Search Documents

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

By E N. Sajin

The final arsenic bearing waste products at the majority of metallurgical and chemical enterprises are cakes in which arsenic is present in the form of calcium arsenate. Burial of cakes demands construction of special burial sites and does not guarantee reliable protection from arsenic penetration into the ground and surface waters. Under laboratory conditions we developed technology for processing calcium arsenate cakes with obtaining low toxic products suitable for long-term storage, meeting environmental requirements. The investigations have shown that thermal processing of briquetted mixtures of cakes containing 15 - 20 per cent weight of pyrite under the temperature of 873 - 923¦K during 45 - 60 minutes gives briquettes sufficiently hard for transportation and long-term storage. Arsenic, under high sulphidisation temperature is bonded into low solubility non-volatile iron sulphide bearing compounds having chemical properties similar to the natural arsenic compounds. Solubility of the obtained products in neutral, acid and alkaline media was investigated during long period of time (three to 12 months). It was determined that arsenic content in the solutions did not exceed the norms for cultural and welfare basins and fish-ponds.

Jan 1, 2002

By Lees M. G, Vitnell B. W

The post-war need to increase coal production promoted an intensive drilling campaign. Ineffectiveness in core recovery inclined the coal industry towards percussion drilling rather than diamond drilling. The Joint Coal Board, recognising the greater potential of core drilling, has actively encouraged improvement in techniques and equipment. One outstanding need was a barrel which, over and above other improvements being achieved, would permit recovered core to be examined before it had been subjected to the increased fragmentation and displacement which to date has been inevitable except in core which has been drilled in solid sticks û as New South Wales coal rarely can be drilled. In conjunction with Triefus Pty Ltd a barrel with a split inner tube has now been evolved, as a result of which, core can be more accurately logged, division in to lengths for analysis more aptly made, any core loss more reasonably allocated to appropriate plies, and a greater percentage of core recovered û of the order 95 per cent and more. The one half of the split inner tube is lifted from the other and the logging completed before the core is disturbed.

Jan 1, 1957

The Illawarra District, from 50 to 100 miles south of Sydney, is one of the State's important coalfields. It extends from Clifton on the north, to the Shoalhaven river on the south, and from the coast westward beyond the coastal scarp.For descriptive purposes, this area falls naturally into two zones:(a) the coastal belt backed-by the eastern edge of the plateau;(b) the plateau, westerly from the coastal scarp.(a) The Coastal Belt.A triangular shaped area extending from Clifton to the Shoalhaven river, composed for the most part of soft coal measures strata of Permian age, which, on weathering, undermines the massive overlying Mesozoic sandstones and causes the gradual recession of thecliffs.South of Wollongong, upper marine sediments and contemporaneous igneous rocks make their appearance beneath the coal measure beds and occupy the greater portion of the coastal belt.(b) Plateau Area.Extending westerly from the coastal escarpment is a plateau known as the Robertson Tableland, composed of Triassic sandstone and shales dipping gently in a northerly direction, and capped in places by Wianamatta. shales and r.rertiary basalts. This tableland is approximately 2400 feet above sea level in the vicinity of Robertson, and gradually falls to about 750 feet at Waterfall.The plateau area for the most part is highly dissected, rough, steep gorges alternate with sharp ridges.A large part of the northern watershed of the Robertson tableland is a reserve for Sydney water supply, and large dams have been constructed at Cataract, Avon, Burke, and Cordeaux.

Jan 1, 1938

The maximum current density at which conventional copper electrowinning plants will result in satisfactory, adherent, and dendrite·free cathodes is determined by the thickness of the diffusion boundary layer. A decrease in the value of that thickness will permit an increase in the current density. This fact is utilized to develop a high current density cell in which the reduction of the boundary layer thickness is accomplished by means of a specially designed electrolyte circulation system. The high current density cell is used to determine the effect of current density on such process parameters as current efficiency, cell voltage, power consumption, and cathode purity. A number of empirical equations are developed for the purpose of estimating the magnitude of these effects.

Jan 1, 1972

By D Morrison, P Goodman

The cycle time between adjacent stopes is critical to achieving the required production rate from 3500 Orebody; one of the Enterprise Mine orebodies. Current Mt Isa cemented fills require a 90-day cure period which had to be cut to 30 days while maintaining the required strength criteria. The Enterprise Mine Feasibility Study recommended that this be achieved by Cemented Slurry Rock Fill (CSRF), but that on-going research into paste fill be continued. The continuation of the research, in conjunction with overseas visits has recommended that the 3500 Orebody be filled with paste fill, with the potential to fill other orebodies. The paste fill will comprise cyclone and thickener dewatered copper tailings to which Portland Cement (PC) is added before vertical borehole delivery and undergound pipeline reticulation to individual stopes. The benefit is not only re-use of copper tailings but also much reduced binder usage.

Jan 1, 1998

By N Bianco, D Drinkwater

The professional skills shortage is intensifying, and commentators are predicting a shortfall in supply of qualified professionals for the mining industry, ranging from thousands to tens-of-thousands by 2020 (Tuckwell, 2011; Scoble, 2011; Laurence and Hebblewhite, 2011). Human resources are already stretched, and university graduates arriving in the workplace are often moved rapidly into management positions where there is limited scope to develop their engineering proficiency. This process may well be developing excellent young managers, but our industry is producing fewer excellent young engineers (Munro and Tilyard, 2009). Many believe that it is engineering excellence that is likely to be the key to our industryÆs success in the decade to come. An innovative in-house graduate development program has been created by specialists at the JK Centre in partnership with two mining companies. This program, known as MetSkill«, has been running throughout 2012. Groups of graduates have had to identify a process plant optimisation opportunity and embark on a structured program of data collection and analysis, facilitated by a æteaching teamÆ of researchers and consultants from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. This group project culminates in a report-back session to senior company officials. Along the way, a series of short workshops and other activities provide opportunities to work on specialist skills, and support is also offered by senior technical specialists from the companies involved.This paper outlines key features of the MetSkill« program, along with a report-card on progress in 2012 and plans for further program development in 2013.CITATION:Drinkwater, D and Bianco, N, 2012. Developing minerals industry leaders by encouraging metallurgical excellence, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 287-290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The Torington Lodes.This paper describes investigations into mineralogical, petrological and structural associations of cassiterite in occurrences of economic value. The work was carried out in three mines, during a number of years, in the hope that the, data collected might be helpfulin the search for occurrences of cassiterite in stanniferous zones and reduce unproductive exploratory work. Tin-bearing lodes at Torington, in the New England district, New South Wales, have been worked since 1880, and the locality is the most important centre of lode tin occurrence in the, State. The township of Torington is 18 miles westerly from Deepwater, a station on the Great Northern Railway, 446 miles from Sydney.The tinfield forms part of the Mole Tableland, which has an altitude between 3,000 ft. and 4,000 ft. above sea level. The country rock, in which the stanniferous lodes occur, is granite of Permian age, which has been intruded into Carboniferous claystone. An inlierof claystone is exposed to the west of the stanniferous area, 'and in it, close to' its contact with the enclosing granite, are occurrences of wolfram and bismuth. These minerals, together with chalcopyrite, pyrite, arsenopyrite, zinc blende, galena and molybdenite, in very small quantity, are associated with cassiterite in lodes traversing the granite, particularly near the claystone, but decrease in amount with distance from the contact. Their occurrence is sporadic and usually causes no trouble in dressing the cassiterite concentrate, the final product containing less than 1% of total penalisable impurity. In Curnow's mine, pyrite, galena and molybdenite have been observed at 700 ft. from surface.The granite is of the biotite type and its structure may be divided into four groups, or classifications, arising from segregation processes during cooling and consolidation. The four classes, in order of extent of distribution, are:1. Granite of normal type, in which the constituent quartz felspar and mica, have a particle size approximately 14, in.2. Porphyritic granite, in which the felspar particles are from % in. to lin. in size, that of the quartz and mica approximately % in.3. A fine-grained granite, in which the particles of all constituent minerals are % in. or less in size;4. A rock of highly siliceous ground mass containing very small particles of felspar and almost negligible biotite.Type 1 is the general type of granite in all mines of the field; types 2 and 3 may occur as large masses, or all three classes may merge rapidly one into the other, and all be disclosed in 20 ft. of driving. Usually, however, the segregations are massive, but are not associated with any special horizon. For instance, a mass of porphyiiticgranite extends from surface to a depth of 440 ft., for a distance of 350 ft. south from the New England main shaft. The upper levels of Curnow's mine, 14" mile south-east, are in normal granite, but a restricted mass 'of porphyritic granite occurred between Nos. 5 and 6 levels, or 400-500 ft. below the collar of the shaft...

Jan 1, 1950

By Mills R, Shannon W. T, Finch J

As an extension to investigations into methods of upgrading the Iitania content of ilmenite concentrate from beach sands using 100 g/day, a small pilot plant treating 23 kg/ day of ilmenite was used.In the pilot plant the iron oxide in the ilmenite was reduced to iron at 1200°C using carbon (coal/char) without melting the material, using a tunnel kiln heating cycle, the charges contained in saggars, The iron was then separated from the titania fraction by ball milling, wet magnetic separation, and screening. The resulting magnetic product was high in iron (about 80 per cent Fe) and the non-magnetic product high intitania (about 70 per cent TiO2).From this trial sufficient data were obtained to enable the preparation of a flow sheet for a plant producing 62,300 tonnes/year total products, and an estimate of costs to be made. This has shown that for an estimatedcapital expenditure of nearly $6,000,000 and annual production costs of about $4,000,000, the cost per tonne of high titania product (76 per cent TiO2) would be nearly $70.

Jan 1, 1977

The objectives of this paper are two-fold. First, it will show what problems can arise when single estimated values are substituted for a distribution of values when evaluating an open pit mine project in the face of uncertainty. Secondly, it will show how the ability to deal with uncertainty and risk in mine project evaluation can have a significant impact on the ownersÆ and stakeholdersÆ investment decision-making. Here a new mine evaluation framework, the integrated valuation/ optimisation framework (named IVOF), is introduced as an alternative tool for mine project evaluation where uncertainty and risk are incorporated in the evaluation process.

Jan 1, 2009

By R Handfield, G Kary, Frieda Project

Recent exploration by the Cyprus Amax-Highlands Pacific-OMRD Joint Venture at the Frieda River project, PNG has demonstrated the extent of igneous phases, alteration and mineralisation, and the relationships between the various mineralisation styles in this major Cu-Au porphyry-epithermal system. The project area is in the obducted volcano-sedimentary section of the New Guinea mobile belt 78 km NE of Ok Tedi. It is between two major NNE dipping faults interpreted to have undergone thrusting then sinistral shear in the Late Miocene to Recent. The Frieda River Igneous Complex is a 15 km +7 km ovoid area with a central pod of basaltic andesite volcanics with cogenetic diorite to quartz diorite subvolcanic intrusions, and flanking clastic sediments. A series of late-stage, hornblende quartz diorite plugs ring the main igneous mass. The igneous rocks have a normal K calc-alkaline character with a very limited compositional variation. The intrusives are exposed on the eastern flank of the complex and have five mappable units and numerous defined phases. The southeastern quarter of the complex is host to a cluster of at least seven stockwork porphyry copper and skarn-hosted deposits within an area of 4.5 +3.5 km. The Horse-Ivaal and Koki deposits have identified resources totalling 804 mt @ 0.46 per cent Cu and 0.3 ppm Au, and the other deposits are in various stages of exploration. All these deposits are related to the Horse Microdiorite phase of the Complex and are outlined by a zone of potassic-propylitic-SCC alteration. Local overprinting argillic and advanced argillic alteration is related to a separate, post-porphyry mineralisation intrusive phase. The recent emphasis has been on the identification of higher-grade zones using ideas of structural control and specific intrusive-alteration-mineralisation relationships within the known resource areas. An elongate area 13 km x 4 km in the centre of the Complex has advanced argillic alteration in the volcanic rocks. This alteration zone hosts the Nena deposit (52.8 mt @ two per cent Cu and 0.7 ppm Au) and approximately 20 prospects of high sulphidation type. These deposits are distributed along two prominent NW-trending siliceous ridges interpreted as regional scale structures. Nena is a pod of vein and replacement sulphides hosted in a tectonically controlled multiphase breccia that overprints the advanced argillic alteration. The Nena deposit is 4 km from the nearest of the major porphyry occurrences. It is underlain by basemetal veins and minor porphyry mineralisation that are related to the Flimtem Trachyandesite intrusive phase. The recent search for additional Nena-type ore has focussed on the siliceous ridges using detailed structural and geochemical ore control criteria. Widespread, but poorly mineralised, basemetal-bearing carbonate and sulphate veins form a ring around the mineralised area. These veins have sericitic selvages, cut the porphyry mineralisation, but are cut by and locally underlie the silica-alunite phase of the advanced argillic alteration. The current model is that there are discrete intrusive phases responsible for each of major hydrothermal events at Frieda. These include from oldest to youngest:the Koki phase has no related alteration or mineralisation; the dominant Frieda phase has the hornfels, early skarn and minor magnetite-chalcopyrite mineralisation; the Horse phase has the bulk of porphyry copper and skarn-hosted mineralisation and minor basemetal veins; the peripheral Knob phase is barren; and the Flimtem phase has the high sulphidation epithermal deposits and minor porphyry and vein mineralisation. The intrusive phases span the interval 17 to 11.5 Ma and are co-magmatic. They represent discrete batches off the parent magma, rather than simple fractionation products.

Jan 1, 1999

By R Dwyer, S Rea, W J. Bruckard, N McSweeney, R Holmes

"The innate ability of microorganisms to adapt to changing or inhospitable environments has often been exploited for industrial purposes and forms the basis of many current biotechnological processes. The ability of bacteria to adapt and adhere to specific mineral surfaces ensures that the energetic or nutritional requirements of the cell are met and often serves as a survival mechanism under unfavourable?growth conditions or conditions of stress. In this process, cells may rearrange or modify the macromolecules expressed on the cell surface itself or produce extracellular molecules, modifying mineral surfaces to render them more suitable for growth. The modifications that these molecules produce on mineral surfaces may result in changes to the surface charge and hydrophobicity of a mineral. As a result, these biomolecules may have some potential application as flotation collectors or modifiers.In this work, the effect of long-term exposure of Paenibacillus taiwanensis to goethite and common gangue minerals associated with Australian iron ores on the differential expression of membrane and extracellular proteins was determined. Both groups of proteins play a role in cell adherence to mineral particles. Cells were adapted to grow in the presence of each mineral over time. The proteins expressed on the cell membrane and the extracellular proteins excreted by the cell were isolated and analysed by two-dimensional polyacrylamide gel electrophoresis (2D gel PAGE). The outcomes of these studies are presented here and potential application of these products for flotation discussed.CITATION:Dwyer, R, Rea, S, McSweeney, N, Bruckard, W J and Holmes, R, 2013. Microbes and their metabolites - potential iron ore flotation reagents, in Proceedings Iron Ore 2013, pp 369-372 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By I Thin, L Morizzi, C Seymour, G Mungur

Olympic Dam has been investigating mine design options for the South Mine Area (SMA), which will continue using the existing sublevel open stoping (SLOS) method. The SMA is an undeveloped mining area, located south of the existing underground mining areas currently in production at Olympic Dam. The SMA study reached the stage where geotechnical inputs were required for stope design, infrastructure location and ground support forecasts. A large database of geotechnical data was collected to inform open pit designs for the ODX (Olympic Dam expansion) project (resulting from 659 drill holes). This geotechnical data has since been reprocessed to align with design inputs required for the SLOS mining method. The result has been the construction of a preliminary three-dimensional mining rock mass model (MRMM) that has been incorporated into preliminary stope mine design and infrastructure layout assessments, which have taken into account the predicted prevailing ground conditions.As with any model, it is necessary to improve the confidence in its predictability; therefore the model must be calibrated. The preliminary SMA MRMM was no exception. First pass calibration was possible with results from underground geotechnical window mapping from exposed rock mass conditions in the lateral development and surface geotechnical holes for ventilation shafts.The SMA project continues to advance and has started a program of resource drilling. Selected holes have been identified that target data limited areas. This will ensure that the data gaps are infilled in order to maintain the required data density required to improve the model confidence. In addition, further underground window mapping in the SMA will provide ‘mine scale drill hole’ data that can be used to either update the MRMM or as part of planned future calibration. Stope performance data from stopes will provide further valuable data for calibration purposes.The proposed paper will present the process and findings that have been followed in order to establish a well calibrated geotechnical model that can be used with an acceptable level of confidence in the ongoing refinements of the mine design and planning process for the SMA.CITATION:Thin, I, Morizzi, L, Mungur, G and Seymour, C, 2016. Building and calibration of a geotechnical model for sublevel open stope design at Olympic Dam, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 523–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

In the early stages of opening up a mine, when there is some uncertainty as to its future career, necessitating caution in laying out works of a permanent character, the want is often felt of an assay furnace, easily built and easy of transportation, should the" mine " prove to be " no mine." Again, cases occur in which parties buy the right to treat comparatively small heaps of tailings, and then shift their plant to other localities. Under these circumstances it is necessary to restrict the plant to the barest necessaries, to suit, so to speak, the nomadic character of the work.An assay furnace that is really portable, easily transported, erected, taken down, of little weight, always ready for action on short notice, is indeed in these cases a desideratum which has long been wished for. The gasoline furnaces introduced intothe Australian market some time since practically fulfil these conditions; but they have the fatal drawback of being dependent on a constant supply of the liquid fuel, gasoline, which is seldom, if ever, obtainable locally in' any wayback mining township...

Jan 1, 1904

The Resource Management Act 1991 (RMA) and the Crown Minerals Act 1991 (CMA) both came into force on 1 October 1991. The purpose behind RMA was to integrate the existing laws dealing with town and country planning, land subdivision, water and soil, minerals and energy resources, coastal management, air pollution and noise control into one omnibus Act. Originally, there was a section in RMA dealing with minerals. However, this section was taken out of RMA and a companion piece of legislation - namely CMA - was passed with RMA.

Jan 1, 1994

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

A recent Evening Post Headline read 'Officialdoms Inertia Risking Millions in Growth Strategy'. The article beneath that headline outlined the difficulties encountered by the Government's growth strategy projects and included the paragraph 'public efforts by Government to brush up communication of the widespread nature of its growth strategy is believed to have been matched by efforts in private by some ministers to overcome their frustration at the constant delay while reports and paper work are moved between departments and through the system'. The article went on to point out that these delays could cost New Zealand millions of dollars in lost overseas exchange savings. We as responsible citizens should be appalled or at least concerned that such costly delays should or even could occur. But those on the outside of the system who spend much of their working life prodding, reminding, pleading, cajoling, even begging, the bureaucracy should be excused a smirk or a smile or even a good belly laugh. The Minister is usually a part of the bureaucracy passing judgment on someone else's proposals. This time the Government has plans of its own. Plans which it wishes to see implemented as rapidly as possible and even with the assistance of the precautionary National Development Act with its 'fast track' provisions those plans have got bogged down in the bureaucratic machine which this Government has done as much as any other to create. In the circumstances, the thought of Her Majesty's Ministers frustrated at the constant delay while reports and paper work are moved between departments and through the system is not unpleasing.

Jan 1, 1982

Mineral deposits in New Zealand whose origin can be ascribed to primary magmatic segregations are associated with mafic-ultramafic complexes related to two orogenic episodes which took place during Palaeozoic and Mesozoic times. These mafic-ultramafic complexes are essentially of two types. One is ophiolitic and has podiform chromite mineralisation presumably formed below a spreading ridge. The other type occurs as intraplate layered intrusions in which Fe-Cu-Ni sulphides and Fe-Ti-V oxides have formed as a result of liquid immiscibility with the host magma, and have subsequently accumulated by gravity means. Generalised descriptions are given for some deposits in NW Nelson, Fiordland and Marlborough districts.

Jan 1, 1980

By Sharpin P. C

The countercurrent gas-solid heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temperature distributions through the drier have been calculated. Although the calculations rest on several simplifying assumptions, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating conditions on the rate of drying of the briquettes which controls the strength of the char produced. The analysis shows why a limitation was reached in the improvement of char strength in the pilot plant in 1961 due to the performance of the drier and a prediction is made of a way in which the limitation could be overcome.

Jan 1, 1966