Search Documents

By J Santana, V Ferraz, G Pinto, G Cruzado

Morro Agudo is an underground zinc and lead mine owned by Nexa Resources. The mine uses room and pillar as the main mining method. The recovery of pillars as well as the opening of new excavations using sublevel stoping as mining method has been studied. On some occasions, the need to recover pillars and open a stope by using the sublevel method happens in a region that is already excavated or in deeper areas than those mined so far. These changes represent a major geotechnical challenge due to the complex openings of the mine and interaction between two different mining methods. Historically, geotechnical mapping, kinematic analysis and a 2D numerical model were used to evaluate the new mine openings, and in 2021, 3D numerical model was introduced, which enabled global and local assessment of new excavations impact and the stability of openings after recoveries. The 3D model, made with MAP3D, is used to evaluate each pillar to be recovered, considering the spans of the resulting openings, the ideal sequencing of removal to maintain stability, in addition to the impact and geometry of the pillars left in the chambers. Pillar recoveries done in 2021 and the impact of it on the pillars left were the sources of the back analysis to calibrate parameters inputted on numerical model to assess recovery on new chambers and Phyllite has been considered into the model and it has been a source of instability due to its parallel position to roof of room and pillars and stope hanging walls.

Nov 29, 2022

By L Nagy, K P. Juhasz

The authors were engaged to optimise a traditional rebar cage reinforced concrete segmental lining by means of finite element analysis (FEA) using macro synthetic fibres for the Shanghai metro extension. The aim of this study was to reduce or entirely replace the original steel reinforcement of the segmental lining, in order to make the precast production process faster and more economic. The outer diameter of the tunnel was 6200 mm, the thickness of the segments was 350 mm.The numerical calculations were performed by Atena Finite Element software, which is based on the combination of Menétrey-William and Rankine failure surfaces on the compression and tension sides respectively. The effect of the macro synthetic fibres was modelled as tension stiffening on the tension surface.A one-to-one full scale model of an assembled tunnel ring using the original reinforcement cages was tested at Tongji University in Shanghai, July 2013. The ring was tested to differing load levels where load and displacement were measured until failure. The author’s first step was to calculate the real displacement characteristics of the original reinforced concrete (RC) ring, then calculate the numerically modelled version, so as to compare them. The material parameters of the concrete and rebar used had been determined through basic material tests conducted at the Tongji University. (Bi, Liu and Wang, in press).The numerical modelling undertaken has shown good correlation with the full-scale physical test results. Optimisation of the lining reinforcement was achieved through the addition of fibres, resulting in a substantial reduction of the steel rebar cages. Several results have been computed with the numerical model using different dosages of macro synthetic fibres, showing that the mass of steel reinforcement could be reduced by 50 and 75 per cent respectively.CITATION:Juhasz, K P, Nagy, L and Winterberg, R, 2014. Full-round numerical modelling of a macro synthetic fibre reinforced tunnel boring machine tunnel in the Shanghai Metro extension, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By E Hondros

Innovation and Business Skills Australia (IBSA) commissioned The Boston Consulting Group (BCG) to undertake a study into how the role of AustraliaÆs senior managers is likely to change between now and 2020 and to identify the skills and attributes that will be needed to respond to those changes. This report builds on a previous study prepared by BCG in the early 1990s for the Industry Taskforce on Leadership and Management Skills (Karpin Committee), which provided a snapshot of the Senior Manager in 2010. The following powerpoint slides summarise the 2020 Vision û The Manager of the 21st Century û outlining how the role of AustraliaÆs senior managers is likely to change between now and 2020 and to identify the skills and attributes that will be needed to respond to those changes. The presentation is summed up in the following quote from Jon Nicholson û Senior Vice President of BCG: We believe that to succeed in the years up to 2020, executives will need to master a range of hard and soft skills. Amongst other things, they will require to manage multi-generaional teams, the creativity to measure staff performance on outputs rather than inputs, and a high degree of technical and functional expertise in addition to their general management credentials. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By B P. Voutharoj, R A. Dutch, M Paknezhad, T Ostersen

With the proliferation of new sensor technologies, acquiring multiple data sets over the same ground is becoming cheaper and easier than ever. This new, higher resolution multivariate data provides a significant resource for exploration and resource geologists but comes with the added complexity of effectively integrating the various data sets in useful and meaningful ways to elucidate new geological understanding. Both geophysical data sets and hyperspectral data are extensively used for exploration targeting, providing different information at different resolutions and crustal scales. One of the biggest challenges comes from trying to effectively integrate data sets that record very different physical properties, across the different scales these data are captured at, in a way which can allow for a data-driven analysis of these combined data sets.

Sep 1, 2024

By I M. Platten, Y Xie, B W. Cuffley, S C. Dominy

"Geometallurgical programs require the collection of representative samples for geochemical, mineralogical and metallurgical test work. Such protocols must be designed to suit the style of orebody in question. The distribution, proportion and size of gold particles have a direct impact on the effectiveness of sampling and test work protocols, and the gold recovery processes employed. Characterisation studies focusing on ore mineralogy, and gold particle deportment, size and distribution are required. High resolution X-ray computed tomography provides a non-destructive method for analysing the 3D nature of gold in rock samples. It can be used to calculate the modal abundance, particle size and distribution of gold in the sample volume. This paper presents a case study of the imaging of in situ gold particles in a high-grade gold ore. The Nick O’Time reef system comprises laminated quartz veins, which locally bear extreme grades of up to 100 oz/t gold. The mineralisation has previously been characterised from both a mineralogical and metallurgical perspective. Eight visible gold-bearing vein samples were scanned using X-ray microtomography. Microtomographic data were integrated with previous mineralogical and metallurgical test work outputs.CITATION:Dominy, S C, Platten, I M, Xie, Y, Cuffley, B W and O’Connor, L, 2016. Characterisation of Gold Ore from the Nick O’Time Shoot (Tarnagulla, Australia) Using High Resolution X-ray Computed Tomography, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J Lyons, S Baker, D MacHunter, D Pepper

Mineral processing plants require a storage buffer to bridge differences in production rates between mining and processing. Where coarse ores are processed, such as coal or hard rock, this buffer may be an ore stockpile or silo. For wet-mining processes, eg dredging or hydraulic mining, or where fine ores are slurried close to the mining face, a surge-bin is used to contain the plant feed and smooth out the variations in mining rates. These bins have gradually evolved from simple storage vessels to units that are now frequently part of the mineral separation process itself, such as providing a desliming function to remove deleterious ultrafine gangue. This feed conditioning is often essential to achieve the levels of plant performance required in times of declining ore grades and or where inherent ore characteristics make separations harder to achieve. To achieve these dual roles requires careful consideration of bin design factors such as geometry and lining selection and increased use of instrumentation and advanced, or remotely supervised, control systems. All this ensures they provide capacity to smooth out variations in mining rates and guarantees that when conditioning ores or adjusting slurry densities ahead of the plant it is achieved without loss of valuable minerals. This paper examines the evolution of the modern surge-bin from a simple, so called, constant density tank with its inherent mass-flow compromises, limited feed preparation and beneficiation abilities, and footprint penalty, to a current state-of-the-art surge-bin, the LFCU, with a control system which provides demonstrable steady outputs, while conditioning and in some cases beneficiating the ROM material and all from a highly compact unit. It further discusses their use in other applications around the world, for example providing the necessary security for long distant high-density pumping systems; constant high density, low water usage, tailings disposal pipelines and high capacity ultrafine iron ore beneficiation.

Aug 24, 2022

By J Player, G Sweby

The material properties and hence performance of saturated alluvial sediments slope can be incorrectly forecast if the water content is not preserved, and materials properties not correctly determined. The occurrence of saturated sediments in the Western Australia (WA) Goldfields, while not common, should be a significant investigation focus. Geotechnical engineers new to the area may be unaware of this and hence the importance of correct testing and determination of the material strength. Application of appropriate analysis to determine stable pit slopes to an acceptable level of risk, is not possible unless the appropriate strength and hydrogeological parameters have been established at the outset. A back analysis is presented of a pit that had extensive slope failures in alluvial clay-rich sediments with discussion on the approach adopted by the original design engineers to assess pit wall stability and consequent poor slope performance. Learnings from a full pit 3D back analysis are presented, with an approach to geotechnical and hydrogeological investigations and analysis for slopes in similar materials.

Jun 22, 2022

By G Pitkin, D Sorley

The purpose of any consultancy is to provide a superior service for their client. Organisational structure is a key element in providing this service and differentiating between consultants.In an organic organisation the emphasis is on effectiveness, problem solving, responsiveness, flexibility, adaptability, creativity and innovation. Such an organisation is able to respond in a timely manner to change because employees are empowered to be creative, to experiment and to suggest new ideas. The process of innovation is triggered by employees throughout the organisation in a collaborative manner.Problem solving becomes a core competence of the consultancy. A multidisciplined approach arrives at superior solutions that are rigorous, holistic, achievable and often novel. It allows the mining consultancy to extract the most from a very talented and experienced team.This paper highlights the advantages of an organic structure for a mining consultancy and how to implement such a structure. It draws on examples of innovative problem solving from feasibility and strategic studies carried out in Australia and Africa.CITATION:Pitkin, G and Sorley, D, 2016. Organic management structure – its advantages in a mining consultancy, in Proceedings International Mine Management Conference, pp 155-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By C Fricke, R Wood, P Velletri

"In a climate characterised by an ever increasing focus on cost reduction and maximising the utilisation of existing assets and infrastructure, understanding the uncertainty associated with alternative investment and operational choices becomes paramount to minimising the risk of making an ineffective decision. To assist in this process, TSG Consulting has developed an analytic framework to capture the underlying complexity of a mineral supply chain, and then quantify the impact of the uncertainty associated with the key drivers of business productivity. The technical basis of this approach follows three distinct steps: analyse the current system and identify the major factors that drive value build detailed models that can measure the response of the system to potential changes in the factors identified quantify the sensitivity of financial and capacity forecasts to these factors.Each of the above steps draws on a different area from the field of applied analytics, namely: data analytics dynamic modelling and designed experimentation meta-modelling and optimisation.Following the three-step approach described above ensures a rigorous modelling and analysis process is executed to support strategic mine planning decisions. The approach is equally applicable to the analysis of fully integrated system supply chains (pit-to-port), the evaluation of incremental capital investments to targeted areas of a supply chain, or when considering revisions to the operating philosophy of a system in the short term. The basis of each of the three analytic steps is explored in detail in this paper. The result is the definition of a structured mechanism for a business to actively manage risk and drive productivity as a component of the strategic mine planning process.CITATION:Fricke, C, Velletri, P and Wood, R, 2014. Enhancing risk management in strategic mine planning through uncertainty analysis, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By M Hawkes, Z Ji Gang, Z Ming, R Hassell

As underground mines become more geotechnically challenging with increasing depth and excavation size, the requirement for ground support to be installed as per design becomes more critical. The verification of installation quality for cable bolts and grouted rock bolts is difficult to assess. Current methods to control quality have limitations; pull testing is largely inconclusive with only extremely poor installation being identifiable. Audits during installation can only capture a small percentage of installed bolts. Following large rock mass displacement from either squeezing ground or seismic events, even previously well installed bolts may have yielded and require replacement. A method to provide an improved understanding of the reinforcement installation quality is Non- Destructive Testing (NDT) using acoustic reflection. To validate the accuracy of an NDT system, both plain and bulbed strand cable bolts were grouted in clear plastic tubes. The encapsulation grout quality was deliberately varied from full encapsulation through to partial encapsulation and a range of different size voids. The clear tubes allowed the ground encapsulation to be observed. Cable bolts strands were cut at varying lengths and different water cement grout ratios were used. Acoustic testing of the cable bolt specimens was completed blind; the technicians were not aware of what was being tested. The NDT results correlated well with the grout encapsulation, with differences between full encapsulation, minor voids and major voids being determined. The different water cement ratio and bolt lengths (including when partially cut) were also identifiable but with some discrepancies. Trials of the technology underground have also shown the data collection process to be relatively quick with each bolt taking 1-2 minutes to test, with interpretation of the results able to be completed soon after. The NDT results collected from the underground trial showed a wide variance in cable bolt grout encapsulation quality indicating that there were installation issues.

Mar 15, 2021

By A Finch, C Pridmore

The Cosmo Project falls within the Archaean to Palaeo-Proterozoic Pine Creek Orogen, one of the major mineral provinces of Australia.The Cosmo Deposit is interpreted to be a series of steep north-west-plunging gold mineralised vein, breccia and shear systems within the tight Howley Anticline and hosted within interbedded siltstones, mudstones, banded iron, phyllites, dolerite sills and greywacke.A folded environment poses a number of technical challenges, particularly for estimation.Handling of tightly folded and in some cases narrow domains might include subdomaining for orientation, omni-directional three-dimensional (3D) estimation within constrained domains or software-enabled unfolding/un-wrinkling procedures (transformation of the data and estimate space into a two-dimensional environment). Each technique has its own unique set of advantages and disadvantages.A further method (one applied at Cosmo) is where the estimation parameters (specifically search and variography orientation) are modified in a frequent or ‘dynamic’ sense to suit the orientation of the domain whilst maintaining 3D space. Control of the resource estimation orientation can be done in several ways, including the use of sectional panels of a specific size or, alternatively, orientation sector divisions. The sector approach provides some significant reductions in processing time over the panel technique and could be applied in a number of software packages.Three-dimensional ‘dynamic’ interpolation reconciles well with production data from Cosmo, whilst the sector method provides a practical technique that can be executed without the complications of transformation or the need for labour-intensive orientation subdomaining and with acceptable resource estimation run time.CITATION:Finch, A and Pridmore, C, 2014. Dynamic interpolation – estimation in a folded environment at the Cosmo Deposit, Northern Territory, Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 107–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J N. Farrell

Metallurgists frequently use a small number of large samples to characterise expected mill performance, with the a priori assumption that these few samples are representative of the entire deposit. Geometallurgical sampling is becoming more prevalent as a way to use many smaller samples to indicate the expected recovery as part of the Mineral Resource or Ore Reserve estimation.Recent increases in prices for iron ore, together with the potential to produce high iron and low contaminant concentrates, have resulted in a renewed interest in recovering magnetite from banded iron formation and other deposits.Geometallurgical evaluation of magnetite involves approaches to sample preparation, sample analysis and resource estimation that are different from the methods commonly used for haematite iron ore. The magnetite sampling protocol is specific to each deposit, and is typically designed around a specific metallurgical flow sheet.The sampling protocol will typically include the use of Davis Tube analysis. The Davis Tube is a bench-scale test that is used for determining the mass magnetic recovery from a small amount of sample ground to a specific size. The magnetic concentrate may then be analysed and together with the mass magnetic recovery, may be used to simulate the expected mill recovery.During resource modelling, the mass magnetic recoveries and concentrate grades may be assigned to a block model using regressions with other chemical constituents, or may be estimated directly. For estimation of the concentrate grades, a weighting can be applied to account for the different mass magnetic recoveries from each sample and the impact of these differences on the concentrate estimates.This paper presents an overview of the use of metallurgical test data in resource evaluation for magnetite deposits.

Jul 11, 2011

By D Corley, J Moore, M Grant, A, W R

Resource estimates are the corner stone of technical and investment decision-making. Prior to mining, resource estimation uncertainty has the greatest potential to lead to poor investment decisions, despite a significant component of resource estimation uncertainty being unknowable at this critical stage in the mining cycle. This presents a conundrum to the resource geologist in terms of risk evaluation and resource classification. Ahead of mining, there is normally considerable focus on drill hole spacing analysis to determine the ‘optimal’ drill hole spacing, taking grade and geological continuity into account; cost-benefit analyses balance improved resource definition against cost; the law of diminishing returns and the exponential cost increases acting together as spacing is reduced. Typically, a lower limit to the drill hole spacing is identified. After completing the resource drilling to an agreed spacing, resource estimation is then undertaken. At this point it is common to attempt to bracket the resource estimation uncertainty. In many cases conditional simulation is used, based on a modelled, but largely assumed, variogram model. It is also assumed that the histogram of the available drill hole sample data is representative of the in-ground mineralisation. The purpose of this paper is not to diminish the importance of drill hole spacing and simulation studies, but rather to illuminate an important aspect of estimation uncertainty that, although previously recognised, is typically overlooked – the question of how representative the available data set is in characterising the true (but unknown) distribution of mineralisation. To do this, we lift the lid on one of OceanaGold’s former operations, the mined-out Globe Progress Mine, by resurrecting a high quality, close-spaced, reverse circulation (RC) grade control data set. The Globe Progress Mine is within the West Coast Region of New Zealand, it was closed and transitioned to rehabilitation in 2016 and is now known as the Reefton Restoration Project. The exhaustive Globe Progress grade control data was used to repeatedly ‘redrill’ the deposit by extracting 35 m × 35 m spaced subsets from the original 5 m × 5 m spaced grade control data. Utilising closely spaced grade control data removed the need for assumptions regarding short range continuity, which are necessary with forward-looking analyses that are based upon broader spaced resource drilling. The extraction process used a nearest neighbourhood algorithm, repeatedly moving the origin in 5 mE, or 5 mN increments. Individual resource estimates were then completed for each of the extracted drill hole data sets (49 in total) as well as a grade control estimate based upon the exhaustive data set. Whilst the data unpinning each of the 49 estimates changed, the geological assumptions, variography, and modelling parameters remained constant. This approach was taken to isolate the impact of changing the input data. The 49 estimates were then compared against each other and the grade control estimate. The mean of all 49 sensitivity estimates was close to that of the grade control estimate in terms of contained gold, tonnes and grade. Whilst it is acknowledged that the grade control estimate itself is subject to some degree of estimation uncertainty, the close match between the average of the 49 estimates and the grade control estimate suggests that the resource estimation methodology is reasonable and appropriate. Whilst this comparison is important, the focus of this study is on the component of estimation uncertainty related to the underlying data, and this is reflected in the spread across the estimates. The spread across the 49 global estimates (highest to lowest) for this particular Mineral Resource Estimation Conference 2023 | Perth, Australia | 24–25 May 2023 142 case study was found to be significant (approximately 20 per cent in grade and metal) and that is attributable solely to the underlying data. This exercise quantifies a component of the estimation uncertainty that is inherent to all drill hole data and is distinct from the uncertainties associated with modelling methodology choices, sample and subsample quality and drill hole spacing-related interpolation uncertainty. Importantly, this uncertainty is unknowable prior to mining; we can only directly compare the resource drill hole data against grade control data after mining has taken place. For the case study, approximately 65 per cent of the estimates fell within 5 per cent of the grade control estimate for contained-gold, suggesting that for many projects the histogram of drill hole data is unlikely to differ noticeably from that of the in-ground resource. However, about 15 per cent of the estimates in this study differed by more than 7.5 per cent, suggesting that a not-insignificant proportion of estimates will be materially compromised. Whether or not the available drill hole data is representative comes down to the ‘luck of the draw’ and cannot be known at the time of resource estimation. Given the challenge of attempting to evaluate forward-looking estimation uncertainty, a component of which that can only be quantified retrospectively, what should we do as resource geologists? What are the implications for risk evaluation, resource classification and reconciliation? Furthermore, without rigorous post-mining data checks, resource geologists may conflate suboptimal modelling with the shortcomings of the underlying data. An example of this problem is discussed in the following section.

May 24, 2023

By A Murphy, I Samsonova, N Eastwood, D Whittle

Part XI of the United Nations Convention on the Law of the Sea (UNCLOS or the Convention) (United Nations (UN) Division for Ocean Affairs and the Law of the Sea, 1982) establishes a comprehensive regulatory framework for the conduct of deep seabed mining (DSM) activities of mineral resources in the Area (defined in Article 1(1) of UNCLOS as ‘the seabed and ocean floor and subsoil thereof, beyond the limits of national jurisdiction’). Under that framework, DSM activities can only take place in the Area pursuant to an approved Plan of Work in the form of a contract with the International Seabed Authority (ISA) (the Authority), a 168-member international body created under UNCLOS to administer the Area. Private contractors can undertake DSM activities if they are sponsored by Member States of UNCLOS, providing a dual system of international and domestic regulatory control and oversight for activities in the Area.

Sep 1, 2024

By L Hussey

Mt Keith concentrator treats low grade disseminated nickel sulfide ore supplied from the adjoining open pit mine. It is a traditional crushing, two-staged closed circuit grinding circuit (SAG & Ball Mills), followed by a complex split-size rougher, scavenger and cleaner flotation circuit. In 2016, 10.5 Mt was milled, at an average head grade of 0.54% Ni, yielding 35 000 nickel metal tonnes in concentrate.Historical analysis of the plant data indicated that of all the nickel lost in the fines rougher circuit tails stream, 25.6% was recoverable in an eight minute laboratory scale flotation test. These results implied that this fine nickel was readily available for recovery in the plant, either through operational improvements or additional flotation capacity. With operation optimisation ongoing, and capital within the business focused elsewhere, plant personnel were challenged to think differently about improving recovery.In 2012, a separate project to improve plant recovery when treating high talc ore was completed. Amongst other vessels, this project saw the installation of two 150 m3 Outotec Cells to the scavenger section of the fines rougher, middlings and scavengers (RMS 1) circuit. Since installation, the operation of these cells resulted in difficulties immediately upstream with instability in the scavenger cells. It was therefore decided that these cells would be better suited to treating the fines rougher circuit tails.The alterations required to divert these flows were minimal, with the capital project totalling $220 000.In the two years since installation, the fines rougher tailings nickel grade has dropped by 9.9%. The scavenger circuit has also seen a 2.8% reduction in tailings nickel grade, and instability issues were immediately resolved. This project serves as a lesson in how existing plant infrastructure may be better utilised to maximise recovery. Although this is especially applicable when capital constrained, such re-appropriation can be considered at any point to maximise return on existing assets. CITATION:Hussey, L, 2017. Repurposing flotation capacity at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 254–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Reilly SY, Green TH, O&apos

Alkali feldspar meggacrysts are commonly found (with aluminous clinopyroxene, kaersutitic amphibole, titanomagnetite, ilmenite and apatite, and more rarely with zircon and corundum) in alkalic basalts and their derivatives as discrete crystals and fragments. They are commonly euhedral or subhedral and may be up to 15 cm in size. Their occurrence has been reported from many localities around the world, e.g., Africa, Antarctica, eastern Australia, eastern China, East Fife (Scotland), Eifel (Germany), Massif Central (France), Mongolia, New Zealand, New Mexico (USA) and Siberia (USSR). These megacrysts are relatively homogeneous and belong to the Na-rich anorthoclase group, although Kutolin and Frolova (1970) called them sanidine due to their monoclinic nature. The majority of megacrysts have a molar orthoclase content (Or%) between 20 and 30 (Fig.1). These anorthoclase megacrysts possess a high degree of disorder, with the structural state belonging to the high albite-high sanidine series (Hoffer and Hoffer, 1973; Chapman, 1976).Published interpretations of the origin of anorthoclase megacrysts fall into the following two categories: either (1) Anorthoclase together with the associated pyroxene and amphibole crystallized from basaltic magmas as phenocrysts (cumulate phases) at high pressure and the present host basaltic rocks are the parent magmas for the anorthoclase megacrysts (Binns,l969; Binns et al. 1970; Kutolin and Frolova, 1970; Hoffer and Hoffer, 1973; Laughlin et al. 1974); or (2) Anorthoclase probably crystallized from a more evolved liquid at relatively lower pressure and was then picked up and carried to the surface by a later

Jan 1, 1990

In a previous paper in these Proceedings(l) it was shown from a study of the bore'logs and analyses then available, that the brown coal seams of the Latrobe Valley areas show progressive changes in composition with increase of stratigraphic depth, equivalent to a rise in rank: These changes appear as:(i) An increase in ultimate carbon and hydrogen, calculated on a dry, ash-free basis, and(ii) An increase in calorific value, calculated on the, same basis, each of the order of 1% per 100 ft. of depth, and(iii) A decrease in moisture content of the order of 0.5% to 1.0% per 100 ft. of depth. The decrease in moisture content was found to be less regular than the other changes. In some bores the moisture content remained more or less constant throughout a single seam, or fluctuated slightly, decreasing stepwise on passage to the seam below.It was noted that individual analyses within a bore showed irregular fluctuations, tending to mask the general trend in composition change. This was particularly so for the moisture content, which had been determined for 10 ft. lengths of core, whereas the other components were determined for 50 ft. lengths of core. Averaging of the moisture contents over 50 ft. lengths reduced the masking effects of these irregularities. The suggestion was made that these irregularities arose from variations in the relative proportions of pollen, resin, wood (lignite) and woody attritus composing the core. Such variation in the coal seams has since been established in some detail for the...

Jan 1, 1948

During October 1947 an Authority to Prospect was granted by the Minister of Mines to lVIount Isa Mines Limited over an area of approximately 75 sq. miles to the north of Mount Isa.Application for the Authority to Prospect had been made after Zinc Corporation Limited had been granted prospecting rights over two areas, one of 1,265 acres immediately to the north of the Mount Isa Mines leases and the other of 1,960 acres adjoining the south end of Mount Isa Mines leases.METHODSAs a means of providing a cheap map of sufficient accuracy on which to plot geological features, both Mount Isa Mines Limited and Zinc Corporation Limited agreed upon aerial photographs and the two companies shared the cost of an aerial photographic survey by Adastra Airways of 130 sq. miles which covered the prospecting areas held by both companies.The photographs were on a scale of 800 ft. to I in. with 60% overlap on the north-south runs and 25% overlap east-west. A set of alternate prints enlarged to 400 ft. to 1 \in. were obtained for field work. The 400 ft. to 1 in. scale unglossed photographs (size 18 in. x 18 in.) were taken On to the field and rock outcrops, and uncorrelated structures were plotted directly on to them in red crayon pencil. The geological observations were then transferred in the office to a tracing on which accuracy of azimuth and scale was controlled by use of a photo mosaic and ground surveys.

Jan 1, 1953

By S Doyle

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Macraes gold mine in Otago, New Zealand, is developed along the central portion of the Hyde-Macraes Shear Zone (HMSZ), which dips gently to the NE, and is traceable over 30 km of strike, before disappearing under tertiary cover. Mineralisation is most intensely developed along the hanging wall shear, which defines the upper limit of the shear zone, although significant packages of quartz vein arrays and mineralised shears occur sporadically beneath the hanging wall shear.The Macraes gold mine is now in its 25th year of operation, well beyond the projected mine life at the time of commissioning in 1990, and currently contains over triple the measured and indicated resource inventory that was defined at start up. The extended mine life and resource growth has been driven by exploration and resource development success, efficient low-cost mining and processing, improving gold price, as well as an ethos of continuous improvement.The emphasis of Oceanagold’s exploration and resource development has shifted over time; from hanging-wall-focused mapping, soil sampling and step-out drilling, through exploitation of previously drilled stockwork mineralisation, to the pursuit of blind, higher-grade underground targets.Mineralisation within the HMSZ remains open at depth, and the regional potential has not been fully tested. Given the relatively low-grade of gold mineralisation at Macraes, the consideration of tungsten as a supplementary co-product provides an exciting opportunity.CITATION:Moore, J and Doyle, S, 2015. Resource definition in the world-class Macraes gold mine, New Zealand, in Proceedings PACRIM 2015 Congress, pp 557–564 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M Campbell, A Jeffcoate, J-C Vannay, B Perriaux

Phyllite waste rock at the Simandou Pic de Fon and Oueleba Iron Ore deposits (Guinea, West Africa) variably weather to form clay-rich rocks. This weathering modifies the mineralogical, geochemical and mechanical properties of the phyllites. Final pit walls will largely be formed in phyllite, so it is critical that the slope design takes account of the distribution and variability of weathering within this material. Phyllite intact material strength has been correlated with geochemistry (ie mineralogy) facilitating the establishment of domains of intact rock strength (IRS). In order to calibrate this geochemically-based strength model, core from diamond drilling (DD), comprising a variety of phyllite material types (from soft clay to moderate strength rock), was geotechnically logged to assess intact strength; further validation was achieved by uniaxial compression (UCS) testing and point load tests (PLT). The correlation between geochemistry and strength offers a potentially powerful tool for differentiating basic mechanical properties of the rock mass, especially at Simandou where a significant proportion of the resource drilling is done by reverse circulation (RC). Unlike DD, reliable measurements of material strength from RC samples can prove difficult, especially in clay-rich material. Therefore, gaining information from routine geochemical assay results, independent of the sampleÆs physical integrity, is a valuable and cost-effective source of reliable empirical data. Data acquired using this approach provides an opportunity to develop strength domains, which are integrated into mine planning block models. In combination with other geotechnical characteristics, this can be a valuable input to the development of geotechnical models. This technique has allowed spatially representative rock strength data to be derived and offers the potential for optimising pit slope angles in areas where hitherto conservative design criteria had been assumed.CITATION:Jeffcoate, A, Campbell, M, Vannay, J-C and Perriaux, B, 2013. Modelling intact rock strength of clay-rich rocks with geochemistry at the Simandou iron ore deposit, Guinea, West Africa, in Proceedings Iron Ore 2013 , pp 193-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013