Search Documents

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

By W. Julian Patron

TREATMENT of the breaker wash-water discharges to remove the suspended particles of finely divided material is usually most efficiently and economically accomplished in settling or thickening tanks. The purpose of these tanks is to separate the excess water from the solids by sedimentation whereby the solid particles suspended in the water are thickened by the force of gravity. The water overflowing these tanks is either reused for coal cleaning or discharged directly to the streams. The settled solids, which are in a relatively concentrated condition, forming a sludge or thick pulp, can be disposed of by pumping to a storage dam, by slushing into mine workings, by processing for recovery of coal, or filtering by vacuum or centrifugal means and discharging with the breaker refuse. The scope of this paper will be limited to the discussion of settling and thickening equipment, the factors that influence the settlement of solids, and a brief description of tests that can be made to determine the size of settling facilities required for any particular condition. The practical application of sedimentation to the treatment of coal falls into two groups, one of classification or hydro- separation, and the other of clarification and thickening. Classification may be employed to prepare a relatively low- grade fuel, which can be used as is or can be further processed separately. Clarification and thickening is employed where the primary objective is to recover a relatively dewatered solid and return a satisfactorily clear water to breaker or streams. When a stream of water flows across a tank, the time required for a particle to travel from the feed inlet to the overflow must be a little greater than that required for the finest particles or flocs in the feed to settle out of the stream. OPERATION AND TYPES OF SETTLING EQUIPMENT Theoretically, the liquid in a settling tank should rise at a more or less constant rate throughout the area of the tank Under these conditions the rising velocity of the water must be less than the settling rate of the finest particles if clarification is to be obtained. When classification of particles is to be made in the tank, the overflow velocity must be greater than the settling velocity of the particles that are to be removed with the tank overflow. The performance of a settling tank, then, depends on the settling rate of the solids and the current velocities in the tank. The oldest types of sedimentation employ intermittent types of settling tanks of any convenient shape. Means are provided for filling the tank with pulp and allowing it to settle until quiet, for moving the clean liquor and for removing the thickened sludge. The operation is necessarily intermittent but a sufficient number of tanks is employed so that a continuous flow of clear water is maintained. Continuous methods for the sedimentation of slurries were developed in the metallurgical industry. Cones from which settled solids were discharged by gravity

Jan 1, 1946

By G. A. Koehler

The Hiawatha mine, a producer of iron ore, is near the City of Iron River, in Iron County, Michigan. This mine, operated by The M. A. Hanna Co., has been chosen by the author as a typical iron mine in this district that is using the cut-and-fill mining system. General Geology The Hiawatha ore body lies along the steeply dipping north limb of a syncline that closes around on the east end to form a bathtub-shaped structure. Throughout this major structure there are very many smaller wrinkles or folds, which vary the direction as well as the thickness of the ore body. The total length of the ore formation with minor interruptions so far developed is about 3600 ft. The ore body throughout the entire present depth of 2000 ft. has averaged approximately 40 ft. in thickness; it is somewhat narrower at the upper levels and shows a marked increase in thickness on the bottom levels. This increase in thickness probably indicates that the bottom of the trough is near or that a major monoclinal fold has been encountered, which flattens the ore and gives apparent horizontal thickening. The footwall of this ore body is generally a black, graphitic slate, very rich in iron sulphides, quite combustible when exposed to air, and very treacherous to handle during mining operations. The hanging wall, in most places, is a cherty, fairly hard iron formation, and in general stands quite well ill open stopes. There are places, however, where black slate is found in both the hanging wall and the footwall, which makes mining difficult, as the black slate tends to slough off after being exposed to air. In these places it becomes necessary to leave a scale of ore 5 to 6 ft. thick on both hanging wall and footwall, which is not recovered. Fig. I shows a typical vertical cross section through the Hiawatha ore body. Type of Stoping Because of the size and shape of the ore body and the hard, dense structure of the ore, sublevel stoping has been an efficient and economical method of extracting the ore. This method, with various minor changes, has been used since the mine was opened in 1893. There have never been any stope-filling operations, however, until recent years, when crushing of pillars and black-slate fires forced the issue and methods were arrived at to fill all stopes. Development of Deeper Levels Shaft sinking to deeper levels in development operations has been done successfully by two methods without interference or hindrance to production. These systems are: I. Sinking an auxiliary winze a short distance from the shaft, then drifting back to the shaft location and putting up a pilot raise through to the bottom of the shaft. This raise is always in the manway compartment of the shaft, so that no work is ever done under a cage or skip. A 20-ft.

Jan 1, 1946

By Arthur Flagg

(New York Meeting, February, 1913.) THE Elk City mining district of Idaho occupies a position near the geographical center of Idaho county, a region of mod¬erate elevation in the western foot-hills of the Bitter Root mountains. The district comprises an area of approximately 350 sq. miles, bounded oil the west by the Newsome district and on the south by the Dixie and Oro Grande districts. There are no mining districts to the north or east. Elk City, the principal town and the seat of the mining office for the district, is situated in a hydrographical basin surrounded by low hills. The elevation is 4,200 ft. above sear level. Through this basin flow Elk Creek, Red river, and American river, which unite west of town to form the south fork of the Clearwater. The one township is set out from the Bitter Root Forest Reserve. Though a railroad starting from the Stites terminus of the Clearwater Short Line of the Northern Pacific railroad has been under consideration for some years, the camp is yet with¬out railroad facilities. The projected road would follow the south fork of the Clearwater on easy grades, but would be very expensive to build and maintain. While such a road would greatly benefit those who are now operating in the camp, and in a slight degree stimulate interest in its possibilities, there is hardly business enough to warrant its construction.

Jan 4, 1913

By H. I. Aaronson

Isothermally formed plates of proeutectoid a, lengthen at approximately the rates predicted by the Zener-Hillert equation, indicating that their lengthening kinetics are controlled by the volume diffusion of chromium in the ß matrix. Solution annealing treatments in the vicinity of the transus introduce a second mode of transformation, in which the lengthening rate is at least 1.8 x 104 faster than predicted by this equation. Little or no volume diffusion appears to accompany the latter transformation. The Presence of oxygen is evidently a Prerequisite for the occurrence of this reaction. X HE effects of thermal history prior to the initiation of transformations which proceed by nucleation and diffusional growth are currently evoking considerable interest. The rate of nucleation (but not the rates of growth) of pearlitel and of bainite,2 and the over-all rates of aging reactions in Al-cu3 and Al-si4 alloys have been shown to be appreciably dependent upon thermal history in the solid-solution region"' or in the two-phase region prior to the onset of pre~ipitation.3,4 In none of these reactions, however, was the transformation mechanism changed by variations in the temperature-time path used to reach the reaction temperature. Preliminary experiments reported by M. K. McQuillan5,8 and a systematic investigation by Farrar and Margolin7 have disclosed that the transformation behavior of hypoeutectoid Ti-Cr alloys is considerably more sensitive to thermal history. Qualitative evidence strongly suggests that not only the rate of nucleation but also the rate of growth and even the mechanism of the ß — a reaction can undergo remarkable changes when a solution annealing treatment in the vicinity of the ß/a +ß, or transus temperature, is interposed between a high-temperature solution anneal (conventionallq at 1000°C) and the isothermal reaction treatment. The present investigation was undertaken in an attempt to ascertain the nature and origin of these effects. Study of the changes in the kinetics and morphology of the ß - a, reaction produced by varialtions in thermal history was the primary means employed for this purpose. EXPERIMENTAL PROCEDURE The compositions of the alloys used in this in~esti~ation are given in Table I. These alloys were homogenized for 5 days at 1050° C in evacuated (2 x 10 -5 mm of Hg), zirconium-gettered fused quartz capsules. The capsules themselves were enclosed in a porcelain chamber evacuated with a mechanical pump during the homogenization anneals. Upon completion of homogenization, the alloys were cooled to room temperature and then reheated to 550°C for 3 1/2 days in order to transform the alloys to a finely divided mixture of a and TiCr2, and thus provide an approximately constant initial mi-crostructure. Individual specimens were sealed in evacuated and internally gettered Vycor capsules and heat treated as previously described.8,9 EXPERIMENTAL RESULTS Ti-10.64 Pet Cr. This investigation was largely performed on the 0.64 pet Cr alloy. The "base"

Jan 1, 1962

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By H. Shaw

In the author's previous paper an attempt was made to analyze in detail the gravitational effects arising from certain subterranean anomalies of simple form, and extending to infinity in three directions. As a result of this critical examination, certain features—which were considered to be characteristic of the anomalies under investigation—were disclosed, a close observance of which enables a complete interpretation to be reached. The most simple case was first considered; viz., that of a heavy horizontal plate, bounded above and below by horizontal planes, and extending to infinity on one side of a vertical plane containing the y axis, in the three directions + y, —y, and +x. After this, the investigation was extended to the case of a similar infinite horizontal block having an inclined face. In each case the form and behavior of the gradient curve and the curve of differential curvature were analyzed, and entirely distinct interpretations were put forward, based upon (1) the gradient, (2) the differential curvature and (3) a comparison of these two quantities. In continuation of the previous work, and as a preliminary to further analysis of more complex structures, certain factors will now be examined which characterize (1) the simple infinite vertical block and (2) an infinite block which is inclined to the vertical, formations which are of considerable practical interest, being typical of important. geological structures—intru-sive dikes, lodes, veins, etc.—and because, even though in nature these may be irregular, valuable guides to a more complete interpretation are obtained by assuming, as a first approximation, that they have the simple characteristics to be studied hereafter. In the previous paper certain preliminary assumptions were made in order to render the resulting deductions universally applicable and entirely independent of the particular scale employed. Consideration was limited to homogeneous deposits of unit positive effective density (and this condition is retained in the present investigation), so that in the case of

Jan 1, 1932

By F. V. Lenel, G. S. Ansell, M. J. Salkind

An experiment is described in which the growth of interparticle necks in an array of loose spherical silver powder at temperatures near 300°C was determined by measuring changes in the electrical resistance of the array. The activation energy for neck growth of contacts was derived by abruptly changing temperature and noting the change in the rate of neck growth. Since the experiments were run under an external load, the changes in activation energy with stress could he determined. The activation energy was found to decrease rapidly with increasing stress. It is concluded that the material transport in the experiments is one of plastic flow by dislocation motion. The variation of activation energy with stress is typical for cross slip of dislocations, an important material transport mechanism in the temperature range investigated. THE process in which powder compacts or aggregates of loose powder are held at an elevated temperature under an external load is called hot pressing or sintering under pressure by powder metallurgists. In this investigation the early stages of this process as applied to loose spherical silver- powder aggregates were studied. The powder particles were approximately 100µ in diameter and the temperature was near 300°C, i.e., below one half of the melting point of silver in degrees Kelvin, where volume diffusion is not expected to contribute to sintering. In the process, the contact or neck areas between powder particles grow. Since this involves plastic deformation of the particles under a constant external load (even though not under constant stress) it would be termed creep by mechanical metallurgists. On the other hand, the growth in neck area observed in compacts or loose-powder aggregates held at elevated temperature without the application of an external load is termed sintering by powder metallurgists. During sintering the major driving force is the stress due to surface tension. However, even when no load is placed on the compact or powder aggregate, an external stress, i.e., gravity, plays an important role in sintering in addition to those stresses arising from surface tension, as was shown in two previous investigations.'" It is therefore postulated that no sharp dividing line can be drawn between the phenomena of "creep" and "sintering". Different material transport mechanisms may be involved in either of these phenomena, but they will depend upon the temperature and the level of stress, but not necessarily upon the nature of the driving force: surface tension or external load. At the low temperatures of this investigation, an external stress much higher than the stress due to surface tension is necessary to obtain measurable rates of neck growth. In order to avoid misunderstanding this phenomenon will be called "creep". The rate of growth in contact area in the loose silver-powder aggregates was determined by meas-

Jan 1, 1965

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By Charles J. Potter

There are many sources of energy available for consumption. Some available are solar, tide and wind. However, in terms of relatively large usage, only four principal sources are used for primary energy today. They are coal, oil, natural gas and water power. Such additional items as wood and nuclear energy, although supplying quantities of energy today, do not in the aggregate amount to any real significant quantity, but nuclear energy must be considered for future use. In addition, such a thing as gas from distillation of coal and oil is not considered primary energy. The principal markets for primary energy are the electric power utilities, space heating, industrial uses and transportation. The electric utility use of energy is primarily from coal, followed by natural gas and water power. Space heating is primarily a gas market, followed by oil and then coal. Space heating by electricity is only considered in the generation of electric power. Transportation's principal source of energy is oil. Coal has practically no market left in this field.

Jan 4, 1962

By W. M. Weigel

Salt production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been cstimated only by geophysical methods. The diameter of the salt core varies from less than 1/2 mile to over 2 miles. Only domes where the salt is comparatively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use. Fig. 1 shows the location of the domes so far developed for commercial salt and brine. Nos. 1, 2, 4, 7, 8, 9 and 10 are in the Gulf Coastal field,

Jan 1, 1938

By W. M. Weigel

Salt production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been cstimated only by geophysical methods. The diameter of the salt core varies from less than 1/2 mile to over 2 miles. Only domes where the salt is comparatively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use. Fig. 1 shows the location of the domes so far developed for commercial salt and brine. Nos. 1, 2, 4, 7, 8, 9 and 10 are in the Gulf Coastal field,

Jan 1, 1938

By R. W. Ph. D. Raymond

PROFESSOR W. P. BLAKE, in a note to his Catalogue of California Minerals, pointed out that the mining districts of the Pacific slope are arranged in parallel zones, following the prevailing direction of the mountain ranges. This interesting generalization has been more fully illustrated and connected with the geological history of the country by Mr. Clarence King, who sums tip the observed phenomena as follows: "The Pacific coast ranges upon the west carry quicksilver, tin, and chromic iron. The next belt is that of the Sierra Nevada and Oregon Cascades, which, upon their west slope, bear two zones, a foot-hill chain of copper mines, and a middle line of gold deposits. These gold veins and the resultant placer mines extend far into Alaska, characterized by the occurrence of gold in quartz, by a small amount of that metal which is entangled in iron sulphurets, and by occupying splits in the upturned metamorphic strata of the Jurassic age. Lying to the east of this zone, along the east base of the Sierras, and stretching southward into Mexico, is a chain of silver mines, containing comparatively little base metal, and frequently included in volcanic rocks. Through Middle Mexico, Arizona, Middle Nevada, and Central Idaho is another line of silver mines, mineralized with complicated association of the base metals, and more often occurring in older rocks. Through New Mexico, Utah, and Western Montana lies another zone of argentiferous galena lodes. To the east, again, the New Mexico, Colorado, Wyoming, and Montana gold belt is an extremely well-defined and continuous chain of deposits." These seven longitudinal zones or chains of mineral deposits must

Jan 1, 1873

By D. McLean

For many pu@oses uniform strength is desired over a long temperature range, coupled to a band of softness at the hot end for easy shaping. Various types of material fulfill such a requirement to different degrees, depending on the regularity of their atomic structure. In long-chain polymers and vitreous glasses the irregular structure leads to a steep temperature dependence of deformation resistance and the temperature band between the hard and brittle condition and the soft condition is only about 100 C. In crystals and especially metals the atomically regular structure leads to a much smaller sensitivity over a wide temperature band, thus approaching the ideal behavim. The reason for this insensitivity is that the regular crystalline structure deforms by the movement of dislocations and the elastic interactions of dislocations in- PLASTICS, GLASSES, AND CRYSTALS The ease or otherwise of deformation varies with temperature much more in some substances than in others. This is an important matter when service over a wide temperature range is needed, especially volve energies of several hundred electron volts compared with which the energy of thermal agitation is insignificant. However, temperature affects a metal's defmmation resistance through its influence on the annealing, m coarsening, of the three-dimensional dislocation network. This coarsening is a phenomenon very similar to grain growth and ideas about grain growth can be applied to it. Taking into account also the temperature dependence of the glide resistance from alloying additions, a reasonable account can be given of the overall effect of temperature on deformation strength and of stress and grain size on deformation rake. Special structures me described. some arising from these ideas and as yet untried, which may benefit metals and polymers but not ni-treous glasses. when in addition a degree of softness suitable for shaping is required at some stage. It would be nice if one could write on this subject in as much detail about plastics, glasses, and so forth, as about metals, but there has been far more study of this matter in metals than in other substances, which is one reason why most of this paper concerns metals. However, in Fig. 1 there are shown the deformation strengths of several nonmetallic substances as a function of temperature. In many tests the attempt at deformation caused breakage and the graph lines are then drawn dashed. Long-chain plastics, a glass, and a crystalline substance are included in Fig. 1. The notable feature of all of them is the sensitivity of the

Jan 1, 1969

By Fred C. Bond

There is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool [or the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1943

By Fred C. Bond

There is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool [or the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1943

By C. L. Sollenberger, Will Mitchell, Ford F. Miskell

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By J. W. Martin, L. K. Singhal

Grain boundary M23CB precipitates have been shown to form by a process involving the migration of an austenite grain boundary, and each plate of precipitate is in parallel orientation with one of the austenite grains constituting the boundary. The carbide distribution and morphology appear to be sensitive to grain boundary mis orientation. Some areas of austenite grain bowzdary permit the development of an array of M,C, particles, some of which are in parallel orientation with one grain and some with the other grain constituting the boundary. Massive carbide at grain boundary triple points is also shown to be in parallel orientation with one constituent grain. PREFERENTIAL precipitation during aging of carbides of the type (Fe,Cr)23C6, usually written MZ3C6, in grain boundaries of quenched austenitic stainless steels has been widely recognized. M23C6 has a complex cubic crystal structure' which contains ninety-two metal atoms and twenty-four carbon atoms per unit cell. Less energy is involved in forming grain boundary precipitates than in the formation of intragranular precipitates, and the process is further enhanced by the accelerated diffusion rates in the boundaries and by the probability of segregation of chromium atoms and carbon atoms to the region of the grain boundaries during prior solution heat treatment in order to reduce lattice strain. Early electron micrographic studies2, 3 involving either extraction replica or normal replica techniques established the geometric or dendritic form of the carbide particles, although this approach led to dis- pute as to whether the particles grew within the plane of the boundary or grew into the matrix.4-6 More recent thin-foil studies' have claimed to identify a discontinuous precipitation process involving M23C6 at grain boundaries, and the object of the present work was to attempt to clarify the situation using modern electron micrographic and diffraction techniques. 1) EXPERIMENTAL 1.1) Material. The steel selected for this work had a base composition of 24 pct Ni-25 pct Cr-3 pct Ti and contained about 0.04 pct C. The full analysis if given in Table I. This alloy was in the form of strip which had been hot- and cold-rolled to a thickness of 0.6 mm. 1.2) Heat Treatment. Specimens 4 cm long by 1 cm wide were solution-heat-treated for 3 hr in argon at 1150°C, followed by water-quenching. Specimens were subsequently aged in vacuo at 750°C for periods up to 500 hr. 1.3) Preparation of Electron Microscope Specimens. The heat-treated strips were cut bv spark machining into discs of 3 mm diam and 0.6 mm thickness. he-discs were dished on both sides using an electrolytic jet of 15 pct HCl electrolyte at 80 v. Final electro-polishing of the discs was carried out using 10 pct perchloric acid, 20 pct glycerol, and 70 pct ethanol at 10 v. The current density was kept below 300 ma. cm"2 by cooling the electrolyte to 0" to 5°C. As soon as a small hole appeared, the electropolishing was stopped and the specimen was quickly washed with ethanol.

Jan 1, 1969