Search Documents

By Ishijima Y, Goto T

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic ar- ray. Location of microseismic events and in- tensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the inten- sity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increas- ing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are con- sidered. Observed and predicted displacement of the shaft axis agreed well.

Jan 1, 1992

This paper traces briefly the reasoning which led to the decision to extend the existing internal shaft at the Rosebery Mine and to instal underground a larger winder (No. 2 Hoist) with capacity to handle all hoisting requirements to a depth of approximately 2,500 ft. on an incline varying from 83" to 55" to the horizontal. It then covers the specifications and selection of the winder, the design of the winch chamber, rope raise and bins, the excavation, support and lining of the chambers and the transport to site and installation of the machinery. Finally a brief description is given of the mechanical and electrical parts of the winder.INTRODUCTIONThe existing shaft winder on the internal inclined shaft situated on No. 8 Level of the Rosebery Mine had reached the limit of its capacity. Hoisting 21-ton capacity skips in balance, with a 13/16-in. diameter rope, it required four layers of rope on the 3 ft. 6 in.drums to reach the loading station under No. 12 level at a depth of 864 ft. (Fig. 1). This entailed heavy wear on the multi-layered rope and heavy stresses on the cheeks of the drums. Continuous working on three shifts was necessary to handle ore, men and materials, and a hold-up from any cause whatever meant an interruption to production on the lower levels of the mine. The maximum output of the hoist whilst hoisting from the No. 12 level loading station was 50 tons per hour. It was obvious therefore, that a larger winder was required if output was to be maintained.Diamond drilling had proved the existence of sufficient ore at depths well below No. 12 to warrant exploitation and a decision had to be reached on the means of hoisting this ore.

Jan 1, 1958

It is recognised by the current JORC (1999) code that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological continuity and grade continuity. No prescribed criteria and rules will work for all situations or even between different ore types within the same deposit. Also these criteria and rules are sometimes applied without a clear understanding of their appropriateness, accuracy or correct implementation. For these reasons case studies are useful to evaluate and compare criteria commonly used to assist in resource classification. In this paper blasthole data from a selected area of Joffre Member hosted ore of the Brockman Iron Formation at the Mt Whaleback orebody are used as the basis of a case study for the above-mentioned purposes. Iron grade, in per cent, is interpolated from a blasthole dataset into a block model using ordinary kriging. Samples are then removed from this blasthole dataset to produce a random sample grid, a semi-random sample grid and a regular sample grid. Using nearest neighbour, inverse distance squared, ordinary kriging and sequential gaussian simulation, block iron grades are estimated using these three blasthole data subsets as inputs. This provides four groups of estimates with the ordinary kriging estimate based on the complete blasthole dataset being considered to represent the true estimate of iron grades. Also generated during this process are estimates of the error for each block. These error estimates range from the simple, such as drill spacing, through to more advanced methodologies such as kriging efficiency and simulation. These estimates of grade and grade estimation error are then compared to the true estimate using graphs and statistics. In order of increasing accuracy the block grade estimation and simulation methods were nearest neighbour, inverse distance weighting, ordinary kriging and finally conditional simulation. The simulation in some instances doubled the accuracy of individual block grade estimates when compared to nearest neighbour and inverse distance weighting estimates. It was found that many methodologies for estimating the error of individual blocks performed equally well with only methods such as average drill hole spacing and classification by search ellipse pass number performing poorly. An approach on how to convert the abovementioned error estimates of individual blocks into a meaningful JORC classification is also discussed. Although advanced non-linear resource estimates are applicable, most iron ore mines are still using relatively straightforward methods. The use of blasthole data and some simple linear interpolation methods and simple linear based error estimates makes this study repeatable for most iron ore sites and their resource geologists. This style of investigation is recommended as a useful approach for the Competent Person to apply to their deposit and thus better select, implement and understand the criteria used for resource classification and provide more consistency and confidence in the resource classification process.

Jan 1, 2002

By D Cliff

"It has been 17 years since the mine disaster at Moura No 2 Mine in Queensland. Recent disasters in the USA and New Zealand prompt the question what has changed since 1994. This paper att emptsto answer this question and identify areas that need improvement."

Jun 1, 2012

By G, F Beach, D Jazzini, R Rounsley

Over the past 20 years within Australia, there have been a number of incidents at mine sites where ammonium nitrate-based explosives have reacted with certain rock types containing sulfide minerals. These rocks have commonly been referred to as æreactive groundÆ. These reactions have frequently led to fires (particularly in ground susceptible to spontaneous combustion) or premature detonation of the ammonium nitrate-based explosives. Clearly, this introduces an element of risk when using ammonium nitrate-based explosives in these areas. Dyno Nobel has been proactive in developing ammonium nitrate-based explosive products that can be used in these types of æreactive groundÆ environments that minimise the risk of premature detonations occurring. A system for assessing æreactivityÆ of sulfide containing rocks has been developed that can be used in the field. Previous literature has been reviewed, identifying Differential Thermal Analysis (DTA) as the most common method for determining the æreactivityÆ of the ground. In the present investigation, DTA has been rejected as a suitable technique for determining ground reactivity, since it measures thermal reactions at higher temperatures over short time periods, conditions that are unlike those in the field. For example, ground at ambient temperature has been found to react with ammonium nitrate-based explosives over long time periods, reactions that are unable to be evaluated using DTA. Other more suitable techniques have been developed to monitor rock conditions that can be measured in the field and give a good indication of potential ground æreactivityÆ with ammonium nitrate-based explosives. Dyno Nobel is currently investigating the reaction mechanisms of spontaneous combustion in reactive ground, the decomposition mechanisms of ammonium nitrate and the role of inhibitors in ammonium nitrate-based explosives. Once complete, this fundamental research will lead to the further development of even lower risk ammonium nitrate-based explosive products for use in æreactive groundsÆ in a variety of mine environments.

Jan 1, 2003

By S Arnold

Properties of the soil profile fundamentally control water-limited ecosystems. Soil water availability affects vegetation dynamics of plant communities, but is also affected by these communities in return. Understanding this eco-hydrological interplay and the role of physical soil restoration is crucial for successful rehabilitation and management of post-mining landscapes in semi-arid areas. However, uncertainties exist in both the mathematical description of plant communities within ecological submodels and the predictability of future rainfall events. This study uses information gap decision theory combined with an ecohydrological system model to investigate how both uncertainties impact decision-making in the context of ecosystem rehabilitation. A range of management strategies are investigated to identify the optimal soil thickness for successful rehabilitation of native plant communities in Central Queensland. The results emphasise that thicker soils can counterbalance uncertainty in mathematical description of plant communities by increasing the simulated survival probability of plant communities. However, the influence of thicker soils on the robustness of plant communities against a change in future rainfall amount is rather marginal. By allocating an economic value for restoring a particular thickness of soil layer, these results can be used to evaluate the costs of ecosystem re-establishment with regard to two target measures - the survival probability of the plant community and their robustness against climate change.CITATION:Arnold, S, 2012. Finding optimal soil restoration strategies in the face of uncertain future rainfall amount, in Proceedings Life-of-Mine 2012 , pp 91-96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Wang Xia, Zhou Aiming, Shi Shengyi

Zhangmatun Iron Mine is situated in the suburbs of Jinan city, Shandong, China. Because of surface environmental constraints, no suitable site can be selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a doubleshaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two stopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining. Utilisation of cemented tailings backfill solves not only the problem of disposal of mill waste, but also the resource problem of providing backfill materials to the mine. The strategy also maximises ore recovery for the mine.

Jan 1, 1998

By X Yu, Y Shen

The iron ore products should be assessed in terms of in-furnace behaviour and overall furnace performance, their operation should also be optimised under industry-scale blast furnace (BF) conditions, in order to be sustainable and competitive, especially in the context of decarbonisation efforts in ironmaking. While lab and pilot-scale experiments can provide useful kinetics, they are expensive and risky and cannot replicate industry-scale blast furnace conditions for proper assessment and optimisation. In this paper, we review our recent progress at Shen Lab of UNSW in using state-of-the-art Computational Fluid Dynamics (CFD) models to assess iron ore products and examine the effects of their operations on BF behaviour in basic terms, including in-furnace phenomena (flow field, temperature field, species distribution fields etc) and overall BF performance (coke rate, reduction efficiency and top gas temperature etc). We have developed state-of-the-edge CFD models for different purposes, ranging from the static-state BF model featuring unique layered burden structures for offline assessment and optimisation knowledge building-up for iron ore products, to the transient-state BF model for online assessment and optimisation of iron ore productions by describing the transient behaviours of iron ore productions under industry-scale conditions. First, we have studied several iron ore products including the iron ore products used in the present BFs and emerging iron ore products like carbon composite briquette and iron-coke. Second, several iron ore operations are studied including optimisation of conventional burden operations like oxygen enrichment, batch weight tuning and new operations like coke central charging and hydrogen injection in BFs. Third, some time-sensitive operations are also investigated including the use of wet burden materials and the drop in blast temperature on BF performance. These CFD models offer cost-effective research tools for understanding the effect of iron ore products on BF performance and serve as a reliable marketing tool for existing and emerging iron ore products under a wide range of BF conditions.

Sep 18, 2023

Anglo Platinum recognised with its expanded operations the need to change its evaluation strategy due to increased sample volumes and the pressure it created at laboratories. The sender/receiver analytical scenarios had to change in order to curb costs and to prevent substantial investments in new sampling and analytical facilities. Given the high cost associated with correct sampling systems and sampling protocols and the shortage of technical resources a strategy of single point sampling and analysis was introduced. The analysis was then done at an ISO17025 accredited laboratory with ten per cent checks, subjected to careful statistical scrutiny. Logistical problems increased with respect to weighbridge congestion, maintaining sampling quality, throughput of samples in the sample preparation areas, manual quality control systems in place, audit trails and analytical capacity throughout all operations. This required the expedited improvement of existing sampling practices and the development of new sampling methods and equipment. Anglo Platinum is classifying and standardising sampling equipment, sample preparation and analytical procedures for all process streams with the view to minimise overall uncertainties. Major investments were made into a customised LIMS and automated equipment for data management, reduction of manual transcription errors and streamlining of sample processing. Anglo Platinum is committed in rolling out the enhancements to all sites as priority dictates.

Jan 1, 2008

Passive systems for the treatment of acid mine drainage (AMD) are typically more economic in the long term than active systems. Various flow charts for treatment selection have been prepared by scientists in the USA, however, they have typically not included a variable important at New Zealand AMD sites on the West Coast: topography and available land area. Very steep topography, dense and often protected vegetation (and animals such as snails), and a high-rainfall climate result in AMD with very high flow rates in locations with very limited space for remediation. Flow charts specific to New Zealand have been prepared which accommodate topography and available land area. Parameters necessary to use the flow charts are iron and aluminium concentrations, pH, ferrous to ferric iron ratio, dissolved oxygen concentration, topography and available land area. Prior to full scale construction, is it recommended that flow rates be quantified, small-scale trials be conducted, and cost, effectiveness, limitations, and risk of failure be reviewed for various options. One full-scale remediation system has been installed in New Zealand based on this methodology and another is planned. The performance of these systems, as well as future systems to be installed, will be used to validate these treatment system flow charts.

Jan 1, 2007

By B R. Olsson, N Marinopoulos

To establish the design and the capacity of the Stanwell Magnesium Plant, Australian Magnesium Corporation Ltd (AMC) with Fluor Australia has modelled the operation of the magnesium plant using ARENA Simulation Modelling. The reliability model has been used to evaluate: surge capacities required between different sections of the plant; critical equipment requiring standby capacity; the number of trains required for different sections of the plant; and potential capital cost reduction options. The reliability model was established using the detailed Process Flow Diagrams, reliability information from literature and maintenance, operation and start-up experience from the Demonstration Plant. The model was run with different plant configurations to assist AMC in determining the most effective configuration to provide the production capacity at the lowest capital cost. The model was not only able to confirm the plant capacity to the independent technical expert but was able to minimise quantitative risk by minimising the quantities of hazardous materials on site. Fluor Australia provided the ARENA simulation expertise and has used this software for optimising new plant design and to establish improvements in operating plants. Reliability modelling is a normal feature of chemical plant design but is rarely used in the resource industry. The experience gained by AMC in the modelling system has indicated that metallurgical plant design can be improved by the application of reliability modelling.

Jan 1, 2002

The history and milestones in the evolution of support systems utilised in the mass-mined chrysotile mines of Shabanie and King are discussed in detail. The use of block caving, false footwall or sublevel caving mining methods brings with it some major support problems, which are exacerbated, in our low rock strength mining environments. The paper discusses the various support elements and systems that have been used successfully or otherwise in these operations. Some predictions for the future of rock reinforcing in our ground conditions are highlighted, in relation to geomechanics, levels of mechanisation and production risk analysis.

Jan 1, 2000

By M Maulen, K van Olden, T Elkington

A large open pit is planned at the site of an existing underground mine. Strategic planning work has been undertaken to investigate the project value associated with an expansion of underground operations in conjunction with the proposed pit. Previous analysis determined that any depletion of the available pit resource that changes the optimum pushback sequence has a significant negative impact on overall project value. Therefore, to investigate the viability of an underground expansion requires a system to identify the stope resource that would add value to a combined operation if mined ahead of the pit. The key solution to this problem was to generate a resource model variable that defines the blocks, which have greater discounted value if mined by stoping rather than by the open pit. A key assumption was that the open pit is the main driver of overall project value. From the identified potential underground resource, series of mineable stope shells were generated at a range of cut-offs. This stope reserve data formed the input to a mixed integer program based software tool that was developed and used to optimise the underground mining plan, at conceptual level, for various project configurations. A dynamic programming tool was then applied to evaluate the optimum value of a combined open pit and underground operation. The overall objective of this project was to determine the strategic plan that yields the optimum value for a combined undergroundûopen pit operation. The results provided a clear focus and direction for more detailed design and planning.

Jan 1, 2009

By F Brenguier, R A. Lynch, G Olivier

The seismic velocities of intact rock are dependent on the applied stress. Unfortunately, the low susceptibility of seismic velocity to stress changes mean that changes in seismic velocity have to be measured extremely accurately to infer stress changes from them. Previously, it was thought that measurements of this accuracy could only be made with active sources or repeating earthquakes. In this paper, we show that the noise generated by mining activity can be used to construct virtual seismic signals with which we can measure changes in seismic velocity accurately enough to see the short- and long-term effects of a production blast on the surrounding medium. The time-dependent velocity variations achieved with this method show that the blast caused weakening of the rock mass for the rock within a radius of 200 m of the blast. The weakening is healed by confining stresses over a period of five days, after which permanent changes in the seismic velocity can be seen. The size and spatial distribution of the seismic velocity changes were compared to modelled changes in static volumetric stress, which supported the notion that seismic velocity changes can be used to measure the redistribution of stress after a blast. The results of this study indicate that this method can be a powerful tool to evaluate the evolution of stress in a mine at a relatively low cost as the data that it uses would normally be discarded.CITATION:Olivier, G, Lynch, R A and Brenguier, F, 2016. Measuring the redistribution of stresses resulting from new excavations with ambient seismic noise correlations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 873–878 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

By C Zhang, R Liang, I Canbulat, S Saydam, B Li

The integration of digital twins in mining represents a significant advancement towards enhancing operational efficiency and decision-making. Central to this development is the role of visualisation, a crucial element in mining digitalisation. This paper aims to develop a data-driven visualisation solution for the construction of mining digital twins, highlighting how this innovation revolutionises the representation of physical mining environments. It spotlights the shortcomings of conventional visualisation methods, particularly their inability to accurately depict complex underground environments and their predominantly historical orientation. To address these challenges, this paper proposes a novel, data-driven approach. This approach extensively utilises CAD files, encompassing data from geological surveys to intricate mine plans, thereby significantly elevating the precision of digital twins. It supports real-time updates and enables flexible interaction with a variety of data types. Moreover, it introduces a comprehensive data diagram alongside the adaptation of a 3D tile index. This strategy ensures the efficient rendering of extensive mining environments, allowing for a more dynamic and interactive digital twin model. In conclusion, the implementation of data-driven visualisation in the construction of mining digital twins marks a pivotal advancement in the industry’s digital transformation. It promises a more detailed, accurate, and dynamic depiction of mining operations.

Sep 1, 2024

By K A Plumb

New structural studies in the Walker Fault Zone of eastern Arnhem Land are integrated with basin-wide reconnaissance observations, made to refine models for the structural evolution of the McArthur Basin and provide new insights into the nature of metal logenetical ly important pre-inversion phases of the basin's evolution. At least five principal events may be identified during the Proterozoic: The Tawallah Group and equivalents were deposited throughout the McArthur Basin during an extensional event. Rifting of an incipient Batten Trough occurred at this time, in a terrain characterised by orthogonal, linked extensional faults. Uplift and erosion of the Tawallah Group accompanied continuing extension and was penecontemporaneous with continuing deposition of the overlying Parsons Range Group, within a precursor to the Walker Trough. Dt (of the Walker Fault Zone) relates to a new rifting event, penecontemporaneous with deposition of the McArthur Group and its equivalents in the Walker and Batten Troughs. This rifting accompanied dextral strike-slip faulting along northerly-trending bounding faults, as a result of northwesterly-directed oblique extension, leading to pull-apart basins. D2 inversion of the Batten and Walker Fault Zones pre-dates deposition of the Roper Group. In the proposed model WNW-ESE directed shortening (D2.), accompanied by folding and thrusting, and by local development of cleavage in the Walker Fault Zone, is seen to be followed by northerly-trending sinistral faulting (D2b), about a SE to ESE-directed compression. D3 is basin-wide and post-dates the Roper Group. It is characterised by conjugate faulting and folding about ENE to NE-directed compression. The latest Proterozoic event to be identified (D4) comprises widespread north-trending strike-slip dextral faulting of Roper Group, coupled with N-S directed thrusting across the Urapunga Fault Zone and Murphy Inlier This is accompanied by late dextral reactivation of NNW to NNE-trending faults in the Walker and Batten Fault Zones.

Jan 1, 1994

By D Giurco

This paper presents the results from research undertaken in the CSIRO-funded Mineral Futures Collaboration Cluster on developing a future vision for the mining and minerals industry – Vision 2040 – in which the industry proactively contributes to long-term benefit for communities and the nation. Our research finds that Australia is currently experiencing mining-led prosperity due to high commodity prices, yet underlying this are challenges for maintaining market share due to lower productivity from extracting lower grade, more remote and complex ores. Whilst much focus has been on developing new technologies for finding and processing such ores, this paper assesses these activities, together with policy and market innovations in the context of needing to strengthen social, environmental and financial capital for long-term benefit. Vision 2010 sees mining activities linked to systems that are net providers of clean water, energy and ecosystem services, rather than minimising negative impacts alone; sovereign wealth funds are used to harness current prosperity for future innovation. Using a case study in lithium and comparisons to iron/steel, coal and copper – we illustrate the opportunities for new technology, policy and market innovations to link the mining and minerals sector in Australia to more sustainable patterns of production, consumption and prosperity.

Nov 22, 2011

By H Masoumi, I Canbulat, Y Zhao, J Oh, H Lin

Borehole breakout is a drilling induced phenomenon caused by overstress of rock around the borehole. Its depth usually aligns with the minimum horizontal principal stress direction. For this reason, it has been used to determine stress orientations and a series of researchers also argued its dimensions can be indicative of stress magnitudes. If the stress dependencies of breakout geometries are well understood, it is possible to estimate stress magnitudes based on these data. This paper investigates the influences of critical parameters on breakout dimensions, including absolute stress magnitudes, stress ratios and borehole diameter. Several experiments have been conducted on cubic (120 x 120 x 120 mm3) sandstone samples with pre-drilled holes (22 mm and 30 mm) under true tri-axial loading conditions using UNSW self-designed equipment. Experimental results confirm the increasing maximum horizontal principal stress magnitudes result in larger angular span and longer breakout depth at constant minimum horizontal and vertical principal stresses. There is also a considerable discrepancy observed between experimental results and the analytical model. Findings of this study imply a potential on the estimation of stress magnitudes using borehole breakout. CITATION:Lin, H, Oh, J, Canbulat, I, Masoumi, H and Zhao, Y, 2018. Experimental investigation on borehole beakout and its implication on stress magnitudes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 266–273 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Jahn, M Noel, E M. Rykaart, M Pau

Three soil cover test areas were constructed on waste rock backfilled into the Lichtenberg Pit, near Ronneburg Germany. A fourth, uncovered area was included as a control. Each test area measures 50 m by 65 m, and was constructed using full-scale equipment and construction practices. Extensive material sampling and testing was included as part of the construction. Devices were installed in each plot to monitor meteorology, infiltration, run-off, interflow, soil moisture, soil temperature, and soil pore gases. Boreholes were completed in each area and instrumented for temperature, pressure and pore gas sampling to a depth of approximately 60 m. Data from the monitoring instruments have been collected since July 2000, and have been comprehensively analysed and modelled on two occasions. The paper presents an overview of the test area design and instrumentation and the results of the two comprehensive data reviews. The reliability of the various monitoring methods is discussed and experience with several innovative methods is reviewed. The difficulties encountered in modelling the data set using common soil physical models are discussed.

Jan 1, 2003