Search Documents

By Longworth C. R

This paper descrioes a case history of a coal mine which developed un'tahle roof conditions due to mass sliding of the overburden strata on a claystone band within the coal seam. The sliding is believed to have been initiated by stress relief associated with the removal of overburden alongside the entry portal of the underground workings. Once in motion, the roof block was kept moving by bulking due to roof collapse in the normal underground goafing operations. Control measures in the form of an earth and rockfill buttress against the entry portal and a sequential mining plan to create goaf areas alongside the entry portal have been initiated to attempt to limit movement. The operation has been continually monitored and a gradually decreasing pattern of movement is being re, orded.

Jan 1, 1981

A methodology for the fatigue life estimation of load haul dumpers, employed in underground platinum mines, has been developed and applied. This method entails the quantification of operating conditions by means of stress measurements. The measurements are then translated into a fatigue loading factor for a finite element model. The results of this analysis are then used to compare all the critical connections in the structure to detail categories in relevant fatigue codes, and predict a life in operating hours for the vehicle structure. The method was applied on a specific model and the results of this analysis were compared to actual failure occurrences with reasonable accuracy. It is intended that the methodology be embedded into performance specifications and purchasing contracts and that technology transfer to OEMs be achieved. Based on the experience of this project and other similar exercises it is estimated that structural life expectancies may be increased across a typical fleet of trackless mining vehicles (LHDs, drill rigs, utility vehicles, dump trucks) by at least 20 per cent.

Jan 1, 2005

A continuous casting machine, of the Concast curved mould design casting billets in four strands, was commissioned at the Newcastle Works of The Broken Hill Proprietary Co. Ltd., in November, 1967. Quality assessment of early casts from this plant indicated that steel cleanliness was sometimes inferior to that of equival- ent ingot cast steel. Extensive trials to develop a modified deoxidation technique were not successful in improving clean- liness to the desired level. A "contra-flow" gas shroud, to cover the steel stream between the tundish and the mould, was developed, and proved successful in achieving the required levels of product cleanliness. The inclusion content of six grades of steel ranging in carbon content from 0.10 to 0.70 per cent is examined, and an attempt is made to explain theoretically some of the results obtained.

Jan 1, 1972

By Yu AB, Azahari HL

Indonesia has the largest coal reserves in the south-east Asian region. According to estimates from the World Energy Confer- ence, it has reserves of 18 billion mt lignite, 4.4 billion mt sub-bituminous coal and 774 million mt bituminous coal (Wyllie,1988). In recent years, substitution of coal for oil in power plants has been the goal of the Indonesian government since proven deposits of coal are about five times as large as national hydrocarbon reserves and most of Indonesia's power stations are still oil fired. Recently a coal fired power plant has been built in Java Barat, which will have a full capacity of about 3000 MW. It is intended to supply coal for this power plant from Bukit Asam mining area (South Sumatra). Coals from Bukit Asam - which are of the lignite or brown coal type - usually contain considerable moisture . It should be noted that reference to moisture in coal pertains to the total moisture content. This is comprised of what is commonly termed as equilibrium moisture and surface moisture. Surface moisture typically affects combustion process as well as pulveriser performance since it possibly influences the relative ease with which coal may be ground. In practice, the surface moisture produces agglomeration of the fines in the pulverising zone and reduces pulveriser drying capacity because of the inability to remove the fines as quickly as they are produced. This agglomeration has also the same effect as coarse coal during the combustion process because the surface area available for the chemical reaction is reduced, hence the combustion efficiency is also reduced. The influence of the moisture of some coals on their grindability (Hardgrove Grindability Index) has been previously correlated by several authors; some of them will be mentioned later. Those correlations, however, could not be immediately applied to any coal since it is still believed that there are other factors which influence the grindability of the coal, such as type and rank of the coal. The relationship between coal moisture content and its grindability has been investigated by Ellmann and Belter (1955). It was found that, for North Dakota lignites, the grindability varied as the moisture content changed. In Britain, Fitton, Hughes and Hurley (1957) stated that, for Bilsthorpe coal, over a wide range of free moisture content (from air-dried to about 30 per cent moisture), the Hardgrove Grindability Index (HGI) remains virtually unchanged. In addition to that, it was suggested that it would be slightly advantageous to dry the coal below its air-dried moisture content (at temperature ¦ 100¦C) to increase the ease with which coal could be ground, especially for low-volatile coal and high-volatile non-caking coal. Furthermore, it was also concluded that a broad relationship appeared between coal rank and Grindability.

Jan 1, 1993

By H Nikraz, E Jamieson, D Cooling

The use of red sand as fine aggregate in concrete manufacture has been investigated as well as the use of fly ash as a cement replacement. The experimental work consisted of casting various concrete mixes including a control and comparing standard properties. Properties tested included compressive strength, splitting tensile strength, flexural strength, modulus of elasticity, water permeability, chloride diffusion, pH dependence leaching and particle morphology. The results show that the concrete strength is not significantly affected when natural sand is replaced completely with red sand. The durability tests indicated high water permeability and high chloride diffusion due to the porosity of the red sand concrete, likely due to the low slump value. Leaching tests did not exceed New South Wales EPA guidelines.

Jan 1, 2006

By Stitt P. H

This paper provides a brief historical review of the invention of the spiral separator and its adoption into Australian metallurgical practice. The purpose of the review is to demonstrate that spiral development to date appears to have been a largely empirical process, and that the cur- rent resurgence of interest in the spiral, especially in the coal industry, warrants an increased fundamental research effort. Current research work concentrating on empirical modelling is outlined, while some preliminary experimental results of a more fundamental nature are presented and some research of other disciplines interested in particle transport introduced in order to stimulate further work and discussion.

Jan 1, 1988

The methods used by the Anglo American Corporation for analysis of long-term metal markets and prices are described. The principal factors affecting the relationships between production costs and metal prices are analysed. These are firstly the type of market, - speculative or consumer commodity, free market or subject to price control; and secondly the rate of growth of demand for the metal. It is shown that virtually all metals will have relatively low rates of demand growth for the foreseeable future, due to market saturation, increased economisation, substitution and product obsolescence. Metal prices have a clear dependance on production costs, however forecasting future costs is by no means simple; amongst other things, account must be taken of changing exchange rates, inflation rates, and the potential for operating more efficiently. The paper concludes by giving brief assessments of the long-term future for aluminium, copper, zinc, nickel and tin.

Jan 1, 1986

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electro- lyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions. The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was invest- i,ated as a method of optimizing glue additions in the presence of antimony. Scanning electron microscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltammetry measurements showed some correlation between current efficiency and activation polarization potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1984

By Kubo H, Kubita K, Morinara M

A quantitative method for predicting the mechanical properties of zinc alloys is proposed on the basis of the molecular orbital calculation of electronic structures. A new parameter which is the s-orbital energy level, Mk , of alloying elements in zinc was introduced into this method. This Mk parameter correlates with the electronegativity and the atomic radius of elements. The compositional average of this parameter varied linearly with the tensile strength and the hardness of commercial alloys and some alloys developed by Mitsui. This electronic method was very convenient in designing high performance zinc alloys efficiently.

Jan 1, 1993

By Shrivastava P

The iron orebodies of the Pilbara region are formed by supergene enrichment of banded iron formation and rarely do such processes produce orebodies with uniform grade distrib- utions. The orebodies being mined or developed have to be worked to grade/quality constraints imposed by contractual agreement rather than natural characteristics. Hence it is imperative to use a non-biased ore reserve calculation method. The geostatistical study of a typical iron orebody is presented. Emphasised are the geological characteristics of the orebody manifested as a variable grade distribution of iron and impurities; the determination of variogram model; subsequent uses of the model for computation of ore reserves and kriged lock estimates; computation of dispersion variance and conditional simulation of orebody.

Jan 1, 1977

By A Fareth

Constructed between 1885 and 1891, the New Croton Aqueduct (NCA) in New York State is a 50 km long (31 mi) brick-lined tunnel conveying water from the Croton watershed north of New York City to distribution systems in the Bronx and Manhattan. Except at two siphons, the aqueduct operates as an open channel conduit from the New Croton Reservoir downstream 39 km (25 mi) to the Jerome Park Reservoir in the Bronx. The remaining 11 km (6 mi) is operated as a pressurised conduit and includes a major siphon, of circular cross-section, under the Harlem River. The aqueduct has a flow capacity of approximately 1100 million litres of water per day (13 m3/s or 290 million gallons per day) and supplies on average ten per cent of New York CityÆs drinking water. The CityÆs water supply system is operated and maintained by the New York City Department of Environmental Protection (NYCDEP). This paper covers the work done during the three main stages of the program to rehabilitate the entire NCA: inspections, design and rehabilitation. It also includes some of the more interesting structural findings of the original construction as well as documents and drawings from the NYCDEP archives. The rehabilitation program has been underway in phases since 1993, with inspections scheduled to minimise outages, allowing this strategic aqueduct to remain in service during critical seasonal periods. The open channel flow section of the aqueduct in the north is horseshoe shaped, with inside dimensions of 4.1 m (13.6 ft) in width and 4 m (13.5 ft) in height. The pressurised section is 3.7 m (12.3 ft) in diameter, and includes a 90 m (330 ft) deep siphon under the Harlem River. A total of 163 million bricks were used in the construction, enough to build a 48 km (30 mi) wall around Manhattan Island, 3 m (10 ft) thick and 15 m (50 ft) high.Between 1993 and 1997 a series of in-tunnel investigations were performed in the open channel portion of the NCA, consisting of field inspection, non-destructive geophysical testing, and coring of the brick liner. Between November 2004 and September 2005, a major inspection program was conducted to assess the condition of the 11 km (6 mi) long pressurised section and all shafts, headhouses and blow-off structures along the entire 50 km (31 mi) alignment. Inspection methods included using an underwater remote operated vehicle (ROV) equipped with sonar and cameras to inspect the deep siphon, fibre optics examinations of probe holes drilled through and beyond the brick lining, and core holes and geophysical inspections to assess properties of the liner and behind-the-liner materials. A water pressure and test grouting program was conducted to assess methods and expected grout takes for the rehabilitation work in the pressurised sections. The rehabilitation program is anticipated to be completed in 2010.

Jan 1, 2008

Maps of mineral grade used to assess mineral reserves are most commonly generated using one of the many estimation methods available such as inverse distance weighting or ordinary kriging. Most such maps incorporate a degree of spatial smoothing which is an integral part of the averaging process. In deposits with highly variable grade which include many gold deposits, this smoothing can mask the detailed geometry of the mineralization at the economic cutoff grades being considered. In underground mining, a knowledge of this geometry is important in the choice of mining method and thus in the assessment of the minable reserves.The method of conditional simulation in geostatistics can be used to generate maps of grade which reflect the actual spatial variability of grade as measured through the variograms of the drill hole data. Simulated maps can provide a number of equiprobable images of the mineralization geometry from which a more appropriate mining model of the mineralization can be developed. Multiple simulations can also be used to assess the uncertainty existing in the current knowledge of the reserves.

Jan 1, 1990

By Olson H, Kincaid R

The marine portion of the Pacific Basin and Rim constitutes a significant part of the world's surface in which the mineral resources are virtually undeveloped. Indications of substantial resources have resulted in speculation and uncertainty with regard to their potential in the near term. The main issues are centered on the markets for the resource materials, the technology needs for their recovery, and the possible impacts of their development on the environment. While the governments of Japan, France, the Soviet Union, India, China, and Korea are financing new programs in deep ocean mining, the US is consolidating its early leadership by the continuation of NOAA's authority under the Deep Seabed Hard Mineral Resources Act and the Sea Grant Act, Interior's authority under the outer Continental Shelf Lands Act, and by the development of a new Marine Minerals Technology Center within the Department of Interior's mineral institutes program, managed by the U.S. Bureau of Mines. The Center has a Continental Shelf Division (CSD) located in Mississippi, and an Oceans Basin Division (OBD) located in Hawaii. Research and training in the divisions is directed toward the practical aspects of mineral recovery from the nearshore and deep ocean environments with a strong bias for the OBD toward industrial and international cooperative programs in the Pacific Basin and Rim. In terms of resource development, the marine minerals in the Pacific Basin may be favored in some cases, in competition with land sources, by political and environmental considerations.

Jan 1, 1990

By Barrett D

The paper discusses the justification for the Open Pit Mining Operation at Central Norseman Gold Corporation Limited's North Royal facility.Open pit mining history is outlined together with production statistics and associated costs. Underground mining practice is discussed together with an outline of the problems with mining in oxidised ground.

Jan 1, 1984

By H Catchpole, L FontbotT, J PTrez, M Ageneau, A Bendez·

In the world-class mining district of Morococha, epithermal polymetallic replacement bodies and veins overprint porphyry mineralisation and skarns related to subvolcanic intrusions of Miocene age, thus indicating ore formation in two different environments, separated in time or forming a continuum. The district covers an area of about 70 km2 in the north-western part of the Domo de Yauli complex in theWestern Cordillera of central Peru and is part of the Miocene polymetallic belt, also hosting the deposits of Colquijirca (Bendez· et al, 2008b) and Cerro de Pasco (Baumgartner, FontbotT and Vennemann, 2008). Multiple late-Miocene porphyry stocks intruded Permian, Triassic-Jurassic and late-Cretaceous sedimentary carbonate and volcano-sedimentary formations, as well as large mid-Miocene barren intrusions. Extensive field work and detailedmapping of different styles of orebodies suggest that ore formation in the area was related to the late-Miocene magmatism. Good outcrop conditions and superimposing of different mineralisation styles make Morococha an ideal location for studying ore-forming processes in a complex porphyry-related magmatic-hydrothermal system in which porphyry-to-epithermal transition occurred. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

A modular computer-based monitoring system for mines is dis-cussed. The system consists of the following modules : production moni-toring system HADES, methane monitoring system CMC, seismoacoustic and seismometric systems SAK and SYLOK, communication systems. The system enables one to compose flexible,` economic structures according to the specification of a mine. Application of microcomputer-based monitoring and control systems in coal preparation plants also is discussed.

Jan 1, 1985

By F R. M Pires, Y Hasui, A Schrank

The iron ores of Alegria mine are composed of itabirites enclosing minor bodies of high-grade ores. The itabirites are classified according to mineralogical composition in five types: martite-rich, goethite-rich, specularite-rich, magnetite-rich and anphibolite-rich ores. The hematites are martite-rich, magnetite-rich, specularite-rich and more rarely, amphibolite-rich. Other classification criteria of the ores are based on the physical properties and the degree of compaction. As such, the itabirites and hematites can be classified as hard, friable and soft types. The mineralogical/textural evolution of the ores is linked to the pressure and temperature conditions that accompanied the tectonic processes in anphibolite facies and the different degrees of subsequent surficial weathering processes. Petrographic and microstructural studies indicate that the magnetite and amphibole bearing itabirites represent the parent rocks that created the other itabirites and that the specularite itabirites and the hard martite types are related to silica dissolution and redeposition in zones of high and low strain. Most of itabirites ores correspond to chert oxide facies banded iron formation, except the goethite and amphibole bearing itabirite that resemble a silicate or oxide-silicate facies with minor carbonate impurities. The great mass and pods of soft martite itabirites are probably shaley oxide facies BIFs with little volcanic contribution. Trace element contents of the AlegriaÆs itabirites show strong dissimilarities with BIFs associated with volcanism (Algoma type), but closely ressemble to the Lake Superior type, with high content in Cr, Co and low V, Ni, Cu and Zn. Although the absolute contents of REE present in the AlegriaÆs itabirites are, in general very low, the pattern when normalised by NASC is similar to the great majority of the Archean and Paleoproterozoic BIFs elsewhere in the world, and characterised by positive Eu anomaly.

Jan 1, 2002

A method is proposed for the determination of antimony in ores. Antimony is volatilized as antimony iodide by heating with ammonium iodide at a controlled temperature.The fusion mixture is extracted with hydrochloric acid and the antimony content is measured by atomic absorption spectrophotometry using an air/ acetylene flame. The time taken for analysis when comparedwith existing fusion and separation procedures is considerably reduced. Cations and anions likely to be present in antimony ores were also studied for possible interference effects but were not found to interfere.

Jan 1, 1972

The maintenance system for underground mobile equipment at Cobar Mines Pty. Ltd. has been modified from that originally planned as a result of experience gained in operating the equipment.Downtime due to breakdowns has been reduced by improvement of vehicle servicing and overhaul procedures.Frequency of breakdowns can be reduced by training operating and maintenance personnel to a high standard, ensuring adequate numbers of tradesmen and supervisors, good maintenance facilities and communications, a well designed mine layout, and a comprehensive stock of spare parts.A maintenance and downtime summary is compiled for each four-week operating period and this is useful in highlighting particular problems where corrective action must be taken.

Jan 1, 1969

The process selection and design aspects to treat primary ore in a new carbon-in-pulp (C.I.P.) plant while utilizing, where possible, existing equipment and infra- structure are discussed. The existing crushing plant, water supply, reagents, laboratory and infrastructure facilities from the heap leach have been upgraded and expanded to meet the C.I.P. plant requirements. The new power supply is from the North Queensland grid system. A series of metallurgical tests was carried out and a review of the data showed that the primary ore was amenable to conventional cyanide leaching. Following feasibility studies, a new process plant which included grinding mills, leaching, and adsorption tanks, thickener, desorption and gold roam facilities was constructed.

Jan 1, 1989