Search Documents

By A Golev, G Corder

The concept of the circular economy has been gaining traction both in Europe and China.In Europe the Ellen Macarthur Foundation see their mission as accelerating the transition from a linear take-make-dispose economic model to a circular model that is restorative and regenerative by design, and aims to keep products, components and materials at their highest utility and value at all times. The Chinese Circular Economy initiative is effectively a sustainable consumption and production program utilising cleaner production, industrial ecology and life cycle management approaches to meet the national challenges of maintaining rapid economic growth while simultaneously enhancing environmental quality and maintaining social progress. A key characteristic of both of these circular economy initiatives is to design out, reuse or minimise the generation of waste.The mining sector, by definition, is represented by linear rather than circular activities, by supplying resources to society. However, being one of the world’s largest waste generators, the sector can adopt similar logic to that of the circular economy to improve its sustainability performance. Waste is a critical issue along the whole metals value chain, from mining waste to eventual end-of-life products, such as scrap steel from construction and demolition waste or the growing problem of electronic waste.CITATION:Corder, G and Golev, A, 2016. Can mining be part of the circular economy or is it squaring the circle?, in Proceedings Life-of-Mine 2016 Conference , pp 121–123 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

By G B. Smith, G M. Marshall, A Querzoli

The South Australian mining regulatory framework has adopted a performance based approach to the management of risk. This approach has been in place in South Australia for more than 10 years and is increasingly being implemented in mining jurisdictions in Australia and around the world. Performance based regulation focuses on setting appropriate environmental outcomes to be achieved based on an assessment of the potential impacts associated with the development, operation and closure of mining projects. Measurable compliance criteria, including completion criteria, are set to demonstrate achievement of the outcomes. It is the responsibility of the proponent to propose designs and strategies that will achieve the regulated environmental outcomes and to demonstrate the implementation of their designs and strategies will achieve the outcomes into the future. Tailings Storage Facilities (TSFs) are significant elements of many major mines and each is unique with site specific factors such a materials to be stored, design, size, location, climate, sensitive receptors, operating history of the facility (i.e. changes to design), site culture and company capability amongst a range of other factors. Consequently a fit-for purpose approach is a key principle of best practice regulation of tailings management as it takes the site specific factors into account in setting appropriate outcomes for mitigating the identified impacts associated with a proposed development. Achievement of those outcomes through fit-for purpose, well designed management strategies would ensure safe, stable and economic storage of tailings in a manner that complies with all legislative requirements and presents negligible public health and safety risks. Tailings storage must also have acceptably low social and environmental impacts, both on and off site, during operation and indefinitely post closure. Achievement of environmental outcomes during operations and at mine completion can then be demonstrated to the regulator and community through public reporting of compliance with measurement criteria which establish the appropriate level of impact for each individual operation. A number of new mining proposals including tailings storage facilities (TSF) have recently been assessed and approved in South Australia. The location, size, design, sensitive receptors, public interest and therefore risk profiles of these TSF’s have varied substantially between these new mining proposals. These considerations were reflected in the assessment of the TSFs and the resulting mining lease conditions of approval including the environmental outcomes to be achieved over the life of the facilities. This paper and the accompanying presentation will provide case studies of recently approved TSFs within South Australia and the regulatory framework for each case.CITATION:Smith, G B, Querzoli, A and Marshall, G M, 2018. Tailings regulation – a South Australian perspective, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 166–177 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D Whitworth

The Golden Pig mine has embarked on a diamond drill program design philosophy that increases flexibility of the program by greatly increased drill pattern densities. The use of standard broad pattern diamond drilling at the Golden Pig mine has previously lead to operational inefficiencies and impacted significantly on the costs of the mine. The diamond drill program philosophy and its interaction with mine planning is explained. The case study of the E lode mining as used to internally justify the increased drill densities is detailed.

Jan 1, 2002

By H Benzer

Grinding clinker to finished cement consumes more energy than any other comminution process. World production of cement in 2009 was 2840 million tonnes and the energy required for comminution was 40-60 kWh/tonne depending on the clinker characteristics and the fineness of the finished cement. Machines used include single and multi compartment ball mills, HPGRs, vertical roller mills, centrifugal air separators, V separators, screens and crushers. The circuit most commonly used consists of a closed circuit HPGR followed by a single compartment ball mill and an air separator, and in operation the variables are adjusted to obtain maximum throughput with no loss of quality of the separator fines.A common objective in cement plants is to reduce energy consumption without affecting the particle size in the finished cement and simulation is used as one procedure to achieve this. Models are now available for all the machines commonly used in clinker circuits and circuit optimisation studies using simulation have been carried out in many plants leading to decrease in energy consumption per tonne of cement. In this paper the models used will be discussed briefly and several case studies will be reviewed which will highlight the effect of change in ball size in a two compartment mill, the role of the HPGR in an HPGR – ball mill – air separator circuit, and the use of a high intensity vibrating mill for producing finished cement with high additive ratio.

Aug 8, 2011

By T W. C Stambolie

Longwall mining is a form of underground mining and the principal extraction method for underground coal mining in Australia. The method is used in the mining of both thermal and metallurgical coal. The primary market for thermal longwall mines is that of the export market where price is governed against the Newcastle Thermal Benchmark index (globalCOAL, 2016).Australia’s thermal coal export outlook is considered moderate due to slower demand from major importing countries, as well as slowing domestic production. However, ‘Australia is projected to increase its share of world thermal coal exports and become the world’s largest exporter over the medium term as lower prices, increased domestic use and infrastructure constraints limit growth from other key suppliers’ (Office of the Chief Economist (OCE), 2016, pp 25, 58). On the contrary, and as a result of current global coal price trends, the basic economic principles of underground longwall coal mining are heavily stressed. From a life-of-mine perspective, influencing return on investment is at its greatest during project evaluation and execution. Appropriate and realistic economic assessment is paramount to ensuring the right outcomes are achieved under the current economic challenges.CITATION:Stambolie, T W C, 2016. Thermal coal industry – is longwall mining currently a life-of-mine option in Australia?, in Proceedings Life-of-Mine 2016 Conference, pp 57–61 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By G R. Power

A useful way to assess potential productivity of SLC mines is by quantifying tonnes/drawpoint/day to be extracted from the mine. However limited industry information has been published to help mines benchmark this number. This paper assesses industry data which can be used to support estimates of potential productivity from new mines based on tonnes/drawpoint/day. The information used has been extracted from historical production schedules which indicate what was achieved, rather than what was planned. It has been assessed using an algorithm created for the purpose and is presented with discussion of varying definitions of active drawpoints, analysis of the data and inquiry into some of the underlying contributing factors.

Mar 15, 2021

By A Trench, S Ulrich, S Hagemann

A synthesis of reported All-In Sustaining Costs (AISC) for 57 Australian gold mines in the period 2014–2016 reveals for the first time the clear influence of grade upon cost performance, most evident in gold-only underground mines. Past syntheses of costs on a single quarter basis have viewed grade as potentially subordinate to other factors such as production scale, mine geometry, mineralisation style and a combination of other mining-related costs. Better understanding of the grade to cost relationship on both an individual mine and whole-of-portfolio portfolio basis is needed. Insight into the roles and trade-offs between other cost-determining factors will aid the future sustainability of the gold mining sector in Australia and assist in targeting prospects for future resource growth and development. While the overall trend is toward higher-grade mines displaying lower costs and vice versa, the grade to cost functions appear radically different between mines based on time-series data. The median cost of Australian gold production in the final quarter of 2016 was A$1081/oz. The threshold for lowest cost quartile production was A$965/oz. Underground production now dominates Australian gold output – with 71 per cent of ounces originating from operations that are either entirely underground or hybrid pit/underground mines. Scale economies are evident, with smaller mines predominately among the higher cost producers. For mines of equal grade, open pit mines are lower cost than underground operations. Reserves are modest, with a median mine life for underground operations of 4.7 years based on current production rates. Reserve additions at mines are likely constrained not only by the finite nature of mineralisation at each mine but also by the geometrical difficulty of accessing suitable drilling locations to test for reserve extensions.CITATION:Ulrich, S, Trench, A and Hagemann, S, 2017. Towards an understanding of production costs at Australia’s underground gold mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D J. A Van Zyl, J C. Cunning

Technological advances associated with the expanded application of paste technology in underground mine backfilling are now stimulating an interest in the disposal of process tailings as paste in the surface environment. Concurrent with the development of alternative surface tailings disposal practices is the requirement to fully understand the consolidation behaviour of tailings in paste form, and to relate this understanding to the significant body of data and operating experience from decades of study of the performance of hydraulically placed tailings. One effective method for demonstrating the benefits derived from handling and placement of tailings as paste is to review tailings slurry consolidation theory from the perspective of the changes which take place in the material as it makes its transition from a loose slurry to a dense, stable deposit resulting from managed thin-layer deposition. For a typical process tailings, an example is provided which illustrates the effect which mechanical dewatering has in accelerating the consolidation process and thereby providing a range of benefits from the perspective of surface disposal. Increased rates of filling (rise), expanded use of upstream embankment construction methods and elimination of impounded surface solutions are some quantifiable benefits which can be assembled on a site-specific basis to allow for valid comparisons with more traditional approaches to tailings disposal.

Jan 1, 1998

By Bigu J, Grenier M. G, Knight G

Particulate control is a major concern in underground mining and the subject of continuing research world wide. In Canada the federal government's Mining Research Laboratory at EIIiot Lake, Ontario, has been using two aerosol counters to aid its investigations. Specific studies with the units include: a) evaluating total and elemental size efficiencies of dust filtration units: b) characterizing the dust particulate cloud from different mining operations: and c) determining dust transportation characteristics.

Jan 1, 1988

By H Jalalifar, N Aziz

In the ten years since the University of NSW proposed a pillar design methodology for bord and pillar operations, the Australian coal mining industry has changed substantially. What was primarily a bord and pillar design approach is now being applied to chain pillar design in longwall mines where the requirements are substantially different. The dimensions of chain pillars can impact on tailgate conditions (roof, rib and floor), seal performance, and surface subsidence. The status of chain pillar design practice in Australia is reviewed, with a focus on defining pillar strength, chain pillar loading, and assessing the performance of the roof/pillar/system. A new pillar strength equation is proposed for Australian coal that applies for all width/height ratios. An alternative analysis of probability of failure of chain pillars is presented.

Jan 1, 2005

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By M Saghaeian, A H. Baladastian, A Dehghani Ahmadabadi, V Sheikhzadeh, R Hejazi

With the declining of high-quality hematite and magnetite iron ore reserves and the increasing accumulation of material resulting from mining and beneficiation operations that appear as lowquality depots and discharged materials in tailing dams, the necessity of recycling these reserves is increasingly becoming a critical demand. The Chadormalu iron ore mine is among the largest deposits of magnetite-hematite iron ore in Iran. In this mine, the total wet processing tails accumulated in tailing dams are over 92 Mt containing 25–40 per cent Fe. Laboratory and pilot tests on tailing samples led to the design and implementation of the Chadormalu Tailing Recovery plant (CTR) with a unique process circuit in Iran. In the CTR plant, after three steps of re-pulping with spiral classifiers and sanding machines, the underflow is concentrated by two stages of WMIMS and produces 64 per cent Fe grade magnetite concentrate. The tailings of the drums are mixed together and introduced into the hematite recovery section, including two stages of VPHGMS separators, and 60 per cent Fe grade hematite concentrate is produced. This plant has been in operation for over ten years with a total yield of 18.93 per cent. Due to changes in the materials extracted through new tailing dams, the quality of the final concentrate dramatically dropped to 56.36 per cent Fe and 0.79 per cent P; therefore, applying reverse flotation and removing phosphorus from the final concentrate was inevitable. By using this approach, upgrading of the concentrate to 63.01 per cent Fe and 0.05 per cent P was obtained. Furthermore, regarding the high amount of phosphorus in the tailing streams, direct flotation has been designed to produce apatite concentrate as a by-product stream through a flotation system comprising series banks of Rougher, Cleaner, and Re-Cleaners flotation cells. Hence based on the results, at optimum conditions, a final apatite concentrate with a yield of 15.78 per cent and 14.06 per cent P could be achieved. Successful implementation of this project has led to the production of magnetite-hematite and apatite concentrates with annual capacities of 250 000 and 45 000 t, together with total yields of 11.59 per cent and 6.19 per cent (includes de-sliming of apatite flotation feed), respectively.

Aug 24, 2022

Contemporary approaches to safety management appear to be failing short of meeting its mark in improving mine safety. This is evidenced by the high workers compensation, high incidence rates and fatalities. Evidence from high-risk and complex organisations points towards safety culture as being important in improving site safety. In more recent years resilience engineering has been touted as a new and innovative way of managing safety. This paper reviews and synthesises previous literature on safety culture and resilience engineering. It then highlights methods that can be used to measure safety culture and resilience engineering, and explores similarities and differences between complex organisations and gold mining to identify opportunities for more innovative approaches to improving safety in gold mining operations through safety culture and resilience engineering.

Aug 1, 2010

By D Bradshaw, J R. R de Villiers

The non-stoichiometric sulfide mineral pyrrhotite (Fe(1-x)S), common to many nickel and platinum group element (PGE) ore deposits, occurs in varying crystallographic forms with the different types exhibiting subtly different physical and chemical properties. These differing properties are likely to influence the flotation performance of pyrrhotite, which in the case of PGE operations is actively recovered, whereas in nickel operations pyrrhotite is depressed. In this study, examination of natural pyrrhotite samples from Southern African and Canadian nickel and PGE ore deposits revealed a variety of pyrrhotite compositions in terms of iron content (Fe7S8, Fe9S10, Fe11S12) and solid solution nickel concentration. Pyrrhotite composition was correlated with its mineral association depending on whether non-magnetic pyrrhotite occurred in conjunction with troilite, non-magnetic pyrrhotite occurred as single phase pyrrhotite, magnetic pyrrhotite occurred as single phase pyrrhotite or whether the two phases; magnetic and non-magnetic pyrrhotite co-exist. Subsequent microflotation tests of selected single phase pyrrhotite samples revealed that the non-magnetic pyrrhotite is slightly more floatable than magnetic pyrrhotite. Microflotation tests also showed that varying flotation responses occur between differing magnetic pyrrhotite samples. These differences in flotation performance are postulated to be a result of the effects of varying pyrrhotite crystallography, trace metal content and mineral association on pyrrhotite oxidation, formation of surface species and subsequent adsorption with xanthate collector.

Jan 1, 2008

Mining operations in the Obuasi mine of AngloGold Ashanti Limited began in 1897 using mainly gravity concentration and amalgamation to recover the gold from predominantly high-grade quartz ores. The mine is primarily an underground operation, although some surface mining still takes place. Ore is currently processed by two main treatment plants: the Sulfide Treatment Plant (STP) for underground ore and the tailings treatment plant for tailings reclamation operations. STP was commissioned in February 1994 to treat 180 000 t/m of double refractory gold ore and it hosted the then world's largest commercial scale bacterial oxidation plant which uses Gencor's BIOX« technology. Gold is recovered by gravity and flotation, with the regrinding of the sulfide concentrate before bio-oxidation to liberate locked gold in sulfi de minerals. The BIOX« product is leached using the carbon in leach (CIL) process. Gravity gold recovery is a major component of STP operations and its contribution to overall plant recovery is about ten to 13 per cent. Gravity recovery has undergone series of technological upgrading, since the very first circuit which consisted of a Knelson concentrator and a Gemeni shaking table which was incorporated into the milling circuit at the start of the plant. Presently, each of the gravity circuits which consists of Knelson concentrator(s), cyclones and Gekko InLine Reactors (ILR), are located at the Milling and BIOX« circuits. More recently a new gravity recovery facility comprising of four 48 inch Knelson concentrators and cluster of ten inch cyclones have been incorporated at the tail of the flotation circuit. An additional ILR will be commissioned in 2010 to treat the concentrate generated from the new Semi Autogenous Mill #2 (SAG 2) Knelson: concentrator tower under construction. Since the inception of STP, significant gravity recoverable gold has been recovered via Knelson concentrators and the employed circuits have seen a number of modifications and upgrades, motivated by ore mineralogical changes and recovery concerns. The pioneering adoption of the ILR technology in 2001 and 2003 was a critical factor in enhancing the improved recovery benefit of the gravity circuits. Therefore the objective of this paper is to highlight the mine's experience in the gravity recoverable gold process with emphasis on plant modifications and gravity equipment upgrade. Operational challenges and the contribution of gravity gold to overall plant recovery are also discussed.

Aug 1, 2010

By Medhurst TP, Trueman R

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface mod- elling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model pre- dicted the fender would suffer considerably more de- formation and strain.

Jan 1, 1992

By M Forbes, R Jeuken

Brownfields geoscience measurement such as drilling and surface geophysics can be costly and it is often difficult to weigh the cost of data collection and processing against the value it unlocks at the time of extraction. This makes it difficult to prioritise geoscience expenditure and find the optimum intensity of geoscience activity across competing assets. There are multiple options for managing resource uncertainty and spatial variability through mine planning and resource engineering such as varying marketing strategy, adjusting stockpile or other infrastructure design and product blending. Consideration of these alongside increased data collection further complicates finding a comparable value of geoscience programs to determine the right blend of geoscience measurement and engineering controls. Concepts similar to Value of Information (VOI) analysis which is applied to strategic planning can be used to estimate the value of geoscience measurement and pit sequencing at tactical planning and operational timescales. This involves the quantification of resource uncertainty and prediction of how it will affect resource extraction. This paper outlines this process and demonstrates its use to prioritise geoscience at BHP Coal Assets. The value of infill drill programs in enabling operational stability is quantified and compared the value of engineering controls like increased stockpile capacity. This study supports that idea that the application of VOI methods to bulk mining at tactical time horizons has potential to inform geoscience planning and resource engineering not just separately, but as part of a unified strategy for managing resource uncertainty.

Mar 22, 2022

By A J. Minns

This paper addresses the question: how can the minerals industry remain viable; viable in the sense that we are able to access land for exploration and discovery, we are able to develop and operate mines (and processing plants) safely and profitably and we are able to close operations in a responsible manner, so that modified landscapes are restored to acceptable community standards?Many of the answers to this question can be addressed through the theme of this conference û that of eco-efficiency. The eco-efficiency concept is very useful, since it does help to translate principles of sustainability into business value at the operational level. To provide some context to how this can be achieved, the paper discusses what is happening at the international level, outlines some key industry initiatives within Australia and then discusses what work is being done within companies.

Jan 1, 2004

By A D. Pradana, D R. Pradana, Y H. Putra, Z Zulhan, T Hidayat

The high temperature processing of nickel laterite ore is currently dominated by the Rotary Kiln- Electric Furnace (RKEF) technology. The ratio of SiO2/MgO (S/M) in the ore is one of the critical parameters that determines the success of the RKEF process. Incompatible S/M ratios in the ore can cause aggressive chemical interaction between the slag and MgO refractory. The slag-refractory interaction at conditions relevant to nickel laterite ore smelting was investigated in the present study. Synthetic mixtures representing the slag compositions of nickel laterite ore smelting were prepared by mixing MgO, SiO2, Al2O3, CaO, Fe2O3, and Fe and heating the mixtures in steel containers at 1300°C under an argon atmosphere for 3 hrs. Pure MgO crucible were used as containment material in the melting process of the mixtures to represent the MgO refractory. The kinetics of the slagrefractory reaction were investigated using samples with selected initial S/M ratios of 2.0 and 3.0 (wt/wt) (with constant CaO = 3 wt per cent, Al2O3 = 5 wt per cent, FeO = 10 wt per cent) by performing melting at 1500°C in MgO crucibles for 5, 30, and 120 mins under an argon atmosphere. The effect of the S/M ratio in slag on the slag-refractory interaction was also investigated by performing melting of mixtures with different initial S/M ratios of 1.75, 2.0, 2.5, and 3.0 (wt/wt) in MgO crucibles at 1500°C for 120 mins under an argon atmosphere. After the melting process, each sample was quenched in water, mounted in resin, ground, polished, and coated. The interaction between the slags and MgO refractory was then evaluated by analysing the polished samples using a scanning electron microscope equipped with an energy dispersive spectroscopy (SEM-EDS). Thermodynamic simulations using FactSage™ 8.0 thermochemical software were performed based on the experimental slag compositions, refractory, and conditions to support the evaluation process. The results show that a higher S/M ratio in slag leads to a higher tendency for the refractory component to dissolve into the slag. A higher S/M ratio in slag also leads to an increasing extent of solid-state diffusion of iron oxide into the remaining refractory grains. The dissolution of MgO into the slag is rapid; the MgO concentration in the final slag increased by 2.4 wt per cent and 5.7 wt per cent at initial S/M ratios of 2.0 and 3.0 wt/wt, respectively, within 5 and 30 mins of the melting process.

Aug 21, 2024