Search Documents

By J. A. López-Molina, S. García, V. Castellanos-Pedroza

"Grouting aims to reduce the permeability of rock mass below a predetermined value and has been widely used in rock engineering field for a long time. However, the injection procedure needs several empirical decision makings and it is rather difficult to reliably confirm the achievement of improvement, because the grout penetration process is not sufficiently clarified. This investigation proposes a neuronal method of defining spatial distribution of rock hydraulic properties and a fuzzy scheme for estimating their relation with the grout penetration (consumption, localization and filling material). The intelligent method stands as a tool for helping in harmonizing the sealing activities and the medium conditions. The virtual simulation of grouting strategies embraces geology, hydraulic and rock characteristics and the filling process. Important aspects as different pressure injection levels and fracturing systems can be holistically studied using the intelligent environment, resulting in an advantageous, economic, flexible and interactive tool for planning better this critical activity.INTRODUCTION Grouting is a very common method of sealing rock and repairing concrete structures (Butron et al., 2010) and its use in engineering of dam-foundation and tunneling has been documented as very successful (Yang, 2004). Generally speaking, to achieve the closing purpose, boreholes are drilled into the rock mass and grout is injected (under pre-selected pressure) until the fractures around the borehole are filled. The complete filling of these fractures is possible if they are connected to each other in such a way that the remaining water and air can be displaced outside the designed grouting zone (Houlsby, 1990; Kutzner, 1996). Water testing is necessary for evaluating seepage potential and for determining whether grouting is necessary or practical. Regardless of the main reason for the investigations, design of a program for water testing for grouting should consider the type of structure to be built, the geologic conditions at the site and the level of seepage control desired. As information gathered the report must content the fracture openness, number and connectivity, exploratory drill holes orientations, materials situation and a panorama of rock-mass state (quality)."

Jan 1, 2015

By T. Chong, R. Pesalj, B. Marchant, Z. Nikic

"The Mount Polley copper/gold project is located in central British Columbia and is currently being developed by Imperial Metals Corporation. Extensive laboratory and pilot plant testing was required to develop acceptable metallurgy for recovery of both sulphide and oxide copper-gold mineralization. Copper recovery is highly sensitive to oxide copper content of the feed whereas gold is primarily associated with the copper sulphide minerals. A conventional flowsheet where sulphide flotation is followed by sulphidization and oxide scavenging is described. The conventional flowsheet was used in a feasibility study which resulted in a favourable production decision at Mount Polley. Detailed engineering and permitting are in progress.More recently, laboratory and pilot testing of a new flotation reagent, S-6493*, an oxide specific collector, has indicated that improved copper recovery can be accomplished with reduced reagent consumption, including elimination of the sulphidization step, using S-6493 compared with the conventional flowsheet. The comparative metallurgical results using S-6493 and conventional sulphidization methods are presented, from both bench scale and pilot testing. Comparative economics of the conventional flowsheet and that using S-6493 are also presented. Advantages of S-6493 include reduced reagent costs, increased revenues from additional copper recovery, and overall reduction in capital and plant operating costs due to the simplified flowsheet. INTRODUCDONThe Mount Polley copper/gold property is located in Central British Columbia, 56 air kilometres northeast of Williams Lake. The first recorded exploration was in 1964. By 1989, a total of 238 diamond drill holes, totalling 27, 522 meters, was completed to detail reserves on the Mount Polley prospect. A number of drill core composites were submitted, containing a variety of oxide copper levels, for metallurgical flowsheet development. Six bulk samples were collected from surface trenches for additional bench scale testing and for pilot plant testing."

Jan 1, 1991

By R. Jackman, D. Koningen, G. Wilcox

"Gowest Gold Ltd. is in the process of developing the Frankfield East gold deposit located along the largely undeveloped Pipestone fault northeast of Timmins, Ontario. In addition to resource development and environmental permitting work the company has had an ongoing program of metallurgical and engineering studies aimed at evaluating options for processing the Frankfield East ore. Mineralization at the Frankfield project contains arsenopyrite and pyrite as the major sulphide minerals. Bulk flotation of all sulphides results in extremely high gold recovery. However, the gold is almost entirely associated with the arsenopyrite fraction of the ore and is refractory in nature requiring preoxidation treatment. Selective flotation was investigated to recover a gold-arsenopyrite concentrate thereby reducing the mass which would be subjected to further gold processing. As part of this work, a pyrite concentrate low in arsenic content was also recovered that would be suitable as a source of sulphur for a smelter (or other pyrometallurgical facility). Production of separate arsenopyrite and pyrite concentrates is frequently examined but rarely adopted due to the distribution of gold between the two products or the inability to achieve adequate separation. Several flowsheet options were investigated in the study. The best results were achieved following a sequential flotation flowsheet. The flowsheet configuration was key to meeting the targets for the two products. In this paper, the various options investigated are reviewed and the results of the final flowsheet are presented. The overall plan by Gowest was to evaluate all process options to bring the Frankfield East deposit into production. The ability to effectively separate the arsenopyrite and pyrite components in the ore provides Gowest with added opportunities to pursue both short and long term production scenarios."

Jan 1, 2012

By S. E. Daniel

"Due diligence reviews are an essential part of mineral property acquisitions. One of the primary reasons to complete an environmental review prior to exploration property acquisition is to assess the potential environmental liability. It is critical to identify the potential reclamation costs or existing environmental liability associated with the exploration property. A review of the existing condition of the property and its history can allow prioritization of exploration targets and ease future expenditures for historic damages. IntroductionIn Canada and some other jurisdictions, the purchaser of a property is assumed to know, and is (in the absence of deceit or fraud) financially responsible for, what is purchased. A plea of ignorance, at least from the perspective of environmental liability, is not an acceptable excuse to avoid responsibility (Nelson, 1994). Therefore, if an exploration company (for the purposes of this paper, any organization conducting exploration work) purchases a property that has environmental contamination, the new owner is liable for the cost to reclaim the site to an acceptable level. The cost to reclaim the site is the environmental liability. The new owner is responsible for existing environmental liability of the property, even if the exploration company’s personnel were not aware of the problem. In simplest terms, buyers beware. Therefore, in order to protect the exploration company’s interests, the exploration manager should determine the characteristics of the property of interest prior to purchase or other involvement, and exercise due diligence.The term “due diligence” is often used in the mining industry. To ensure clarity, in this paper’s context, the author has chosen to use the following meaning: “… due diligence is used to describe a detailed data review, generally in connection with the purchase or sale of a mineral property, the approval of a large capital expenditure, or the borrowing of a large sum of money” (Smith, 1997).Directors of the exploration company are held liable for the decisions made, unless they have relied in good faith on,“…a written report of the auditor, or a report of a lawyer, accountant, engineer, appraiser, or other person whose profession lends credibility to a statement made by any such person” (OBCA, 1994)."

Jan 1, 2003

By Benjamin A. Allou

La seule production de columbo-tantalite réalisée en Côte d?Ivoire est effectuée dans les éluvions et alluvions du gisement d?Issia, localisé au Centre- Ouest de la Côte d?Ivoire. Même si un lien direct avec les roches granitiques est suspecté, aucune attention particulière n?a été accordée à l?étude de la minéralisation primaire en relation avec l?évolution des granites et des pegmatites associées. Ces granites, qui sont en intrusion dans les roches sédimentaires du Protérozoïque inférieur, comprennent : le granite orienté à deux micas (Lobo), le granite orienté à muscovite dominante (Bitapia) et le granite porphyroïde non orienté à muscovite dominante (Issia). Les résultats de cette étude indiquent que les pegmatites à Nb-Ta-Be-Li sont liées au granite de type Issia. Les observations de terrain et les analyses sur roche totale des granites montrent que: (1) les trois principaux granites de la région sont de type- S et peralumineux dans leur composition, (2) ils ont été formés pendant la période tardi- à post-Éburnéenne, (3) le granite d?Issia fut le dernier à se mettre en place. Les pegmatites liées au granite d?Issia ont été classées en quatre types : Apegmatites stériles; B- pegmatites à Be; C- pegmatites zonées à Nb-Ta-Be; et Dpegmatites zonées à Be-Nb-Ta-Li. Les pegmatites zonées comprennent les zones suivantes: I- zone à aplite; II- zone graphique; III- zone à albite, microcline, béryl et columbo-tantalite; IV - zone à microcline massive; V- zone à quartz. Ces pegmatites présentent une zone d?altération métasomatique externe. La minéralisation de Ta, Nb et Be est liées à la zone III des pegmatites de types C et D, et celle de Li est associée aux greisens qui peuvent être observés n?importe où dans les pegmatites de type D. Les données de terrain et de laboratoire indiquent que le granite d?Issia est la roche parentale des pegmatites à éléments rares de la région. Les pegmatites minéralisées sont distribuées seulement autour du granite d?Issia et les patrons des terres rares des granites et ceux des pegmatites à éléments rares sont très similaires. Les analyses de la composition totale montrent un lien génétique entre le granite d?Issia et les pegmatites à éléments rares. Il est suggéré que les pegmatites ont été formées durant le transport et la cristallisation fractionnée du magma.

May 1, 2003

By J. Keith Haddock

"Introduction The Coal Valley Mine is operated by Luscar Stereo (1977) Ltd. with the Alberta Energy Company having a minority interest. The mine produces 2.0 million tonnes of bituminous thermal coal per year. Deliveries include 1.5 million tonnes to Ontario Hydro and 0.5 million tonnes to the export market via bulk handling facilities on the west coast near Vancouver, B.C. There are a number of mining methods utilized at the mine including open-pit by truck and shovel, strip mining with large draglines and stripping with scrapers. The mine is located 100 km south of Edson, Alberta. Geology The coal measures are concentrated within a 210-metre int~rval of the Paleocene section. The coal seams were originally named by the mining companies in the earliest days of development of the area and these names continue to be used today. Of the five main seams, only three are presently economic to mine based on quality, thickness and depth of cover. These are the Val d'Or, Upper Silkstone and Mynheer. The Coal Valley Mine is located in the structurally deformed foothills area of Alberta and the structure of each mining area is therefore very complex. The general bedding strike is 305 degrees azimuth but major thrust faulting and folding has extensively deformed the natural seams as a closer examination will show. The Mynheer Seam, located at the base of the coal measures, ranges in thickness from 5 m to 10 m and has numerous bentonite and shale partings. Because of inherent geological features, the Mynheer Seam has been subdivided into two zones, the Mynheer 'A' and the Mynheer 'B', and the mining of coal in these zones has necessitated the utilization of distinctly different mining methods. The structural regime of the Mynheer 'A' zone consists of an overturned asymmetrical anticline crest containing a steeply dipping major thrust fault which has raised the seam above the present topographic level. Further extensive shearing and rotation of the coal has resulted in the coal taking a 'pod' shape. The Mynheer 'B' Zone is a continuation to the southeast along strike from the Mynheer 'A' Zone. The bedding dips to the southwest at an average of 12 degrees and is interrupted at the south end by a transverse fault and to the north by its outcrop at the surface."

Jan 1, 1985

By George A. Lawrence, J. C. McHardy

"Field operating experience with an improved flotation mechanism for handling various flotation applications is covered in this paper. Some aspects of designing flotation machines are also presented. Operating data from extensive testing of commercial size equipment under actual plant operating conditions in the following applications is detailed:1. Copper Flotation2. Fine Coal Flotation3. Base Metal Sulfide FlotationDesign features, design improvements, modifications tested, and overall performance data are reviewed. Some mecl1anical performance data as well as metallurgical performance results are presented. Some comparisons with conventional flotation equipment are reported in this paper.Flotation sizing theories are reviewed and an actual equipment selection ex2.mple is presented. Scale-up criteria used for developing large cells are briefly covered.The paper concludes with a brief review of anticipated future flotation equipment design needs. IntroductionThe mining/milling industry is faced with increasing pressure to cut costs while maintaining product quality and indeed, in some instances, expanding production. For copper, nickel, iron, molybdenum, lead and zinc sulphides, coal, phosphate and some other minerals;, flotation remains the primary method of concentration and recovery of the valuable mineral away from the gangue. Cost reduction in flotation can be broadly focused on two areas:1. Flotation Chemicals2. Flotation Equipment"

Jan 1, 1985

By Tarrant Elkington

Underground mine planning practices are typically manual and time consuming and will often produce sub-optimal solutions due to the application of generic rule-of-thumb assumptions or ?tried and tested? choices. The development of computer-automated tools for underground mine planning enable a wide range of scenarios to be considered rapidly in arriving at an optimised solution, subject to input assumptions. We have applied these tools to demonstrate ?optimised? solutions that challenge industry standard practices. Further, we have incorporated grade and price/cost uncertainty into these tools to gain an understanding on how the consideration of uncertainty may further alter strategy selection. Finally, we enable the tools to dynamically adjust cut-off grades in conjunction with the evolution of prices/cost.

May 1, 2010

By Roger M. Jones

This paper comments on developments in bulk shipping which will be of direct interest to those who are considering the shipment of dry bulk minerals out of Nova Scotia by water. Various conveying systems, and the slurry system of loading, are considered, and the role of deep water ports as a catalyst to other industries is stressed.

Jan 1, 1971

By Unal Artan

It is well known in the robotics community that the ability to determine the position of vehicles in real time is a key enabling technology required for automation, traffic management, and to ensure safety in the presence of multiple vehicles. Because of this, the introduction of global positioning systems (GPS) has had a remarkable impact on the surface mining industry, enabling real-time tracking of mobile assets, improved safety, and production optimization. Unfortunately, satellite-based GPS is not available underground. This paper reports on the preliminary results of a study to develop a robust method for globally consistent mapping of large-scale underground mine environments. We believe that this may additionally become the first step towards the development of a novel underground positioning technology. Presented are preliminary results from data collected at two underground mines using an Atlas Copco ST14 LHD machine.

Oct 1, 2009

By V. Thangadurai

The critical problems in commercialization of the present solid oxide fuel cells (SOFCs) and useful electrical and physical properties of IT-SOFCs electrolytes are discussed briefly. The conductivity behavior of the perovskite-type and perovskite-related structure metal oxides are summarized. Perovskite-type La0.9Sr0.10ao.8Mgo.203_8 (LSGM) exhibits high ionic conductivity of 0.1 S/cm at 800 °C. In order to improve the electrical conductivity of LSGM and the In analogue of LSGM, substitutions have been made at the A-and B-sites. Substitution of trivalent La3+ by isovalent Pr3+ in LSGM and La09Sro ilno.sMgo.202.85 (LSIM), yield new mixed conductors. Among the investigated compounds in the present study, La0APro.4Sro.21no sMgo.2028 exhibits the highest total electrical conductivity of 3.2 x 10-5 S/cm at 200 °C in air with the lowest activation energy of 0.44 eV (200-700 °C). LSIM and Pr-substituted LSGM and LSIM perovskites show p-type electronic conductivity in the oxygen partial pressure range 10-5 ? 0.21 atm at 750 °C. The perovskite-type solid solution SrSn1-xFex03 exhibits compositionally driven phase transitions. For example, compound of the composition x = 0 to 0.3 crystallizes in an orthorhombic GdFeO3-like perovskite structure, where as that of x = 0.4-0.9 crystallizes in simple cubic SrTiO3-like, and that of x = 1 in orthorhombic structure. The electrical conductivity of SrSn1_xFex03 increases with the increasing Fe content and reaches a value of about 10-1 S/cm at 25 °C in air for x = 1. Compounds with low Fe content exhibit both ionic and electronic conductivity, while the higher Fe content 0.5) perovskites are electronic conductors over a wide range of oxygen partial pressure of 10-22? 0.21 atm at 750 °C.

Jan 1, 2005

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

By James A. Brown, Marius Botha, Christopher A. Fleming

"The technical and economic feasibility or re-processing hundreds of millions of tons of tailings in a number of historic gold tailings dams in the Witwatersrand area of South Africa is being investigated. The objective is to recover uranium and residual gold from the tailings, as well as to oxidize the sulphides to eliminate long term environmental liabilities associated with acid mine drainage. The tailings from the re-processing plant will be re-deposited in a new area far from urbanization, allowing for the rehabilitation of the real estate currently occupied by these historic tailings.The first step in the process involves a mild-regrind and mild acid leach of the tailings (pH 2.5 to 3.0) to dissolve up to 40% of the uranium. This uranium is recovered directly from the pulp by resin in pulp (RIP) with a strong base resin. The RIP tails are then treated by flotation to recover a rougher pyrite concentrate, and flotation tailings that are discarded. The rougher concentrate is cleaned to produce a final pyrite concentrate and cleaner scavenger tailings, and the pyrite concentrate is oxidized in an autoclave to leach uranium and generate acid. The autoclave discharge is combined with the cleaner scavenger tails, and the acid and ferric ions generated in the autoclave are used to leach more uranium and oxidize more sulphide in the cleaner tails. The product from the concentrate leach circuit is processed by resin in pulp for uranium recovery, followed by neutralization, cyanidation and carbon in pulp for gold recovery.The rougher float tails may be further treated to recover gold that was not recovered in flotation, but which had been liberated from the old dumps by natural oxidation of some of the pyrite over many decades. The float tails would be neutralized and treated by cyanidation and CIL to recover this liberated gold.All parts of the flowsheet have been extensively tested in the laboratory, and the critical elements of flotation, pressure oxidation and resin in pulp have been demonstrated in pilot plants. The results of the hydrometallurgical investigations are presented here."

Jan 1, 2010

By B. Tanda

A process has been developed at Curtin University whereby glycine is used in an alkaline environment to leach gold, silver and copper from their ores, concentrates, process intermediates and wastes. Copper mineralisation investigated includes various oxides, sulfides and native copper. The leach process utilises an oxidising environment such as oxygen. Glycine is a non-toxic, non-volatile, edible, low cost reagent which is produced in large industrial quantities for use in several industries. Glycine and its copper and precious metals complexes are stable over wide pH, Eh and temperature ranges. Other than losses in leach residues, the glycine is recovered and recycled for leaching. Iron dissolution is insignificant in the pregnant leach solution. Iron in pyrite remains unaffected, whereas iron associated with base metal sulfides (e.g. chalcopyrite and bornite) is converted to a readily filterable iron hydroxide. Efficient separation of copper by solvent extraction and conventional electrowinning has been shown to be feasible for a number of organic extractants, whereas gold and silver glycinates adsorb very well onto carbon allowing CIP/CIL/CIC (carbon-in-column) based processes. The process is ideal for ores containing acid-consuming gangue, concentrates with high arsenic or halide contents and for copper-gold ores with significant sulfide mineralisation. The process eliminates many of the problems associated with the processing of copper-gold-silver ores, such as elemental sulfur formation, silica gels, unwanted metal co-dissolution, and jarosite precipitation. The reagents used and process residues are much safer and environmentally benign than conventional process options. The processing technology can be applied to in-situ, heap and vat, or agitated tank leaching at temperatures ranging from ambient to below 100?C at atmospheric pressure and is currently being commercialised. This paper will focus on copper leaching and recovery and iron rejection from a chalcopyrite flotation concentrate.

Jan 1, 2016

By Clifford S. Gibson

A year ago a paper (1) was presented at the Annual Western Meeting of the Institute regarding silicosis in Ontario mines. It described the whole problem as we see it and discussed the means of prevention. The work and aims of the Technical Silicosis Research Committee of the Ontario Mining Association, and of the Committee's field engineer, were fully described also and it is suggested that reference be made to this paper in order to have a better understanding of the observations which are presented now. These observations enlarge upon parts of the dust control measures already discussed and tell of general progress in the past year. They concern fifty properties, the majority of the operating mines, which vary in size from the hopeful prospect to established producers yielding 11,000 tons of ore daily. Most of these are gold mines; a few copper-nickel. The ores range from heavy sulphides to siliceous materials and they are mined by many methods from varying types of deposits. The majority of the latter are steeply dipping and all are found in Precambrian host-rocks. Up to the present, die greatest depth to which mining has penetrated is 6,400 feet.

Jan 1, 1939

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By Stephen J. Roberts

Gold catalysts were prepared on co-precipitated, calcined copper oxide - zinc oxide support by an inverse deposition-precipitation method. These catalysts were characterised by X-ray diffraction (XRD) and temperature-programmed reduction (TPR) and studied for CO oxidation activity at various catalyst calcination temperatures. TPR studies of the support material exhibited a double peak and shift to lower temperatures for the reduction of Cux+ to metallic copper, as opposed to the single reduction peak for pure CuO. This phenomenon is possibly caused by an interaction with the zinc oxide. The addition of gold to the support CuOZnO led to a further shift in copper reducibility to lower temperatures. Gold present in the initial uncalcined catalyst as Au3+ was auto-reduced to Au0 under various calcination temperatures. The Au3+ reduction peak was observed to shift to lower temperatures with increasing calcination temperature. The catalytic activity was found to pass through a minimum value with respect to calcination temperature. Catalysts with both gold in entirely the 3+ or metallic oxidation state were found to exhibit high activity. Furthermore, the catalysts were found to decrease in activity with decreasing Au3+ content up to an intermediate calcination temperature, afterwhich the activity increased sharply. Possibly at higher temperatures, a stronger Au-support interaction is formed, leading to a new active site.

Oct 1, 2003

By A. R. Laplante

Gold recovery early in the flowsheet, typically from the primary grinding circuit, has seen significant advances in the past three years. Some of the advances achieved under the auspices of the AMIRA P420B Gold Processing Technology project are reviewed. The areas covered are gravity-recoverable gold (GRG) characterization, GRG behaviour in classification, gravity recovery simulation and the link between gravity recovery and cyanidation.

Jan 1, 2005

By Serge Ouellet

Résumé Six modèles métriques de remblai cimenté en pâte (RCP) ont été suivis durant 120 jours par l?utilisation de deux méthodes géophysiques non-destructives : la résistivité et la micro-sismique. Les RCP étaient constitués de trois résidus miniers et de deux proportions de ciment (3% et 6% en poids). En parallèle, des cylindres de RCP étaient utilisés pour évaluer périodiquement l?UCS. La résistivité augmentait quasi-linéairement de 28 à 120 jours pour tous les RCP investigués. Des variations de résistivité selon le type de résidu et le pourcentage de ciment ont été observées. Une équation empirique a été dégagée entre l?UCS, la résistivité, le temps, la densité relative et le rapport eau/ciment (E/C). La mesure de la vitesse des ondes de cisaillement a permis de dégager une équation mathématique de type exponentielle qui relie la résistance mécanique sans correction préalable par les paramètres de la recette de RCP. La réalisation de ce projet avait pour but de dégager la meilleure approche non-destructive afin d?estimer la résistance mécanique des remblais en chantier minier. Sur la base des résultats obtenus, les deux méthodes utilisées ont donné des résultats probants afin d?estimer la résistance mécanique et les deux méthodes sont donc à même d?être utilisées en chantier souterrain. Abstract Six scale models of cemented paste backfill (CPB) were followed during a 120 days period using two nondestructive geophysical methods: resistivity and micro-seismic. CPB were made up of three mine tailings and two cement proportion (3% and 6% by weight). In parallel, CPB cylinders were used to periodically evaluate uniaxial compressive strength (UCS). Resistivity was increasing nearly in straight line from day 28 to day 120 for all CPB models. According to the tailing type and cement percentage, resistivity variations were observed. An empirical equation emerged from UCS, resistivity, time, specific gravity of tailings and, water/cement ratio. The use of shearwave velocity allowed to identify a mathematical exponential equation related to mechanical strength without prior correction of the CPB?s formula parameters. The purpose of this project was to identify the best non-destructive approach in order to evaluate the mechanical strength of backfill in a mine site. On the basis of those results, both methods gave conclusive results in order to estimate mechanical strength and both methods can be used in underground operations.

Feb 1, 2008