Search Documents

By Ike Isagon

Backfilling has become an integral process in underground mining operations, with varying cost-effective forms of application. This study is a part of an overall investigation into the backfill practices at Copper Cliff North Mine (CCNM). The mine is well-diversified in terms of backfill methodologies and practices. The mine employs different fill methods such as cemented and un-cemented rock fill, slag fill, and cemented hydraulic fill (or a combination of them) in order to fill the voids created by mining activities. The history of backfilling at CCNM has been dominated by cemented and un-cemented slag fill. Each fill method requires operating and engineering guidelines for a cost effective quality control system. The purpose of this paper is to briefly discuss the backfill methods and applications, operating guidelines, and engineering requirements at CCNM.

May 1, 2011

By I. Jackman

"Gold is present in different forms and associations in different ores. Flotation is used to recover gold and minerals associated with gold, but the applicability and type of flotation vary. The purpose of flotation in a gold recovery plant is largely dependent on the mineralogical association of the gold, and environmental and economic considerations. In this paper, the role of flotation in the recovery of gold is reviewed. The paper will describe examples of gold recovery by flotation including flotation of native gold, gold associated with sulphides including specifically copper sulphides, gold associated with tellurides, gold ores containing carbonaceous material and gold contained in tailings.INTRODUCTIONFlotation is widely used in the recovery of gold. However, the objectives and the mode of application are quite variable dependent on the type of ore, the gold association(s), other metal values, marketing considerations and environmental requirements. In this paper, a range of different applications of flotation incorporated in the recovery of gold are discussed. The reasons for each particular application are outlined and metallurgical results are presented.The mineralogy of the ore and the gold associations are fundamental influences on gold recovery. The use of flotation to concentrate gold is dictated by the mineralogy of the ore and gold. The fundamental factors are mineral/gold size, liberation size, association of the gold and type of gangue minerals or other valuable minerals. Gold can exhibit a range of sizes in a host from relatively large size (+50 µ) to refractory size (1 µ and sub-micron size). Similarly, the gold can occur in a number of phases in the same host. For example, the gold was present as petzite (AgAu telluride), calaverite (AuTe2) and native gold in a gold telluride ore and each of these minerals was associated with the pyrite host.Understanding the gold mineralogy and association is important in establishing the correct process route. The gold mineralogy is established by good mineralogy, use of diagnostic tools such as diagnostic leaching and assay by size fraction analyses and basic metallurgical testwork."

Jan 1, 1995

By Elizabeth Wademan

Recessions Eventually End ??Companies aggressively cutting production and inventories ??these will come in-line with demand ??U.S. home inventories are declining ??Housing becoming more affordable ??Global trade recovering after collapsing ??Lower oil prices should act as a stimulus Protracted Deleveraging Process Beginning ??Era of leverage-driven consumption is over ??Greatest destruction of consumer wealth since WWII ??Consumers will no longer be able to substitute capital gains for savings ??Shift towards savings will be a headwind to economic growth ???Paradox of Thrift?

May 1, 2009

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

By James Anstey

BHP Billiton?s Cannington facility is a mining and minerals processing plant near Mt. Isa in Central Queensland, Australia, producing silver, lead and zinc. Mine ore is processed in a concentrator, which consists of grinding, flotation, thickening and filtration. Grinding is carried out in a fully autogenous (AG) mill. The mill operates in closed circuit with a pebble crusher. Throughput is approximately 380 tph. Cyclone overflow from the grinding circuit is fed into a flotation circuit for the recovery of lead, zinc and silver. Two concentrates are produced (lead and zinc), which are then thickened and filtered. The filtered concentrate is transported by road to a rail receiving station. From here the concentrate is railed to port in Townsville for shipment to the smelter. Matrikon and Engineers at BHP Billiton?s Cannington Mine have used ProcessACT to develop a flexible, nonlinear dynamic simulator for the grinding circuit to further enhance process understanding, as well to investigate various optimization strategies. An online charge volume estimator was also developed for the AG mill to aid in the understanding of overload conditions, which for the previous two months had been the primary contributor to downtime. The models were developed using a combination of first-principles modeling along with input-output dynamic responses. Examples of models used include: Morrell ?C? model for power and charge shoulder/toe angle prediction; Whiten?s mixing model for breakage and hold-up; Nageswararao cyclone model for predicting cut size; slurry recovery and water recovery. The composite model simulates system dynamics starting from the stockpile reclaim system and finishing at the feed for the flotation process. The objective was to provide a tool that assisted Cannington in understanding their Grinding Circuit and allowed them to develop and evaluate circuit optimization strategies. BHP Billiton Cannington Mine is now considering development of a Grinding Circuit Optimizer utilizing the models developed for the simulator.

Apr 1, 2005

By M. Ounpuu

"Gold, because of low head grade and recovery, is usually of minor importance in the economics of base metal flotation mills. Because of the above little metallurgical attention is usually provided to gold in these mills. But collectively, the gold losses can be significant. For instance, Noranda presently has interest in 13 base metal flotation mills with a collective gold recovery of only 50%. Gold losses are in the order of 150.000 oz per year!The Noranda Technology Centre, in cooperation with Noranda's milling operations, has been investigating the potential of gravity concentration of gold from base metal flotation mills. This paper outlines the pilot and plant testing conducted at three operations with distinctly different ore types; porphyry copper, complex massive sulphide and polymetallic semi-massive sulphide. Testing has been with the Knelson Concentrator which has proven to successfully recover fine gold in a simple, trouble free circuit. Discussion of issues which have risen from the testwork is included. INTRODUCTIONGold, because of low head grade and recovery, is usually of minor importance in the economics of poly-metallic base metal ores. TABLE I presents gold heads and recovery for some of Noranda's base metal mills. It should be noted that the stated recoveries are to payable concentrates, but does not reflect the actual payable gold recovery which in cases is significantly lower. Noranda's average gold recovery into a gold payable concentrates is about 45%. This equates to a collective loss in the order of $57 MM per year of gold"

Jan 1, 1992

By Michel Aubertin

Les digues de retenue de résidus miniers devraient être conçues de façon à supporter les charges les plus défavorables qui puissent être anticipées. Les nombreux incidents survenus au cours des dernières années à travers le monde montrent toutefois que la stabilité de ces ouvrages reste encore problématique. Les cas de rupture les plus courants sont reliés aux glissements le long des pentes, à la liquéfaction des rejets, au débordement des bassins, ainsi qu?à l'érosion régressive et de surface. Après avoir rappelé la nature et l?importance des certains incidents récents, l?origine de ces problèmes est brièvement présentée. On aborde ensuite le lien entre les critères à adopter pour la conception des ouvrages et les risques associés à leur rupture. De nouvelles avenues pour aider à contrôler certains problèmes sont enfin discutées, en mettant l?emphase sur la codisposition des roches stériles dans le parc à résidus miniers.

Nov 1, 2002

By Jean-Claude LeRoy, Herman Keller

"INTRODUCTIONEROCON's work is the reclamation of mine wastelands. It has had considerable experience in particular in the reclamation of gold mine tailings in the Canadian Shield since the latter part of the sixties when most gold mines were closing down.A typical example is the famous Hollinger Mine in Timmins which produced $566 million worth of metal from 1910 to 1968 and had left behind some 56 million tons of tailings covering about 1,000 acres which were reclaimed on very short order and are now lush meadows of agricultural quality.To date, practically all gold mine tailings have been reclaimed once and for all by establishing a permanent, self-sustaining and maintenance free vegetation cover.RECLAMATION & THE MINING TOWNSThe first appreciation of people in a mining community where the tailings have been revegetated will be noticing one day the elimination of dusty conditions that used to arise formerly on every dry and windy day. In that respect, EROCON encourages not only vegetating the tailings but also the immediate surroundings of the mills and plants themselves at active mines. The elimination of windborne dust will result in an appreciable decrease in maintenance costs of plant and machinery and more pleasant working conditions for all."

Jan 1, 1975

Project Schedule ?Construction 2005 ?2008 (3 years) ?Operations mid 2008 ?2020 (12 years) ?Closure 2020 ?2023 (3 years) ?Post-closure monitoring Victor Economic Facts ?$982 million investment; ?$110 million already invested in the Project; ?1100 person years of employment in construction; ?375 full time positions during operations;

May 1, 2006

By J. K. Gowans

"INTRODUCTIONTo bring a mining property into production in the Canadian High Arctic a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these factors, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco's previous experience gained at the Black Angel Mine on Greenland's west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during this small ''shipping window."" The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months production was gained by opting for the ""Barge"" approach.What the Arctic winters do to the shipping season, so do they affect the productivity and the cost of labour. Construction labour must come from southern Canada. Thus higher transportation costs and higher wage rates, with more overtime and incentives, increase the labour costs to approximately 50% over normal southern rates. Couple these rates with the lower productivity involved with men working in the extreme cold temperatures and the net effort is worth avoiding. A process plant being constructed in Southern Canada can take advantage of more accessible labour at lower costs, increased productivity and a faster construction schedule. The barge concept must still deliver the equipment and materials during the ""shipping window"" but it can in the completed form."

Jan 1, 1983

By B. V. Knelson

"GENTLEMEN:This paper will deal with centrifugal separation - theory and practical, and since the Knelson Concentrator is the only centrifugal concentrator with a properly fluidized bed, this paper will cover the Knelson Concentrator and its technical and structural advances over the last five years. As I am the person with the most experience in this line, I guess I am some kind of an expert; what kind I’m not sure, but some kind.This type of concentrator truly was developed because I’m lazy and I constantly look for easier ways to do things. My experience in the mining industry was very limited but I did realize in looking at placer operations, which is the application where I spring from, that it was tremendously labour intensive and my first reaction that ""my god, there must be some method or way-of handling product in a more efficient (and you can read that as being able to quickly recover very fine particle gold) way than was being shown at that time"". So, the Knelson Concentrator was born - about 6 or 7 years later. Our first attempt was a cone with about the same degree of slope as our present machine and since we had no knowledge of vibration dampening and centrifugal forces at that point, it was just an idea that this should work.Our first run was one of twenty minute duration. We did make that first machine variable speed by a mechanical belt system and we found that at about 240 rpms we were virtually shaking the gravel plant apart that we were attached to. So the first run was twenty minutes and back to the drawing board. However, that first run produced a concentrate so superior to anything we had seen previously, that we knew without any question, we were definately and accurately on the right track."

Jan 1, 1985

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By H. L. Martin

A joint federal-provincial approach in gathering basic information from industry on mine production, concentrator operations and ore reserves, initiated during 1978, is a major step toward the goal of achieving better government-industry communication through a common data base. Information from questionnaires sent out by provincial governments is shared with the federal government; correct interpretation is ensured by mine visits conducted jointly by provincial and federal representatives. Initial focus is on nonferrous metal mines. The federal Department of Energy, Mines and Resources (EMR) is responsible for a national analysis that is aimed at the early detection of worrisome developments-and their reasons-in the flow from resources to reserves and from reserves to supply of these metals. The heart of the national analysis is the annual construction of a "monitoring curve", showing each metal's aggregated mine production as it would decrease over time if no new reserves and production capacity were to be added from the year of analysis. For a given metal, a comparison of monitoring curves from year to year can reveal early signs of supply stagnation. In anyone year, a monitoring curve in conjunction with foreseen needs for Canadian mine output will show the production gap that would have to be filled from reserves and production capacity yet to be developed. The production gaps for copper, nickel, zinc and lead, the four leading base metals mined in Canada, are shown for the 20-year period ahead, in the context of production achieved during the past 20 years. It is shown that reserve levels commensurate with likely future production levels would require that average annual reserve additions during 1978-98 exceed the average annual additions during the preceding 20 years. Reserve levels of all four metals have declined in recent years. A review of significant discoveries in the last five years suggests that this fall in reserves is not the result of a lack of exploration successes, but of stagnation in development for various economic reasons.

Jan 1, 1979

By P. A. Selvadurai

This paper presents the results of a research investigation leading to the development of a technique for the measurement of the surface permeability of Indiana Limestone. The tests are conducted on a cuboidal block of the limestone with a flat surface that can be sealed to create a circular aperture through which water influx can take place. Computational results for Darcy flow are used to interpret the results of the experiments. The water entry area can be moved over the surface area of the block to investigate, quite conveniently, the distribution of permeability across the surface of the limestone block sample.

May 1, 2009

By W. L. Hunter

The preparation of coal for the commercial market is a study both varied and wide, and can be viewed from many angles and in different ways. This short paper can but touch upon the subject and is intended to discuss briefly preparation plants which in some cases would seem to be quite inadequate. The conditions confronting most operators are similar, inasmuch as the existing plants were not built specifically to prepare a product for the market of today, but rather of yesterday. The tremendous strides made in the field of combustion in recent years require that the product be of the highest grade procurable, and in a glutted and somewhat restricted market the buyer may be more pernickety than otherwise. These would appear to be the conditions of today. Where a mine is operated individually, better all-round results seem more readily procurable than in a consolidated effort where so many different conditions are sure to arise demanding cognizance, and in many cases requiring to be incorporated in the scheme of things. In the case of a number of mines being administered to form a central source, that source not having had anything to do with the bringing into being of the institutions over which it presides, we find some of the mines well equipped with facilities to properly screen and load the coal, while in others the facilities are not so good, but are doing their share towards delivering a product that will pass muster and in such quantities that they can be counted on.

Jan 1, 1930

By T. Grammatikopoulos, A. McKen, O. Christiansen

Vanadium mineralization occurs in oxide-rich horizons within layered metagabbro zones of the Sinarsuk deposit, West Greenland. The main oxide minerals are vanadiferous magnetite and ilmenite, comprising 30% to 90% of the rock volume and the ratio of magnetite to ilmenite ranges from 3:2 to 4:1. Ore microscopy shows that magnetite and ilmenite vary between 0.2 mm and 4.5 mm in grain size, but locally they are coarser grained. Grains are subhedral to euhedral and annealed suggesting that they will liberate very well upon grinding. Electron microprobe analyses indicate that magnetite grains are homogeneous and have a vanadium content, in different mineralized samples, ranging from 1.93 wt% to 2.68 wt% equivalent V2O5. Ilmenite hosts abundant and variably sized hematite lamellae, and it has vanadium contents ranging from 0.32 wt% to 0.59 wt% equivalent V2O5. Preliminary beneficiation of two composite bulk samples shows the samples can be beneficiated fairly easily using low-intensity magnetic separation at a coarse grind (106 microns to 600 microns) to yield a vanadiferous magnetite concentrate. The presence of hematite lamellae in ilmenite prevents recovery of a satisfactory ilmenite concentrate. The most likely beneficiation flowsheet would encompass a primary mill (SAG or rod mill), which would grind to about 600 microns, followed by a rougher magnetic separation stage. The rougher magnetic concentrate would be reground in a ball mill until suitable liberation is achieved. The reground material would then be cleaned in further LIMS stages. However, further laboratory testing is required to establish the final beneficiation program. This work demonstrates the value of mineralogical investigation in guiding and explaining the results of beneficiation processes.

Jan 1, 2002

By M. Kalin

"Ecological Engineering and Biological Polishing technology is a decommissioning approach for inactive coal, uranium and base metal operations. To improve acid mine drainage water some fundamental aspects of wetland ecology and sediment microbiology are combined, to provide conditions to allow for biomineralization of the contaminants.This paper summarizes the first records of microbial alkalinity generation in acid mine drainage through the utilisation of the ARUM process. The process requires that the seepage is at pH 4.5 where sulphate reducers utilize sulphate to produce hydrogen sulphide, which in turn precipitates with metals. The pH increase is brought about by alkalinity generating microbes.The ARUM process has been successful in increasing the pH from 2.5 to 7.0. Flow through reactors operated in the laboratory continuously for more than 60 days have removed Ni from 13 mg/L to < 0.01 mg/L. Design parameters are being developed for low flow rates of 5 L/min in a test system receiving seepage from a tailings.1.0 INTRODUCTIONAcid mine drainage associated with mining wastes poses a significant environmental problem. Conventional means to treat acid mine drainage (AMD) use chemical treatment system. Ecological Engineering technology uses natural biological means to curtail and ameliorate AMD during mine operations and at the time of decommissioning. The premise underlying Ecological Engineering technology is that AMD is the result of a natural process enhanced by mining activities. Therefore, in nature, a process providing a natural balance to AMD has to exist, which, when assisted through appropriate means, can counteract the detrimental effects of AMD on the environment. This process is microbial alkalinity generation which is known to occur in wetlands, lake and ocean sediments (Baas Becling et al, 1960)."

Jan 1, 1991

Conventional waste management practices produce two waste streams for the construction of separate disposal facilities. The design of tailings impoundments is usually controlled by physical stability. Waste rock materials offer high shear strength characteristics for waste dump construction, however the hydraulic properties promote oxidation. The problem of oxidation is significantly reduced for tailings due to a fine texture that augments water saturation. Co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retention capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimize acid generation and metal leaching. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures and full depth waste repository. The results of a laboratory program to characterize the physical and hydraulic properties of Comix tailings and waste rock are presented here. Various ratios of tailings were blended with three distinct waste rock materials. The saturated hydraulic conductivity for the Co-mixed materials was found to vary between 2 x 10-7 m/s and 5 x 10-8 m/s depending on blend ratio, waste rock type and compaction. This paper introduces concepts for the co-disposal of tailings with waste rock and evaluates the hydraulic behaviour of a Co-Mix waste system. The potential benefits of Co-Mix are shown for a typical mine.

Nov 1, 2002

By C. H. Dionne, J. A. Holmes, B. J. Huls

"Falconbridge Limited is presently developing flowsheet alternatives for implementation at the Strathcona Mill. The main thrust for change arises from the need to reject more pyrrhotite from the concentrate. To maintain appropriate levels of sulphur in the smelter concentrate, however, enhanced removal of non-sulphide gangue minerals must be realized. This could best be done in the Non-magnetics flotation circuit.Laboratory investigations were followed by an on-stream pilot test at Strathcona. The application of a column cleaner on the Non-magnetics concentrate resulted in significantly lower levels of fine gangue at equivalent sulphides recovery.This paper discusses the laboratory and pilot testing and results, with a focus on piloting. Also included is a discussion of the Strathcona Mill Flowsheet and the role of the Nonmagnetics flotation circuit.INTRODUCTIONFalconbridge Ltd. is currently developing means to reduce atmospheric sulphur dioxide emissions. One alternative is a reduction in the amount of pyrrhotite in Strathcona Mill concentrate, which reports to the smelter. Pyrrhotite in the Falconbridge ores contains an average of 39 percent sulphur and 0.64 percent nickel. By comparison, pentlandite contains an average of 33 percent sulphur and 34 percent nickel.A consequence of the rejection of pyrrhotite is a decrease in the sulphur assay in the remaining concentrate. This decrease causes downstream difficulties in the roasting process. Therefore, the content of non-sulphide gangue in the mill concentrate must also be reduced in order to maintain sulphur grades adequate for roasting. The resulting concentrate will have lower sulphur dioxide emissions while maintaining nickel production."

Jan 1, 1991

By Steve Wilkinson

"""Techniques for coarse-particle beneficiation of some gold ores and methods for determining potential for sorting any gold ore deposit.""With the advent of high speed computers, laser technology end different types of electronic sensing devices, ore sorting machinery has been developed, capable of handling significant tonnage rates while maintaining high level efficiency. Gold ores may be amenable to coarse-particle beneficiation where there exist measurable criteria upon which there can be recognition of auriferous versus barren lumps in the run of mine. Three types of criteria are suitable for sorting and are:i) Photometric - optical variance between ore and waste such as vein ores hosted by barren country rock;ii) Conductivity/Magnetic - based upon the metallic mineral content of ore end waste, and its association with Au, such as found in sulphide/arsenide Au ores,iii) Radtometric - detection of natural gamma activity occurring with uranium-bearirig gold ores.The method for determining the sortability of an ore depositconsists of, at least, three stages:i) Initial stage identification of ore and waste types,mineralogical/petrographical associations,amount of dilution in P.O.M.establishment of any sorting criteria]"

Jan 1, 1985