Search Documents

By N McIntyre, R Trancoso, N Bulovic

Mining is essential for facilitating human development particularly as demand for critical minerals grows. However, over the mine life cycle, the environment is permanently changed. Once mining ceases, mine-affected land can leave significant legacy issues on the surrounding environment if not managed. Therefore, mine closure planning is critical. Mine closure occurs over large scales often with the aim of recreating resilient ecosystems over mined landscapes with mitigated negative impacts. The natural state of the landscape and the environmental risks over planning time-scales are largely driven by climate. Climate change is expected to impact different parts of the post-mining landscape, from stable landform design (soil erosion mitigation) to revegetation efforts and pit lake management. Consequently, mine closure plans may need to account for a non-stationary and uncertain future climate, that may be both different to the current climate and evolve during the mine life and post-closure. Here a new data-based approach is presented for incorporating climate change projections in mine closure planning, based on the recently released Coupled Model Intercomparison Project phase 6 (CMIP6) climate data used in the latest Intergovernmental Panel on Climate Change (IPCC) assessment report. The approach: (i) characterises closure-related attributes of the future climate, and (ii) identifies the amount (and direction) of change expected to occur, and its uncertainty, focusing on five metrics for demonstrative purposes and initially describing changes in erosive potential below. This provides information on the type of future environment (ie the changing baseline) that mine closure should plan towards, and identifies rehabilitation options that may be susceptible to increased risks from climate change.

Aug 2, 2023

By J Harmse

This paper deals with the modernisation of the brakes on an electrically coupled Blair multi-rope hoist and covers the removal of the old calliper brakes and hydraulic control system, and its replacement with brake discs, disc braking units and hydraulic control systems. The paper covers the braking requirements of the hoist, which is made up of two electrically coupled single-drum hoists, together with the theory behind the choice of brakes and control systems supplied. The paper also covers the project logistics that were required in order to install and commission the new brakes and control systems with the minimum disruption to production on the only rock hoist on a major production shaft. Items covered include the modifications to civil works, pre-installation of bearing lubrication systems, brake discs and hydraulics and the interfacing of the new hydraulic control system to the existing electric control system. It had to be designed to be compatible to a new electric drive and control system due for installation at the end of 2005.

Jan 1, 2005

By Van Rooyen F

An introductory review of the current grade control blasting techniques (selective mining strategies) used in the Eastern Goldfields has recently been undertaken. The survey was initiated and conducted by the Western Australian School of Mines. Four distinct selective mining strategies have been identified and a number of trends have been highlighted. Many operations, however, have developed techniques which use a hybrid method to suit the site conditions. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and experiences no mixing of the various identified ore and waste blocks and is fully reco- vered at the minimum overall operating cost. Due to this unified aim all of the grade control blasting techniques have many common design Features.

Jan 1, 1988

By K L. Silversides, A Chlingaryan, A Melkumyan

Multiple data sources can be fused to improve boundary modelling in stratified deposits such as the banded iron formation (BIF) hosted deposits in the Pilbara Region of Western Australia. Accurate boundaries are essential to produce high quality geological models. Initial models are based on the widely spaced exploration hole data. This creates a high level of uncertainty in areas between the holes, with different interpretations of the boundary equally probable. Including directional information collected in these holes in the models can reduce the number of possibilities. Including data collected during mining, such as blastholes and bench measurements, can further guide the model. This research demonstrates a Gaussian Processes based method of fusing these disparate data sources to better inform the boundaries. Our results demonstrate that when only exploration points are used the model creates a smooth boundary with minimal variation between the holes. Each additional data source refined the model and added additional detail to the boundary. For the blast data, the new detail projects down to the bench below the current bench to allow for a better prediction before mining commences on that bench.

Mar 22, 2022

Gold deposits in Eastern China have characteristic of belted distribution. The concentrating belts of gold mineralization are about parallel to the island are belt in Western Pacific Ocean. Gold deposits are mainly concentrated in the aged metamorphic rock series on the upwarping zones and upwarping fault zones, and obviously controlled by the deep fractures and their deriva-tive secondary faults. Gold mineralization had genetic relation to the Mesozoic (especially Yanshan period) magmatic activity. The distribution and genesis of gold deposits can be explained by the assumption of wavy structure. The formation of wavy structure is related to the process of Pacific plate and India plate.

Jan 1, 1990

By T Martin, M Martin

Mining of sulfide-based ore deposits typically creates a potential for release sulfate and acid to groundwater, and many operating mines are thus predicted to require long-term post-closure treatment of groundwater. Toward the goal of selecting an optimal treatment, this paper compares costs of four demonstrated technologies for long-term treatment of sulfate-contaminated groundwater: in situ biological reduction (ISR), in situ permeable reactive barrier (PRB) composed of compost and zero-valent iron (ZVI), and two ex situ æpump-and-treatÆ technologies ù ex situ biological reduction, and ex situ nanofiltration with lime precipitation. Costs for each technology are estimated for treatment of a model aquifer system containing sulfate-contaminated groundwater, with the goal of treating 1 m3/min of groundwater from 1500 mg/L sulfate to a target level of 500 mg/L. (Metal removal is typically achieved by these technologies, and thus excluded from this analysis.) Costs are estimated for each technology as a function of treatment duration (ten to 60 years) and, for PRB and ISR, required replacement frequency (ten to 60 years). Estimated costs include capital and operation and maintenance, using a seven per cent net discount rate. Results indicate that ex situ technologies (biological reduction and nanofiltration with lime precipitation) are the most expensive. In situ technologies may be much less expensive, with PRBs having by far the lowest potential cost, followed by ISR as the next least expensive. However, actual costs for the in situ technologies are very sensitive to poorly constrained parameters, particularly the ZVI content of the PRB, and the effective life of PRB and ISR systems. This large cost uncertainty supports delaying remedial actions where viable, and suggests that feasibility analyses are generally warranted for specific applications to focus on these sources of uncertainty.

Jan 1, 2003

By D E. Ralph, D-J Kim, G-J Ahn, Y-H Rhee

The amount of discarded dry batteries are presently found to be increasing globally and waste cathode active materials of the lithium ion battery industry are among them. Hydrometallurgical operations are being applied to recover the valuable metals from these waste batteries. To find an economic and environmentally friendly process, the bioleaching process was applied in the present investigation for recovery of valuable metals. Its principle is the microbial production of sulfuric acid and simultaneous leaching of metals. Bioleaching of spent lithium ion secondary batteries, containing LiCoO2, has been studied in this investigation. A new method for recovery of cobalt, potentially the basis of an economic and environmentally friendly process was examined. The present study has been carried out using chemolithotrophic and acidophilic bacteria Acidithiobacillus ferrooxidans, which utilises elemental sulfur and ferrous ion as the energy source to dissolve metals from spent batteries. Bio-dissolution of cobalt was found to be faster than lithium. The effect of initial Fe(II) concentration, initial pH and solid/liquid (w/v) ratio were studied in detail. Higher Fe(II) concentration showed a decrease in dissolution due to co-precipitation of Fe(III) with the metals in the residues. Similarly, at higher initial pH values and higher solid/liquid ratio (w/v) metal dissolution was found to be inhibited. The optimised conditions for bio-dissolution were solid/liquid (w/v) ratio û 10 g/L, initial Fe(II) concentration û 3 g/L, elemental sulfur û one per cent (w/v) and initial pH û 2.5. In the optimised conditions, cobalt dissolution was observed to be about 60 per cent, whereas that of lithium was ten per cent after 20 days. A first order kinetic model was derived to study the rate of dissolution of both the metals.

Jan 1, 2006

By G Forbes, D J. Bradshaw, G S. Heinrich, D

Traditionally, operators on mineral flotation plants have relied on visual inspection of the froth surface when making adjustments to process set-points. Machine vision systems are being developed to relate froth surface descriptors, which can be consistently measured in real time, to flotation performance. By investigating the impact of various selected operating variables on both froth surface characteristics and metallurgical performance it is possible to develop a management strategy for the control and optimisation of the process. This paper presents the results of testwork conducted at Kennecott copper mine which investigates the relationship between the froth colour and the concentrate grade and discusses the factors which affect the froth colour. This work shows that the main factors that influence the froth colour in this system are molybdenum, copper and iron concentrate grade, pulp and concentrate per cent solids and pulp iron grade.It goes on to develop models to predict the concentrate grade based on colour information and velocity and stability information. It also shows that the most accurate prediction is made with combined colour and stability information.

Jan 1, 2005

The purpose, basic data requirements and various analysis/modelling tools employed for geomechanical evaluation of mine-site conditions are overviewed. The impact and application of computer technology are dis- cussed. Broad guidelines and criteria are presented for establishment of a practical geomechanics data-base system to yield infor- mation suitable for mine design purposes. Future needs of the Australian mining in- dustry are examined.

Jan 1, 1983

By A Sinuhaji, R Poedjono, G Flumerfelt

PT Freeport Indonesia is currently building the DOZ mine. It is a 25 000 tonne/day block caving operation which is scheduled to reach designed production levels by the fourth quarter of 2002. This paper describes some of the issues and challenges faced by the operation when introducing a new undercut method part way through the project. Advantages and disadvantages are discussed as well as the expected benefits of the new method.

Jan 1, 2002

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

By James D, Dawson N

The alternate mineral dressing tech-niques for the production of ilmenite roaster feed from heavy mineral concentrate and the reasons for the selection of wet high intensity magnetic separation (WHIMS) at Richards Bay Minerals are outlined.Initial flowsheet studies were under-taken using laboratory scale equipment followed by on site pilot testing. Flowsheet development culminated with an extensive test programme conducted at Readings of Lismore in 1975.

Jan 1, 1986

By Donchak PJ, Lang SC, Hammond RL, Bultitude RJ

The Hodgkinson and Broken River Provinces form the northern part of the Tasman Orogen. They are separated by a broad belt of Late Palaeozoic igneous rocks, but were probably originally continuous. They are bounded to the west by a system of major faults (Fig. 1) which separate them from the Georgetown Province. Although largely Precambrian, the Georgetown Province includes probable Siluro- Devonian granitoids, and in the south adjacent to the Broken River Province, metamorphosed Early Palaeozoic(?) volcanics and sediments of the Greenvale Subprovince. South of the Broken River Province, the Lolworth-Ravenswood Province includes probable Precambrian rocks, Cambro-Ordovician volcanics and sediments, and voluminous Ordovician to Early Devonian granitoids. The first systematic studies of the provinces were the 1:250 000 scale mapping programs by the Bureau of Mineral Resources and Geological Survey of Queensland (White, 1965; de Keyser and Lucas, 1968). These and subsequent regional studies were reviewed by Arnold and Fawckner (1980). Remapping by the Geological Survey of Queensland since 1982, and a concurrent regional study of the deformation by Hammond (1986) have provided much new data. We acknowledge the contribution of other members of the GSQ field parties - L. Cranfield, J. Domagala, B.G. Fordham, P. Green, R. Halfpenny, R. Hegarty, L. Hutton, S. Law, D. Macansh, T. McLennan and M. Scott.

Jan 1, 1987

This paper describes the new iron and steelmaking process recently commissioned at NZ Steel. Ironsand mined and concentrated at Waikato North head is slurry pumped 18 km to the company's Glenbrook works. Ironmaking includes the direct reduction process pioneered at Glenbrook in the 1970s and a new continuous electric melter. The molten, high carbon pig iron produced is then fed to a vanadium recovery unit and on to the KOBM oxygen steelmaking vessel. Steel is cast into billets or slabs. The new plant, which is the first stage of a fully integrated works at Glenbrook, raises New Zealand Steel's production capacity from 150 000 t/y to 750 000 t/y.

Jan 1, 1986

By G T. Hefter, P Singh

The effect of using SO2 as an anodic depolariser in the electrowinning of copper from aqueous acid sulphate solutions has been studied using cells without/with a ceramic diaphragm. In all cases SO2-saturation of the electrolyte/anolyte decreased the anode potential by 68 to 75 per cent largely due to a change in the anode reaction from the oxidation of water to the oxidation of SO2 . However, poor quality deposits and low current efficiencies are encountered if SO2 is allowed free-access to the copper being deposited at the cathode. This situation is easily avoided by using a diaphragm to restrict SO2 to the anode compartment and for these conditions the resultant copper deposits are of a similar (high) quality to those obtained in the absence of SO2.

Jan 1, 1999

By W Wu

The prospect of discrete element modelling (DEM) being used as an everyday design tool for transfer chutes in the iron ore mining industry is becoming more and more probable. However, much care needs to be taken to ensure accurate results are obtained. Whilst there are many publications in industry portraying the potential of DEM, there is little evidence of where it has been validated against a real set of experimental results. The purpose of this investigation was to gauge whether the incorporation of the physical properties of a specific bulk material at the DEM pre-processing stage can yield visually and numerically accurate simulations for a simple flow case. Effects such as irregular particle shapes, varying frictional properties and coefficients of restitution, all found through experimentation were investigated. Video analysis was used to compare simulations to real flow cases. It was found the most critical attributes in determining the accuracy of the simulations were particle shape and wall friction. Keeping the particle-to-wall friction factor constant was not sufficient to describe the flow accurately. But by introducing the varying effects of wall friction with consolidation stress, the correct results were simulated.

Jan 1, 2007

By M Kuruppu, B Besa

Currently, conventional methods of decline development put enormous cost pressure on the profitability of mining operations. This is the case with narrow vein orebodies where current methods and mine design of decline development may be too expensive to support economic extraction of the ore. The time it takes to drill, clean and blast an end in conventional decline development can be up to 473 minutes. This is because, once an end is blasted, cleaning should first be completed before drilling can commence, resulting in low advance rates per shift. Improvements in advance rates during decline development can be achieved by application of the electric monorail transport system (EMTS) based drilling system. The system is composed of a two-boom drill mounted on the monorail and a pneumatic face cleaning system that loads blasted material into monorail containers. The operation allows for drilling of the top part of the face to commence as the monorail loading system continues to clean the blasted material at the development face. The preliminary indication is that an advance rate of 12 m per day could be achieved compared to 6 m per day in conventional decline development. The increase in the advance rate results from increased number of blasts that are possible per shift due to reduced time of cleaning and drilling the development face. The continuous drilling system has the advantage of accelerated decline development and orebodies will be accessed quickly and cheaply. Other advantages of the system include negotiating steep and changing gradients (ie reducing decline length), ability to negotiate tight horizontal curves, small operating room and limited diesel fumes.

Jan 1, 2008

Tertiary laterite is extensively developed in the Darling Range area, but there is doubt that. the high relief areas along the Darling Scarp have been peneplaned. Three distinct laterite types are distinguished which are termed transported, introduced and residual laterites to avoid ambiguity. Transported laterites are recemented (primarily) lateritic materials and introduced laterites are chemical deposits of bog iron type. Residual laterites are formed in situ from the host material which can be either decomposed bedrock or detrital' clay, and the two varieties formed from these sources are termed residual A and residual B laterites. The genetic requirements for residual laterite formation are (1) host material, (2) porosity and permeability, (3) rainfall, (4) temperature, (5) relief and drainage, (6) vege- tation and (7) time. Previous theories on the origin of laterite appear to be inadequate and incompatible with field observations. Field investigations and drilling in the Darling Range area disclosed lenticular section and thickest laterite development on slopes and thin or oc- casionally no laterite development on crests. Lateritisation is considered a surface feature and the end product of the chemical weathering cycle. The relief and rain-water acting on a kaolinitic host material are con- sidered the major contributing factors in the

Jan 1, 1973

By Xianguo C, Baoqi S, Shaozhong Z, Huiling Z, Zhengbing C

Acidless and fluoless flotation is a new method for separating feldspar from quartz at the natural pH value of tap water in the absence of any acid and fluoride and other inorganic reagents. The paper introduces the production application of this method in plants and research results on the mechanism involved in the flotation method.

Jan 1, 1993

By M B. Lovitt

At present there exist few engineering calculations and principles to determine exclusion zones for personnel in the vicinity of underground explosive storage areas. This paper is written to encourage discussion and proposes a method to determine the impact of a blast wave through scientific principles. Then, criteria to determine an ‘exclusion zone’ need to be identified.There has been much work on identifying the pressure rise and the energy of explosive detonations underground but little to develop standards in criteria that can be used to identify exclusion zones for useful design of underground infrastructure. The author presents the newest ways of calculating the pressure rise and energy (impulse) of detonations and puts forward some criteria to be used in the identification of personnel exclusion zones to spark peer review and discussion of these criteria towards developing standards for engineering design.Smith and Sapko (2005) used Sach’s scaling laws to develop a relationship for both pressure rise and impulse, which incorporated factors for intersections. Intersections will have a large bearing on the peak pressure and the energy of the blast wave and needs to be incorporated. Silvestrini, Genova and Leon Trujillo (2009) developed the scaling laws with an energy concentration factor to predict blast propagation in partially confined geometries and together the author has proposed equations for determining the peak side pressure and the impulse in a tunnel. Given the weight and type of the explosive, the average cross-section of the tunnel complex and the number and type of intersections encountered, the pressure and impulse can be calculated.The military has carried out many investigations as to the influence of blast pressure and impulse on the human body. Lung damage, ear damage and velocity knock down are three of the criteria standards that are presented as possible methods of determining exclusion zones around an underground explosives magazine. The author suggests that the velocity curves presented by Bowen, Fletcher and Richmond (1968) could be an acceptable method of determining an exclusion zone as it incorporates the side pressure and the energy of a blast wave to determine the ability of the wave to knock down personnel.CITATION:Lovitt, M B, 2014. Exclusion zone calculation for underground explosives storage, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014