Search Documents

By Russell G. Wayland

This paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948

By W. J. Reagan

IN a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the vari-ous sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In. the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable 'indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2 in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be involved.

Jan 1, 1936

By Russell G. Wayland

This paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948

By C. S. Sivil

To modern civilization the platinum metals are of inestimable value. Their distinctive properties, both physical and chemical, render them indispensable in an age in which the processes of the laboratory are becoming an essential part of the daily life of the world. Generally, their function, though vital to particular processes, is not spectacular, and so remains unknown to all except the operators. EARLY METHODS OF MANUFACTURE The properties of platinum were recognized as of prime importance for scientific work at. a very early date, probably between 1750 and 1760. The difficulty of making articles from it seemed almost insurmountable, because no means of attaining the temperature necessary to melt it were known at that time. It is true that solid platinum could be obtained by fusing the metal with a more volatile metal such as arsenic, which was subsequently driven off by baking, but such a method, at its best, would give only a very brittle product, which was totally unsuitable for the purposes for which it was intended. Little, if any, progress could be made until it was discovered that platinum sponge, heated to white heat and hammered in an iron or clay mold, would metallize and retain the shape of the mold. This was a process that could not be wholly satisfactory but from it developed the method of pressing the sponge in a mold and forging it at white heat into wire or sheet. At present a somewhat similar process must be used for fabricating articles of tungsten, molybdenum and other metals of high fusing point, as with these metals we face today the same problems that the scientists of the eighteenth century encountered with platinum, but possibly the next significant advance in the metallurgy of these metals will be the devising of means to melt and cast them.

Jan 1, 1931

By AIME AIME

CONCIDENT with what promises to be a record-breaking year of activity in the world's greatest iron-ore district is the announcement of plans to hold the regional meeting of the American Institute of Mining & Metallurgical Engineers at Duluth, Aug. 12 to 15 in¬clusive. More than 25 open-pit mines will be in operation in Minnesota's great iron-ore district this year, affording to those attending the convention an unusual op¬portunity of viewing practically side by side the interesting activities of power-shovel operations, railway haulage, truck haulage, conveyor-belt haulage, tower-excavator operations, iron-ore concentration, and underground mining. The ore can be followed from the mines to washing and concentrating plants and to the docks and lake carriers on Lake Superior, where an average of one boat of 10,000 tons' capacity will be loaded and depart every 15 minutes, day and night, during the 1941 shipping season.

Jan 1, 1941

By David P. Hale

The Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,' but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1942

By David P. Hale

The Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,' but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1942

Smoky Valley Mining Company, Round Mountain, Nevada, was the pioneer operation designed for large scale heap leaching of crushed gold ores. It is located in the Big Smoky Valley which stretches 160 km (100 miles) through central Nevada west of the Toiyabe Mountain Range. Gold was first-discovered at Round Mountain, 88 km (55 miles) north of Tonopah, in 1905; and mining in the area included placer operations, which ran from 1946 to about 1960. Smoky Valley Mining Company is a partnership of Felmont Oil Co., Case-Pomeroy & Co., and Copper Range Co., with the latter being wholly owned by Louisiana Land and Exploration Co. In 1969, an option on the Round Mountain property was acquired by Copper Range, and during 1974 a decision was reached to proceed with mine development and plant construction. Ore reserves were reported at 10,537,000 mt (1 1,617,000 st) of 2.09 g per mt (0. 061 oz per ton) gold using a cut- off grade of 0.69 g (0.02 oz). Silver content was approximately 2.4 g per mt (0.07 oz per ton) and the waste to ore ratio was about 1: 1. By the end of 1976 heap leaching was in operation. The ore is a rhyolite tuff, sometimes described as a gold porphyry with highly abrasive qualities but which does not break down into slimes upon contact .with cyanide solutions. Gold is unevenly distributed through the ore but as a whole it is in a very finely divided state. Climatic conditions are extreme in central Nevada. Summers are hot and dry while winters are windy and cold with subfreezing temperatures. Elevation of the property is about 1,920 m (6,300 ft). Precipitation averages 203 mm (8 in.) per year. Until February of 1980, leaching was continued until the temperature reached minus 2ºC (28º F), and about 10 months leaching was the average. Water for the operation is drawn from the Toiyabe Mountains through a 13. 7 km (8. 5 mile) pipeline, originally installed in 1915, or from wells in the valley bottom. The plant requires make-up water at the rate of about 1,500 liters per min (400 gpm). On a schedule of three shifts, seven days per week, the daily output at Round Mountain amounts ,to 12, 700 mt (14, 000 st) consisting of 6,350 mt (7,000 st) each of ore and waste. Ore is hauled with a fleet of 45 mt (50 st) trucks and dumped into the 1,0.70 by 1,650 mm (42 by 65 in. ) gyratory primary crusher located near the pit. The primary

Jan 1, 1981

By Walter P. Jenkey

[ ] I. THE REDUCING ACTION OF CARBON AND OF HYDROCARBONS. Carbon has long been recognized as one of the most powerful reducing agents in the deposition of ores. Investigations, made by myself, of the zinc- and lead-deposits in Southwest Missouri, in the region centering about Joplin, where the formation of the metallic sulphides has been due to the action of bitumen, carbonaceous shales and bituminous coal, Lace afforded abundant evidence that the solid oxygenated hydrocarbons, particularly, when in fine powder and in suspension in the waters circulating through the ore-bodies, are the most energetic and powerful reducing agents known. Bitumen, liberated by the decomposition of the ore-bearing limestone, is found in the Joplin mines in all degrees of fluidity and hardness, dependent on the amount of oxidation it has undergone. From semi-fluid maltha it grades into partly oxidized mineral-pitch, which, by further oxidation, changes to hard asphalt, finally breaking up, from continued absorption of oxygen, into a fine powder resembling in appearance powdered coal. In this condition oxidized bitumen, from its light gravity, is transported readily in suspension in the underground circulating-waters. Bituminous coal and black carbonaceous clays and shales occur as surface formations, often in intimate association with

Jan 1, 1913

By AIME AIME

[The American Institute of -Mining Engineers does not assume responsibility for any statement of fact or opinion advanced in its papers or discussions.] A detailed list of the' papers contained in this section is given in the Table of Contents, pages i. and ii. Comments or criticisms upon all papers given in this section whether private corrections of typographical or other errors or communications for publication as "Discussions," or independent papers on the same or a related subject, are earnestly invited. ERRATA. The following corrections and. additions to papers contained in Bi-Monthly Bulletin No. 7, January, 1906,-were received too late for incorporation in the text of said papers ; but will be introduced in their: proper places: in the volume of the Transactions: These corrections are here published in order to bring them -promptly to the notice of the Institute. Page Line Cover, title-page and at the top of pages in the preliminary section "No. 1 " should be "No. 7 ". 1. Bottom For :" Dr. P. H. Shimer" read "Dr. P. W. Shinier " 69. Fig. 3. "N" of compass-record should be ?S". A new block for this illustration has been made as shown on p. xxxviii of this Bulletin. 78. 3 from bottom. For " slope " read " stope." 89. Fig. 2, small diagram in upper left-hand corner. Omit use 50 ft. to 1" scale ". For "Thro' 250 " read " Thro' 200 ". Add dotted line extend¬ing from upper right-hand corner of the square

Mar 1, 1906

By R. Wang, N. J. Grant, B. C. Giessen

By crystallographic and X-ray methods, the existence and isonzorphism of Ti3Rh5 and Hf3Rhs were confirmed. Both phases are of the orthorhombic Ge3Rh5 type; lattice parameters and refined positional parameters are given. The structure is related both to the filled-up NiAs-B8 and Cu-AI types. An analogous phase with zirconium does not exist; the effect of ternary substitutions for titanium ad hafnium suggests a size factor limit to be active. A recent survey of phase diagrams of the T4 metals titanium, zirconium, and hafnium with the T, noble metals rhodium and iridium indicated the existence of the A3B5 phases Ti3Rhs, ZrsRhs, and HfsRhs. Ti3Rhs and Hf3Rh5 were found to be isostructural, based on the line-rich powder patterns which had not been analyzed. Zr3Rh5 was considered to have a substructure of the NbRu type (orthorhombically distorted B2-CsCl type).&apos; Because, in combinations with other transition metals, hafnium and zirconium are generally more likely to form isostructural phases than hafnium and titanium (with the significant exception of the Ti2Ni-"E93" type phases based on T4 metals2), the reversal of this relation for the A3B5 phases was of interest. As shown in the following, the nonexistence of Zr3Rhs has been established, the structures of Ti3Rh5 and Hf3Rh5 have been worked out, and crystal chemical relationships and stability criteria are reported. EXPERIMENTAL METHODS AND RESULTS Alloy Preparation and Phase Diagram Work. Alloys were prepared from high-purity (99.99+ pct) elements by arc-meltin3,4.Heat-treated alloys were annealed in a vacuum of 3 x X torr for 24 hr at 1300DC. Metal-lographic samples were etched electrolytically in concentrated HCl with 5 v ac for 5 min.3 X-ray diffraction powder patterns were taken on a GE XRD-5 dif-fractometer with Cum radiation at low scanning rates (0.2 deg per min for 28). It was confirmed that Ti3Rhs and Hf3Rh5 have similar diffraction patterns, and that an alloy with the composition Zr3Rhs has a different pattern. Six Zr-Fh alloys with 59 to 69 at. pct Rh were therefore prepared and investigated in the as-cast state by X-ray diffraction and metallography. Alloys at 59 and 61 at. pct Rh were found to be a single phase, with the distorted B2-CsC1 type structure typical for the off-stoichio- metric region of the phase (Zr,-,Rh,)Rh. This phase forms a eutectic with ZrRhs at about 66 at. pct Rh: accordingly, alloys between 61 and 69 pct at. pct Rh consisted of two phases. There is no evidence for the existence of Zr3Rh5. Based on the results in Rafs. 1 and 5, on the present work on Zr-Rh, and on several additional alloys investigated, the portions between the AB and AB3 stoi-chiometry for Ti-Rh, Zr-Rh, and Hf-Rh are as follows: Further, several ternary alloys near Ti3Rhs and Hf,Rhs were prepared in which it was attempted to replace titanium and hafnium partly by zirconium, niobium, tantalum, and germanium. The results will be discussed in a later section. Structure Determination of Ti3Rh5. Since Ti3Rh5 and Hf3Rh5 are isostructural, the following discussion will largely deal with the former. Although the powder pattern of TisRhs is complex, as found previously,1 it could be indexed by comparison with other structures of A3Bs stoichiometry. Ti3Rh5 was found to be isostructural with Ge3Rh5, whose orthorhombic structure had been elucidated by Geller.9 As both the sizes and atomic numbers of germanium and titanium are comparable, the unit cell volume and the peak intensities could be expected to be similar; however, significant differences exist in the atomic positions, as will be shown. All lines in the powder patterns of Ti3Rh5 and Hf3Rhj could be indexed with primitive orthorhombic unit cells with the lattice constants: The fractional errors are 10 The low-angle portion of the indexed powder pattern of Ti3Rh with sin2 8 < 0.30 is listed in Table I. The extinction laws Okl only with k = 2n and hOl only with h - 2n are compatible with the space group Pbo2 and the more symmetrical space group Phnm of Ge3Rh5. Finally, the positional parameters of Ti3Rh5 and HfsRhs were refined under the assumption that titanium and hafnium occupy the germanium positions in Ge3Rh5. Integrated intensities were obtained from the diffraction patterns by planimetry. Intensities of overlapping reflections were separated by an iteration process incorporated into the least-squares positional refinement program according to a method described previously. The intensities of Ge3Rh5 were used in the first separation cycle, while the atomic parameters of Ge3Rh5 were used as starting values in the first refinement cycle. Absorption due to specimen

Jan 1, 1970

By H. M. Rutherford

THE reflection method in seismic prospecting has aroused much interest in the past few years. The purpose of the present paper is .to present the method of reflections in the mapping of geologic structure and also to give some indication of its limitations. The reflection method is well adapted to the mapping of geologic structure in the Mid-Continent fields, and has been found most useful there. The refraction method is ideally suited to the finding of structures, such as domes, where the amount of relief is very large. This explains the brilliant success of the refraction method in the Gulf Coastal region of Texas and Louisiana. The additional fact that salt has a much higher velocity than the sur-rounding sediments made their discovery much easier. By the use of the reflection method, differences of relief of 25 to 50 ft. to the mile may be detected at a depth of 5000 ft., and the depth points accurately plotted on a map. This is hardly possible by the use of the refraction method. The reflection method has been in almost continuous use in the Mid-Continent area since 1926, but very little, if anything, has been published until recently(7) ? regarding either the method or the results. The dis-covery of several oil fields is now attributed to the use of the reflec-tion method. Reflection methods have been used by the Germans to find the thick-ness of the ice of several glaciers. (2,8) The depths there considered were of the order of only a few hundred feet. For the method to be of any practical value in this country, it must be able to work to depths of several thousand feet. As was indicated above, this is now possible, though there are many problems connected with the reflection method yet to be solved. The refraction method requires that the shooting be done over long ranges. It was necessary, for example, to take distances out to several miles in order to penetrate some five thousand feet. Naturally this uses a good deal of dynamite. In the reflection method the distances are much shorter and the amounts of dynamite are much smaller, within limits which will be noted below. The chief distinction between refrac-tion and reflection methods is to be found in the analysis of the seismo-gram. Refraction shooting makes use of only the first arrival of energy

Jan 1, 1932

By D. S. Choi, H. von Schonfeldt, H. D. Dahl

The design of pillars around a longwall panel in which the effect of the adjacent and worked-out panel is taken into consideration is discussed. A mathematical model is used to duplicate field observations such as opening closure and pillar rib movement. The model is then used to predict the effect of changes in mining geometry on the opening stability.

Jan 1, 1976

Edgar Hall, Tenterfield, New South Wales (communication to the Secretary): Mr. Klepetko* asks for information showing at what percentage antimony and arsenic, as impurities, begin to affect injuriously the quality of brass.

Jan 1, 1899

By L. G. Graper, E. L. Ramsey

The present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. Adding Sulphur as a Sulphite These difficulties can be avoided if sulphur is introduced into the stecl by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which—upon decomposition—forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast—that is, before rolling— and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions arc more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. Results As stated before, the sulphur dioxide is added to steel by means of the decomposi- 27

Jan 1, 1942

By James Pollock

SUMMARY THE possibility of colloidal deposition of cinnabar has been neglected. In opalite deposits cinnabar exists in particles within or near the colloidal size range. Colloidal processes have been admitted to be operative in hot springs and low-temperature deposits similar to most cinnabar deposits. Mercuric sulphide sols are stable to elevated temperature and pressure, and in nature probably are chiefly affected by the electrolytes in solution, dilution of colloid, and presence of protective colloids as silica. The stability of mercuric sulphide sols to electrolyte is measured, and shown to be greatly increased by dilution and by the protective action of silica. Mercuric sulphide sols follow the Schulze-Hardy valency rule, therefore the precipitating power of complex mixtures of electrolytes can be computed roughly. The stability of mercuric sulphide sols is shown to be greater than the equivalent precipitating power of the electrolytes in a hot spring depositing mercuric sulphide. It is concluded that finely divided or earthy types of cinnabar are colloidally deposited. POSSIBILITY OF COLLODIAL DEPOSITION While colloidal solution has been suggested as a means of transport for a number of minerals, such as the sulphides of antimony, arsenic, and iron, it has been neglected in connection with mercury. This is surprising because there exists positive evidence that cinnabar is present in certain deposits in particles of colloidal or near colloidal size. Colloidal transport could result from either the rapid dilution or neutralization of alkaline sulphide solution bearing mercury coming in contact with deep ground waters, or from colloidal solution near the original source and subsequent flow to the point of deposition unchanged. That the dilution of a mercuric alkaline sulphide solution will precipitate mercury sulphide in colloidal form has been demonstrated a number of times and is easily confirmed. The dilution hydrolyzes the alkaline sulphide Na2S to the corresponding hydroxide and hydrosulphide NaOH and NaHS, and the diminution of the concentration of alkaline sulphide reduces the solubility. It is not the contention of this writer that colloidal deposition is the mode of transport of mercuric sulphide in all mercury deposits, but that the stability of a mercuric sulphide sol, as demonstrated below, in waters that are similar to those that have deposited mercuric sulphide necessitates consideration of this possibility in many deposits, especially those of the hot-spring and so-called opalite type. EVIDENCE OF COLLOIDAL DEPOSITION Ross1 has shown that most deposits of quicksilver are formed at low temperatures and pressures, and probably by solutions that have relatively simple chemical compositions. In most cases the solutions are probably similar to those observed in hot springs, and in two instances-at Steamboat Springs, Nevada, and Sulphur Bank, California-hot springs have been reported by Becker as actually depositing cinnabar.2 Opalite deposits were believed by early investigators to be surface phenomena

Jan 1, 1944

By E. F. Sturcken, J. W. Croach

A grain orientation distribution function, P(u,F), was developed for use in predicting physical properties in oriented metals. Examples are given of the use of the function to predict thermal expansion coefficients in rolled uranium rods and plate. The P(u,F) function was synthesized from X-ray difpaction intensity measurements, Ii, norrnally used to plot inverse pole figures. The symbols u and F specify the angles that the crystallographic axes of the grain make with the normal to the sample surface and P(u, F) gives the number of grains oriented in each direction, (u,F). P(u,F) is obtained from a least squares fit of the Ii to an orthonormal set of spherical harmonic functions. The P(u, F) function was also used to define a quantity, J, which is a measure of the departure of the orientation distribution from unifomzity (or "randomness"). The J parameter may be used to follow, quantitatively, the amount of preferred orientation induced as a function of mechanical working or heat treatment. An example is given of the application of the J parameter to prefevred orientation studies of hot- and cold-rolled uranium rods and hot-rolled uranium plate. Because P(u,F) is derived from relative intensity measurements by the powder diffraction technique, it is applicable to material with large absorption coefficients and/or grain size and is particularly suitable for characterizing the preferred orientation of large numbers of samples such as fuel elenzents for a nuclear reactor. IN general the physical properties of an oriented metal depend on the direction in which the properties are measured. Hence to predict physical properties the grain orientation must be known as a function of the direction of the specimen. The conventional methods of expressing preferred orientation measurements are the pole figure1 and the inverse pole figure.2-8 Both methods are difficult to use for predicting physical propertiess because they are graphical and because they are stereographic projections and hence are not "area-true." In the present report a quantitative orientation distribution function, P(u,F), is synthesized from pole density measurements normally used to plot inverse pole figures. For inverse pole figure plots the pole densities, pi, are obtained by powder dif-fractometer intensity measurements of their reflections from a flat surface of the sample, normal to the direction of interest. Each pole density, pi, represents a single orientation, i, and is proportional to the volume of material with orientation, i; hence a set of pi gives an approximation for the general orientation for the sample direction measured. The expression8&apos;7 for calculating the pole densities, pi, from the diffraction measurements was previously

Jan 1, 1963

By James E. Berryman

A method is presented for calculating the pressure depletion performance of a gas-condensate reservoir from the original reservoir fluid composition using the laboratory determined pressure-production history and retrograde liquid accumulation as guides. Equilibrium vaporization ratios for this calculation were modified from published data until the calculated dew point pressure and retrograde liquid accumulation agreed with the values observed in the laboratory. The calculated results are compared with the produced gas composition determined by low temperature analysis during constant volume laboratory experiments of pressure depletion behavior. This comparison shows that the calculation procedure is adequate for determination of gas phase composition. Data from field separation tests in low temperature separators are presented which verify the applicability of published equilibrium vaporization ratios for a wide range of separator conditions. INTRODUCTION A reliable prediction of the pressure depletion performance of a gas-condensate reservoir is necessary in determining reserves and evaluating field separation methods. The predicted performance is also used in planning future operations and studying the economics of projects for increasing liquid recovery. Because the flow of fluid in a volumetric gas-condensate reservoir is usually single phase flow, the pressure-depletion per-formake is primarily a function of the phase behavior of the reservoir fluid. The properties of a gas-condensate system of major importance are: (1) compressibility factor at reservoir temperature and pressure; (2) dew point pressure; (3) composition changes of the vapor phase with pressure depletion; (4) recovery of original in-place hydrocarbons at any pressure; and (5) retrograde condensate accumulation. These properties are most generally determined by a pressure depletion-type experiment on recombined separator gas and liquid samples in the laboratory. ldeally the pressure-depletion performance can be calculated from the composition of the original reservoir fluid if the reservoir temperature and initial pressure are known.1,2,3 It has been reported "... comparison of such computations with depletion-type ex-periments on recombined samples in the laboratory have yielded results that appeared to be entirely adequate.". The success of such calculations is determined by the equilibrium vaporization ratios chosen, especially those for the higher boiling point hydrocarbons. It is the purpose of this paper to present a method for computing the change in composition of the vapor phase during pressure depletion by production using laboratory determined properties of the system to guide the calculation and to illustrate the use of the method with data from the Cockfield "D" sand of Washington field, St. Landry Parish, La. Results of field tests and laboratory analysis are included. As a result of this reservoir fluid study, a cycling program has been evaluated, the fidd has been unitized, and the cycling started in July, 1956.

Jan 1, 1958

By L. G. Graper, E. L. Ramsey

The present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. Adding Sulphur as a Sulphite These difficulties can be avoided if sulphur is introduced into the stecl by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which—upon decomposition—forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast—that is, before rolling— and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions arc more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. Results As stated before, the sulphur dioxide is added to steel by means of the decomposi- 27

Jan 1, 1942

By Albert C. Harding

For several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. Description Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare wither-ite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. Occurrence All known commercially important barite deposits in the United States occur as re- placements or cavity fillings in schists, shales, limestones, dolomites, and quart-zites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. Table i—Crude Berile Sold or used by Producers in 1945 State Short Tons Arkansas................... 260.660 Missouri.................... 225.467 Georgia..................... 110,393 Tennessee................... 32,812 Nevada..................... 28,919 Other States............... 37,811 Total..................... 696,062 (&apos;other states,, included only california and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. Consumption The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium ------- chemicals Total 720,903 tons

Jan 1, 1949