general picture of the geology for those unfamiliar with the property; and third, it must contain some new material in order to be of interest to local delegates. The most comprehensive extant discussion of the geology of the property of McKenzie Red Lake Gold Mines, Limited, is contained in Horwood's report on the general Red Lake area ( 1). This report is the 'bible' of the area, and a general paper on the geology of this particular mine would almost certainly appear to be a condensation of it. It was thought, therefore, that the most suitable procedure would be to base the general outline on Horwood' s report, to extend that outline where possible from information gained since its publication, and finally to leave dangling for the contemplative geologist some of the ideas and problems which ?are currently under consideration. LOCATION AND HISTORY The property of McKenzie Red Lake Gold Mines, Limited, is in Dome township, in the Red Lake mining division of northwestern Ontario. The mine is on McKenzie Island, about four miles north, by water, of the Hasaga mine and old Howey mine.

Jan 1, 1951

By A. J. Reed, W. R. Bergey, Carr. J. M.

"The Highmont copper-molybdenum deposits are at Gnawed Mountain in the Highland Valley porphyry copper district, 125 miles northeast of Vancouver. This district is near the center of the lower Jurassic Guichon Batholith, where a north-trending swarm of porphyry dikes is crossed by west-northwesterly structural belts in which fracturing, intrusion of porphyry and breccia, and mineralization areconcentrated.The Highmont deposits are 2 miles southeast of, and in the same southernmost structural belt as, the Lornex deposit. The main deposits occur on either side of a composite dike of granodiorite, porphyry and breccia which strikes west-northwestward in fractured quartz diorite. North of the dike, the adjacent Nos. 1 (East) and 2 (West) zones together contain 150 million tons of open-pit ore mineable in two separate pits. These two zones will support a 25,000-tpd mill with a grade in the first five years of approximately 0.46 per cent copper equivalent. South of the dike, the Nos. 3 and 4 zones are partly explored and will provide large additional reserves. In these various zones, chalcopyrite, bornite and molybdenite form disseminations and fracture-fillings accompanied by quartz, K-feldspar, tourmaline, sericite, specular hematite and other minerals. Bornite extends for varying distances north of the dike, beyond which chalcopyrite is locally accompanied by pyrite. Higher-grade mineralization tends to coincide with fracture swarms, or with shear zones and faults which largely parallel these swarms. The ore zones are reflected by geochemical soil anomalies which show some glacial dispersion. LP. surveys gave weak but significant responses, expressed as per cent frequency effect. The ore zones occur within a strong magnetic gradient, but do not show a significant magnetic response."

Jan 1, 1971

By L. J. Cunningham

I THINK it can be safely said that no mining operation, whetl1er open-pit or underground, is ever entirely free of water. It follows that every ton of ore bears a charge which represents, either directly or indirectly, the cost of keeping the mine workings as dry as possible. Water problems occur in all phases of mining operations. They cause difficult and costly drilling conditions during the exploration stage, they often seriously delay mine development, they can slow mine production and reduce efficiency, and they are a continued burden over the life of the mine. It is therefore in the interest of all mining men to be familiar with the methods and materials used for grouting. The most common grouting material is cement. Cement grouting is old and well established, and many engineers are familiar with its uses and limitations. The technique of cement grouting is relatively simple and fairly well understood, and the materials utilized are relatively in-

Jan 1, 1962

By C. O. Stee

Introduction The property of Siscoe Gold Mines, Limited, is located on an island of three hundred and forty acres in lake Kienawisik, about fifty-two miles east of Noranda and forty-three miles south of Amos, Quebec. Lake Kienawisik is a part of the Harricanaw drainage system and is crossed by the main line of the Canadian National railway at Amos. This waterway is navigable for boats with a draught of six to eight feet. Diesel engines have been the source of power at the property since milling operations were commenced in January, 1929. The power plant as first designed and built was for a milling capacity of 100 tons. Two Polar-Atlas units, each of 200 h. p., comprised the original installation. With the growth of the 'mine, more engines were added until, at the present time, there is installed at the Siscoe what is rated the largest Diesel plant at any mining property in Canada. Definition of a Diesel 'The Diesel engine is an internal combustion engine which works with liquid fuel introduced after, and independently of, the air charge at a time when communication between the cylinder and the outside atmosphere is cut off, and which ignites the fuel by compression-beat and stored combustion-heat unassisted by heat sources outside the cylinder itself while the engine is in stable operating condition"(1).

Jan 1, 1934

By G. C. Mackenzie

At the last Annual Meeting of the Institute, Dr. C. V. Corless sketched the potential mineral wealth of Canada so clearly, graphically and with-all so entertainingly that one's imagination was fired with the promise held out to future generations for the tremendous expansion of the mining industry in the Dominion. Posterity will undoubtedly witness the fruit of much of the geographical search and survey that is now carried on by our government mining departments. Year after year the work advances, slowly but surely, new areas are . explored, older areas are surveyed in detail, the information being compiled in maps and reports of incalculable value to the prospector, the engineer and the general public. The immensity of the task of exploring, geologically, the outlying portions of the country, with the ultimate view of making valuable mineral discoveries, may be visualized from a study of Dr. Corless' paper and the subsequent discussion which took place and one becomes impressed with the fact that three-quarters or more of the problem can be included under the word "transportation". For instance Dr. Corless said, "The few geological explorers who have penetrated to these remoter regions . . . . . . have as a rule been compelled to stick closely to canoe routes,"; Dr. Goodwin remarked, "This barren Laurentian granite, which is put down on the maps as covering the greater part of this area, is the best guess the geologist could make from travelling along watercourses Within the next few years . . . . . . the Timiskaming and Northern Ontario railway will undoubtedly be extended to James Bay . . . . . . In order that we may be prepared for the probable influx of prospectors when transportation facilities to tidewater are provided, I think all available information on this district should be gathered together in handy form." All three-Corless, Goodwin and Cole-emphasize the well-known fact that explorers, geologists and prospectors working in new country must stick to the watercourses and that transportation by rail, road or water has always been the all-important deciding factor in facilitating the exploration and development of remote districts. Dr. Corless did, however, suggest other means of transportation in stating, "The aeroplane will be of assistance in future study of some parts of these remote areas."

Jan 1, 1924

By A. O. Sfriso

"Numerical modelling is becoming universal in rock engineering practice. Most applications focus on the prediction of failure loads of 2D problems, where the numerical models are useful extensions to analytical methods and experience-based design criteria. For 3D problems and problems where the assessment of serviceability indicators – displacements, ground-structure response, etc. – are of importance, the selection of the constitutive models themselves and the implications of the selection of material parameters may have a very heavy impact on the reliability of the model outcome and its predictive capability.This paper overviews basic common aspects of constitutive equations used in practical rock engineering and summarizes some challenges that are frequently observed when reviewing numerical models performed for routine problems in rock engineering. INTRODUCTIONNumerical methodsFrom a philosophical perspective models, either analytical or numerical, are idealizations of a perceived reality. For us engineers, models are just tools we use to guide our judgement and understanding of the problem in hand. When dealing with problems in rock engineering, we resort to a wide range of techniques:1. Closed form solutions like confinement-convergence methods for circular tunnels: these methods satisfy equilibrium and compatibility requirements at the cost of a crude simplification of the material behavior and geometry;2. Limit analysis methods, like bearing capacity formulas: lower bound methods satisfy equilibrium but sacrifice compatibility, and upper bound methods do the opposite. Material behavior must be simple, geometry admits limited freedom;3. Limit equilibrium methods, like method of slices for slope stability: they satisfy restricted forms of equilibrium, do not satisfy compatibility requirements, require simple material behavior but have a much greater flexibility on geometry;4. Numerical methods, where a mesh is employed to discretize the problem geometry: when properly formulated, these methods satisfy equilibrium and compatibility requirements and give reasonable approximations to the behavior of very complex geometries and construction sequences. Very little restrictions remain on geometry and material behavior, but the cost of calibrating the material parameters can be very high."

Jan 1, 2015

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, I. M. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite ore by a pressure acid leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project. The Ambatovy orebody is located in Madagascar. The mini pilot plant testwork was carried out in the Dynatec metallurgical laboratory in Fort Saskatchewan, Alberta. The results of the testwork were very encouraging, including nickel and cobalt extractions in the range of 95.5% to 97.0%, and 94.0% to 97.0%, respectively, in the ore leach step with sulphuric acid. High recoveries of nickel and cobalt were achieved throughout the remaining process steps, yielding separate nickel and cobalt metal powders with better than acceptable purity.

Jan 1, 2005

By T. N. MacAuley

"The Ingerbelle and Copper Mountain deposits are located near Princeton in southern British Columbia. They are owned by Newmont Mining Corporation's wholly owned subsidiary, Similkameen Mining Company Ltd. The property includes the Copper Mountain mine, a former producer. Ore reserves recoverable by open-pit mining are estimated to be 76 million tons containing 0.53% copper. Production commenced during 1972 at a rate in excess of designed capacity (15,000 tpd). All of the known major copper deposits in this area lie in a 14,000- by 3,500-foot belt of Triassic volcanics (Nicola Group) that is situated between a well-defined syenitemonzonite- diorite stock on the south and a variable intrusive complex on the north. The Nicola rocks consist of andesitic tuffs and agglomerates with lesser amounts of flows and some lensy siltstone layers. The orebodies are essentially disseminated sulphide deposits, although fracture-fillings are also important in many areas. Total sulphide content is usually less than 5%. At lngerbelle, and at Pit 2 and most of Pit 1 at Copper Mountain, the sulphides are chalcopyrite-pyrite. In part of Pit 1 and most of the former underground mine they are chalcopyrite-bornite. At lngerbelle the predominant alteration associated with mineralization is a pale greenish-gray bleaching of the dark andesitic rocks. This has been identified as albitization, with lesser amounts of epidote, chlorite, biotite, scapolite and calcite. This bleaching is plentiful at Pit 2, but K-feldspathization is also evident here. These orebodies can better be classified with pyrometasomatic deposits than with typical porphyry coppers. Their relationship to intrusives, the probably extensive metasomatic replacements, the evidence of pneumatolytic activity, the formation and redistribution of magnetite, and the irregular distribution of mineralization are all characteristic of this class. Deep-seated faults probably acted as channelways for mineralization; fracturing, faulting and rock contacts influenced ore localization in detail."

Jan 1, 1973

By R. E. Ray

"As real estate for new development in urban settings becomes scarce, commercial high rises are being constructed above open passenger rail tracks and vehicular roadways. Rail and roadway overbuilds are treated as tunnels requiring emergency ventilation systems for train or automobile and truck fires. The value of floor space in residential and office towers poses challenges to engineers responsible for designing fan rooms and shafts for tunnel ventilation systems within the towers. This paper describes a case study of the unique incorporation of tunnel ventilation fan plants in the overbuild structure of a passenger railyard and an adjacent roadway.INTRODUCTIONTunnel ventilation systems are required for passenger rail and transit (subway) tunnels by the NFPA 130 Standard for Fixed Guideway Transit and Passenger Rail Systems, and the NFPA 502 Standard for Road Tunnels, Bridges, and Other Limited Access Highways requires tunnel ventilation systems for vehicular (road) tunnels. Passenger rail and transit (subway) tunnels are typically ventilated with a series of shafts placed longitudinally along the tunnels to provide piston relief for normal train operations and emergency ventilation of train fires utilizing reversible axial flow fans. The shafts are incorporated in dedicated ventilation buildings that house the tunnel ventilation fans and starters, switchgear to power the fans and other equipment and systems in the building, Programmable Logic Controllers (PLCs) to control fan operation with Supervisory Control and Data Acquisition (SCADA) software, and HVAC fans and ductwork to ventilate the spaces in the building. These ventilation buildings may also provide access to the tunnels below with ingress/egress stairs for use by first responders and firefighters entering the tunnels and train or transit system passengers exiting the tunnels in an emergency. A photograph of a passenger rail ventilation building that encompasses four tunnels is shown in Figure 1."

Jan 1, 2019

"A method is described for determining the viability of hard rock orebody extraction by block caving. Using a very limited amount of geotechnical data, the procedure enhances Laubscher’s empirical stability graph method by using the complex structural modelling system (ChaSM) to assess cavability and block cave tonnages.IntroductionIn considering the selection of suitable mining methods, block caving has gained popularity over other extraction systems in recent years (Butcher, 1999). This has been ascribed to the fact that block caving is the lowest cost per ton mining method, with orebodies that were in the past considered unsuitable for caving, now being successfully mined. However, even though all orebodies will cave, a problem exists in the evaluation of economic viability — it is necessary to be able to predict both when the orebody will cave and what will be the sizes of the initial ore fragments (and the associated tonnages) that report to the drawpoints. This problem is compounded by the fact that, during the scoping study phase of a project, only limited geotechnical data may exist on which to base an assessment of whether block caving is viable or not. Empirical and numerical methods of cavability assessment do not account for the full effects of geological discontinuity trace lengths, nor for the stress regime. Those require significant geotechnical data to be available. The result is that uncertainty may exist as to whether block caving is an economic option. This uncertainty is complicated by the fact that limited experience exists with the caving of more competent orebodies.This paper describes a method for assessing cavability, and for predicting the size of initial ore fragments and the tonnages reporting to block cave drawpoints, using only the level of data normally available during a scoping study. Fragment size and tonnages are assessed by identifying potentially unstable blocks and wedges in the undercut back using statistical joint data. The effects of lateral confining stresses are accounted for by comparing the in situ stress orientations with the joint orientations. To evaluate the accuracy of the method, a back analysis exercise was conducted to predict cavability and initial tonnage for a mine in which the actual behaviour is known. The method is then applied to cavability and tonnage predictions for a hard rock orebody."

Jan 1, 2002

By Glenn Davis

In the world of large scale open pit mining, the majority of a mines operating cost is tied to the removal and transportation of the overburden waste material. Typically, many large haul trucks are employed to transport this overburden from each excavating face. The trucks transfer the waste material from deep within the pit to waste dumps on the surface incurring significant costs in operators, road construction and maintenance, vehicle maintenance staff and support facilities, fuel, tires, and spare parts, as well as the capital cost of the truck fleet itself. In addition, the haulage of the actual mined material carries similar operational costs. In both cases, these costs grow as the mine face advances and pit haulage distances increase. Reducing truck haulage is one key to the success of the Dual Truck Mobile Sizer (DTMS). Being the world?s first fully mobile truck dump station, transportation costs can be significantly reduced as the mine face advances. Furthermore, when used in conjunction with a shiftable face conveyor and a mobile overland hopper, substantial cost savings can be achieved. The mobility of the system allows for the considerable reduction in the haul truck fleet. Overall mine site emissions levels are greatly reduced by the fleet elimination, as well as keeping the majority of the hauls on a flat grade within the pit. Emission levels on a typical truck will dramatically spike as the angle and the length of the haul are increased. Moreover, comparing diesel engines versus electric powered conveyors to move the material contributes to the realized savings.

May 1, 2010

By A. C. A. Howe, J. C. Rowntree

"The Bernie Lake pegmatite near Lac Du Bonnet in southern Manitoba is a complexly zoned pegmatite containing several lithium-bearing units in addition to the western world's largest known reserve of cesium. The pegmatite forms a flat-lying ellipsoidal body within an east-west-trending Precambrian amphibolite. The pegmatite enclosed by this vertically schistose amphibolite lies near the eastern tip of a granitic intrusive. The relationship of this intrusive to the pegmatite is obscured by Bernie lake. To date, the pegmatite body has been delineated aver an area of approximately 80 acres; it attains a maximum thickness of 280 feet. Several distinct zones, including three assemblages of economic importance, comprise the pegmatite itself. The combined spodumene and lepidolite assemblages provide a recoverable defined lithium ore reserve of almost 5 million tons averaging more than 2 per cent lithium oxide. The recoverable cesium ore of the pollucite assemblage provides 300,000 tons averaging more than 20 per cent cesium oxide; this represents more than half of the western world's pollucite reserve. The Bernie Lake pegmatite deposit, owned by Chemalloy Minerals Limited, is well located with respect to the growing United States markets, and its reserves of cesium are large enough to enable it, under favourable economic circumstances, to become the major producer of this metal in North America."

Jan 1, 1967

By H. P. Kang, Y. J. Feng

The hard roof in underground coal mines is generally considered as a main cause that induces disasters in working faces and entries, such as rock burst and windblast. Hydraulic fracturing technology is an effective approach to weaken hard roof to reduce ground pressure and control rock burst. The state and achievements associated with hydraulic fracturing technology applied in Chinese coal mines are summarized in this paper. Theories related to hydraulic fracturing are of the essence in fracture design to determine the fracture initiation and propagation pressure and predict the geometry and the characteristics of hydraulically induced fractures. Initially, theory of elasticity was employed to determine the breakdown pressure for a vertical borehole where the rock medium is assumed to be elastic. However, porosity and pore fluid have an influence on the borehole breakdown pressure, and then the poroelasticity theory was applied. Arbitrary deviated boreholes in practice are rather common and the maximum tensile stress criterion was employed to determine borehole breakdown pressure. The effect of natural crack in the rock medium on the initiation pressure has been taken into consideration through fracture mechanics. Meanwhile, considerable achievements have been made on hydraulic fracturing tools and equipment, and a set of mature hydraulic fracturing technologies for hard roof control are available. Some comprehensive investigations on the hydraulic fracturing for hard roof weakening are presented, and successful field applications in the Jincheng and Luan coal mining districts are introduced. Finally, the unsolved problems related to hydraulic fracturing are also put forward.

Jan 1, 2015

By P. H. Jennings

Commercial tellurium commonly contains heavy basemetal impurities such as lead, copper, iron, etc., as well as selenium and oxygen. The base metals may be removed by vacuum distillation or by zone melting. Vacuum distillation is a convenient method for treating moderate quantities (~ 100 kg.) for the production of a material having a total content of heavy metals in the 10-30 ppm range. By zone melting, it is possible to lower all the heavy metal impurities tm below the limits of spectrographie detection. Neither vacuum distillation nor zone melting is effective for the removal of selenium, but treatment of molten tellurium with hydrogen converts selenium to hydrogen selenide. This procedure is too s low to be considered except as an adjunct to zone melting. In the course of air-melting, many of the more easily oxidized impurities form a dross and may thus be readily removed. Substantial refinement with respect to iron, tin, chromium, aluminum, sodium, silicon, magnesium, calcium and manganese can be achieved in this way. Although tellurium can be electrodeposited from either acid or alkaline solutions of the dioxide, various factors militate against successful electro-refining, amongst which may be mentioned the brittleness of cast tellurium anodes and the tendency for the metal to be deposited in dendritic form, even at low current densities.

Feb 1, 1966

By P. H. Jennings, J. C. T. Farge

Commercial tellurium commonly contains heavy base-metal impurities such as lead, copper, iron, etc., as well as selenium and oxygen. The base metals may be removed by vacuum distillation or by zone melting. Vacuum distillation is a convenient method for treating moderate quantities ( 100 kg.) for the production of a material having a total content of heavy metals in the 10-30 ppm range. By zone melting, it is possible to lower all the heavy metal impurities tm below the limits of spectrographie detection. Neither vacuum distillation nor zone melting is effective for the removal of selenium, but treatment of molten tellurium with hydrogen converts selenium to hydrogen selenide. This procedure is too slow to be considered except as an adjunct to zone melting. In the course of air-melting, many of the more easily oxidized impurities form a dross and may thus be readily removed. Substantial refinement with respect to iron, tin, chromium, aluminum, sodium, silicon, magnesium, calcium and manganese can be achieved in this way. Although tellurium can be electrodeposited from either acid or alkaline solutions of the dioxide, various factors militate against successful electro-refining, amongst which may be mentioned the brittleness of cast tellurium anodes and the tendency for the metal to be deposited in dendritic form, even at low current densities.

Jan 1, 1966

By Qin-yong Ma, Jing-shuang Zhang, Bo Han, Pu Yuan

In order to improve the utilization rate of blasthole and blasting effect in vertical shafts, 5 kinds of millisecond blasting model tests with three circle vertical blastholes have been conducted in various delay times with concrete as model material. The blasting effects of millisecond blasting model tests are investigated from cutting volume, cutting depth, and blasting fragmentation, then a reasonable delay time is obtained. In the middle of concrete model, there are 4 blastholes uniformly distributed in the first circle, 6 blastholes uniformly distributed in the second circle, and 10 blastholes uniformly distributed in the third circle. Each blasthole is charged with one millisecond delay electric detonator, and the rest is blocked with stemming. The depth of blastholes in the first and second circle is 180mm, which is 20mm deeper than those in the third circle. After initiation, the blasting cavity is cleaned up, then the cutting volume and cutting depth are measured. Meanwhile, the blasting fragments are gathered and have analysed by function Rosin-Rammler. The test results show that when the inner two circle blastholes initiated simultaneously and the third circle blastholes initiated with millisecond delay, the reasonable delay time is 50 ms. At this time, the cutting volume and cutting depth of blasting model are 3920 cm3 and 68 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 53.2 mm and 74.6 mm respectively. While when all three circle blastholes initiated with millisecond delay, the reasonable delay time is also 50 ms. At this time, the cutting volume and cutting depth of blasting model are 10705 cm3 and 118 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 51.0 mm and 81.7 mm respectively. The researches indicate that for millisecond blasting with multiturn blastholes, the reasonable blasting scheme is multiturn blastholes initiated in millisecond delay and the reasonable delay time is 50 ms.

Jan 1, 2015

By Carol A. Pilon

"IntroductionRECENTLY, the Saskatchewan Research Council (Saskatoon ) marked the completion of one of its coal-related projects with the publication of the Bibliography and Index of Coal in Saskatchewan and Adjoining Provinces and States, hereafter referred to as the Bibliography and Index of Coal. Over a two-year time period, literature was surveyed and indexed and bibliographic data were compiled using a computer-assisted information retrieval system called FAMULUS. The final publication contains 1150 bibliographic references, which are cross-referenced by six indices.The project was initiated in September 1974, in support of Saskatchewan's Coal Resources Evaluation Program , an ongoing research program sponsored by the Department of Energy, Mines and Resources (Ottawa) and the Province of Saskatchewan. This program places emphasis on such areas of concern as the occurrence of deposits, chemical and physical properties, calculation of reserves and computer-assisted applications for the evaluation of lignite resources in the Province. Attention is also given to aspects of geophysical exploration, mining conditions and economics, by-products and the transporting of lignite. These are the subject areas .covered by the Bibliography and Index of Coal.The over -all objectives of the literature indexing project may be enumerated as follows: (1) to build a specialized resource library by surveying established public and specialized libraries, and commercial data bases; (2) to enter library data into the FAMULUS information retrieval system, to be used to generate bibliographies and indexes, and to retrieve information by the use of specified searching techniques; (3) to make this library data available to interested persons."

Jan 1, 1977

By L. Yuan, J. Qin, J. Xie, Q. D. Qu, Y. P. Liang

"This paper presents key outcomes of a major Asia-Pacific Partnership project between the Commonwealth Scientific and Industrial Research Organisation and Huainan Mining Industry Group Co. Ltd. to develop and demonstrate advanced technologies at Pansan mine, Huainan, China. A comprehensive approach assessed fundamental strata and coal seam methane conditions during mining and optimized mining sequences and coal mine methane capture systems. The project demonstrated a practical approach and procedures for advanced coal and methane co-extraction systems, improved mining safety and efficiency, increased methane capture and use, and reduced fugitive methane emissions.RÉSUMÉ Le présent article donne les principaux résultats d’un grand projet de partenariat Asie- Pacifique entre le CSIRO (Commonwealth Scientific and Industrial Research Organisation) [Organisation de recherche scientifique et industrielle du Commonwealth australien] et le Huainan Mining Industry Group Co. Ltd.; ce projet cherche à développer et à démontrer des technologies avancées à la mine Pansan, à Huainan, en Chine. Une perspective globale a évalué les conditions fondamentales des strates et du méthane dans les couches de charbon durant l’exploitation et a optimisé les séquences d’extraction et les systèmes de captage du méthane dans les mines de charbon. Le projet a permis de démontrer une approche pratique et des procédures pour des systèmes avancés d’extraction conjointe du charbon et du méthane, pour améliorer la sécurité et l’efficacité minières, accroître le captage et l’utilisation du méthane et réduire les émissions fugitives de méthane."

Jan 1, 2015

By G. E. Willey

F OR many years, only one grade of structural steel has been used in volume in Canada. Its characteristics have not been altered appreciably and its long use speaks well for its performance. This standard grade of structural steel may be bought and specified as C.S.A. G40.4 steel or the American equivalent, A.S.T.M. A7. The principal limitations and requirements of this specification are shown in Table I. Within the last five years there has been a growing awareness among the steel producers and steel fabricators that economic forces are at work which make desirable the availability of new and better grades of structural steel. Competition from other materials has increased. The use of concrete bridges and pre-stressed concrete beams is a prime example. New sources of steel from outside the country have become a threat to the Canadian industry and its high cost-price structure. The need for improved properties in the steel, to make possible technologic

Jan 1, 1962