Search Documents

Outsourcing of mining operations and services is done for various reasons and there is no single model which fits all situations. Experienced contractors and mine owners have also developed, more often than not, jointly, numerous commercial arrangements and project delivery methods to suit their particular project. It is often the case that some mine owners who have not considered outsourcing to contractors do so because of a simple lack of understanding of the potential benefits. This paper will highlight the potential benefits and perceived disadvantages of outsourcing for mine owners and demonstrate how these issues have been addressed by the mining contracting community over recent times as well as demonstrate the evolution of current commercial arrangements in engaging mining contractors.

Jan 1, 2006

By N Johansson, D Johansson, A Beyglou, H Schunnesson

As demand for optimisation of mining processes increases, more attention is drawn to blast performance and fragmentation improvement. Fractures and discontinuities are among the most influential factors in blast results, therefore one of the initial steps towards blast optimisation is to gather information about the rock mass and integrate it in blast design. This paper presents a method for assessment of rock mass discontinuities and integrating it in production blasts in the Aitik open pit copper mine in Sweden.3D photogrammetric techniques were utilised to map discontinuities and distinguish domains of similar geologic structures in the pit. As a pilot study for a future campaign, four different initiation directions were tested through six pilot blasts in one of the domains. The results were compared in terms of swell and loading efficiency of rope shovels to identify the correlation between blast performance and initiation direction compared to major discontinuity families.It was established that in the trial domain, blasts initiated towards north or north-west yielded larger swell and better performance of loading. Comparing these blasts with discontinuity families show that there is a correlation between blast performance and initiation direction according to the dip and strike of these discontinuities. Such knowledge can be used for future blasts in the same domain to increase long-term operational efficiency through slight modifications in drill pattern and initiation design.CITATION:Beyglou, A, Schunnesson, H, Johansson, D and Johansson, N, 2015. Adjusting initiation direction to domains of rock mass discontinuities in Aitik open pit mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

By M I. Roberts

Corporate and workplace culture, as many owners, directors, executives and managers know, is by far the most powerful determinant of productivity. It’s much more significant than buildings and equipment. Yet although no one today would build a building or machine without a plan, few leaders have a plan for building and sustaining a safer and more productive culture.Using practical ways, culture can be planned and shaped as desired. Success requires implementing a project plan for changing the systems that drive behaviours that in turn shape attitudes. The combination of behaviour and attitude together with leadership largely shape culture.To improve performance, leaders need to:1. improve the organisational systems that drive behaviour2. action a project plan for improving specific performance metrics 3. demonstrate leadership that is conscious, disciplined, committed and passionate for purposeful use of human energy.This paper explains all three factors in practical ways with operational and corporate examples. It details understanding and applying the power of fundamental statistical analysis tools to recalibrate, focus and drive proactive leadership that takes responsibility for process improvement, supporting people and ensuring accountability.Experience and practical understanding of human and organisational behaviour confirm that the Measurement ? Analysis ? Reporting system combined with conscious leadership is by far the most powerful driver of behaviour. This wisdom produces profound changes in leadership style and behaviour. It develops outstanding leadership to create and sustain a safe and highly productive culture reliably producing consistently high quality products. It is the key to developing accountability, employee retention and a sustained competitive advantage.CITATION:Roberts, M I, 2016. Building safe, productive cultures and leadership, in Proceedings International Mine Management Conference, pp 163-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By B T. Park, S D. Fundingslan, K W. Wangerud

The EPA National Risk Management Research Laboratory (NRMRL) Mine Waste Technology Program (MWTP) and the EPA Region VIII Superfund office are jointly conducting a field-scale technology demonstration of a two-step in situ treatment of the acidic Anchor Hill Pit lake at the Gilt Edge Mine Superfund site near Deadwood, South Dakota, USA. The project goal is to develop cost and performance data for the in situ treatment for potential application in long-term water treatment/management activities at the Gilt Edge site, and for potential application at other similar sites. Lime neutralisation of the pit using a Neutra-Mill was accomplished in the spring of 2001, with a resultant lime utilisation efficiency of about 71 per cent, and a typical throughput of about 1 tonne per hour using coarse, pebble quicklime and 1.4 tonnes per hour using finer, ground lime. Redox-mediated biotransformation treatment of the pit has been ongoing since May 2001. As of January 2003, denitrification is complete in the near-surface waters and about 90 per cent complete in the deeper waters. Bacterial sulfate reduction is expected to begin in the near future. This paper describes project activities, results, and lessons-learned to-date as well as future monitoring plans.

Jan 1, 2003

The recovery of Copper by solvent extraction was arguably the most significant hydrometallurgical development of the 1960's. However, only dilute solutions at relatively high ph. could be treated effectively. ICVAcorga introduced in the 1970's the much stronger salicylaldoxime based reagents, which resulted in a dramatic change in plant configurations. So for example plants which normally use 3 extraction stages and 3 stripping stages could be reduced to 2 + 2 staging or 2 + 1 staging, even for high copper tenors at low ph. Leach liquors up to 40 g A copper are being treated at some locations so that almost any copper bearing liquor can now be purified by solvent extraction. Following a considerable amount of research and development effort ICI/Acorga have made further significant advances in the application of copper solvent extraction. The first of these is in computerised flowsheeting. In conjunction with ICI's Process Technology Department, Acorga have developed the Minchem Computer program, which uses laboratory generated equilibrium data to facilitate optimisation of metallurgical operating parameters. The program can operate in two modes, prediction and assessment so that given suitable extract and strip isotherms plant performance can be predicted for a given set of conditions. Alternatively existing plant performance can be assessed rapidly and accurately, thus providing a valuable quality control tool. Pilot plant work can now be restricted to evaluation of the physical aspects of the SX circuits, and to looking for the unexpected. Secondly using the patented 5-Nonyl Salicylaldoxime in precise admixture with a number of carefully selected strip modifiers, the Acorga M-range has resulted. Reagent selection from these new extractants can now be based on how the reagent can alleviate the remaining problems such as hydrolytic stability, transfer of iron, and organic losses by entrainment which may be related to particular features of the operating plant. Thus the Acorga M-range has enhanced and significantly extended the use of solvent extraction for copper, whilst refinements in the processing of metallurgical data has considerably simplified circuit design and analysis of results.

Jan 1, 1989

By D Henderson, K Howie

In 2005, Glass Earth Limited (GEL) commissioned two large area detailed airborne geophysical programmes in the Taupo Volcanic Zone (TVZ). In the first survey Bell Geospace Ltd of Scotland conducted an Air-FTG« (airborne Full Tensor Gravity Gradiometry) survey covering 2338km2 at 300m line spacing. The second survey by UTS Geophysics, Australia included detailed airborne magnetic, radiometric and digital terrain data capture covering 5341km2 at 150m line spacing.   From the detailed geophysical data collected it is possible to identify major deeply penetrative crustal structures within the TVZ, as well as define subsurface geological features, such as intrusive bodies and alteration zones. These major deep crustal structures are thought to have a controlling influence on the distribution of epithermal gold mineralising systems, and along the corridors defined by these deep crustal zones, the chances of discovery of an economic epithermal gold discovery are greatly increased.   In this paper GEL gives some examples of the application of its integrated data driven approach to exploration in the TVZ at both regional and project scale. The paper focuses on how GEL identifies regional scale highly prospective deep crustal structures. Then, using the Horohoro epithermal gold system as an example, we show how GEL applies innovative geological and geophysical data processing to model and understand detailed subsurface geology, focusing subsequent exploration to ensure the best opportunity for a new economic epithermal gold discovery.

Jan 1, 2007

Portman Mining Pty Ltd very successfully operated the Ferro GullyNorth Mine in the Hamersley Province of Western Australia to satisfy a contract for the delivery of six million tonnes of iron ore in less than two years to the Mount Newman Mining Co Pty Ltd. The high-grade ore extracted from Ferro Gully North Mine was unusual in that, not only was it within the Joffre Member of the Brockman Formation, but it was rich in red ochreous hematite and martite and very low in phosphorus.

Jan 1, 2001

By Y Peng, B Guo

In gold processing plants, the water from the cyanidation stages is treated to detoxify cyanide species and this recycle water becomes the main part of the process water. Despite the low concentration of free and weak acid dissociable (WAD) cyanides in process water, the recoveries of gold and silver is still affected during flotation, especially when gold and silver are associated with iron sulfide minerals. This is a case at the Hidden Valley (HV) Mine. In this study, the effect of free and WAD cyanides on gold and silver recoveries by flotation from the HV Mine was considered.WAD cyanide (WAD CN) was prepared by mixing sodium cyanide and copper sulfate at a cyanide to copper ratio of 3:1 dosed at different cyanide concentrations. It was found that both free and WAD CN depressed gold and silver and particularly iron sulfides in flotation. The depressed gold and silver recoveries were closely associated with the depressed recovery of iron sulfide minerals, suggesting that free and WAD CN may not depress the flotation of liberated gold and silver minerals significantly. It was also found that 10 ppm free cyanide completely depressed the flotation of iron sulfide minerals and WAD CN depression is probably through the WAD dissociation to free cyanide species (mainly aqueous HCN) during the grinding process, resulting from a decrease in pH. Thermodynamic calculation showed that 5.5 ppm free cyanide was released in the end of grinding at an initial WAD CN concentration of 50 ppm. This research provides a guideline to counteract the negative effect of WAD CN in the flotation of gold and silver minerals.CITATION:Guo, B, Peng, Y and Espinosa-Gomez, R, 2013. The effect of weak acid dissociable cyanide on gold and silver flotation in Hidden Valley Mine, in Proceedings World Gold 2013 , pp 341-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By F Musa

One of the main energy efficiency opportunities identified from the majority of mine site energy audits is to optimize the comminution circuit to reduce energy consumption through improved throughput and product size distribution. Typical analysis reviews comminution process efficiency/inefficiency i.e. utilization of grinding mills, process bottlenecks and product vs. target size, to identify instances of overgrinding or undergrinding. From this, it is possible to establish the potential improvement that could be gained through formal plant optimization and what the optimization program would entail. It can also sometimes reveal immediate opportunities for process improvement. This paper presents steps that can be taken to optimize the efficiency of comminution circuits.

Aug 8, 2011

By F H. Henrfquez, A G. Oroz

Design and operating conditions of large size mechanical flotation cells were evaluated by comparing them with actual operating conditions in a plant. The objective was to determine the time scale-up factor, typically based on empirical rules. Experiments were conducted on the rougher flotation circuit at Minera Escondida Ltd. The circuit consisted of self-aerated mechanical cells of 160 m3, arranged in six parallel banks with nine cells each. The rougher circuit flotation kinetics were evaluated from direct sampling and local mass balances around each cell of the bank. Adjusted overall mass balances were also developed. This information was used to fit different kinetic flotation models, and it was found that the rectangular distribution function was the most appropriate to describe the distributed rate constant for industrial operation. Then, a rougher flotation simulator was developed to describe the actual operation in terms of the operating variables (mass flowrate, solid percentage, feed grade) and the actual volumetric flowrate entering to each cell. In this study feed pulp samples were taken in parallel from the rougher circuit and were simultaneously floated in the laboratory. The kinetic behaviour was then modelled at a laboratory batch scale in order to determine the time scale-up factor between laboratory batch flotation data and industrial size flotation. The time scale-up factor observed for large sized cells, 160 m3, was found to be reasonably similar to those previously determined for self-aerated mechanical cells, but of lower size, operating at similar recoveries. In addition, the relative effect of mixing, between laboratory batch and an industrial flotation bank, was quantified by the parameter, separating the impact that kinetic and mixing changes have on the time scale-up factor. In general, the rougher flotation operation was found to reach the predicted metallurgical target, and the optimal separability criterion was also respected. The diagnostic generates information about the internal state of the process and helps to identify potential improvements for design, operation and control of the circuit.

Jan 1, 2005

Conventional narrow vein mining, utilising hand held methods, is expensive and requires specialised miners who are becoming a rarity. Hand held mining techniques (shrinkage stoping, leading stoping and cut and fill) have the advantage that they can be selective. The methods allow continued sampling of the face, control of hanging wall conditions and are adaptable to changes in strike and dip. On the other hand, more productive longhole stoping methods can allow excessive dilution due to drill hole deviations and changes in orebody dip and can be subject to unexpected hanging wall or footwall failures. Development of small scale equipment (as narrow as 0.8m wide) used for drilling or bogging very smallaccess drives has been ongoing over the past decade. In this paper, types of equipment are examined and compared, particularly with respect to their produc- tivity, size, and working environment. The introduction of electric hydraulic equipment has provided a better working environment with reduced noise, exhaust fumes and heat. The concept of the "hydraulic cherry picker" may have application in mining steeply dipping orebodies. The system requires orebodies to be reasonably consistent in dip over 15 metre sub-level intervals. The system involves the basic concept and skills of machine and airleg mining, combined with the safety and productivity of a mechanized work platform. The platform or basket is stabilized between the hanging wall and foot- wall by hydraulic rams and is extended by a tilting hydraulic boom mounted to a small prime mover or trailer. Design concepts (including remote controlled charging of explosives, adaptation to the boom for rock cutting and the overall electric hydraulic mining concept) are put forward in the paper as a view as to how narrow vein mines will be mined in the future.

Jan 1, 1987

By B Yeganeh, A Sam, A Kohsari

The base of separation at Gol-e-Gohar iron ore plant (Sirjan in the south of Iran) is magnetic separation after milling. Magnetic separation in the plant is divided into two parts: dry magnetic separation and wet magnetic separation. Sixty-five per cent of the plant production belongs to the dry magnetic separator section. Therefore, investigation of this part of the plant is necessary. Prediction of plant production is one of the most important subjects in mineral processing plants. That means, before feed enters the plant, specification of production has been calculated with laboratory methods. The purpose of this paper is the prediction concentrate quality has achieved from the dry magnetic separator. The content of iron in the final dry concentrate will be predicted, with laboratory, pilot and modelling methods, before feed enters the plant. Different variables are used in this approach, which consist of: speed of the first dry magnetic separator (rougher), speed of the third dry magnetic separator (cleaner), iron content in plant feed, size of 80 per cent passing of feed, size of 20 per cent passing of feed and iron content in pilot dry magnetic separation concentrate that performs in a standard manner. The artificial neural network is used for modelling and one of its branches is the radial basis network (RBN). Iron content in magnetic separating concentrate in plant will be introduced as the target and will be calculated with the RBN method. In the RBN method, a set of data enters to neural network and they will be trained and simulated. Finally, the target will be predicted. Ultimately, the original target (actual iron content) and the predicted target (predicted iron content) compare and error of them will be calculated. The obtained result is acceptable and satisfactory.

Jan 1, 2007

By S Brown

With oxygen conditioning routinely used in both the lead and zinc circuits at Pasminco Elura Mine a more sophisticated method of determining oxygen demand was required. It is known that different ore types have different oxygen consumption rates, however oxygen is added at a fixed rate regardless of ore type in the plant. Therefore, a simple laboratory test was devised to measure the oxygen demand of ores. The paper describes the technique employed, and provides an interpretation of the results. These data, together with pulp chemical measurements (Eh, pH and EDTA extraction data) were correlated against laboratory flotation performance to establish the relationship between oxygen demand and the position of the grade/recovery curve.

Jan 1, 2000

By S Shafiee, N Abbate

The evaluation of mining projects requires a methodology that will give flexibility and manage the existing uncertainty within the projects. The discount cash flow (DCF) and other traditional evaluation approaches, which are widely used in evaluating a significant number of mining projects, have simply assumed that the main variables remain constant in their evaluation; elements such as discounted rate, mine life, operating cost and production rate. The DCF ignores managementÆs flexibility to adapt and reforecast and revise decisions. Real options valuation (ROV) is one of the modern evaluation methodologies that provide a tool to adapt and revise mining projects under uncertainty and future variables movements. ROV brings more variables into the evaluation model compared to DCF and assumes them as uncertain and dependent. Finally, ROV provides a range of solutions that can assist in managing this flexibility.This paper endeavours to compare ROV and DCF for mining projects comprehensively and applies these two techniques in the model. The paper shows that ROV will be inclusive of extra value in mining projects due to variables not allowed for, or even ignored, when the DCF model alone is used. One of the significant advantages of the ROV method is being able to evaluate mining projects under different scenarios from the inception of the projects. Furthermore, ROV gives the ability to evaluate the mining project while allowing for abandonment, temporary suspension, or expanding the mining project. In other words, the ROV evaluation process creates an analytical environment, which allows for optimisation of the mining plan within the mining project, as well as the ability to change the capital structure dependant on existing circumstances over the life of the project. The ROV is a new evaluation method that can add value in mining project analysis and offers opportunities to amplify gains, or to mitigate losses. This paper also discusses some of the reluctance to use ROV instead of DCF in current project evaluation.CITATION:Shafiee, S and Abbate, N, 2012. Now, this is the time for mining companies to choose - Real option valuation or discount cash flow, in Proceedings Project Evaluation 2012 , pp 225-234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By A D. Campbell

Conversion of Mineral Resources to Ore Reserves requires a multidisciplinary approach and application of a number of Modifying Factors. The Modifying Factors for mining, particularly dilution and recovery in a caving mine are complex and can be difficult to determine. Cave flow modelling software is widely used for mine planning, scheduling and forecasting metal production. However, the conversion of Mineral Resources to Ore Reserves remains a difficult and subjective process and a consistent approach to convert Mineral Resources to Ore Reserves as part of the cave flow modelling process is not published in the literature. This is due to the difficulty in estimating the Ore Reserve that remains as cave stocks at a particular point in the mine schedule, the recovered tonnage and grade of the diluting material at various stages in the mine life, as well as the Mineral Resource classification of both the recovered and diluting material that forms the Ore Reserve. The key principle of this paper is the tracking of the Mineral Resource classification in the flow model used to estimate the Ore Reserves. This is critical to defining the Ore Reserve as Proved or Probable and enabling transparency in the reporting process. An approach for dealing with mineralised external dilution in the Ore Reserve estimation process is also provided.This paper outlines the approach to convert Mineral Resources into Ore Reserves developed at the Ernest Henry mine sublevel cave (EHM SLC). The same method could be used in any cave mine and applied at any stage of the mine life. The process replaces broad-brush assumptions for the mining Modifying Factors, such as dilution and recovery, as these are determined numerically as part of the model computation. This paper explains the Ore Reserve estimation method with a worked example to enable the reader to adopt the process at any caving mine. Mineral Resource classification within the block model is embedded in the cave flow model and the flow model results used to attribute tonnes, grade and the mixed proportions of the Mineral Resource classification for material extracted from each drawpoint. This information is then used to convert planned mine production into the appropriate Ore Reserve classification. Since the flow model simulation follows the mine schedule, it can be used to predict depletion and cave stocks at any stage of the mine life, and can calculate a residual block model at the end of the mine life. The accuracy of the flow model is checked by validating the forecast ore grade and metal tonne with reconciliation data from the concentrator which is also used to calibrate the flow model.CITATION:Campbell, A D, 2017. A simple and accurate method for Ore Reserve estimation and Mineral Resource depletion in caving mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By B Vorster, T Medhurst, A Huey

Roof conditions at Oaky North Mine can be prone to stress related damage and/or time dependent degradation. The ability to identify these areas prior to mining has proved challenging using traditional methods. To help alleviate this situation, a study was initiated to investigate methods for roof characterisation using geophysical logs. This involved the use of neutron log data to provide an indirect measure of the proportion of carbonaceous/micaceous laminae present in the immediate roof strata. Detailed analysis of the shale–porosity inter-relationships arising from this analysis provided a means to estimate the proportion of laminations for a given roof interval. This paper outlines the process and how it was used to improve the current GSR modelling and hazard mapping process.

Nov 29, 2022

By Laxaminarayan Holla

Significant coal reserves in New South Wales lie underneath major bodies of natural and stored surface waters. In order that mining can occur safely and without any adverse effect on the surface, various statutory provisions and administrative guidelines have been framed for regulating the surface and sub-surface strata disturbance. There are particular bases for the existing guidelines and the assumptions which were made in their choice. Evaluation of the guidelines in the light of the knowledge gained during the last ten years indicates that they are conservative in some cases and can be made less restrictive without lowering the safety standards. The suggested changes include reduced width for pillars in both bord and pillar first workings and panel and pillar workings, and increased level of extraction for a given degree of subsidence. Changes, if implemented, would lead to increased coal recovery.

Jan 1, 1987

By N Redwood, N Fowkes, A Bassom, S Durkin

"It is well known that from time-to-time a vehicle will interact with a bund or windrow and often the barrier is insufficient to safely arrest that vehicle. The result of such an incident is often catastrophic. Regulations around the requirement for edge protection near pit edges vary between jurisdictions. Generally in Australia regulations tend to be around placing the responsibility on the mine operator to provide ‘adequate’ or ‘appropriate’ edge protection. Guidelines often place a minimum height of bund at between half and two-thirds the diameter of the largest tyre on-site.Safescape has identified the opportunity to improve safety in open pit edge protection and is currently developing the Edge Protector (EP) product. The EP is designed to create a vertical front face to a conventional broken rock safety bund. The fundamental premise of the product is that by creating a vertical front face to the bund, trucks cannot easily drive up over the bund and instead have to push through the rock to get to the other side.In addition to providing a safer system for arresting vehicles, the vertical front face also means that extra space is made available in the haul road. This can either be used to facilitate larger trucks or when designing a new mine, with an increase in overall pit slope.This paper outlines the research and development of a new edge protection product. Discussion will include project objectives, economic incentive for mines to apply the system, mathematical analysis of the truck/bund interaction and physical testing of the product.Citation:Durkin, S, Fowkes, N, Redwood, N and Bassom, A, 2016. Innovative Approach to Open Pit Edge Protection, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 138–149 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Toussaint LF

A brief history of the mineral sands industry is given from a radiation protection standpoint, with gamma radiation and inhalation of radioactive dust being identified as the main sources of radiation exposure of persons working in the plants. The principal sources of gamma radiation exposure are identified and the history of early bagging methods is discussed. The concept of ALARA is introduced and the impact of the "bulka bags" (and more effective monazite storage facilities) are detailed as illustrative examples of dose minimization, together with the requirements for the transport of monazite. The dose from radiation received from inhaled dust is dependent on a number of parameters of the dust, some of which are not well known. ICRP 30 (1978) makes recommendations relating to the intake of radionuclides by workers. These recommendations are discussed with respect to the inhalation of dust containing thorium. The possible pathways of radioactive material throughout the body are also described. The effect of having parameters that differ from ICRP 30 is discussed and suggestions are made relating to measurements that can be carried out to more accurately determine these parameters. Since in some instances the exposures to dust yield personal doses which may exceed the annual ICRP 30 based limits, it is necessary to define more accurately parameters of the dust so as to determine more accurately personal Doses.

Jan 1, 1986