Search Documents

By O. G. Olvera, D. G. Dixon, E. Asselin, L. S. Quiroz

Dissolution rates of chalcopyrite (CuFeS2) were calculated using electrochemical impedance spectroscopy (EIS). The calculated dissolution rate decreased by a factor of 3.2 after the electrode was passivated. The results presented in this work indicate that the reduction of Fe3+ was the rate-controlling step for fresh CuFeS2 electrodes while the transport of cations within the passive film limited the dissolution rate for the passivated electrode. The transfer of cations at the electrode/electrolyte and passive film/electrolyte interfaces did not affect the dissolution rates of the fresh and passivated CuFeS2 electrodes, respectively. The catalytic effect of pyrite (FeS2) on the dissolution of CuFeS2 continued after the passivating treatment. The contact of fresh and passivated CuFeS2 electrodes with different FeS2 particles resulted in increased dissolution rates, due to an increase in the reduction rate of Fe3+.

Jan 1, 2014

By W. van der Merwe

With the gold industry looking to process more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more crucial. This paper compares the two commonly employed "free" cyanide online analysis methods (amperometric and potentiometric end-point silver nitrate titration) with the common site laboratory rhodanine endpoint silver nitrate titration and ion selective electrode methods. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared with these measurements.

Jan 1, 2011

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company's underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

By A Falter

Gyroscopic surveying instruments, which apply the physical law of a gyroscope, are being used for deter-mining the azimuth of lines with a high degree of ac-curacy. In the past ten years, gyro-theodolites have been introduced widely for underground orientation in the mining industry of Russia, Germany and South Africa. Gyroscorpic methods eliminate awkward procedures of conventional shaft plumbing, and provide more safety, excellent control and the highest precision at any point under-ground without interference with hoisting operations. The advantages of gyroscopic orientation in geodetic surveys become obvious in primary and secondary triangulation, in the determination of co-ordinates of single triangulation points, using the method of trigonometric re-section and intersection, and when traversing over long distances or in areas with obstructed view. Other fields of application are found in geophysical surveys and in the orientation of technical objects; e.g. radar stations, relay stations and ballistic missiles.

Jan 1, 1964

By Arthur Grounds

Historical In the course of a paper which is necessarily limited in length, such as the present one, it is obviously impossible to describe in detail the history, development, and present position of coal preparation in Western Europe. Great Britain has been blessed with large deposits of excellent coal of nearly every type, ranging from the high-grade anthracites of South Wales, which are characterised by their very low ash and volatile con-tents, to the superb coking coals of South Wales and Durham -probably the finest in the world -with their low ash and sulphur contents, the latter constituent often well be-low l per cent. Gas coals abound in Lancashire and Yorkshire, while coals from the East Midlands, Northumberland, and Scotland are excellent for steam-raising and other industrial purposes. The excellent quality of these various coals has, in years gone by, ensured ready .sales abroad and it is not surprising, therefore; that methods of coal preparation were largely developed on the Continent in an endeavour to upgrade the inferior fuels found there, so that the prepared product could compete with British coals on the European market.

Jan 1, 1951

By C. E. White

The depletion of higher grade mineral reserves will accelerate the trend toward production from progressively larger and lower grade deposits. The discovery of adequate reserves of leaner ores will require the development of improved exploration techniques with a greater depth range. The principal challenges to the Canadian mining industry are to find the mineral resources required to meet fast growing world demand and to develop mining methods and equipment to ensure production costs which will strengthen our position in export markets in the face of in-creasing world competition. The challenges cannot be met without intensive efforts to attract more technical men to the industry and to improve their training.

Jan 1, 1967

By R. W. Davis

INTRODUCTION CHURCHILL river was named for John Churchill, first Duke of Marl-borough and third Governor of the Hudson's Bay Company, in the latter part of the 17th century, some fifty years after the ill-fated Danish expedition, led by Munck, had abandoned the site of the now famous seaport of Churchill, as a worthless, cold, disease-ridden country. No other attempts were made to explore the interior until the river basin became a part of the grant to the Hudson's Bay Company and began to play its part in furnishing the luxury of fine furs to civilized people as it had furnished the necessities of food and dress for untold centuries to uncivilized natives. This was the sole contribution of the region to the economic life of the country for some two hundred and fifty years, until 1926, when the power site at Island Falls was discovered by engineers seeking a cheap power source to make possible the development of the great ore-body at Flin Flon. DRAINAGE BASIN OF CHURCHILL RIVER The river is some 1,325 miles long. Rising in the headwaters of the Beaver river, in east-central Alberta, it flows in an easterly direction across Saskatchewan and northeasterly across Manitoba to Hudson bay, through a remarkable basin of some 115,500 square miles, only 6,000 square miles less than the area of the British Isles. A journey down this river leads one through three distinct belts of country, each vastly different from the others geologically and in surface characteristics. For the first five hundred miles the river flows through a basin of 36,000 square miles of the great central-plains country, which is covered with fertile soil and carpeted in its southern part with prairie grass, which gradually gives way to the mixed forests of poplar, spruce, birch, and jackpine in the northern and eastern sections: About midway across Saskatchewan, bald-headed knolls and ridges begin to make their appearance as the river meets the western margin of the Canadian Shield. Then, for some seven hundred miles, it passes through country underlain by the pre-Cambrian rocks of the Shield, which continue to within one hundred miles of Hudson bay. Here the character of the country again changes to a low, clay plain underlain by sandstone, and through this 'clay belt' the river flows between steep clay banks, to empty into Hudson bay.

Jan 1, 1935

By F. Bélanger, P. A. Fournier

"Modelling and optimization techniques used in the operation of the Detour Lake Mine leach circuit are contrasted to a 1973 review of contemporary techniques used by a major gold producer. The leach circuit at the Detour Lake Mine was modelled using a full factorial Design of Experiment of stirred tank reactor leach tests using circuit feed. Contour plots of extraction were applied in the plant to optimize addition rates of cyanide and the newly-commissioned lead nitrate system. Contour plot sections were used to understand the impact of sulphur in circuit feed at different operating dissolved oxygen concentrations. The 1973 review paper offers insight into industrially-applied modelling and optimization techniques. In particular, a mathematical model of plant data was developed using multilinear stepwise regression analysis. The model was presented using graphical representations available at the time and applied to optimize the rates of cyanide addition. Off-the-shelf software solutions of today allow mineral processors to quickly and easily visualize data, allowing them to re-allocate time and resources spent processing data to generating raw data and extracting actionable information.IntroductionModelling and optimization in mineral processing is the art of reducing reality through judicious use of assumptions to understand a process and leverage this knowledge to engineer practical solutions to metallurgical problems. Data analysis is at the core of this enterprise.While this paper showcases the modelling work done at the Detour Lake Mine (DLM), the primary objective is to pause and reflect on how far the field has progressed since the 1970’s. A snapshot of state-of-the-art gold cyanidation modelling at that time is a review paper of the Anglo American Group’s capabilities (Brittan & van Vuuren, 1973). The objective of this paper is not a play-by-play of the evolution of modelling and optimization since that time. Rather, it is a comparison of the field at two points in time.In 2016, DLM undertook an extensive bench-scale leach circuit modelling program to better understand the impact of cyanide, dissolved oxygen, lead nitrate, grind size, density, and pH on gold cyanidation (Fournier, 2016). Two major capital expenditure projects were anticipated for 2017: improvements to oxygen control and a lead nitrate distribution system. While the lead nitrate system was planned for construction, the design parameters had not yet been selected. Following the development of the model, plant trials were executed to validate aspects of the model and the methodology was expanded to address other plant issues, in particular the effect of talc chlorite and pyrrhotite in leach feed.The variables of the bench-scale study are summarized in Table 1. Dependent variables were varied using a full factorial design of experiment with two repetitions for each test condition, yielding a total of 300 tests. Test order was randomized to eliminate bias from independent variables."

Jan 1, 2018

By Jean-François Lagueux

Goldex Mine is an underground mine located near the town of Val-d?Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long hole stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23 Mt of ore, large blasts up to 1.8 Mt are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km radius of the mine site. In addition to managing mass blasts, means must also be found to mitigate the vibrations produced by the blast to diminish the disturbance to the neighbourhood. Therefore, the mine used numerous tools to properly plan the blasts and reduce the impacts. A program to control vibrations was one of the first tools put in place. The program?s aim was to draw up an action plan to ensure a follow-up of the homes by inspecting them. The second tool was to develop a methodology to plot a reliable attenuation curve and to adequately determine the maximum charge weight for each blast. Finally, effective communication tools were developed to inform the neighbourhood. There was a huge amount of work to be done in relation to the bench. Reliable and fast loading techniques had to be found to load large blasts in a very short period of time. Adequate logistics had to be developed to send underground more than 20,000 kg of emulsion per day while performing the daily underground operations. Technology had to be developed to adapt the i-kon electronic blasting system to large blasts. Since the control of the charges was the major factor to reduce surface vibrations, it was important to employ loading techniques that would permit decking of the long holes to reduce the charge weight per delays without adversely affecting the loading. All of this work requires an enormous amount of energy but also close collaboration between the different stakeholders (various departments, suppliers and consultants).

May 1, 2011

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By O. Leuangthong, E. Schnetzler

"The McMurray formation in the Athabasca oil sands deposits of northern Alberta is part of the world’s second largest proven crude oil reserves. The formation is characterized by stratigraphic layers that correspond to three different depositional environments: Marine, Estuarine, and Fluvial facies. Resource estimation for oil sands has traditionally relied on polygonal and inverse distance schemes. These techniques are simple and straightforward in practice, but they do not permit reliable uncertainty assessment. This paper describes the modelling of the McMurray formation using modern geostatistical techniques.Geostatistical modelling should be performed within homogeneous geological facies. The methodology for geostatistical simulation within each of the identified facies involves: 1) assessing the most appropriate stratigraphic transformation for optimization of the correlation structure; 2) determining representative distributions with declustering and debiasing techniques; 3) modelling spatial continuity of the bitumen grade, fines grade, water saturation, and other petrophysical variables; 4) performing estimation and cross validation as checks against simulation results; 5) performing simulation for uncertainty quantification of bitumen and fines grade; and 6) model checking of simulation results against the input data, and comparisons against the kriged models. These steps are described in detail. The application of these models for uncertainty quantification in support of resource classification is also discussed."

Jan 1, 2006

By A. Saigal

A finite element analysis based investigation using DEFORM software was undertaken to model the extrusion of 15% alumina and 15% silicon carbide reinforced aluminum metal matrix composites. The study dealt with predicting the extrusion load as a function of ram displacement and initial billet temperature. The finite element simulation was also used to determine the maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions in the billet during the hot extrusion process. The constitutive equation used was of the type: Z = E exp(Q RT) = A{sinh(ao-)}" where Z is the Zener-Hollman parameter (temperature compensated strain rate), s is the strain rate, Q is the activation energy, R is the gas constant, T is the absolute temperature, a is the flow stress and A, a and n are constants. Based on the work of Davies et al and McQueen and Konopleva, the values of Q (KJ/mol), a (MPa-1), n and A for aluminum 6061 composites reinforced with 15% alumina and 15% silicon carbide used are 181, 0.024, 4.15 and 1.33x10'2 and 233, 0.052, 2.60 and 1.26xl0'4, respectively. Even though the individual parameters are quite different, it was found that the predicted maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions are quite similar and differ by no more than 1-2 percent between the two composites indicating that the deformation behavior is primarily controlled by the matrix material and is not a function of the type of reinforcing ceramic particulates.

Jan 1, 2004

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961

By Bern Klein, Tichang Sun, Daozhen Gong, University of Science and Technology Beijing, Chunbao Sun, Stefan Nadolski

"This paper is focused on the effect of modifying the SAG mill/ball mill transfer size on the energy efficiency of SABC circuits. The transfer size is considered to be a parameter which provides operators with the opportunity to improve comminution circuit performance. In this study, the Moly-Cop tools package was employed to predict the energy consumption of SAG mill and ball mill circuits under different operating conditions. An Energy Benchmarking model was adopted to calculate grinding energy efficiency. The SABC circuit at the Huckleberry mine was selected for this case study. It was observed that after increasing circuit transfer size (T80) from the existing 3.3 mm to 4.8 mm, the Benchmark Energy Factor (BEF) of the SABC circuit decreased from 4.30 to 4.05. In terms of energy consumption of the SABC circuit, 1.17 kWh/t of specific energy saving was achieved through the transfer size optimization.It was also observed that when a transfer size was selected such that both SAG mill and ball mill circuits operated at their highest energy efficient states, the entire SABC circuit was the most energy efficient. The maximum energy efficiencies of these three circuits were all approximately 25% when compared to the minimum practical energy required to carry out an equivalent comminution duty. Single-particle compression breakage testing was used to determine the minimum practical energy associated with the Huckleberry mill feed. In combination with geo-metallurgical data, this study also provides an opportunity to perform dynamic optimization of SABC circuits."

Jan 1, 2016

By Rodrigo Serna-Guerrero, Ted Nuorivaara

"As the demand of raw materials increases in a global scale due to demographic and economical changes, it is necessary to find technological solutions that improve current production processes in an efficient and sustainable manner. The main objective of this preliminary study is to evaluate the properties of foam produced with a cellulose-based molecule as an alterative to commercial frothing agents in flotation operations. There are two potential advantages identified with the use of cellulose-based additives for the proposed application: i) these chemicals can be produced from sustainable sources (i.e., non-edible crops), and ii) cellulose can be functionalized with chemical groups, in order to rationally modify its behaviour. In previous studies dealing with foam stabilization, it has been proposed that some functionalized cellulose species present a self-assembly mechanism at gas-liquid interfaces. Unlike typical surfactant-based frothers, cellulose molecules form networks around the bubbles that act as protective layers to the mechanical stress and to the occurrence of ionic species. This work studied the properties of foams produced in the presence of a partially hydroxylated cellulose molecule (i.e., hydroxypropyl methyl cellulose; HPMC) under various concentrations in a laboratory-scale column. A comparison with a commercial surfactant frother (i.e., Nasfroth 240) is presented, and a rationalization of the behaviour of HPMC in terms of foam properties (i.e., surface tension, bubble size, foam depth) is proposed. INTRODUCTIONThe search for green alternatives to chemicals produced from non-renewable sources has become a topic of major relevance in industry (Choi et al., 2015). As a chemical consuming industry, the mining sector faces now the challenge of adopting new processing technologies and strategies in order to achieve the future demands of sustainability. Evidently, a move towards green chemistry can only take place by identifying substitute molecules offering potential advantages in terms of recovery and grade."

Jan 1, 2016

By William Petruk, J. R. Schnarr

The behaviour of minerals during flotation of a fine-grained pyrite-rich base metal ore was investigated by studying the feeds. concentrate and tailings from every flotation cell in the mill of Brunswick Mining and Smelting Corp. Ltd. Bathurst. New Brunswick. The samples were analyzed for Zn, Pb, Cu. Fe, Ag. Sb, Sn, Bi, In. Hg, Mo and As. Mass balances were computed and recoveries of all metals from each cell. from each circuit and from the mill were calculated. The percentages of sphalerite. galena and chalcopyrite occurring as free grains in each product were determined with an image analyser, as were size analyses for free mineral grains and middling particles, and compared with screen analyses. The results show that the behaviour of minerals is defined much better by the recovery of free mineral grains than by the recovery of elements. The recovery of free sphalerite in the zinc circuit is 96 wt %, whereas Zn recovery from the same circuit is 88 wt %. the difference being due to unliberated sphalerite. The recovery of free sphalerite from the mill feed is 88 wt % and Zn 78 wt %. The recovery of free galenafrom the mill feed is 88 wt % and Pb 64 wt %. The recovery of free chalcopyrite is 75 wt % and Cu 45 wt %. Size analyses show that more sphalerite and chalcopyrite can be liberated by regrinding. but the galena is so fine grained that regrinding would not necessarily improve liberation. Silver occurs mainly in tetrahedrite and galena; the main loss in the tailings is due to large (+ 26 um) and small (-1 um} free and unliberated tetrahedrite grains.

Jan 1, 1981

By Victor A. Sowa

"Abstract - In 1938, a body of goethite and hematite was discovered beneath Steep Rock Lake near Atikokan, northwestern Ontario. This was at the time the largest and richest undeveloped iron ore body in North America. Mining began in 1944, fast-tracked by the needs of World War II, and through 1979 produced 79 Mt of 56.5% Fe. Production required the diversion of the Seine River, draining of Steep Rock Lake, building of a railroad, and a 25-fold increase of the local population. The mining project, at the time, was the largest project of its type undertaken in Canada. The current concepts of sustainable mine development and mine closures have advanced considerably since the period of operation and closure of the Steep Rock mines, and those operations would probably not have met current expectations of sustainability. However, some of the post-closure aspects of the mines provide illustrations of components of sustainability, which could form part of a basis for a post-mining sustainable land use plan. It is concluded that some of these components were successful in meeting current expectations of sustainable use, and although some aspects are unique to the circumstances at the Steep Rock mines, others could be applicable at other mine sites."

Jan 1, 2003

By Donka H. Andreeva

Gold catalysts based on different supports, titania, zirconia, ceria and mesoporous titania and zirconia, nonpromoted and promoted by vanadia in the reaction of complete benzene oxidation have been studied. XRD, HRTEM, TPR, Raman and ESR spectroscopy were applied for the characterization of the catalysts. The influence of gold on the reduction behavior, state and structure of vanadia on the surface was studied, as well as the role of supports nature on the properties and catalytic activity. A strong synergistic effect between gold and vanadia was observed for the all studied catalysts with an exception of the catalysts supported on mesoporous zirconia. In the last case the catalysts containing gold and gold-vanadia exhibit high and equal catalytic activity. The catalysts on ceria show highest and stable catalytic activity in the studied reaction among the all studied catalysts.

Oct 1, 2003

By J. Weyer

"Threshold limit values (TLVs) for NO and NO2 have been reduced drastically in 2016. Emissions of diesel engines have been reduced in the last decades. In many cases this is not enough to stay under required TLVs. Remaining gas in the blasted rock is set free during loading and transport. At the end, only a combination of measures with a further reduction of diesel motor emission, replacement of diesel driven vehicles by electric equipment, new explosives with reduced NO and NO2 production, changes in the organization and effective ventilation measures can ensure that the TLVs are not exceeded. KEYWORDS Blasting fumes, Gas measurement, Gases, Threshold Limit Value (TLV) SHORT HISTORY OF EXTRACTION OF RAW MATERIALS The extraction of raw materials—besides haulage and transport—is one of the main processes in mining and tunneling. The principal objective is the creation of a material which can be transported from the place of extraction (face) to another place for further processing or direct use. Furthermore, recently a desired grain size distribution has become more important. A revolutionary development took place in the course of centuries. With the use of primitive tools like shovels, chisel and iron in the 12th/13th century in Freiberg, ore mines performances of 12 16 cm per man and week could be reached in cross section of 1 m2. Recalculated with an assumed average density, this is a performance of 0.006 t/h. With the introduction of black powder into the subsurface in 1627 by Caspar Weindl in the city of Schemnitz (nowadays Banska Stiavniza), performances increased. A part of the hard extraction work was now done by the explosives. But first in 1767, it was recognized in a mine in Freiberg that more than 1 hole could be drilled (hand-drilling) and blasted. This discovery was so important that a plate with an inscription describes this event. The performance was increased more than 10 times compared to the extraction with chisel and iron. Since this time, drilling and blasting has been the most important innovation force for the increase of the performance. Problems with noxious blasting fumes led to the construction of the first tunneling machine by Henry Joseph Mouse in 1846 (beside shield machines from 1825) (Stack, 1982)). The triumph of mining machines started only interrupted by the two world wars. The development of hard rock boring machines (including roadheaders) was enforced after 1945. An almost complete extraction by hard rock boring machines was predicted for the turn of the millennium. And, indeed, one could find powerful machines in Canadian potash mines which were able to mine 1000 t of potash in 1 hour. That was an increase in the performance by several powers of ten. But already in the 1980s, it was recognized that the ambiguous goal could not be reached. Problems with wear of the tools, radius of curves, minimal length of openings, size and costs of the machines led to a more or less parity between drilling and blasting on one side and machines on the other side, of course depending on the field of use. For this reason, drilling and blasting is still the dominant extraction technology for raw materials. In the development of drilling and blasting technologies, the focus was mainly on the improvement of the safety but also on the increase of the blasting power and performance. Examples are tests for the increase of the power of ANFO explosives which were carried out in the 1970s and 1980s, in the former teaching mine “Reiche Zeche”. In the 1980s vehicles for loading and mixing of ANFO explosives have been developed, the blasting cab sensitivity of ANFO has been increased, emulsion explosives have been developed and up to now further developments like PMMA LOX EX explosives are on the way. At the turn of the millennium, 6 million t/a explosives have been used worldwide. Annual rates of increase of 2% have been predicted (Weyer, 1999). Meanwhile the focus changed from an increase of the performance"

Jan 1, 2019

By G. R. Webber, L. M. Azzaria

"The wide interest in the application of the geochemistry of mercury to mineral exploration is leading to the continued development of a variety of analytical methods for the determination of nanogram quantities of this element. The various methods have different degrees of reliability, sophistication and portability. In this investigation, two simple portable instruments were used in geochemical prospecting surveys -an ultra-violet absorption instrument and a similar one modified with gold for the removal of interfering substances. The results show the application of the method to the determination of mercury in soils of different organic content, and in rocks, sulphides and air."

Jan 1, 1969